Search Documents

By Jin Kim, Jerry C. Tien

Water is still the most economical and popular means of controlling dust underground. It is a process that captures dust by bringing water droplets into intimate contact with coal particles. Wetting agents, also known as surfactants, can be added to greatly facilitate such a process since they tend to reduce the interfacial tension between the coal particles (usually hydrophobic) and the liquid. The surfactants used in the study were first chosen on the basis of their HLB (Hydrophile-Lipophile Balance) value, and later tested in order to select the right type and amount of surfactants to give the best performance. Both static and dynamic tests were later conducted using different types of surfactants to examine their respective wetting effectiveness on coal particles. Experimental results show close correlation with the theoretically calculated collection efficiency that is based on a horizontal tunnel and a solid-cone water spray.

Jan 1, 1993

By D. R. Baughman

Copper oxide deposits that may be considered for in situ leaching exist in unique geologic settings, different from uranium deposits. A large number of interrelated factors must be considered in wellfield design. Many of these factors are hard to quantify and are directly related to geologic features of the orebody. This paper discusses some of the important factors in wellfield design and suggests an outline for a design procedure.

Jan 1, 1988

By Ingo Ossenbühl, Wolfgang Dolsak, Vojtech Gall, Axel G. Nitschke

"Yielding support systems for application in underground construction have a long history, primarily in mining. Typical examples are tunnels subject to loading conditions that lead to overstressing of the newly installed support or existing tunnel structures in active fault zones. Recent applications for tunnel rehabilitation projects unveiled the capabilities and flexibility of combined yielding support systems presented in this paper. Frequently, the main requirements for tunnel rehabilitation applications are a fast, safe, and simple installation along with the need for flexibility with regards to existing tunnel geometries. A combined support system consisting of steel sets with yielding connections and special groutable hoses has proven to be an efficient support measure providing a multitude of advantages compared to conventional rehabilitation approaches. The presented yielding support system provides an immediate and active support, while it allows for controlled yielding upon experiencing loads beyond its support capacity. INTRODUCTION The excavation of underground spaces leads to redistribution in the existing stress regime. This load redistribution goes along with deformations in the surrounding rock mass. Magnitude and duration of these deformations depend on the tunnel’s depth and geological conditions, but also on the installed support system. Modern civil tunneling infrastructure has generally an envisioned service life of about 120 years. Conventional tunneling provides typically a dual support system, split into the initial (or primary) and final (or secondary) lining. A typical design principle in civil tunneling is to let the vast majority of deformations acting on the initial lining cease, before the final lining is installed. Based on this approach, the loading on the final lining is significantly reduced and signs of overstressing, such as cracking of the lining, are typically limited to the initial lining. However, special cases in swelling and squeezing ground require different approaches, including yielding support systems."

Jan 1, 2016

By H. Ouellet, J. Paraszczak

The pneumatic jackleg drill remains a widely used tool in development and production drilling in many small-scale and narrow-vein underground mining operations in North America. Several drawbacks of this technology (unsatisfactory drilling rate, noise, vibration, presence of oil mist, etc.) and the successful introduction of water-powered jackleg drills in South Africa have stimulated the interest of many mine operators. The performance of both drill types have been tested in a mine site in Northwestern Quebec, Canada. Results of the testing of penetration and advance rates as well as environmental aspects are presented. They show a superiority of water-powered drills, even though the difference in performance is less significant than that reported from South Africa. Further research avenues are proposed to better evaluate the potential of water drilling technology in North American metal mines.

Jan 1, 1995

By Jr. Mason

Eminent Domain is the power of the government or municipality to take property for public use without the consent or acceptance of the owner. Typically the agency taking the property will make an offer on the property, hoping that the owner will immediately accept and allow work to begin. If a mutual resolution regarding the property value cannot be reached, however, the municipality will condemn the premises and institute a condemnation action in a court of law, which is when the problems begin. The power of the government to take the subject property is limited by the Federal and State constitutional duty to pay "just compensation" for the property.

Jan 1, 1989

By S. Horton, F. L. Stanley, P. J. Bethell

Introduction The McClure River Processing Plant is located at McClure in Dickenson County, VA. The plant was originally constructed in 1979 as a 600 st per hour facility. The plant is fed by coals from numerous mines in the area as well as a major longwall mine onsite. Coal is processed predominantly for the metallurgical coal market. The original plant was comprised of three separate processing circuits incorporating a heavy medium vessel for the coarse material (+10 mm). Intermediate sized material (10 x 0.6 mm) was beneficiated in heavy medium cyclones, with the remaining fines (0.6 mm x 0) passing to froth flotation for upgrading. The products from all three circuits were combined prior to thermal drying and then stored in silos or ground storage prior to shipment to the metallurgical coal markets. A middlings heavy medium cyclone circuit was also present to rewash the vessel and primary heavy medium cyclone rejects. The original circuit is as shown as Fig. 1 (Editor's note: All figures are reproduced at the end of this paper.) In reasonably close proximity to the McClure Plant is the much older, less efficient Moss 1 Plant, (Chance cone, table, water only cyclone, froth flotation, Fig. 2), which prior to the McClure Plant expansion was processing considerable tonnages of coal. At that time, the McClure River Plant was processing coal at the maximum possible feed rate, and the Moss 1 Plant was finding increasing difficulty in maintaining the stringent quality specifications on its major metallurgical coal accounts. Given the fact that many of the feeder coals to Moss 1 could be moved with minimal difficulty and cost to McClure, an exercise was conducted to evaluate the potential of expanding the McClure Plant. This would result in transferring coals from Moss 1, thereby increasing yield, reducing operating costs, and enabling customer specifications to be met more easily. After evaluating many possible ways of expanding the McClure Plant, we eventually settled on an approach based on the idea of Gallagher at German Creek in Australia (Gallagher, 1986). Our objective was to increase plant capacity by removing the coarser size fractions (0.60 x 0.15 mm) from froth flotation and at the same time eliminating the finer fractions (1.25 x 0.6 mm) from the heavy medium cyclone circuit, thereby allowing these circuits and therefore the plant as a whole to increase its capacity. These size fractions (0.60 x 0.15 mm from froth flotation and 1.25 x 0.6 mm from the heavy medium cyclone circuit) would be treated in a new spiral circuit. After desired evaluation of the various circuit capacities, including desliming screen, clean coal filter and thermal dryer capacities, etc., it was concluded that we should be able to maintain high levels of processing efficiency in the existing circuitry while at the same time expanding plant feed rate from a nominal 600 st per hour to 1000 st per hour, thereby achieving the objectives The circuit that was finally settled on is shown in Fig. 2. Several unique features were incorporated in this circuit in an attempt to maximize processing efficiency and reduce maintenance costs. First, the idea of a single-stage spiral circuit was abandoned in favor of a two-stage circuit incorporating rewashing the primary spiral middlings in a secondary spiral (Bethell, 88). The spirals selected were Mineral Deposits Model LD4 units. It was felt, after much previous testing, that spiral middlings rather than being a true middling gravity fraction were in fact a combination of true middlings with a preponderance of misplaced light coal and high-density rock. Consequently the insertion of this material directly into either clean coal or refuse streams (per normal practice) would only lead to loss of efficiency. The operating philosophy behind the design of the circuit was to produce the purest coal and rejects possible by adjusting the spiral splitters. Misplacement of refuse into the clean coal and vice versa would be minimized by taking a fairly large middlings cut. By reprocessing this material (10%-15% of primary spiral feed) in a secondary bank of spirals the misplaced material in the primary middlings would be reprocessed and its probability of reporting to the correct stream greatly enhanced. To minimize fines loading on the spirals, fine aperture sieve bends were to be included. A further novel feature of the circuitry is the desliming/ dewatering system. A philosophy of accepting inefficiency but forcing it to work in our favor was developed. The dewatering screens (Linatex Combis) were chosen not for their ultimate screening efficiency but for their ability to remove slimes (tolerating a fair quantity of oversize in the effluent) and their enhanced maintenance characteristics. Any oversize passing into the effluent, together with the fine coal centrifuge effluent, would pass to classifying cyclones, the objective of which was to reject to overflow (and hence froth flotation) as many fines as possible (-150 µm) without running the risk of losing coarse (1.25 x 0.15 mm) material to oversize. Hence, by a process of producing a "slime free" screen product coupled with a "coarse free" cyclone overflow, sizing efficiency could be maximized. Obviously, recirculating load had to be factored into the Combi Screen design capacity. The spiral circuit as shown in Fig. 2 was installed at McClure River in January 1988. The spiral circuit efficiency was very high immediately, and, after the normal debugging, plant capacity has been increased to the point at which we are currently processing of the order of 1100 st per hour. Test program The performance of the spiral circuit has been evaluated by two major samplings of the entire new circuit, coupled with routine bi-monthly tests on all other major components of the plant circuitry.

Jan 1, 1992

By Jianping Sheng, Francis Otuonye

The potential for methane and coal dust explosions in underground coal mining operations has increased in recent years with the introduction of fast coal-cutting machines. Dust explosions usually follow accidental ignition of a methane pocket. The dynamics of the explosion may be strong enough to pick up and disperse coal dust deposited on mine surfaces and ignite the mixture. A self-sustaining dust explosion can then develop and propagate at large distances. Ignition of dusts can result in a fire, and this may also lead to a dust explosion if the burning dust becomes airborne. Entrainment of dust and the resulting dust concentration in the gas stream are some factors which determine the features of the subsequent explosion and flame propagation. A model of coal dust transport in the gas stream due to the initial explosion is presented. In this model, equations for the conservation of mass, momentum and energy are coupled with the convective-diffusive model of dust transport. The system of equations is solved numerically to obtain dust concentration, convective velocity and gas pressure profiles.

Jan 1, 1989

By H. Polat, B. Mohal, S. Chander

Several nonionic surfactants and one anionic surfactant were tested to enhance the flotation response of a low-rank coal. The nonionic surfactants included an ethoxylated octylphenol and several polypropylene-polyethylene block copolymers, and the anionic surfactant was a dioctyl sulfosuccinate. All of the surfactants improved the yield significantly, but the influence on grade was complex. To elucidate the mechanisms involved, separate studies were conducted to determine the emulsification behavior of the surfactants. For the nonionic water soluble reagents, a correlation between the emulsifying power of the surfactant and the flotation response was observed. An increase in the number of droplets produced was considered to he the main reason for increases in the yield. However, a small amount of surfactant adsorption on coal is essential to promote adhesion of oil droplets. When the surfactant was introduced into the flotation pulp prior to addition of dodecane, the benefits of the surfactant decreased significantly. The decrease was attributed to both a decrease in hydrophobicity of coal through increased surfactant adsorption and a decrease in the surfactant available for emulsification. When a surfactant dispersed in oil was used, the transfer of surfactant to the aqueous phase was minimal, and a considerable increase in yield was observed.

Jan 1, 1995

By D. A. Rice

As part of a cooperative effort between the U.S. Bureau of Mines and the Florida Institute of Phosphate Research (FIPR), with input-from the phosphate industry, the conversion of phosphor-gypsum to sulfur is being investigated. The proposed process incorporates a thermal reduction of phosphogypsum to calcium sulfide (CaS) and a hydrometallurgical treatment to convert calcium sulfide to ammonium bisulfide (NH4SH), which is then oxidized using a catalyst to produce elemental sulfur. The paper summarizes the results of continuing laboratory studies using an activated carbon catalyst which was loaded with sulfur through oxidation of ammonium bisulfide solution. The extraction of the sulfur that forms in situ on the catalyst is a key area in the development of the sulfur recovery process. Two approaches for removing the sulfur are being investigated: 1) thermal treatment to volatilize sulfur, and 2) leaching the sulfur using liquid anhydrous ammonia. The research has shown that it is technically feasible to recover over 90% of the sulfur from the carbon by either volatilization or ammonia leaching. Locked-cycle testing has demonstrated that the carbon has the potential to be recycled after ammonia leaching.

Jan 1, 1988

By Zbigniew Pokryszka, Eric Saraux, Christian Tauziède, André Carrau

This paper presents recent developments in the use of a CFD model for representing the flow of gases in the goaf of retreat faces. In France, it is of highest importance to optimize firedamp drainage in very gassy mines and nitrogen injection in faces prone to spontaneous combustion. Numerical modeling has been used to solve this problem. So the model developed has been first calibrated using a large quantity of field data and could then be used for various simulations. Though still in progress, this research has given promising results, many of them being already set into practice.

Jan 1, 1997

By C. I. Huang

The mining industry is an easy target for criticism from an environmentally sensitive society. Recent researches discovered that human activities, including mining. cannot be blamed for all of the pollution observed on earth. Interdisciplinary research is providing diagnostic and remedial solutions to problems such as acid mine drainage and cyanide-polluted streams. Researchers have also found that mercury-bearing hot springs and volcanic eruptions are partly responsible for some pollution. Geochemists, mining geologists, engineers, and environmental scientists can pool their efforts to make the environment cleaner and safer. Remote sensing of the environment and the use of microbes may become much more popular in the near future in the mining-environment arena.

Jan 1, 1988

By W. R. Hopkins

Over 95 percent of the world's refined copper is now produced by electrolytic processes. The bulk of this electrolytic copper comes via the conventional route for sulfide ores of concentration, smelting and electro-refining. A rapidly increasing percentage of world production is now achieved using hydrometallurgical routes involving dissolution of the copper values from minerals, purification of the resultant leach solution by solvent extraction and finally deposition as cathodes by electrowinning. The technology can now be considered mature and this paper endeavors to summarize recent developments which, from the authors' perspectives, are important.

Jan 1, 1989

By J. W. Leonard

Breakage, handling and treatment techniques that result in the placement of greater quantities of coal in fixed volume haulage units such as ships, railroad cars, trucks, mine cars, shuttle cars and scoops can do much to increase productivity by improving bulk density to reduce delivered cost, surprisingly enough, only in steel industry by-product coking has this subject been investigated and applied to practice, where as much as 20% or more productivity has been achieved. Research at UK Mining using popular coal mine loading cycle simulators shows that for typical Central Appalachian mining conditions a 10 to 20 percent gain in bulk density can produce a 15 to 30 percent increase in the loading cycle time of fixed volume shuttle-car/scoop based mining systems.

Jan 1, 1989

By T. Rockley, B. Goertz, S. McDaniel, J. Brune, K. Bakhsh

"Researchers at the Colorado School of Mines, under a project funded by the Alpha Foundation, have developed a working prototype of a dust sample collection device designed to determine if sufficient rock dust has been placed in an underground coal mine to prevent coal dust explosions. When used in conjunction with the Coal Dust Explosibility Meter (CDEM), the device will provide near instantaneous results on the quality of rock dusting at the tested location. The sampling device applies a pulse of air to a testing surface and collect a representative sample of mine dust based on the pneumatic entrainment process during a mine explosion. The use of both physical testing and Computational Fluid Dynamics (CFD) modeling has allowed researchers to refine the design to accurately represent the particle entrainment and optimize the sample size collected for the CDEM. The prototype is being tested in a mine environment to produce information of usability and practical aspects of mine dust sampling. This paper is a progress report summarizing the current status of sampler development. Researchers expect to have a fully developed and tested sampler in early 2016. INTRODUCTION Underground coal mines face the danger of methane and coal dust explosions. The disaster at Upper Big Branch mine (2010) has demonstrated the impact of a violent coal dust explosion that fatally injured 29 miners. Reviewing the history of coal dust explosions, researchers found that that mine operators and mine inspectors do not have a reliable method of collecting dust samples to assure that sufficient amounts of rock dust have been places to inertize the coal dust. This is a problem specifically with small mines that do not have dedicated safety departments to track rock dusting work. The aim of this research is to develop a simple, portable device that can help underground mine examiners collect dust samples from workings and test the explosibility of the sample near instantaneously. Researchers determined that the current brush-and-pan sampling method required by MSHA (MSHA 2013) is flawed in several aspects: Mechanical sampling with a brush exerts forces on the mine dust that may differ significantly from those present during an explosion. Also, U.S Bureau of Mines research (Nagy 1965) has determined that only the top 0.125 inches of the mine dust layer will be entrained in a coal dust explosion. Using a handheld pan and brush, it is difficult to correctly and repeatably sample a layer of this exact thickness. The following will describe the CFD modeling and experimental testing for the development of the prototype sampler. Researchers analyze the accuracy and performance of the prototype during the course of the build process."

Jan 1, 2015

By M. E. Gershon

Software for coal blending has gained a lot of recent attention as micro-computer programs have come on the market. Some of this software is appropriate and some is not. This paper looks at the types of models being used and points out the strengths and weaknesses of each. Recommendations are then made concerning the level of detail required for these programs, relating this concern to the various ways in which coal companies are using these programs. A checklist of company requirements for these programs and available pro-gram-features provides an aid in matching the program to the company.

Jan 1, 1988

By Ignazio Carbone

"During the design of a typical modern subway, engineering aspects prevail since underground structures remain hidden to most humans. Aligning the advanced architectural concepts with the engineering requirements of the Naples Metro Line 1 (Italy) called for a thorough rethinking of the design process so that the engineering could be kept aligned with the architecture, integrating seamlessly the two with the construction methods, standards and technology.The preliminary design process consisted of three major phases: •,geotechnical and geological issues, preselection of construction methods; •,functional scenario based on engineering and construction requirements; •,review and merging of the architectural concept with the functional and engineering aspects. The last phase proved the most demanding one, matching the first outline sketches with the applicable construction methods. This required continuous alignment of approaches, eventually leading to the design consistent with the original architectural vision, yet fully compliant with the engineering and construction framework. At the beginning general information on Line 1 will be provided, followed by some main features of the construction work along the Dante – Garibaldi section both for the tunnel and the stations. At the end, the selected methodology and the related consequences on the functional, technical and architectural design will be outlined.City of Naples current municipal transportation plan envisages a circle ring line for the metro line M1. Actually it’s open to public the segment Piscinola – Dante – Garibaldi run by AMM, municipal company. This ring segment has been built by Metropolitana di Napoli, while Napoli Metro Engineering (company belonging to MMspa Group) is in charge for the planning of entire system and construction management. Line 1 connects Piscinola-Secondigliano northern periphery to Vomero shopping neighborhood, downtown and Central Railway Station."

Jan 1, 2016

Adequate ventilation of coal mine working faces is the single most important technique for controlling respirable dust and methane. Choosing the right technique presents some tough questions. Bureau research has shown that to control respirable dust you must contain the dust near the face, keeping rollback (turbulence) to a minimum. For methane the most effective approach has been to use a blowing brattice or tubing and to create turbulence and disperse the face methane, allowing it to pass over the machine and into the return. It is immediately apparent that the two approaches may counteract one another, thus complicating the decision as to which system may be best for a given situation. At present, Bureau research has developed two successful machine-mounted face ventilation systems to meet these different needs and allow deeper cutting. The fan-powered dust scrubber is designed to control dust primarily associated with blowing face ventilation systems. The spray fan controls methane on exhaust-ventilated sections.

Jan 1, 1988

By E. Poeck, R. Garvey, U. Ozbay, K. Zhang

"A coal bump is characterized by the sudden failure of one or more pillars and an associated release of kinetic energy. Although the geologic conditions surrounding coal bumps are often similar, their occurrence and magnitude are difficult to predict. This paper presents the development of an approach to assess the potential for coal bumps in room and pillar mines through the use of energy concepts and special consideration of the interface properties between the coal and overlying rock. Back analyses were performed on the widespread collapse of a room and pillar mine with an associated 3.9 local magnitude seismic event. Pillar and mine-scale models were constructed using the distinct element method to simulate the mining stages leading up to the collapse. A variety of loading conditions, material properties, and interface properties were evaluated for their effect on unstable failure of single pillars, and the mine-scale model was used to study the evolution of failure during progressive mining. The extent of unstable failure was quantified in these models by calculating the total kinetic energy released during each mining stage. Through the parametric analysis of single pillar models, it was found that softening parameters in either the coal or the coal/rock interface can individually facilitate unstable failure of pillars, but the combination of the two in a single model produced a much higher release of energy during failure. The results of the mine-scale model further illustrated the trend as the combination of softening parameters in the coal and coal/rock interface produced a series of failures which most accurately reflected the collapse event at the mine. The method of room and pillar stability analysis demonstrated in this study effectively explores the potential for large coal bumps. INTRODUCTION The analysis of coal pillar behavior is challenging because natural variability in geologic conditions requires estimation of material strengths and predicted loads for a given mining situation. Large width-to-height (w/h) ratio pillars and deep overburden present an additional challenge, as the failure behavior of such pillars is more complex and may involve unstable, sudden collapse. Empirical methods have improved the success of coal pillar design for a wide range of conditions, but for deep cover and squat pillar geometries, less accuracy has been achieved in predicting pillar performance (Mark 2000). As with any empirical approach, more back analysis and the consideration of new variables may help improve understanding and accuracy of future designs. This paper presents a study of pillar stability through the back analysis of the Crandall Canyon Mine collapse, which occurred in August of 2007. Pillar-scale models are utilized for the calibration of material properties and assessment of potential instability under varying conditions, and mine-scale models are constructed in an attempt to reproduce widespread failure and correlate with observations at the mine. Special consideration is given to the properties of the coal and the coal/rock interface, and kinetic energy is calculated throughout the course of the simulations to gauge the level of instability when pillar failure occurs. Models were constructed using the Universal Distinct Element Code (UDEC) (Itasca, 2014)."

Jan 1, 2016

By R. S. Scheetz

The search for a more effective means of coping with methane liberation has resulted in the expanded use of seam degasification. Its advantages are measured not only in reducing the hazards due to methane, but also in producing a marketable commodity: .the gas, itself. However, the success of a methane drainage system is the culmination of many complex factors, the most important being the coal seam permeability. The two most popular drainage techniques used mining today are the vertically simulated borehole method and the in-seam horizontal borehole method. The objective of this paper is to determine the permeability range in which the selection of the degasification technique is based primarily on equipment and economic analysis. A discussion of the equipment involved will be incorporated into examples evaluated by the Penn State coal methane simulation model.

Jan 1, 1989

By R. R. Rollins

Conventional methods of controlling abandoned mine fires include: loading out, inundation, fire barriers, flushing, and surface sealing. This paper describes a proposed fire-control technique utilizing a new explosive fragmentation method. An impervious barrier is created by using explosive energy and strategic emplacement in boreholes drilled from the surface. Blast round design, average fragment size, and impermeability of the fragmentation barrier are discussed. This barrier, created by the blasted floor rock, could also be used to fill in the open space in abandoned mines for subsidence prevention or control.

Jan 1, 1989