Search Documents

By J. N. Adamson

The Alcan Smelter project at Lynemouth on the Northumbrian coast draws cooling water for the power station through shafts and tunnels from the North Sea. The sea at this part of the coast is frequently very rough and even in calm weather the coastal currents are strong. The adjacent coal mine makes use of these currents to disperse colliery waste and discharges into the sea some thirty thousand tons each week. In consequence the sea bed is continuously shifting and the sea is black and turbid. Construction of sea shafts under these conditions presents difficulties as drilling from a floating vessel is hazardous and sea bed activity of divers is greatly hindered by the entire absence of visibility. After considering several alternatives a method of construction was agreed with the Consultants in which the drilling and also the lining of the shaft would be completed in sequence from an eight legged work barge (GEM 126). Each shaft would be drilled to full depth and a steel cylinder, with its ends closed temporarily, would be lowered into the hole and grouted into the formation to form a full-length permanent lining. The bell mouth for each shaft would be constructed in advance to form part of the cylindrical casing. On interception of the shaft by its appropriate tunnel the lower end of the cylindrical casing would be cut away and the internal walling of the shaft installed from below. After completion of construction the shafts and tunnels would be flooded and the bell mouth sealing covers removed by divers.

Jan 1, 1997

By Robert L. Marovelli

Organizational development that attempts to simultaneously deal both with training and with job design parameters as they relate to mine health and safety, productivity, and quality of life is one of several areas of research that the Bureau of Mines is pursuing. The Bureau sees potential in this particular effort for reducing accidents and injuries, improving worker satisfaction and health, and increasing productivity.

Jan 1, 1981

By B. Pollack, L. G. Stevens

INTRODUCTION In other chapters of this volume many of the important technical aspects in the design of concentration and dewatering circuits have been discussed. This chapter will deal with the steps necessary to bring that information together in order to produce the specifications necessary to purchase the equipment and complete the design. It deals with the plant as a whole rather than just concentration and dewatering, since the steps are essentially the same. Prerequisites to Engineering Design Feasibility studies will have been completed and design parameters established prior to the start of the engineering design stages for a metallurgical plant. The data base for the feasibility studies will have included laboratory and/or pilot plant test work, historical data, proposed plant site data such as climatology, topographic mapping, geological and geotechnical information. These studies will have established the general project design criteria as well as the process design criteria leading to the preparation of preliminary flowsheet ( s) and/or alternative process flowsheets. These will have incorporated metallurgical and material balances, allowing identification of major equipment items, and development of preliminary plant site plot plans. Preliminary technical and economic assessments and recommendations will have been prepared during this phase for Owner's review and evaluation of the technical, physical, and cost effectiveness of the overall project and its component process, process facilities, and supporting facilities elements. After Ownert s approval and decision to proceed, the engineering design can be initiated, using the above information as the basis. Engineering Design Phase The engineering design of metallurgical plants and their elements are generally developed in two sequential stages, namely: (1) Basic ("Front end") Engineering Design (2) Detail Engineering Design Figure 1 relates these engineering stages to the entire program from feasibility through construction.

Jan 1, 1986

By B. K. Sternberg

Since 1986, we have developed a series of electromagnetic (EM) sounding systems at the Laboratory for Advanced Subsurface Imaging (LASI). These may be categorized by their frequency ranges: low frequency (LF, 30 Hz to 30 kHz), medium frequency (MF, 1 kHz to 1 MHz), and high frequency (HF, 30 kHz to 30 MHz). We have applied these EM systems to a variety of targets, including: mapping of plumes of contaminated groundwater, tracing leachate for an in-situ leaching operation, locating buried hazardous waste, identifying subsidence-prone zones and detecting buried voids. These systems are also applicable to exploration for ore bodies. Currently, our sounding system uses a vertical magnetic field vector. Previous systems of this type required a slow and relatively inaccurate manual rotation of the sensing coils. The systems also used occasional calibrations of the measuring system. We have developed a 3-dimensional mathematical rotation procedure for the data, as well as a simultaneous, high-accuracy, calibration method. These new developments have greatly increased the speed of the measurements, as well as improving the accuracy of the ellipticity data. We use stepped-frequency measurements along with narrow-band filtering to allow accurate measurements, even in high-noise areas. We typically obtain ellipticity measurements at eleven frequencies and along densely sampled profile lines. We use neural networks to help interpret the measured ellipticity patterns. Neural networks can be trained to relate the measured ellipticity patterns to earth resistivities or to discrete targets buried in the earth. The neural network training may use theoretical EM responses calculated from computer codes for relatively simple structures. The theoretical EM response for many complex targets that are of interest cannot currently be reliably calculated, even with the largest supercomputers available. We have therefore chosen to do some of the training using theoretical EM responses generated in a full-scale modeling tank located at our Avra Valley Geophysical Test Site. We have also developed data-visualization software to help interpret the large data sets produced by this system.

Jan 1, 1997

By N. S. Tanious

The accuracy of vibrating wire stress meters has been questioned by various users in the mining industry. During an in situ coal pillar study, a laboratory evaluation program was developed to determine whether stress meters could produce reliable measurements in coal. More than $0 stress meters were tested for accuracy, repeatability, effects of setting pressure, and the concept of using a single curve for interpreting the stress-meter data. The testing medium was lucite, a material with a modulus of elasticity very similar to coal. The evaluation demonstrated that the stress meters did provide repeatable measurements, but that accuracy was lacking when the recommended interpretation technique was used. Therefore, a new technique was developed that required all stress meters to be calibrated in the laboratory before use in the field. This new technique reduced the average error to typically less than 10% and, in the worst case, to below 15%.

Jan 1, 1988

By M. Polat, S. Chander

Many models have been suggested in the past to obtain a satisfactory fit to flotation data. Of these, first-order kinetics models with a distribution of flotation rate constants are most common. A serious limitation of these models is that type of the distribution must be pre-supposed. Methods to overcome this limitation are discussed and a procedure is suggested for estimating the 'actual' distribution of flotation rate constants. It is demonstrated that the classical first-order model fits the data well when applied to coal flotation in narrow size-specific gravity intervals. When applied to material which is fractionated on the basis of size alone, the use of three parameter models, which were modified from their two parameter analogs such as rectangular, sinusoidal, and triangular, gave most reliable results.

Jan 1, 1995

By Anthony Edey, Leigh A. Readdy, Bruce A. Kennedy

Introduction Very little attention normally is given by the experts, or the public at large, to the fact that the majority of the oil that has been or will be discovered within the U.S. remains in the ground. The inherent limitations of oil production through surface wells, either by primary or secondary techniques, will result in a total of over 300 billion bbl of oil left in the ground after completing production by standard petroleum techniques in currently producing or producible fields. This reserve represents some two-thirds of the original quantity of oil discovered in place. Recent work by a number of groups has shown that there is strong economic justification for extracting this remaining oil by mining and processing techniques. Table 1, taken from 1977 API reports, demonstrates the oil left in place at the end of the conventional petroleum production cycle in then-known fields within th’e U.S. Possible targets for oil mining operations include (1) oil remaining in place in fields and pools that have reached economic depletion by current petroleum production methods and that are not amenable to economic recovery by conventional petroleum industry techniques; (2) oilor bitumen-saturated rocks not normally considered by the industry to constitute producible reservoirs, such as shales and diatomites; and (3) asphalt- and bitumen-impregnated rocks. Economically Depleted Fields A more detailed examination of the depleted fields shows that estimates of oil remaining in place after primary, secondary, and nondestructive tertiary recovery can vary widely. There is significant evidence, however, that more than half the estimated original oil in place (OOIP) remains in the reservoir after all petroleum extraction techniques have been applied. If one compares the sum of past oil production and estimated remaining producible reserves with the API estimate of total discovered OOIP as of 1975, it becomes apparent that for the U.S. as a whole, 67070of the 00IP will remain in place at the end of the

Jan 1, 1980

By E. D. Goddard, D. S. Murphy

Acid resistance, zeta potential and ESCA (electron spectroscopy. for chemical analysis) experiments were performed on emperador marble and four calcium carbonate samples (onyx calcite, travertine calcite, Iceland spar calcite and aragonite). Six fluorine-containing reagents were used to treat the surfaces of these materials: magnesium hexafluorosilicate, zinc hexafluorosilicate, sodium fluoride, zinc fluoride, strontium fluoride and stannous fluoride. The acid resistance of treated samples proved to be much higher than that of their untreated equivalents. The isoelectric point of treated samples approaches the isoelectric point of fluorite. Also, the fluorine content, as measured by ESCA, of a marble surface treated with magnesium hexafluorosilicate is much higher than that of an untreated sample. The binding energy off of fluorine and calcium the treated marble is consistent with the formation of calcium fluoride.

Jan 1, 1994

By F. Segobia, M. Portal, F. Ysla, L. Goicochea

It is our responsibility to promote responsible and sustainable mining with new generations, promoting a culture of equality and respect. To fulfill this commitment, we are working with the SME UNC Student Chapter team, Newmont Yanacocha, BRG Women and Allies and the Museo de Agua y Tierra (MAT) to carry out the “Building our future” project. It is our responsibility to promote responsible and sustainable mining with new generations, promoting a culture of equality and respect. To fulfill this commitment, we are working with the UNC SME Student Chapter team, Newmont Yanacocha, BRG Women and Allies and the Museo de Agua y Tierra (MAT) to carry out the “Building our future” project. This project seeks to instill in new generations the importance of mining, integrating sustainable development objectives. We have the participation of Newmont Yanacocha and external professionals, who share their life stories and inspire participants from rural and urban educational institutions to pursue their dreams and aspirations. We believe that this project is important because it will help new generations understand the importance of mining and its role in the development of the country, covering the economic, environmental and social spheres. Since its inception in 2022, the project has positively impacted more than 500 participants.

Feb 1, 2024

By K. C. Ko, M. D. Bunnell

The studied coal mi1e is an underground coal mine located in the northern Wasatch Plateau of central Utah (Figure 1) . Since operation began in 1981, in situ stress conditions have been encountered which differ from the assumed conditions utilized during early mine design efforts. Geologic structures also varied somewhat from those projected during initial geologic interpretations of the area. The encountered geologic conditions combined with the unusual stress conditions prompted a combined study of in situ stress and stress-related geologic structures. The study was conducted in two phases, with phase 1 consisting of detailed underground mapping and analysis of stress-related geologic structures to determine stress orientations from which they originated; and phase 2, consisting of over- coring two sites within the mine to determine present in situ stress orientations and magnitudes. GEOLOGIC ANALYSIS Three types of geologic structures have been encountered in the mine that act as indicators of stress orientations of the geologic past. Two of these structures, faulting, and igneous dikes, are directly measurable in the mine. A third type of structure, photolineation, was detected through remote sensing methods and shoe god correlation to roof conditions in certain areas of the mine. Faults Two major orientations of faulting have been encountered in the studied coal mine, including a system of N 80 W striking normal faults and a system of N 55 to 70 W striking oblique-slip faults. Only data collected from the oblique-slip faults were used for this study due to the fact that these faults offset the N 80 W faults wherever the two systems intersect, indicating that the N 55 to 70 W system was created by a more recent stress field. Figure 2 shows locations within the mine where data were collected from seven locations along oblique-slip faults. Data collection consisted of measurement of fault plane strike and dip, fault slickenside trend and plunge, and slip direction. The data are tabulated in Table 1. The fault data were then plotted on stereo nets to determine the stress orientations present at the td of faulting (Figure 3). The determined stress orientations are 32~0 included in Table 1. The stereo net plots show average principal stress orientations of: 1) [ ] plunge 1 degree. These data suggest that the N 55 to 70 W oblique-slip faults were produced by a nearly

Jan 1, 1986

By H. R. Thompson

The Grant Town Power Plant is a nominal 80 MW (net) Waste Coal-Fired Electric Generating Plant which is located in northern West Virginia, approximately 15 miles southwest of Morgantown. The Steam Generator consists of two (2) Pyro-Power Circulating Fluidized-Bed Boilers (CFB), each rated at 400 000 lbs/hour @ 1,350 psig. Main Steam. The Turbine Generator is a single GEC Ahlstrom unit rated at 95 MW gross and 80 MW net. The Plant began commercial generation during April, 1993. The facility is owned by American Bituminous Power Partners, L.P. (AmBit), and operated by Mission Operations and Maintenance, Inc.

Jan 1, 1996

By Charles D. Litton

This Bureau of Mines paper describes a novel fire detector that can be used to discriminate between smoke produced by a fire and smoke produced by a diesel engine. The detector uses a pyrolysis technique whereby a sample of smoke- laden gas passes through a short, heated tube within which fire smoke particles pyrolyze and increase their number concentration and decrease their average size, while diesel smoke particles are unaffected. The detector is designed for use in mines that use diesel-powered equipment where the detection of fires is complicated because of the diesel emissions background levels of smoke and other products of combustion.

Jan 1, 1989

By Donald W. Gentry

This article introduces mine planning as a complex process based on the quantitative and qualitative assessment of a myriad of independent and inter-or co- dependent variables. The interdependent variables of particular interest in this paper are those associated with mine planning activities that impact metallurgical processing plant performance and costs. These variables are identified and examples are provided to substantiate the argument that the magnitude and sensitivity of these variables must be formally assessed and analyzed to determine their potential impact on overall economics.

Jan 1, 1991

By Tzou-Shin Ueng

Rock reinforcement of rock anchors and rock bolts are commonly used for the support of large rock caverns. The rocks at the location of most large underground openings are usually under very high initial stresses prior to excavation. Hence, the stress redistribution caused by excavation will induce considerable rebound deformations of rocks surrounding the caverns. Since the pressures exerted by the reinforcement are generally far below the initial rock stresses, the reinforcement will be stretched along with the rock deformations, and the stresses in the reinforcement increase accordingly. It is not uncommon for the stress in the reinforcement to reach the yield strength, and in some cases the reinforcement may even have failed. Therefore, the increase of stresses caused by the rebound deformations of rocks should be taken into account in addition to the force required to stabilize the caverns. It was found that the measured stress increases of the prestressed tendons after installation were in good agreement with those computed based on the measured rock deformations between surface and the anchoring point of the reinforcement. The rebound rock deformations and the stress increases in the reinforcement can be estimated based on the results of the finite element analysis and experiences in previous field measurements incorporated with considerations of the geologic conditions, rock properties, rock reinforcement and construction procedures.

Jan 1, 1986

By Annan Cook

Cyprus Metals' Sierrita mine is located in the Pima Mining District, Pima County, Arizona (Fig. 1), which is one of the largest known porphyry copper districts. The ore body is part of a large mineralized system that includes Cyprus' adjoining Esperanza mine. The copper and molybdenum grades being mined at Sierrita make it one of the two lowest grade porphyry copper mines in the world Mineral production from the district was first recorded in 1876. Copper from replacement deposits in carbonate rocks and copper¬-lead-zinc from veins in volcanic rocks were mined from several deposits. However, it was not until 1957 that the district commenced to become a major copper producer with the beginning of production from the Pima mine, which was the first open pit operation. Since that time, seven other open pit mines have come into production. Because of the variable copper prices and high operating costs, not all of the mines are operating today. A map of certain outcrops, plutons, and open pits, as well as older underground mining operations, in the Pima district is shown in Fig. 2.

Jan 1, 1991

By T. Brasier, K. Oakes, S. Crabtree, B. Lusk

Destructive wave interference has been studied in theory for many years. In application however, limited information can be found. Recently, circumstances have enabled a multidisciplinary team to utilize electronic detonators and seismograph analysis to create destructive wave interference in an underground production blasting application. Springfield Underground, located in Springfield, MO, in conjunction with Orica, ETI, White Industrial Seismology, and the University of Missouri – Rolla has shown the ability to use destructive wave interference in underground blasting to reduce ground vibrations directly above. In order to develop additional reserves a reduction in vibration levels was necessary for tunneling under the Springfield Municipal Water Supply. The paper discusses the process by which the reduction in vibration was achieved in practice, as well as a technical explanation of the effects of destructive wave interference and sacrificial holes.

Jan 1, 2006

By Kenton E. McElhattan

Financial analysts have often called National Mine Service Co. the only "pure play" company to the mining industry, meaning that an investment in NMS is an investment in the mining industry. As a leading manufacturer and supplier to the industry, National Mine Service does enjoy a close and direct relationship with mining. It is the only independent company that offers products and services that include mining machinery, health, safety, instrumentation, mine supplies, and reconditioning services for hydraulics, electronics, and machinery. But what is a positive relationship in periods of economic upturn can be eauallv as negative during the downturns. In fact, National Mine Service has felt the resounding blows of the current recession in the mining industry. Two-Fold Strategy Rising unemployment, corporate losses, bankruptcies, and mine closings in particular have directly affected NMS. But the company embarked on a strategy several years ago that included a two-fold approach to becoming less dependent upon the vagaries of the US coal industry. One strategy was to develop additional products and services for other mineral industries such as potash, trona, and salt and, where possible, apply the technology developed for the mining industry to industrial markets. The other strategy was to become a more international company. The objective was to make export sales a minimum of 10% of total corporate sales. Even today, NMS believes this is a good strategy as opposed to diversifying because its expertise is in mining, not in other areas. A review of NMS's fiscal 1982 annual report indicates that the company's strategy did begin to pay off. 1982 was a turnaround

Jan 2, 1983

By Robert S. Saunders

Cast iron tubbing for two centuries was the only practical watertight shaft lining for deep waterbearing formations. However, since World War II composite welded steel and concrete lining has gained favor and today is often preferred. While tubbing may not be applicable in all cases, a good argument can still be made for this time-honored method. Watertight linings are complex structures designed to withstand both hydrostatic fluid pressure, non-uniform loading created by ground forces, and vertical bending caused by subsidence. Resulting stresses in the lining can be high. To date linings have been designed that withstand hydrostatic pressures as high as 1,500 psi. Watertight linings must be robust, constructed of the highest quality materials, and manufactured and installed with precision. Therefore, such linings are expensive. Today's ductile cast iron tubbing is greatly superior to gray iron formerly used for tubbing, and is stronger, and more resistant to corrosion than welded steel lining. Tubbing, unlike steel linings, can be installed in wet conditions and used to control water inflow and stabilize unconsolidated ground as the shaft is deepened. Steel lining requires absolutely dry conditions for welding, which often necessitates expensive ground freezing and a primary lining.

Jan 1, 1985

By Randall C. Divito, Craig R. Eckdahl, Bruce D. Wagener, Joseph Klejwa

The existing Central City Tunnel was built primarily in the 1930s with a small portion as old as the 1880s. It conveys stormwater in downtown Minneapolis. It is a 4,400-ft long tunnel located 80 feet underground. The Central City Tunnel has experienced surcharging and surface overflows during heavy rainfall events. This paper presents the details of tunnel and shaft design for the new Central City Parallel Tunnel to mitigate the overflows. The design considered hydraulics and geotechnical engineering for the structural geologic conditions including the weak Saint Peter Sandstone and overlying strong Platteville Limestone. Ground conditions resulted in tunnel designs including large flat-back box tunnels and unique cathedral-shaped tunnel sections.

Jun 13, 2023

By Rebecca A. Miller, Terry M. Hertel

In-pit identification of neutral waste rock at the Zortman and Landusky minesites in Montana, by visual and chemical analy­ses, will assist in proper segregation and placement of rock so that soil and water resources can be protected. The use of too few or very general segregation criteria to identify neutral waste rock can result in ineffective waste rock segregation. Conversely, the use of overly restrictive criteria can result in the unnecessary loss of valuable reclamation material that would otherwise have to be mined elsewhere and hauled to the site. Recognition of nonre­active materials can be accomplished on a site specific basis with the use of visual observation and simple chemical analyses. The choice of chemical parameters used to analyze rock samples is constrained by the length of time needed to conduct the test. These analyses must require no more than 24 hours to complete so mining can proceed without delay. Limits set for the chosen parameters must be reasonable and defensible. To achieve these objectives over one thousand samples were collected at the Zortman and Landusky minesites and clas­sified by rock type, total sulfur content, paste pH, and net neu­tralizing potential (NNP). In addition, over 22 humidity cell kinetic tests were conducted to help corroborate static results for waste rock. Another 8 humidity cells were configured in series to test waste rock blending and waste rock/limestone capping alternatives as mitigation for acid rock drainage. Leachates were analyzed for pH, conductivity, alkalinity, acidity, sulfate, Al, Cd, Cu, Fe, Mn, Zn, Mg, and Cr in some cases. Petrographic analysis, as well as total sulfur content, paste pH, and static and kinetic test results identified three geochem­ically different waste rock groups: 1) Archean amphibolite gneiss and Paleozoic carbonates and shales, 2) Tertiary syenite porphyry, and 3) other less abundant Tertiary igneous and Archean metamorphic rocks.

Jan 1, 1996