Search Documents

By G. W. Rhodes, B. P. Cavan, F. K. Mussger

The New Austrian Tunneling Method (NATM) has been successfully applied to two very different tunneling projects in the U.S.. In the case of Pittsburgh's Mt. Lebanon Tunnels, two original design alternatives were prepared. The NATM alternative incorporating a reinforced shotcrete final lining was successfully bid and constructed. At Washington Metro's (WMATA) Section B-10 Glenmont Route, Wheaton Station and tunnels, a NATM value engineering redesign was prepared for the low bidder. The design incorporating a waterproofing system based on a PVC membrane between the initial and final linings was accepted by WMATA. In both cases, European experience and standards were meshed with U.S. standard practice. Examples of NATM flexibility as an original design and as a value engineering proposal are presented.

Jan 1, 1985

By Ben L. Seegmiller

INTRODUCTION Site characterization using oriented borehole core is the subject of this paper. Borehole core is a standard source of data for rock mechanics investigations. Oriented borehole core provides data whereby the geometric orientation of various geologic discontinuities (faults, joints, bedding, etc.) may be determined. The orientation and strength characteristics of discontinuities are important in many engineering investigations and in particular, in slope stability analyses. In heavily vegetated or soil covered situations, oriented borehole core may provide the only means of assessing the subsurface planes of weakness which characterize the site. The purpose of this paper is to briefly describe various methods or orienting core, core characteristics which may be logged and the methods of processing and using the data for site characterization.

Jan 1, 1977

By Natesa Jayaraman, Jon C. Volkwein, Edward D. Thimons

The Bureau of Mines has studied the impact of shuttle car movement on face ventilation. Real-time measurements of air velocity, methane gas, and respirable dust were recorded and compared with a time study of face shuttle car movement. Work was conducted in a blowing face ventilation section where a scrubber-equipped mining machine operated. Air velocities decreased by an average of 35% as the shuttle car entered the face, restricting air flow, and increased by an average of 35% as the shuttle car pulled away from the face, drawing with it additional air. Return air methane levels follow the face air flow volumes, decreasing as air volume increases. The surge of air created as the shuttle car leaves the face helps to dilute methane. Respirable dust levels, however, were found to increase as the air flow increased and decreased the scrubber capture efficiency.

Jan 1, 1989

By Owen E. Owens

INTRODUCTION This paper deals with the main components in exploring for and developing a gold ore deposit. It addresses geology, exploration drilling, ore reserves, and evaluation criteria in an integrated manner to present an overall picture. Gold forms such a small component of a gold ore body, that particular care should be taken in dealing with the data from a developing deposit. The paper lists the main gold ore deposit types and their character. Their differences, as well as differences to other types of ore deposits, are important to understanding exploration approaches, and problems of ore reserve definition. Gold exploration has enjoyed a great boom in recent years. Many new ore deposits have been developed but experience shows that definition of gold is not a simple straight forward process and this outline attempts to point out some of the important aspects of ore reserve definition including some pitfalls. GOLD DEPOSIT TYPES The Witwatersrand deposits in South Africa produce about 50% of the world's gold. The gold occurs as fine grains in thin beds within gently dipping quartz pebble fan conglomerates usually with associated pyrite grains. It is characterized by rather uniform distribution of gold along thin layers within the conglomerate.

Jan 1, 1988

Due to the ongoing restructuring of the mining industry in central Europe with a continuous decline of the number of large underground mines and collieries, and a simultaneous decline of staff numbers in the remaining mines, the established mine rescue schemes are endangered to collapse. With the end of the mine rehabilitation at Wismut Uranium in 2014, the last remaining major mine rescue teams in Saxony, providing basic mine rescue services for all other mines in the region, will disappear. This will leave a large number of small mines and other underground operations without capable mine rescue support. Since none of these companies is able to set up a complete mines rescue unit on its own, new ways have to be found. Among others, a central mine rescue team for central Germany as well as the assistance by special trained professional fire fighters or mine rescue teams from abroad are discussed. Problems like location of the central rescue team, financing, communication and transport have to be solved. This paper provides an overview over the complexity of the problem as an example for other mining regions worldwide and will discuss national and cross-national strategies.

Feb 23, 2014

By R. Kanniganti, M. Karmis, C. Haycocks

An extensive review of multi-seam under-mining literature was conducted and a data base of case studies was assembled . A critical review of the design principles outlined in this literature resulted in the compilation of specific design criteria for the design of lower seam mines. Analysis of this criteria demonstrated the necessity for a protocol for the design of unsymmetrically loaded pillars. Such a design criteria was developed using finite element methods for a wide range of possible loading conditions. This design criteria can be utilized for underlying pillar design when the loading conditions can be determined. To facilitate using all the under-mining research results by field/planning engineers a Windows TM based software package was developed. This software package contains a multi-seam tutorial, analytical tools and a case history database. The package is user friendly and fully interactive and supported with extensive on-line help. The package contains numerous case studies of multi-seam mines that can be reviewed to facilitate analyses.

Jan 1, 1996

By Steve Kral

"The Rapid Excavation & Tunneling Conference (RETC) is a world-renowned event that attracts some of the best minds in the global underground construction and tunneling industry. The experts gather at this conference to impart new technologies, discuss challenges to their projects and learn about new technologies that have become available to them.The 2015 RETC will be held June 7-10 at the Sheraton New Orleans, in New Orleans, LA. This biennial conference, of which SME is a sponsor, is expected to attract about 1,400 attendees from around the world. These professionals represent all parts of the global tunneling and underground construction industries - contractors, engineers, owners, consultants and equipment suppliers.More than 110 technical papers in 21 sessions will be presented over two-and-a-half days. Paid attendees will receive a proceedings volume of the conference. The proceedings will also be available from SME. In addition to the technical programming, the accompanying exhibit will include 155 exhibitors occupying 175 booths, providing RETC attendees the opportunity to get a look at the latest in equipment and service technology. Three short courses will be held on the Sunday preceding the start of the show. And there will be plenty of opportunities for attendees to meet and chat during several social activities that are scheduled throughout the conference."

Jan 1, 2014

By S. B. Bealko

Mining haul trucks comprise the majority of the equipment used in underground limestone mining operations and are known to emit high levels of noise. A previous study conducted by the National Institute for Occupational Safety and Health (NIOSH) indicates that 70-90 percent of all miners have a noise-induced hearing loss (NIHL) great enough to be classified as a hearing disability by retirement age. These results demonstrate the public health need to protect the hearing of workers in the mining industry, including haul truck drivers. ng of workers in the mining industry, including haul truck drivers. Cab enclosures present an opportunity to isolate the haul truck operator from both truck and other noise in the mining environment. A total of twenty-five haul truck cabs were studied which were divided into three style (treatment) categories determined by soundproofing features and technology for noise reduction: old-, new-, and retrofitted-style. This study examines the contribution of cab acoustics, operator performance, and maintenance to noise reduction for each cab style. Dosimeters were used to measure 8-hr time weighted average sound pressure levels (TWA8 SPLs) inside and outside the cabs to determine if different acoustical treatments affect cab attenuation. Adherence to the Mine Safety and Health Administration (MSHA) Permissible Exposure Limit (PEL) of 90 dB TWA8 (with a 90 dB threshold) was used as the main indicator of overall noise reduction achieved. Dosimetery results indicate only 2% of the samples exceeded the PEL, but samples could still be reduced much further. Descriptive and comparative statistics indicate that noise levels inside the new-style cabs are significantly lower than the other two cab styles. Also, data suggest that there is no difference in noise exposures when comparing the old-style to retrofitted cab styles. Operator influence (opening doors and windows) was a significant factor for increasing noise exposure. This paper demonstrates that properly designed cabs can achieve major noise reductions, but noise levels could still be reduced much further below the MSHA PEL. New-style cabs, equipped with modern noise-reduction treatments, exhibit much lower noise exposures than the other two cabs styles, and the effectiveness of the current noise-reduction treatments for retrofitted cabs is questionable. Haul truck driver observations indicate that improved noise exposure reduction training is needed. Finally, specific targets for future noise reduction research are suggested that will further contribute to the prevention of hearing loss for haul truck operators.

Jan 1, 2008

By Hassan El-Shall

The results of laboratory and pilot plant testing of a newly developed process to dewater waste slurries from different industries are presented. Data indicate that an increase in solid contents from 6% to over 30% can be obtained in few minutes retention time in comparison to several years as required by currently used technologies. The economical as well as the environmental impacts of such process are discussed.

Jan 1, 1992

By M. J. Hrebar

This paper reviews large dozer stripping techniques and presents results of two field studies. The first is a seven-shift study of a contour block stripping operation where a Caterpillar DII is used as the primary stripping equipment. The second is a two-shift study of two Cat DIIs dozing blast cast material ahead of a dragline operation. Surveys and continuous time studies were used to determine production rates and as a basis for forecasting unit stripping costs in both cases.

Jan 1, 1994

By J. B. Yianatos, G. S. Dobby, J. A. Finch, A. R. Laplante, R. Espinosa-Gomez

The question is posed as to why columns typically have a collection zone 10 m high (H) by 1 m in diameter (D). Three geometry dependent factors are considered: degree of mixing, Np; volumetric bias rate, B; and volumetric gas rate, G. Increasing H:D decreased Np and B, which improves performance but decreases G, which causes the column to approach overloading. Taking typical column operating conditions, it is concluded that a collection zone H:D of 10:l is a reasonable compromise.

Jan 1, 1987

By V. Saltas

The present work investigates whether dielectric spectroscopy can be used to detect contamination, which may appear in a natural porous material, due to the spreading of pollution. For this purpose, dielectric and conductivity measurements, in the frequency range of 10mHz to 1MHz, were carried out in sandstone samples, partially filled or saturated with solutions of leachates, at different concentrations. The experimental results suggest that although the role of water is dominant to the measured electrical conductivity, variations of two orders of magnitude are observed due to the different concentrations of leachates, in partially filled sandstone samples. Experimental data are well fitted with a Havriliak?Negami dielectric relaxation function, superimposed with a conductivity term. The parameters of the fitting function have been correlated to the concentration of leachate in the sandstone samples and considerable changes have been observed at low leachate?s concentration.

Jan 1, 2005

By G. Chi, M. C. Fuerstenau, R. C. Bradt

Reduction of the total energy expenditure in mining and ore preparation processes was achieved by redistribution of the energy from the crushing and grinding steps to the blasting operation. Reducing the burden/spacing distance by 25% or increasing the charge length by 25% during blasting results in significant energy savings in subsequent comminution processes. The energy cost of mining and comminution is reduced by up to 10%.

Jan 1, 1995

By Vanessa M. Torres, Renato S. Costa

This work presents the experience of Cia. Vale do Rio Doce in using Diagnostic Leaching tests to characterize refractory ores and CIP tailings. With the diagnostic leaching results of the highly refractory gold ore from Maria Preta Mine (Brazil), a process flowsheet was defined for a feasibility study of possible process modification on the existing plant. With CIP tailings from its Fazenda Brasileiro and Caué operations the amount of cyanidable gold was determined to aid plant optimization.

Jan 1, 1995

By Haydn H. Murray

Common clay includes a wide variety of clay and other fine- grained rocks that are used in many ways. These clays are some- times classified as miscellaneous clay and shale. Most products made from them are fired and include such things as structural and face brick, drain tile, vitrified pipe, quarry tile, flue tile, conduit, pottery, stoneware, and roofing tile. Very large tonnages of these materials are bloated by firing to form lightweight aggregate, and large quantities are used in making portland cement (see the specific chapters in this volume). Uses not requiring firing of a finished product include filler for paint and other products and shale and clay used for packing dynamite in blastholes and for plugging oil and gas wells that are no longer in use.

Jan 1, 1994

By E. R. Spencer, E. R. Bauer, G. P. Cole

Overexposure to hazardous noise has been found in most mining sectors, with up to 100% of the surveyed workforce experiencing a noise dose that exceeds the U.S. Mine Safety and Health Administration (MSHA) permissible exposure level (PEL). As a result, miners show elevated rates of hearing impairment of 70-90% by retirement age. To help manage noise exposures, the U.S. National Institute for Occupational Safety and Health (NIOSH) developed the Determination of Sound Exposures (DOSES) software and implementation guide for use by mine management and safety personnel. This paper describes the development, functions and basic operation of the initial-release version of DOSES. A revised version is being developed to incorporate additional user-suggested functions, and its development and implementation to assess noise control solutions will be described in a future article. The software relies on a time-motion study that profiles the worker’s daily activities. Observations about the worker’s location and tasks or other activities are recorded along with the start and end time, to determine the duration of the tasks so they can later be matched up with the noise data. The software gives the user the option of assessing dose relative to the MSHA PEL, the action level or the NIOSH recommended exposure limit. The software generates a variety of interactive on-screen displays showing where, when and how the worker’s noise dose accumulated. It also can generate customizable printed reports. These outputs can be used to highlight the tasks, locations and times that are associated with the greatest amount of a worker’s noise exposure. DOSES simplifies and streamlines the record keeping and analysis associated with time-motion studies and worker noise exposures, so mine management can make engineering noise control or administrative control decisions to limit the noise overexposure of their workers.

Jan 1, 2011

By E. Azrag, A. MacDonald

A hydrogeologic investigation was conducted to predict inflow to underground mine workings and mining-induced hydrologic impacts for a proposed underground mine beneath a lake in northern Canada. Flow and shut-in tests were conducted to determine hydraulic conductivity values and to estimate the hydraulic head. A conceptual hydrogeologic model was developed and incorporated into a numerical ground-water flow model (utilizing MINEDW, a three-dimensional, finite-element code with special attributes designed for mine dewatering). The mining sequence was represented in detail(e.g., driving ramps and drifts, extracting panels, and backfilling mined areas). Due to limited field data, a quantitative assessment of uncertainty was implemented to estimate limits of possible inflows.

Jan 1, 2003

By B. K. Parekh

The International Symposium on Comminution was organized at Camborne School of Mines, Cornwall England. Papers covered the fundamental and practical aspects of comminution in the mineral industry. Although comminution equipment design has not changed fundamentally during the last 50 years, methods of control and optimization have improved considerably. A simulation model for batch ball milling in the rotating mill was developed as a step toward continuous simulation of ball and autogenous milling. New concepts in jaw crusher technology design and the concept of a 1.6- x 2.1-m (66- x 84- in) jaw crusher with open feed throat has resulted in power savings. The use of cone crusher technology in comminution circuits with particular reference to machine design, plant flowsheet and control figuration has been reported by Boliden Allis, of Sweden. The Whiten steady state crusher model form has been used to develop a quantitative model of 2.1-m (7-ft) cone crushers. This was done by incorporating liner age (wear) and liner length as variables on the selection of particles for breakage and thus on the product size distribution. Another paper by Lira and Karetsky discussed the development of a model based on a multisegment ball mill developed by Whiten and Kavetsky. It is capable of simulating the performance of a coarse grinding ball mill of a given diameter, ball size and mill speed.

Jan 1, 1991

By Karl Gunnar Holter, Frank Clement

"INTRODUCTION Typically waterproofing of conventionally excavated tunnels has been done by installing pre-fabricated sheet membranes between the primary temporary support lining and the secondary permanent inner lining. The membrane acts as a separation or sliding layer between the linings, which is often desirable. The geotextile installed behind the sheet membrane provides the required drainage and protection of the system. The design of the tunnel lining is strongly influenced and limited by the use of waterproofing sheet membranes. Since primary and secondary linings are separated from each other, forming a double-shell lining system. In that case the secondary lining must be designed for all permanent loads, although the sprayed concrete primary lining continues resists ground and water loads for a long time after construction. Significant progress has been made in sprayed concrete technology over the last two decades, with advanced admixtures, as well as the improved application technology using spraying robots. The development of new admixtures like superplasticizers based on poly-carboxylates, alkali free accelerators and silica fume, enables designers to use permanent sprayed concrete linings (SCL) increasingly for long-term service life. When designed and applied correctly, sprayed concrete can be considered as permanent. The use of spray applied membranes has seen increased use over the last decade in some countries, and demonstrated functionality and cost-effectiveness in several situations. This paper describes the use of the sprayed waterproofing membrane MasterSeal 345, an EVA polymer based product, and the practical experiences from several projects. SPRAY APPLIED WATERPROOFING MEMBRANES The sprayed waterproofing membrane is polymer based and has been especially developed for underground structures. The membrane is applied between primary and secondary concrete linings and develops high bond strength on both sides to the concrete (doubled-bonded)."

Jan 1, 2016

By R. Mathur

Cu isotope fractionation in low temperature aqueous environments has been well documented. Here we apply Cu isotopes to two distinct, yet related mining problems. First, an exploration geological application where we measured copper isotope fractionation in oxidized leach caps, chalcocite enrichment blankets and hypogene mineralization in 4 porphyry copper deposits located in South western USA. Cu isotope patterns exist in the lateral and vertical distribution within the mines coupled with distinct relationships with Cu grade. Second, a hydrometallurgical application where we measured the leach fluids, feed and residues from a quick leach text of Cañariaco ores. The results indicate the relative proportions of the minerals providing Cu during leaching. Interpretations of the QLT test measurements indicate covellite is the dominant ore mineral providing Cu during leaching. Both applications clearly demonstrate the power and ability of using the Cu isotope technique to understand low temperature aqueous processed involving copper.

Jan 1, 2010