Search Documents

By L. R. Freitas, A. K. Resende, J. A. Oliveria, K. L. Gonçalves, L. F. D’Assumpção, L. R. Lage, J. D. Neto, F. Viveiros

Pará Pigmentos S.A. (PPSA) is an association between the Brazilian companies CVRD and CADAM, Mitsubishi Corporation of Japan, and the IFC (World Bank) created in 1992 in order to recover kaolin from Rio Capim deposit, northern Brazil. Commercial production at PPSA started in August 1996 using a process comprising mining and beneficiation at the mine site, pumping through a pipeline and drying/loading at the port site on the Amazon river estuary. Presently, all PPSA production is concentrated on 82% <2um, high-brightness coating clay shipped in bulk. In this paper, a detailed description of the development of PPSA beneficiation process is presented. The results of laboratory and pilot plant studies under- taken to develop alternative grades of clay, such as delaminated and calcined kaolins, are also discussed.

Jan 1, 1998

By E. D. Dainty, B. E. Enga, D. L. McKinnon

Following considerable laboratory studies concerning particulate control systems for underground use, a program was commenced to develop practical real life implementation systems. This program covers the implementation in seven mines of particulate filter systems to 10 engine models from three engine manufacturers in 12 different vehicle types, a total of 24 vehicles. As the program ran, one mine had to drop out and a mutually agreed upon system could not be arrived at for another. Hence, the program included five Canadian mining companies. Several of the vehicles trialed at Brunswick Mining were trialed by Brunswick themselves. Nonetheless, the data is presented. This paper covers the work performed from the beginning to the end of the demonstration program. Data collected to properly select and design filter systems along with technical conclusions of the demonstration are presented. Also presented are the results of a survey that highlights the participating mines&apos; acceptance of the technology.

Jan 1, 1991

By Florence Munter

This paper provides a discussion of the various federal and state laws governing water quality as related to mining operations. The specific laws addressed are the Clean Water Act, and the Arizona Mined Land Reclamation Act. Topics that will be addressed are mine water and process water discharges, storm water discharges, pollution prevention, dredge and fill, spill prevention control and countermeasure plan, and surface water protection. Proposed changes to the laws and regulations will be discussed. Compliance strategies will be suggested to prevent potential noncompliance and enforcement.

Jan 1, 1996

By John O. Marsden

The project development metallurgist is faced with an interesting dilemma: The use of overly conservative metallurgical projections and cost estimates can kill a project that has the potential to provide needed jobs and growth to a company&apos;s bottom line. On the other hand if the metallurgist uses a highly aggressive approach by trimming capital and operating cost estimates to the bone and by applying highly optimistic metallurgical projections, there is a risk of creating a project that can never live up to expectations. The metallurgist must walk a tightrope between "sandbagging" and "overoptimism," and this tightrope is fraught with political intrigue and difficulty. This paper takes a some- what lighthearted look at some of the political aspects associated with this issue, and other issues, and offers a few guidelines for walking the "political metallurgical" tightrope.

Jan 1, 2001

By André Vervoort, Jef Caers

Compound lognormal distributions serve as new generalized distribution laws for analyzing and estimating ore value distributions or related properties such as the average ore grade. These models are an alternative to the well known lognormal distribution. They are the translation of general geological constraints on the genesis of the deposit cumulated in suitable statistical properties. In this paper a maximum likelihood framework is established for estimating the parameters of such laws or parameter functions thereof. It is shown that under certain conditions maximum likelihood estimation is accurate and efficient in estimating the mean value even when relatively few samples are available. The method is based on a numerical maximization of the likelihood function of these models given the data. Confidence limits on these estimates are set up using resampling techniques such as the bootstrap. By this a complete methodology is presented for inference on ore grade distributions such as is shown in an example of gold data from the Merriespruit mine (South Africa) and the diamond size distribution of the Bougban deposit (Guinea).

Jan 1, 1996

By Y. C. Kim, M. Preston, F. Martino

Because of the high cost of obtaining coal washability samples, it has been difficult in the past to obtain washability variograms. As a result, it could not be determined if the geostatistical prediction tool known as kriging can be applied to predict in situ coal washability characteristics. This paper presents the obtained variogram models for the Upper Freeport coal seam in western Pennsylvania. Variogram model parameters are presented for a total of 27 models. They are for four different variables: float- weight, ash, sulfur, and Btu, at seven different specific gravities: 1.275, 1.300, 1.325, 1.400, 1.600, 1.800, and 1.80,Sink. Based on the obtained variogram results, it can be con¬cluded that all attributes of coal washability show definite spatial correlation structures, and, consequently, geostatistics can be used to predict the in situ coal washability characteristics.

Jan 1, 1990

By I. Iwasaki, J. N. Orlich

The effect of slurry rheology and ball coating characteristics on the abrasive wear of grinding media and the rate of grinding were studied using -10 mesh quartzite in laboratory marked ball wear tests. Pulp viscosity was found to be closely related with both the thickness and physical characteristics of the coating affecting abrasive wear. The packing density of particles at the ball surface was the primary determinant of wear while the grinding rate was more dependent on viscosity and thus the ball coating thickness. The optimum grinding rate was achieved when the coating thickness was about twice the largest particle size.

Jan 1, 1988

The processing capability of a semi-autogenous (SAG) mill is greatly affected by ore geology and operating variables within the mill. The SAG mill is problematic because it cannot be conveniently studied on a smaller, laboratory-scale mill. The interior of the mill, where grinding takes place, cannot be observed using instrumentation available today. Yet the motion of the rock and ball charge determines the power draft and hence capacity of the mill. Therefore, mill optimization is pursued with a charge motion simulation software. This software uses the discrete element method to describe the individual motion of numerous ball and rock particles in the mill. It is shown that by simply increasing the chord length between the lifters and increasing the face angle of the lifters the capacity of the mill can be increased. Such a configuration of lifters allows the operator to increase mill speed, hence drawing higher power while considerably minimizing direct ball strikes against shell plates and lifters. A case study of a 36 ft. diameter x 15 ft. long mill is presented. Reducing the direct ball strikes leads to lesser steel consumption both in terms of balls and lifters.

Jan 1, 2000

By J. Hallowell, M. Conley, R. Cook

Inflatable friction rock bolts (IFRBs) are often considered temporary ground support due to their susceptibility to weakening from corrosion. The effective service life of an IFRB can be difficult to estimate due to the multitude of factors that affect the rate of corrosion. Some mine sites have experienced several-year-long service lives of IFRBs without issue, while others experience corrosion-related falls of ground only weeks after installation. The most common industry method of assessing bolt performance is by pull testing the fixture. However, due to the IFRB’s ability to mobilize its full tensile capacity with less than 2 feet of anchored length, corrosion along the bolt at depths greater than 2 feet from the collar cannot be identified using this approach. Alternatively, reinflation testing is a simple and non-destructive method of evaluating the condition of an entire bolt length for breaches in the bolt wall. This can be particularly useful when assessing the extent of corrosive conditions within a particular mining area where instabilities have already occurred and the condition of nearby bolts is unknown, or when re-entering historic mine workings which have not been monitored.

Feb 1, 2023

By Ernesto Maldonado, Jesus Romero Benitez, Zach Agioutantis

Numerous researchers worldwide have investigated the prediction of ground movements due to underground coal mining utilizing different analytical, empirical, and numerical models. These studies have primarily focused on the development of prediction methodologies for either flat or gently dipping seams under variable topography, and only a few studies are available that have investigated the prediction of ground movements over inclined seams. Although most inclined coal seams are in China, India, and other countries worldwide, a few inclined coal seams (with a dip of 10 degrees or greater) are also present in the US. Currently, the prediction of ground movements for inclined coal seams using empirical methods utilizes the same methodology for horizontal seams. It consists of dividing the inclined seam into horizontal segments, calculating deformations due to each segment, and superimposing the calculation results. This paper presents a new tool that provides a methodology for modeling subsidence under inclined seam conditions. Examples based on subsidence measurements available in the literature are presented. The goal is to implement this methodology into the Surface Deformation Prediction System (SDPS).

Jun 25, 2024

By Edwin G. Johnsen

Underground mining is relatively safe today, but no technique or equipment is completely fool proof and 100% reliable. The only sure way to prevent accidental death or injury to underground workers is to remove them completely from the hazardous environment. This alternate approach to underground work is now feasible. Tunnelling and mining systems can be built that could be remotely controlled by men operating consoles in a surface control room. This concept, called a teleminer, would use recently developed remote control technology to remove man from underground work but still give him the capability to remotely operate mining and excavating equipment as if he were actually in the working area. It is appropriate to present this concept in the session "Environmental Controls" because the rationale for environmental control in underground areas can be significantly modified if man is excluded from the underground operation. The development of teleminers cannot only reduce or eliminate most of the requirements for conventional environmental control, but it can also create new and powerful techniques for rapid tunnelling and excavation. TELEMINER CONCEPT The concept of remotely controlled mining machines is neither new nor untried.(1)(2) Conventional remotely controlled mining equipment employs the standard techniques of extending the controls of the equipment to a remote console. For example, the rotary cutters on a remotely controlled tunnelling machine are started or stopped by a human operator turning a switch on the remote control console.

Jan 1, 1997

By G. Chancellor

"INTRODUCTION The paste plant is located at the Barrick Goldstrike mine in Northern Nevada on the Carlin Trend. The Goldstrike property consists of an open pit and an underground mine; along with two processing facilities: a roaster and an autoclave. The underground portion of the mine produces approximately 1,800,000 ore tons per year and approximately 400,000 ounces. The mine is broken up into four distinct zones: Banshee, Meikle, Rodeo and Northpost. The current paste plant services both the Rodeo and Northpost zones. Development of the conceptual designs and permit approval for this plant was an extensive process that took over a decade to complete. A testing program was developed in conjunction with this process and implemented throughout to ensure the following metrics were achieved: ensure no environmental impact, material available onsite would be able to flow through the pipe to all required locations, and that this material could achieve the appropriate final strength. PLANT AND UNDERGROUND CONSTRUCTION This is the first paste plant to be built in Nevada. The paste plant at Goldstrike began construction in January 2012 and was completed in March of 2013. This plant was constructed to service the Rodeo side of the underground mine which previously utilized a cemented rock fill (CFR) plant to meet their backfill needs. However, in March of 2013, the same month the plant was commissioned, the raise that fed this CRF plant was mined out in a planned phase of the adjacent open pit. This made the switch to paste all the more difficult as it was being relied on for as the sole source of backfill production even though the system yet to be fully tested and optimized. The plant was designed to be fed with onsite Roaster tailing which would be thickened and then mixed with cement and fly ash. The plant was designed to pump 177 tons of paste per hour with a utilization of 65%. The original design specifications for the paste were 77% solids with varying binder contents depending on where the paste was being placed"

Jan 1, 2015

By W Frint

An area in Southwestern Wyoming is rapidly becoming the soda ash capitol of the world. Starting only 20 years ago from a unique deposit of trona, the out-put has rapidly increased until now about half of the soda ash produced in the United States comes from this area. Chemically, soda ash is sodium carbonate, a large tonnage, widely used alkali. The largest single industrial use is in glass manufacture, where 25 tons of soda ash are used in producing 100 tons of glass. Other big users are the detergent and chemical industries. The trona deposits in the Green River basin of Wyoming, were formed about 75 million years ago as part of a geologic period when an ancient lake alternately went through periods of being a large fresh water or smaller brine lake. Today these deposits lie from 800 to 3000 feet below the surface in a semi-arid, almost desert region just west of the Rocky Mountain Continental Divide at an elevation of 6200 feet. In this area there is a prevailing westerly breeze and almost every afternoon the velocity reaches very windy conditions. Rainfall is minimal, being only 6-8 inches of moisture per year with an evaporation rate exceeding 24-inches. Most of the moisture comes in winter snows or summer thunderstorms. Temperatures are low with below zero weather dur¬ing most of the winter and early morning frost is not uncommon during the summer months. There are many trona beds varying in thickness from a few inches up to 15 feet. The deposits now being mined vary from 8 to 10 feet in thickness. The ore is mined by driving tunnels either via conventional explosives or with continuous boring machines. It is transported to the shafts via conveyor belts

Jan 1, 1972

By S. M. Hsiung, Wen H. Su, Syd S. Peng

This paper examines the interaction problems of multiple seam mining by combining underground investigation, laboratory testings, and numerical modeling. One case of multiple seam interaction that occurred recently in West Virginia was carefully studied. Causes for the interaction problems were identified and the corresponding mining recommendations were proposed. The principle of pillar columnization and the effect of a remnant pillar on mining operations in the underlying and over- lying seams were also carefully examined. Considerable attention was given to the effect the pillar size, the pillar width, the coal stiffness, the extraction ratio, the degree of inhomogeneity in the interburden, the overburden thickness, the mechanical properties of the interburden rocks, the strata inclination, the interburden thickness, and the in-situ horizontal stresses have on the pillar load transfer mechanism.

Jan 1, 1986

By S. K. Kawatra, T. C. Eisele

Under normal conditions, a significant amount of pyrite is recovered in the froth during flotation of high-sulfur coal. To reduce this pyrite recovery, it is first necessary to determine the primary recovery mechanism, because different measures are required for reducing entrainment, locked particle flotation or true hydrophobic flotation. In this paper, evidence is presented that suggests that hydrophobic flotation is not the major mechanism for recovery of liberated pyrite; instead, the bulk of the recovered pyrite results either from simple entrainment or from being physically locked with floatable coal particles.

Jan 1, 1993

By R. S. Das, A. K. Sinha

Modern mine ventilation systems have grown rapidly in recent years both in terms of complexity and value for human health and safety. Although computer models are now available to help the design and operation of mine ventilation systems, considerable differences often exist between the computer-based predictions and practical results. Research conducted to compare computer results with practical measurements made in ventilation circuits simulated in a physical model seems to confirm such differences. It is concluded that although a mine ventilation computer model is a very powerful tool, it can be utilized to its full potential only if reliable input data are provided.

Jan 1, 1987

By Raj K. Singhal

This paper is a report on a task force study dealing with many facets of computerization. The primary mandate of the task force was to examine the software and hardware currently available for application relating to reserve estimation, mine planning, economic evaluation, equipment selection, production scheduling and composite mine simulation and to evaluate how adequately the software fulfills the user needs in surface mining of oil sands and coal. To meet its objectives the task force consulted extensively with the users, developers and suppliers of hardware and software. The paper outlines the approach taken by the task force to fulfill its mandate, summarizes its findings and presents some pointers which might be useful to others considering this type of evaluation.

Jan 1, 1986

By R. Hogg, A. C. Maffei, D. T. Ray

Based on standard population balance models for agglomeration and size reduction processes, a simplified model has been developed to describe simultaneous growth and breakage in the flocculation of agitated suspensions. The results of semi-batch flocculation tests have been used for estimation of the model parameters and empirical relationships have been obtained to describe the effects of process variables and to establish scale-up criteria. Application of the model to the design, operation and control of continuous flocculation processes is discussed.

Jan 1, 1990

By S. El-Mofty, P. Zhang, N. A. Khalek

This article reviews different technologies used for beneficiation of siliceous and calcareous phosphate ores of different origin. The review sheds light on recent trends suggested for solving problems associated with separation of different impurities from phosphates. Applications of recently modified flowsheets as well as new reagents in the flotation of phosphate ores of sedimentary origin are highlighted.

Jan 1, 2003

By Lynn B. Hales, Randy Ynchausti

Expert systems are now being used effectively to streamline and improve the performance of supervisory computer control strategies. Their advantages have led to use in both batch and continuous applications. Expert systems in the context of real-time process control, will be defined and examples of their successful implementation in autogenous, semi-autogenous and ball mill grinding circuits will be discussed.

Jan 1, 1990