Search Documents

The feasibility of exploiting a mineral deposit by developing a surface mine is closely related to the environmental protection and land reclamation costs. This issue has utmost importance for West Macedonia Lignite Centre (WMLC) of Greece, where there is still a lot of interest for opening of new mines and for further development of the existing open-pits. The decision-making process in these cases can be based on a decision tree that takes into consideration the various cost components of environmental management, the alternative solutions, the environmental permits and the cost reports of environmental management actions carried out so far. Moreover, the mine planning procedure is affected indirectly by numerous uncertain environmental and socioeconomic parameters, such as the delays caused by the bureaucratic procedures and the settlement of arguments in the Court.

Jan 1, 2006

By Thomas F. Pugsley, Wilf J. Davies, James Gallagher

Falconbridge Limited is developing a major nickel mine at Craig which lies between 600 m, 915 m and 1500 m below surface and is accessed on the 600 m and 1250 m levels of Onaping Mine. To supply adequate ventilation for mine development and initial ore production, two raises, 1200 m long are to be driven in norite and granitic gneiss. Falconbridge has purchased a Robbins 97RL Raise Drill and a string of 330 mm drill pipe to ream these raises in 600 m legs at diameter. The paper describes the introduction of deep hole, large diameter raise boring technology into Falconbridge operations involving contractors and specialists in the technology.

Jan 1, 1989

By K. Brady

Making progress on sustainable development will require greater attention to the management of materials produced from mine exploration through use to reuse, recovery and recycling. Material stewardship is a concept that embodies the range of activities required for optimal and appropriate use of minerals and metals in society. The following paper provides an overview of some recent initiatives that promote the stewardship of minerals and metals in society. The initiatives described are being conducted by organisations ? the International Zinc Association, the Canadian Copper & Brass Development Association and the International Council on Mining & Metals. These associations illustrate stewardship activities at three different levels: - an international association representing companies that produce a range of minerals and metals; - an international commodity association; and - a regional association. For each initiative, information is presented on its development, scope and outlook. This paper draws heavily from work of the associations but the viewpoints are the responsibility of the authors.

Jan 1, 2007

By Betty L. Gibbs

Mine planning and scheduling done with computer programs is possible only after extensive work has been completed to define the geologic extent of an ore body and an overall mine design. Mine planning methodology on computer can vary from computerized engineering tasks through systems which completely optimize a plan with little input from an engineer during the actual scheduling process. However, a strong emphasis is placed on producing practical mining sequences which may be "best" rather than "optimum". This section offers several viewpoints on the planning process using computers. Interactive planning and scheduling systems are attractive for many companies because they are easy for engineers to understand, and the results are acceptable. The engineer develops an open pit mine sequence by trial and error using interactive graphics. The results of this approach can usually be improved. A computer program can help an engineer make many trials in a short time period and provide a higher level of confidence that a "best" plan has been generated.

Jan 1, 1989

By E. D. Seymour

Minera Yanacocha operates a complex heap leach gold facility in the Northern Andes of Peru. Four leach pads and thirteen solution storage process ponds form an extremely complex system. Distinctly different wet season and dry season rainfall accumulations present unique challenges to the process water balance. Minera Yanacocha operates four excess water treatment facilities which discharge water to the environment at specific quality standards in order to maintain a balanced system. Numerous government agencies and non-government organizations are involved with the permitting, monitoring and control of the discharged water. Minera Yanacocha maintains a relationship with 65 villages and communities, with a population of approximately 29,000 people and the city of Cajamarca with approximately 100,000 residents. This paper provides a high level review of the system complexity, the water balance, the excess water treatment facilities and social aspects of solution management.

Jan 1, 2004

By R. Church

The southern Powder River Basin (PRB) of Wyoming has developed into the largest coal producing region in the United States in the relatively short time span of 22 years. Since the opening of the first non-captive mine in the Basin in October 1972, truck/shovel fleets have played a major part in this rapid growth. In 1994, more than 200 trucks and 50 shovels will be used at 14 mines to help produce more than 190 Mt (210 million st) of coal in the southern PRB. This article presents an overview of the truck/ shovel operations in the Basin. Fleet sizes are reviewed, applications discussed, operating considerations explored, factors looked at that drive high capacity and restrictions listed for future growth. Fleet size Various sizes of trucks and shovels can be found in the southern PRB. However, a clear trend of increasingly larger size units is being established as producers attempt to remain competitive and productive.

Jan 1, 1994

By Owen Kreilis

By the time coal was discovered in Newcastle, Australia in 1791, it was already a most important industrial commodity in European countries. Coal was the first mineral to be discovered in Australia and the first to be mined. Today, coal remains Australia's most important mineral in terms of local use and international trade. The first mechanized longwall in Australia began operation in 1963. It contained self-advancing hydraulic supports and was installed at Coalcliff Colliery, located in the Southern Coalfields of New South Wales. After nine months and production of 53 kt (58,000 st), the unit was withdrawn, largely because of uncontrollable roof weight and with the problems of airborne dust and large coal still unsolved. Basically, roof support was insufficient. The European design of the Coalcliff longwall was inadequate for Australian conditions. Another type of support with modifications was installed and began operation at Kemira Colliery at Wollongong, New South Wales, in 1964.

Jan 1, 1995

By Bernie W. Martin, Paul MacLeod

The new St. Clair River International Tunnel Project presented unique challenges in planning, permitting and approval. The project straddles the border between the Province of Ontario and the State of Michigan necessitating the review of U.S. approval legislation that has not been used in 60 years. The preparation of an environmental impact report to satisfy the legislative requirements for the Federal laws of the U.S. and Canada as well as the Province of Ontario and the State of Michigan presented a daunting task. In all, over 200 external contacts were made in carrying out the environmental approvals and permitting work. The definition of the alternatives including the NULL option were documented along with the impacts and mitigation measures. A "Modified Delphi" technique, along with other methodologies, was used for alternative evaluation and selection. A formal and informal public consultation process was undertaken which involved over forty major presentations and external meetings. A unique alternative to the traditional design, tender, build contracting practice was adopted; The Negotiated Compressed Process (NCP).

Jan 1, 1993

By V. Saltas

In the present work, dielectric spectroscopy experiments were conducted on bentonite samples collected from Milos Island, in order to study their electrokinetic behavior in correlation with water content and mild heat treatment. Low-frequency dielectric spectroscopy has proved to be a power tool in the study of the electrical behavior of clay-water systems, because polarization and relaxation processes typically affect response at frequencies below 100 kHz. Therefore, dielectric and conductivity measurements in the frequency range of 10mHz to 1MHz were carried out by means of a high-resolution broadband spectrometer on bentonite samples, at various levels of hydration. The evolution of dielectric response was also examined after annealing of the samples. Experimental data were computer fitted with the empirical Havrilliak?Negami dielectric relaxation function on which a conductivity term was superimposed. The evaluated parameters of the fitting function are shown to be strongly affected by the water content of the measured samples.

Jan 1, 2006

By J. Nelsen

Social License to Operate continues to emerge as a paradigm fundamental to sustainable mineral resources development. It relates to a set of concepts, values, tools, and best practices that represent the view of reality held by each participant (industry and stakeholders). It enables a forum for negotiation through which all parties involved are heard, understood and respected. The exploration phase of the mine life cycle is generally the initial contact with local communities and forms the cornerstone for effective communication and trust building. This paper presents the development of a mineral exploration template, based on field studies, aimed at assisting exploration personnel to establish effective communications and engagement with local communities within a process to build a Social License. The template aims to provide practical assistance in conducting situational analysis - a process of examining and mapping a situation, its elements and their relations - in order to acquire knowledge and understanding of a project, locale and region. Situational analysis is the ?full situation of inquiry?, going beyond just ?knowing the subject? to being fully situated. It forms the initial foundation for a planning process presented in the paper that prepares for a strategy of initial engagement and consultation.

Jan 1, 2007

By P. Christmann

The operational paradigm of mining industries is shifting from ?optimal profit for the financial stakeholders? to a new concept compatible with sustainable development ethics: ?maximize economic and social returns at the local, national and global levels, while avoiding negative environmental impacts?. The number of stakeholders concerned by mining companies has grown significantly over the last few decades, and the role of local communities and civil society is now acknowledged by the mining companies adhering to the sustainable development ethics. ?Involve me? is becoming a key to maximize the returns the mining industry can provide to sustainable development. As the world?s major importer of many mineral commodities, several coming from developing countries facing severe short-term problems, the European Union (EU) is an important stakeholder and has a responsibility in supporting actions to strengthen corporate and public governance capacities. The purpose of this paper is to highlight the drivers leading to the development of sustainability indicators and to propose, within the 6th European Framework Programme for Research, Technological Development and Demonstration Activities (FP6), an European-level initiative to develop sustainability indicators adapted to the mining industry and its population with relevant data.

Jan 1, 2003

By J. Loredo

The Asturian Central Coal Basin, in northern Spain, has been from 18th century an important coal producing area in Spain. Previously to mining activity, aquifer systems were of multibed porous type but the secondary porosity induced by mining operations and constituted by mine voids and fracturing modified the aquifer systems to karstic-porous type. The pumping stop associated with mine closure processes results in the flooding of the mining works. This causes important modifications in the hydrogeology and the hydrology as well as in water flow and in water quality. As a consequence of mine flooding, water overflows through shafts and old galleries or through not controlled ways of water leak to surface. Water tends to recover the original piezometric level, but materials significantly modified by the mining activity behave differently in terms of hydrogeology, and thus, the recuperation of the water level can affect infrastructures and housing in the area of the mine. When pumping stops, the quality of water can also be seriously affected when water comes in contact in oxidant conditions with sulphides and sulphates present in the surface of the materials that are flooded, especially in the subsequent period immediately after pumping stop.

Jan 1, 2006

By C. W. Schultz

Introduction The Mineral Resources Institute, The University of Alabama, has for the past three years been engaged in a program to develop a beneficiation system for eastern (Devonian) oil shales. One objective of that program was to evaluate advanced technologies for effecting a kerogen-mineral matter separation. Column flotation was among the advanced technologies selected for evaluation. Early in the program it was shown that column flotation was superior to conventional (mechanical) flotation and to the other advanced technologies being evaluated. The investigation then proceeded toward the further objective of defining the optimum operating conditions for column flotation. One observation made in the course of optimization testing was that introducing the feed into the froth (above the pulp-froth interface) resulted in an improved combination of concentrate grade and kerogen recovery. This observation was reported in a previous paper (Schultz and Bates, 1989). Because the practice of maintaining the pulp froth interface below the feed point is contrary to "conventional" practice, it was decided to subject the observation to a systematic series of tests. This paper describes a recent series of tests and the results that were obtained.

Jan 1, 1991

By C. Sachanidis

From the surface mines of Ptolemais basin 48 samples of Pliocene lignite were collected. The samples were analysed using Instrumental Neutron Activation Analysis (INNA) and Inductively Coupled Plasma (ICP) for determining the concentrations of 39 trace elements. The contents of sulphur and ash and the loss of ignition were also determined. The chemical affinity of these trace elements was estimated based on 40 correlation diagrams between the elements concentrations and the ash content of the collected lignite samples. According to the obtained results, 18 elements have inorganic affinity (Co, Cr, Cs, Hf, Sc, Th, La, Ce, Nd, Sm, Eu, Yb, Lu, ?n, Ba, ?, Sn, ?r) and 10 elements have inter-mediate affinity (As, U, ?r, Pb, Cu, Sb, Sr, S, Ni, V). The remaining 12 elements (Au, Ir, ??, Rb, Se, Ta, W, Tb, Ag, Cd, Bi, Be) exhibited concentrations below the detection limit. Thus, they were impossible to be classified in a specific affinity group. Based on the classification of these trace elements and sulphur in inorganic and intermediate affinity groups some useful conclusions are drawn regarding their behaviour during lignite combustion and lignite ash utilization and disposal processes.

Jan 1, 2006

By Antonio Peralta

Mining activity in Mexico began in the 16th century when the Spanish realized the mining potential of the new territory. Since that time, mining has evolved into a strong and vital industry for the country. Good professionals in the mining-related fields are fundamental to the growth and improvement of this industry. Since the end of the 18th century, formal education in mining has been available at the University of Guanajuato, in Guanajuato, Mexico. This school created one of the first schools of mines on the North American continent in 1828. In recent times, some other programs have been created at other universities. Universities offering mining related programs Listed here are the seven universities in Mexico that offer mining related degrees. They are the University of Guanajuato, UNAM, the University of Zacatecas, the University of Chihuahua, the University of Sonora, the University of Coahuila and the University of San Luis Potosi. The University of Guanajuato is the only Mexican university that offers graduate studies at the master's level. No PhD programs in mining engineering are offered at any Mexican university. Programs at each university are of different duration. They are: • University of Guanajuato-Five-and-a-half years, divided into five years of classroom instruction and six months in the working place. • University of Zacatecas - Five years of classroom instruction.

Jan 1, 1994

By N. ?peh

The purpose of the paper is to present a way of assessing nonrenewable lignite resources by means of sustainability indicators. An introductory presentation of the origin and characteristics of the discussed nonrenewable natural resources is followed by the study and analysis of separate sustainability indicators. Out of many, only the ones that would directly relate to the explored coal deposit were studied. Some different viewpoints such as economic, social and environmental were assessed inside the studied landscape structure and in relation to other provincial resources using the indicators that are closely linked with the explored lignite reserves. Exploitation of coal as an underground nonrenewable natural resource, has been taking place in the ?alek valley for more than 120 years. However, about 60% of the coal will still be left underground since not all coal will have been extracted when the mine closes. According to the regional and wider national strategic goals concerning the use of natural resources and electricity production in the future, the sustainable aspect of the exploitation of the geologically well explored reserves is emphasized in the paper. Finally, we have tried to evaluate the role and the meaning of the studied underground natural resources for further sustainable development of the ?alek valley and placed stress on the most questionable spheres that should be considered preferentially.

Jan 1, 2007

By S. G. McDowell

Automation techniques are used during the design stage of continuous miners to decrease the time required and ensure the accuracy of the design. This is followed by automated manufacturing processes to reduce manufacturing time and improve the quality and consistency of parts. Combined, the result is a more reliable machine that can provide ongoing production capability. With the use of automation to enhance operator effectiveness and monitor machine condition, the productivity of machines is also improved. Productivity of continuous miners doubled over a 10-year span (Fig. 1). Although this article focuses on the continuous miner, it should be recognized that production increases of the continuous miner would not be realized without increased capabilities throughout the rest of the mining system. There are several aspects of automation that have played a role in providing increased continuous miner productivity. Though some are considered indirect, they still had significant influence on the overall result. Basically, productivity increases are obtained by cutting, loading and transporting the coal at a maximum rate. In addition, these tasks must be consistent, with minimal downtime. Therefore, the miner had to improve in operational capability and reliability. Automation techniques used during machine design, manufacturing and operation have all played significant roles in achieving higher productivity.

Jan 1, 1991

By J. Partyka, J. S. Stachulak

Dust produced during blasting in a copper/nickel based mine was studied and characterized. A stope utilizing the crater blasting technique, or the vertical retreat mining (VRM method), was examined. Two dust monitors were used to measure an airborne dust produced during blasting operations. The data collected in situ was primarily used to formulate the boundary value problem for a generalized equation that describes the transportation process of airborne dust from all places where dust is produced by the VRM mining method. The field data was also used to define the analytical forms for the initial and boundary conditions, to provide a simple and reliable equation for flow of dust in a stope vicinity, and to identify the non-measurable constants. The effects of the amount of blasting material and of the ventilation system in use on dust concentration are also discussed.

Jan 1, 1995

By Campbell J. McKenzie

Following on from the successful completion of three exploration programs and the discovery of two new inactive Seafloor Massive Sulphide (SMS) deposits within New Zealand?s Exclusive Economic Zone (EEZ), Neptune is now poised to take the next step from explorer to developer. Neptune considers that commercialization of SMS deposits represents the future of the mining industry, providing a new source of metals to the world economy, and enabling host countries to benefit from this new industry. Neptune recognizes that marine biodiversity is among the greatest treasures of New Zealand. The geological isolation, range and complexity of habitats, and a number of major ocean currents that influence New Zealand have created diverse marine communities. Neptune, recognizing both the environmental importance of marine biodiversity and the value it provides to all New Zealanders has made commitments to ensure sustainable development. There are many unanswered questions regarding how the marine environment may be affected by SMS development, however best practice environmental management is a key aspect of the Company?s approach to our activities and the code for ?Environmental Management of Marine Mining? prepared by the IMMS has played a part in this approach. Neptune has close relationships with the scientific community to ensure that appropriate environmental strategies and plans are developed in order to minimize the effects of our activities on the environment.

Jan 1, 2008

By S. K. Kawatra, T. C. Eisele

To reduce their sulfur emissions, many coal-fired electric power plants use wet flue-gas scrubbers. These scrubbers convert sulfur oxides into solid sulfate and sulfite sludge, which must then be disposed of. Currently, the major markets for scrubber sludge are for manufacture of gypsum products, such as wallboard and plaster, and for cement. However, the quality of the raw sludge is often not high enough or consistent enough to satisfy manufacturers, and so the material is difficult to sell. Other markets, such as paper manufacture and plastics fillers, have even more stringent quality requirements and will not accept raw sludge at all. In the work described in this paper, several reagents have been examined to determine their ability to selectively improve the flotation of the unreacted limestone contaminant away from the desirable products (calcium sulfite and gypsum). The most success has been achieved using a cationic collector, which shows a higher selectivity between calcium sulfite and calcium carbonate than do the anionic collectors that were studied.

Jan 1, 1995