Search Documents

By Peter Zhang, Daniel Su

Following the first longwall excavation at a deep-cover gas well site, the pre-mining modeling prediction of longwallinduced casing deformations in the fully cemented production casing were in excellent agreement with post-mining Caliper survey results. However, after second panel mining, the post-mining Caliper survey revealed a large plastic deformation near the top of the Pittsburgh Seam. The focus of this paper is to identify the possible cause of such an anomalous deformation. Very high longwall-induced casing stress near a thick claystone layer at 23 feet above the Pittsburgh seam horizon was identified as the primary cause. Leaving the production casing uncemented or using softer cementing material between intermediate and production casings is identified as the best practice.

Feb 1, 2024

By N. S. Tombs

This paper presents the experimental results of an ongoing investigation into various properties related to the performance and durability of concretes made using existing and new cement replacements. The process of cement and concrete production is investigated focusing on product performance and environmental performance. The overriding factor for the progression of a material will be product performance however; each material selected will have many intrinsic environmental benefits. The study combines Ordinary Portland Cement (OPC) with each cement replacement candidate using the most common replacement percentages, 10, 20, 25, 30 and 50 percent. A 35N/mm2 concrete is then prepared and analysed in the fresh and hardened state. In addition, a chemical and physical analysis of each replacement material has been performed and results compared to the control samples containing OPC only and Ground Granulated Blast Furnace Slag (GGBS) as a replacement. The results show that in their present form the replacements used in this research do not compare with the strengths achieved by the controls. The right balance of chemical composition and particle grading needs to be achieved to produce a realistic replacement material. The processes required to achieve this must strike a balance between monetary and environmental cost.

Jan 1, 2006

By V Leus, J. Kallioinen

The large size of the modern flotation cells and the high product flow rate from them has increased the importance of optimal flotation of all the particle sizes and of process control. By treating all the subprocesses of flotation separately a new family of flotation cells and a new concept of optimizing the flotation of coarse and fine particles in separate units but in the same row of flotation cells has been developed. The paper discusses the possibility to enhance coarse particle flotation by varying the froth residence time. A function has been developed between the residence time of the froth, air rate and the froth removal rate of coarse apatite particles. The response of apatite flotation to different control variables has been studied and modelled. The results show that the BPL assay response depends not only on the control variable used but also on the feed assay to the cell. There exists an feed assay dependent region within which the froth assay can be controlled by using the froth residence time as the control variable. These regions can be used to tune a rougher-multistep cleaner circuit to optimal.

Jan 1, 1993

By George M. Potter

Precious gold and silver markets support substantial activity in the search for and development of improved and unconventional ore and tailing processing methods. The need for such methods 1s strengthened by consideration of increasingly low grade and refractory ores and old tailing reserves. As background for this review of new and unconventional precious metal processing, recent USBM data (1981) show annual world gold production of about 40.8 million troy ounces. In the U.S. about half the 2.8 million ounce consumption was used for jewelry and the arts, 39 percent for industry, and 8 percent for dental purposes. World silver production in 1981 was about 365 million ounces. Domestic usage the same year was about 117 million ounces. More than $ was used for photography and 30 percent for electrical and electronics. By process, about 1 percent of U.S. production of gold came from amalgamation, 66 percent from cyanidation, 31 percent from smelting ores and concentrates, and 2 percent from placers. As for silver, about 11 percent is from cyanidation and 89 percent from smelting ores and concentrates. Evidently the search for innovative and unconventional precious metal processes must include gravity concentration, froth flotation, hydrometallurgical, and electrometallurgical methods. Although smelting processes are equally important, they largely comprise nonferrous metal technology, and are not discussed here.

Jan 1, 1984

By R. A. Lohnes, S. M. Levorson

As part of research to develop a coal handleability index that predicts the ease with which coal will flow through a handling system, comparative tests were conducted with a Johanson Indicizer and a low-stress triaxial apparatus on 12 coals at a variety of gradations and moisture contents. The lndicizer test provides a rapid method for generating data associated with coal handling characteristics. The arching index measured with the Indicizer is a function of the geometry of the apparatus as well as the properties of the coal. The handleability index determined from triaxial data is a more direct measure of coal characteristics. The handleability index shows a wider range of values than the arching index and, therefore, appears to be more sensitive to coal variations. Neither the arching index nor the ratholing index, as measured with the Indicizer, agreed well with the handleability index. This is attributed to differences in sample preparation as well as to the tests themselves.

Jan 1, 1993

By W. M. Kidd

INTRODUCTION Uranium mine inspection in Canada forms one element of the enforcement of the Atomic Energy Control Act; it is under this Act that all Canadian uranium mines and mills are licensed to operate. Inspection duties are carried out by a small core staff of federal government inspectors (working for the Atomic Energy Control Board (AECB)) largely supplemented by provincial mine inspectors working on behalf of the AECB. Unlike most resource extraction in Canada, uranium mining is under federal jurisdiction and consequently it was the AECB who decided in 1975 that changes in the Canadian uranium mining industry, particularly its expansion and the expanding role of the mine inspector in the limiting of exposures, warranted the offering of a special radiation protection training course. The Uranium Mine Inspector Training Course (UMITC) was first conducted in 1976 at the Elliot Lake Centre in Elliot Lake, Ontario. Subscription for the course was not limited to mine inspectors to enable union stewards, management personnel and provincial/federal labour inspectors to attend. This paper will present an outline of the course content, the format of its presentation and non-curriculum aspects of running a course of this type in uranium-producing community. The core lecturers for UMITC are drawn from the Radiation Protection and Uranium Mine Divisions of the AECB. In addition, guest lecturers are invited from universities and medical research centres together with industry professionals and government researchers. In all some twenty-four plus presentations are made over the first five days of lectures. The program topic areas, hazards, controls, measurements, record-keeping and health effects are preceded by an intensive half-day session on radiation fundamentals. TOPICS Hazards [Dust] A review of the dynamics of airborne particles including the effects of particle size, gravity and wake-turbulence on the behaviour of dust clouds. Associated topics are migrational aspects of dust particles and specific dust-generating mine operations. [Radiation] Canadian uranium mines are increasingly diverse in nature ranging from large scale low-grade underground operations in Elliot Lake to smaller high-grade open pits in Saskatchewan. Papers are presented on assessments of internal and external exposure, the metabolic pathways of ingested or inhaled radiation and the specifics of mine and mill hazards. Radiation hazards are further broken down into gamma surveys of uranium mines, radon daughter concentrations and problem areas. Controls The relationship between mining methods and the operating environment is critically important to ensuring safe working conditions. This refers to both the selection of machinery/devices, etc., and to engineering controls which are instituted to remedy problems created by new technology. UMITC examines a number of possible mining techniques, their criteria for selection and impact on the working environment. Control measures, ventilation practices and design, the need for continuous water misting and special open-pit precautions are presented. These lectures frequently conclude with suggestions for better operating guidelines for mine ventilation systems and the need for greater co-operation between the ventilation department and the underground crews. Measurements Uranium mining regulations stress the need for a high standard of exposure monitoring, statistical planning and record-keeping. [Statistics] Although many course participants are well versed in statistics, certain fundamentals are repeated and include, the concepts of mean, variance, standard deviation and standard deviation of the mean. Confidence levels, decision-making based on sample statistics and statistical records are also discussed. [Dust Measurement] Dust measurement is particularly critical in the mines where the high silica content of the ore body, such as those at Elliot Lake, results in the continuous generation of dust. Sampling practices, filtration, impaction, thermal impaction and electrostatic precipitation are explained together with the methods of counting samples to determine free silica. Konimetric and gravimetric techniques for dust sampling are compared and contrasted. [Radiation Measurements] Both collective and personal dosimetry systems are used in the Canadian uranium mining industry and lectures are presented on each. Techniques and possible sources of error are discussed for a variety of radon and radon daughter measurement methods - Lucas method, Tsivoglou and modified Tsivoglou, Kusnetz, Rolle. Instant working level meters and personal alpha dosimeters are explained in terms of calibration, maintenance, readout and estimation of accuracy. A lecture outlining dose estimation by means of bio-assay, whole-body counting and the use of TLD's concludes the topic. Record-Keeping An overview of the problems of changing limits,

Jan 1, 1981

By Mark L. Mott

The Pittsburgh Safety and Health Technology Center of the Mine Safety and Health Administration (MSHA) has developed the Mine Emergency Responsiveness Development (MERD) program to improve the reaction and re¬sponse of mine personnel in mine emergency situations. The MERD program simulates problems that may occur in underground mine fires and explosions or surface mine accidents. Since its inception in 1982, the MERD program has been presented to MSHA, industry, labor and state government personnel. This versatile program is easily adapted to suit various training requirements. In 1992, a Mine Simulation Laboratory was built at the Natinal Mine Health and Safety Academy, Beckley, WV, to improve training for mine emergencies and prevention and fighting of mine fires. This facility is capability of simulating a coal mine and metal-non-metal mine for training purposes. It has been included in the MERD program to provide realistic and practical training for mine rescue teams and MERD partici¬pants in advanced mine emergency operations. The objectives of the MERD program are to improve the organizational and management skills of the participants in a rescue and recovery operation and provide a better understanding of the importance that various roles have on the overall organization and the importance of their interaction. The MERD program is not intended to provide the participants with all of the abilities and knowledge required to respond effectively to a mine emergency. Rather, it is intended to give the participant an opportunity to experience the emotions, frustrations and successes of a mine emergency without having to actually be involved in one. The participants are expected to return to their regular jobs with a greater appreciation of the environment in which emergency operations take place. Experience in mine emergencies is extremely limited in the industry today. The participants are encouraged to use the knowledge gained during a MERD program to develop or enhance a mine emergency plan suitable to their needs.

Jan 1, 1993

By Barbara S. Parrish, I. S. Parrish

For two consecutive years the author and his wife have been fortunate enough to have been invited by the Peoples Republic of China to work with Chinese geologists of the Geological Bureau of the Ministry of Metallurgical Industries (MMI). Our visits, each of which lasted 7-8 weeks, took us to northwestern Sichuan, central Anhui, and much of Hebei Province, as shown in the accompanying drawing. We were asked to evaluate, criticize, and offer suggestions on the exploration and mining techniques used by the Chinese. Our commission both years was centered on gold, although we were also to visit other operations when the opportunity arose. In 1986, the visit primarily concerned with disseminated "Carlin" type gold deposits; in 1987, with "Greenstone" type gold deposits. Gold has been targeted by the Chinese as a metal of importance to the nation. Several governmental agencies have received direction and budgets to seek and develop gold properties. Besides the Ministry of Metallurgical Industry, gold is being sought by the Ministry of Geology, the China Gold Corporation, and reportedly the Peoples Army. There is considerable competition among these agencies. It is not uncommon to find two or more agencies working in the same general area. However, communication between the groups is minimal. Last year, we toured a small mine at Bambishan. We could see a diamond drill across the valley. The rig belonged to another Ministry and my guides voiced their curiosity to know what their competitors were finding. Mining, too, is not the monolithic bureaucracy that most Westerners anticipate in China. There are various levels of mining. These differ not only in sophistication, but in ownership. First, for small deposits the state allows "Peoples Mines". These can be owned and worked by individuals. The individual owner-miner may hire relatives or neighbors and give them a wage or he may turn the mine into a joint ownership situation. They

Jan 7, 1988

By Thomas J. Lien

AMAX Coal Company has constructed the first commercial demonstration sub-bituminous coal dryer at its Belle Ayr Mine south of Gillette, Wyoming. This 215 ton per hour facility is projected to produce 165 tons per hour of dried coal at 10 percent moisture and 10,800 Btulpound (6,000 KCIkg). Approximately 43 tons per hour of water will be removed from the coal and seven tons per hour of coal burned as fuel.

Jan 1, 1989

By Ted D. Johnson

INTRODUCTION The report of the workshop on Alternate Energy Strategies estimated that the world's reserve of uranium oxide is about 700,000 tonnes. In order to extract these reserves, it is estimated that between 100 and 200 million tonnes of solid waste and of the order of 1 billion cubic meters of liquid waste will be generated. In addition, radium within tailing will continue to generate radon gas as it decays for many years after closure. Hence, the handling, storage and possible use of uranium mine waste is a matter which deserves serious consideration and planning. Since the properties of the waste will largely dictate the method of handling and storage or use of the waste, the properties of the waste should be determined, to the degree possible, prior to the design and subsequent operation of the mine. Uranium mine waste has both solid and fluid constituents. The solids include soil and rock removed during site preparation, similar material removed during development of the mine and uranium tailing generated by the mill. Soils can be stockpiled for reuse during reclamation or used as earth materials for construction of fills, roads, dams and soil linings. Rock can be stockpiled, used as mine backfill or can be used for earth construction in fills, roads and dams. The tailing is usually placed in a tailing storage area. The fluid constituents are both liquid and gaseous. The liquid waste is generally composed of the mill water; however, additional waste water can be generated by dewatering processes and diversion of surface runoff. The gaseous constituent of the uranium mine waste is radon generated by the radioactive decay of radium in the ore tailing. DEFINITION OF PROPERTIES The following presents a brief definition of some of the more important properties discussed later. The definitions are not intended to be comprehensive, but are useful as a basis for understanding.

Jan 1, 1980

By R. K. Singhal, R. D. Lama

Underground coal mining systems have kept pace with developments that have occurred in other types of mining. A diversified group of machines are now available with high horsepower motors, built-in microprocessor technology, and numerous options to satisfy miners' needs in various geological environments. The results will be a greater degree of mechanization and recovery of coal from inclined seams, thins seams, and seams mined in lifts from shallow as well as deeper deposits. This article is based on a general suvey carried out by the authors to detemine the current status of mechaniztion and systems development in underground coal mining. It indicates that the next two decades will see increasing use of longwall mining, which has already reached a high degree of sophistication. Automation, remote control, and robotics are the key words of the future. Data transmission from underground to surface and over long distances will be almost routine. Many components of the high technology industry that are just being considered by the mining industry regarding equipment health and perform¬ance monitoring, quality control, application of expert systems, and computer networking will become a routine part of underground mining technology. Within the next 21 years, "manless" mining, first attempted about 25 years ago, will become a reality. References to any trade name are meant to aid understanding of the text and do not imply endorsement by the authors or their users. Current coal face developments Developments in underground mining equipment, its application, and associated technology have made phenomenal progress compared to those in other types of mining. Room-and-pillar systems, on one hand, and longwall mining, on the other, have sophisticated equipment at their disposal. Both of these systems have become highly productive, with output per manshift about 50% higher than that achieved a decade ago. Continuous miners continue to be the mainstay of room-and-pillar coal mining. Numerous developments, how-

Jan 1, 1989

By R. A. Paul

WIDCO, operator of the Centralia Coal Hine, chose dredging, a method not commonly used for overburden removal, as the fastest, safest, and most economical method for mining through an alluvial filled valley. Now that the work has been completed, how did the cost and schedule compare with the original estimates? What would we do different next time in preparing for a dredging contractor? What are the potential pitfalls working with a dredging contractor? Would we do it again? When should dredging be considered as an overburden removal option?

Jan 1, 1989

By David L. Rife

Introduction Our society is currently experiencing a change in civil philosophy toward US industrialization. We have become increasingly bent on the pursuit of a nirvanic state of zero risk. The money supply has become inversely proportional to its sources. And most mining companies, traditionally conservative, have become increasingly risk conscious. Rising taxes, high inflation, and decades of a steadily decreasing gross national product (GNP) - coincident with moral decay and disarmament - have eroded America's economic health. Psychology of US metal markets has shifted across the economic spectrum to disillusionment and discouragement. The sagging national economy, expanding governmental debt, and a backward mineral policy in concert with worldwide unrest and turmoil have caused great volatility in the metal markets. Congressional inaccessibility of US resources has contributed to its loss in strategic leadership and dependency on foreign suppliers and the common market. Large scale mining activities are now on the decline. And there is an overall slump in mineral exploration in this country. America now faces the sobering reality of almost total importation of 13 key mineral commodities and total dependence on foreign sources for five of them. There is a growing dependency on 21 of the 34 minerals vital to the US economy. And virtually everything needed can be imported directly from third world countries. Almost 85% of the free world's supply or production of vanadium, chromium, platinoids, manganese, and titanium - an essential to the aerospace industry - comes from South Africa. That country now plays a forefront position in supplying the West with minerals. The Soviets have become increasingly aware of this situation. They have made key moves in procuring for their own purposes major raw materials markets, particularly in South Africa. This is obviously threatening to the US' direction and brings about vulnerability to shortages and cutoffs. In spite of these developments and the overall change in the mining industry, there is good opportunity for growth ahead. The way has been paved for the smaller mining companies, particularly the more bullish of these. Smaller mining organizations possess a tight management and strong sense of direction. They can easily adapt to and cope with change. "Windows" that exist in the industry directly depend on a number of factors. These include the busi¬ness climate, market research and planning, management and human resources, applied appropriate technology, favorable hunting ground, and entrepreneurship. Mining as business Mining (and exploration) as a business is by its very nature highly speculative. It involves greater risk for a longer period of time than most other businesses. The entire mineral estate in the US continues to shrink. This is primarily because of various legislated wilderness measures. Consequently, the probability of finding an economic ore deposit in the US has decayed to less than 1%. Although the risk is high, the stakes far outweigh the gamble and are larger than most other businesses can offer. Mining properties, as investments or business opportunities, can provide effective hedges against long-term inflation because the real price for selected commodities, such as gold, may sometimes rise faster than inflation. Recessionary periods seem to provide the best climate for entering the mineral business or for a particular mining organization to expand its activities. Looking ahead and seizing opportunities during a depressed market will pay off. Property payments and royalties are likely to be lower. And the potential for an upward shift in prices for a given commodity is very positive. The decision to invest in a prom-

Jan 9, 1985

By R. C. Freas

Limestone is a basic raw material in the production of cement, lime, a wide variety of industrial products, and a significant percentage of the crushed stone produced in the United States annually. It is used in fluxes, glass making, mineral fillers, environmental applications such as flue gas desulphurization and water treatment, soil conditioners, animal feeds, and as a construction aggregate. This presentation provides an overview of limestone distribution in the United States, it’s production, the variety of products produced, and a brief review of the primary uses for limestone.

Jan 1, 2006

High pressure grinding rolls have found widespread acceptance for cement processing, and are now making their debut in the metalliferous minerals industry. Significant energy and wear material savings appear achievable in many applications. This paper re- views the technical literature on this important, emerging technology.

Jan 1, 1997

By D. K. Sitler

Continuing advancements in manufactured diamond materials as used in rock cutting tools have created a new generation of high production tools for mining. This paper reviews the three major manufactured diamond product types available in the mining industry as supplied by General Electric Co., Specialty Materials Dept., and examines the ways these materials are used. As an integral part of this examination, the economic impact of manufactured diamond tools is evaluuted. Time and again, one will find that the premium price for these tools is economically justified when compared to traditional tools.

Jan 1, 1988

By B. K. Kejriwal, A. K. Ghose

Under specific geological environment, the full extraction of a coal seam is not possible either because of its extraordinary thickness or the presence of surface structures and bodies of water or because of the conditions prevailing in upper seams. Not uncommonly, therefore, for working such seams, pillars of coal are left for the permanent support of the overburden, and voids around the pillars are filled with sand to strengthen the pillars and prevent their deterioration with time. However, the paucity of river sand has focussed attention on the need for alternate strategies including trials with partial filling of the voids. This study has sought to examine in the laboratory the effects of partial and complete filling on the ultimate load bearing capacity and post-failure behaviour of small, tall pillars using artificial material.

Jan 1, 1986

By Barbara C. Schickner

No group has been harder hit by the problems confronting the coal mining industry than small, independent surface mine operators in the eastern US. Burdened by costly government regulations, major capital shortages, declining productivity, high unemployment, and idle and closed mines, many in the industry think the breed will not be able to survive much longer. But there are a few sole owners fighting to remain independent-and succeeding. John Wagner is running a coal stripping operation in northwest Pennsylvania on a unique blend of aggressive management and marketing, support from a team of blue-chip professionals, and some unusual tactics. Though Wagner's approach is hardly an across-the-board formula for survival-he is currently reorganizing under Chapter 11 of the Bankruptcy Reform Act-a look at his operation helps illustrate some of the unique problems confronting eastern surface miners.

Jan 2, 1980

By Ke Yang, Kai Zhang, Xiaolou Chi, Xiangyang Zhang, Yingming Li

Based on the research background of 1303 working face return air roadway in Jinyuan Zhaoxian Mine, Shaanxi Province, a method of determining the reasonable spacing of boreholes is proposed based on the stress transfer degree of coal above and between boreholes, combined with the law of plastic zone and energy evolution by theoretical analysis and numerical simulation. After drilling pressure relief, the average daily energy of microseismic events decreased by 70%, and those with microseismic energy greater than 104 J decreased by 99.2%. The research has a strong guiding significance and research value for determining the reasonable distance of borehole pressure relief.

Jun 25, 2024

By E. Haug, Quamrul Ahsan, R. Norcross

Cyanide leaching is the most common process employed in the majority of the gold extraction plants. These gold extraction plants naturally generate tailings and/or effluents that contain highly toxic cyanides, In geographic locations with excess precipitation and therefore net positive water balance, a portion of these tailings must be discharged. Before these highly toxic cyanide-containing effluents can be discharged to the waterways, cyanide and any other toxic substance must be destroyed. Geographic locations with high evaporation and low precipitation, as in the western USA, result in net negative water balance and therefore these plants can operate with a zero discharge option. However, with the current stringent environ­mental regulations and concerns for bird and wildlife mortality, even these operations may be required to partially treat their tailings to preclude potential harm to wildlife. Furthermore, heap leach opera­tions are now generally required to detoxify the heaps before abandonment. It is, there­fore, apparent that all gold extraction plants may be required to install some form of effluent treatment in order to achieve the above objectives,.

Jan 1, 1990