Search Documents

By Robin Dill, Wei Song, Andrew Perham, Leo Martin

"AECOM completed a subsurface exploration program for an 18-foot diameter, approximately 4-mile long rock tunnel project in Hartford, CT. The tunnel crosses the regional geologic trend through the middle of a sedimentary basin, passing through four separate rock formations, including two volcanic flows. Faulting is prevalent, with at least 15 faults encountered during the site investigation. Severe artesian flows were also experienced in several of the borings, requiring highly specialized drilling equipment. Sixty-two borings and associated testing were performed to characterize the structural geology, hydrogeology, rock properties and ground conditions. A phased program was carefully planned and implemented with participation of geotechnical and geologic specialists, with thoughtful evaluation along the way to react to the ground conditions encountered, and make appropriate refinements. This paper will discuss the subsurface program details; the integrated efforts used to effectively characterize the ground; and will summarize the final characterization presented in the GBR. PROJECT DESCRIPTION The South Tunnel Conveyance and Storage Tunnel project is part of the Metropolitan District (MDC’s) Long Term Control Plan to address discharges to various water bodies throughout the greater Hartford area. This program includes a main conveyance and storage tunnel; a tunnel boring machine (TBM) launch shaft and retrieval shaft; adit tunnels with associated drop shafts and connection structures; consolidation conduits and manholes; and a tunnel pump station (TPS) at the downstream end of the main conveyance tunnel. AECOM is serving as prime designer for the MDC on this project. The main conveyance tunnel (hereinafter referred to as the “South Tunnel”) will be a deep rock tunnel with an invert depth of approximately 180 feet at its downstream end and approximately 218 feet at the TBM retrieval shaft. The tunnel will have a finished diameter of 18 feet. The tunnel will rise in grade at a slope of 0.1 percent to its upstream end. Total invert depth along the deep tunnel alignment ranges from about 180 ft. to as high as 320 feet. The total length of the tunnel will be 21,754 feet. The South Tunnel will be constructed using a shielded TBM and fully lined with pre-cast concrete segments."

Jan 1, 2016

By Alain Broussaud, Guy Fourniguet, Jacques Franck, Pierre Conil

Steady-state simulation is now in current use to assist mineral processing plant design and optimization. However, the reliability of results generated by simulators has not until now been seriously investigated. A simulator supervision algorithm was designed and programmed to study both the influence of the reliability of experimental data on the accuracy of unit operation model calibration, and the influence of unit operation model accuracy on the results of direct plant simulations. An application to a grinding flotation plant is described and discussed. The approach may open the way to the quantitative analysis of the risks taken in mineral processing projects, which would be similar to the application of geostatistics to mining projects.

Jan 1, 1990

By P. Venkatasubramanian

The selection of a mining method for a mineral deposit is a complex decision problem. Human judgment, based on experience with mineral deposits and geologic conditions, remains the single most important input of the decision-making technique. If the use of artificial intelligence, in particular the developments in expert systems, is taken to its logical conclusion, the experience of the domain experts could be incorporated into a decision-support expert system. A knowledge-based decision support system for mining method selection for ore deposits has been designed whereby the domain knowledge is represented as production rules and organized in a semantic tree representation. This model is written in the PROLOG language. While the verification difficulties of expert systems models are recognized, an example of the model's decision on the mining method for a given ore body is presented and shown to be consistent with the decision made by human experts. In addition, plans, for further verification of the model are delineated.

Jan 1, 1992

Crushing and grinding activity in 1989 followed the rapid pace of the mineral industry. Use of existing installations, demand for expanded capacity, and implementation of entirely new operations contributed to a high level of activity. At the 1989 SME-AIME Annual Meeting in Las Vegas, NV, the crushing and grinding session focused on wear materials in crushers and mills. Another session joined the process control group in its simulation-modeling and control of crushing and grinding circuits. Both sessions addressed the optimization in operating effectiveness. Specific subjects covered grinding media wear of forged and cast grinding balls and rubber lined mill liner wear. Also, the Semi Autogenous Grinding (SAG) Mill Conference in Vancouver in September 1989 provided a valuable update on the progress of SAG operations in recent years. Operationally, gold grinding and roasting circuits were implemented in 1989. Freeport McMoRan Gold started up two operations in Nevada. Two other circuits, both using SAG mills, are scheduled to start in 1990. These will be in Nevada and British Columbia. Elsewhere in gold, additional capacity continues to be brought onstream, both domestically and worldwide. In copper, expansions continue to call on additional crushing and grinding units. The unrest at Bougainville in Papua New Guinea has fueled a continued, strong demand for comminution in the copper sector. Specific equipment installed or started in 1989 included the ac variable frequency drive SAG mills in Australia, Alaska, and Papua New Guinea. Also, the gearless drive SAG mill in Chile provides tremendous flexibility in terms of mill speed. The trend toward moveable in-pit crushers continues -even at established operations.

Jan 1, 1990

By John J. Gillis

There is an ongoing battle to gain general acceptance of fossil fuel byproducts as safe, economical and useful agro-industrial materials. Despite that, the US ash industry is witnessing a steady growth in the volume of coal burned, along with the production of greatly refined, higher-quality ash particulates. There are two principal reasons for this. Economics have caused an increasing number of US electric utilities to convert from oil-burning to coal-burning. And the Federal government has tightened specifications on fly/bottom ash production quality. Hence, it must be noted that new and more stringent Federal regulations were implemented in 1980. The resultant ash particulates are finer, more compact, and less heavy than in previous years. Additionally, the first shift from oil to coal in the US was initiated in December, 1979 by the New England Power Co. in Massachusetts. Coal is the most widely-distributed fuel in the US. And it is found in 38 states. The wide availability of this fossil fuel and its general cost-efficiency, coupled with the undaunted move of US electric utilities toward nuclear power, are major factors affecting the current statistics on ash generation (65.4 x 106 million tons). Interest in the use of coal in power plants is creating a unique ash disposal and use situation for ash producers as well as the Federal government. There are growing quantities of fly/bottom ash residue. Ash producers must decide how this byproduct can be dealt with effectively and profitably. At the same time, government agencies such as the US Environmental Protection Agency (EPA), are commissioned by Congress to assure that solid, liquid, or gaseous material released into the environment is not harmful or offensive to human health and the environment. Additionally, the Federal government is often responsible for establishing and enforcing guidelines and standards governing the use of recycled materials. Several standards and guidelines governing the properties and use of ash in the US have been established by governmental agencies as well as by the ash industry itself. Of these, some have been developed for ash use by a specific federal agency. Others apply to the entire industry. The following is a brief identification of the major specifications for fossil fuel ash: • US Corps of Engineers - These specifications were first established in 1957. They delineate the physical and chemical requirement for pozzolans used in mass concrete. These specifications applied only to Corps of Engineers' concrete construction projects for locks, dams, and other mass concrete projects until 1977. At that time, a joint effort between the American Society for Testing and Materials and the Federal government produced a modified specification that is now generally applied. The Corps of Engineers' ash, however, retained certain aspects of its specifications for its own use, particularly in the area of handling and shipping fly ash to its own projects. Prior to transporting the fly ash to the corps, all potential sources for the ash must be inspected and approved as a supply source. All silos must be filled, sealed, and tested before the ash is released for shipment. The normal test period for the ash is seven days, although several testings may require up to 28 days. Once the fly ash has been released, it can only be shipped to US Corps of Engineers' projects. All shipments are made with a government inspector present during loading. After a truck or railcar is loaded, the silo is resealed until the next shipment. This procedure requires three silos, and a minimum of 454 t (500 st) each should be considered for each storage unit. All silos are strictly committed to Corps of Engineers' use and are not available for other commercial shipments. • US Bureau of Standards - This Federal agency maintains a standard testing sample of nearly every product used in the US. The accuracy of the fly ash chemical analysis is measured by a regular cement and concrete reference laboratory (CCRL) inspection and based on test results from a standard sample of cement. • US Bureau of Reclamation - This agency pioneered several projects using fly ash and required Federal Standard Certification for pozzolans. • American Society for Testing and Materials (ASTM) - This nongovernmental organization began preparing standards for fly ash sold and used in the cement and concrete industry in 1947, at the urging of ash marketing firms. Current standards define chemical and physical requirements and is entitled, "Fly Ash and Raw or Calcined Natural Pozzolan for Use as a Mineral Admixture in Portland Cement Concrete (C 618-80)." • State Highway Specifications - Led by Alabama, many states are moving toward permitting - and in some cases requiring-the use of fly ash in portland cement concrete and with lime for base stabilization projects for roads and highways. • Federal Aviation Administration (FAA) - The FAA acts in an advisory capacity. It has final approval on design specifications for airport construction projects. The agency has established a set of guidelines permitting the use of fly ash, and has approved several fly-ash-specific designs. The most current FAA fly ash projects

Jan 8, 1984

By H. S. Soto

The exact reasons that explain the low recoveries of coarse particles in conventional flotation machines are not clear. Being a concern for only a couple of mineral industries comparatively very few studies have been devoted to the problem of coarse particle flotation. Coarse particles flotation is particularly important in potash and phosphate beneficiation. Potash concentrates with particles larger than 1-2 mm do not require additional compaction or recrystallization and receive a premium price. However, recovery of this size particle in conventional flotation cells is very low, and therefore, the coarse floation tailings have to be reground and refloated to produce, at a higher cost, a less desirable concentrate. In phosphate beneficiation deslimed coarse ore (nominally l4x35 or l6x35 mesh) is normally treated separatedly from the finer (35x150 mesh) ore. Concentration by conventional froth flotation alone yields very low recoveries, and therefore, additional processes such as agglomerate flotation in tables spirals and belt conveyors have to be used ( Moudgil and Barnett 1979). Fatty acids and fuel oil used in phosphate flotation have a moderate level of selectivity but considerable amounts of sand report to the froth product, thus concentrates have to be further upgraded by a double flotation process. Concentrates from the anionic circuit are scrubbed in an acidic media to desorb the collectors and then refloated in a cationic circuit to eliminate the fine silica (Lawver et.al. 1978). In this paper the reasons that explain the low recovery of coarse particles in conventional flotation are discussed. A flotation column modified according to the main conclusions of this discussion is tested with two coarse phosphate samples.

Jan 1, 1989

By H. Burton

"The selection of the ultimate pit shell has a major impact on the overall value of a mining project. The size and shape of this pit drives the selection of pushbacks, equipment, and project strategy, each of which are significant in their own right. Optimization of the ultimate pit shape is typically done using the Lerchs-Grossman algorithm with inputs of production costs, commodity prices, and pit slope constraints. This method ensures that every tonne mined is profitable but does not take into consideration the timing of material release. This timing is essential when calculating the Net Present Value (NPV) of the project, which is one of the most popular metrics for valuing deposits. Often, when the mining schedule and discounting are applied, material that was considered profitable before discounting becomes sterilized. The objective of this paper is to show the methodology for improving ultimate pit selection by considering the production schedule. Application of this technique will generally produce a smaller and higher-value pit than using the Lerchs-Grossman algorithm alone. INTRODUCTION The Lerchs-Grossman Algorithm was developed in the 1960s and exists to produce a mathematically optimum shape for open pit mines (1). This algorithm is now an industry leading technique for producing the theoretical optimum shape for open pits and is used in many popular pit optimization and strategic planning software packages, such as GEOVIA’s Whittle. The Lerchs-Grossman (LG) Algorithm is based on graph theory and optimizes on the assumption of non-discounted cash flows. This produces a mathematically optimum shape, but does not consider the timing with which the material will be removed from the ground. This is an important consideration, given that one of the most popular metrics for evaluating mining projects is Net Present Value (NPV) (2), which relies on the timing of cash flows as a major differentiator between options. This paper will discuss issues inherent in the use of ultimate pit selection based on undiscounted economic factors and illustrate a simple technique in Whittle, a leading software package, which can be used to improve the NPV of projects."

Jan 1, 2015

By R. Zaragoza M., M. C. Fuerstenau, C. O. Nebo, J. R. Kelso

The rate of adsorption of gold cyanide on activated charcoal was examined as a function of charcoal concentration and size, temperature, initial gold concentration, pH, and initial concentration of gold on the charcoal. Rate was found to be proportional to temperature, concentration of charcoal and initial gold concentration on charcoal, and to the inverse of charcoal particle size squared. An activation energy of 2.0 kcal/mol was determined

Jan 1, 1988

By M. U. Khan, A. D. S. Gillies

"Diesel exhaust is a major cause of large number of occupational diseases. Acute and continuous exposure to Diesel Particulate Matter (DPM) can cause numerous health issues including respiratory disease, reduced lung capacity, heart disease etc. The National Institute of Occupational Safety and Health (NIOSH) and the International Agency for Research on Cancer (IARC) consider diesel engine exhaust as carcinogenic. In large underground metal and nonmetal mining operations, regulatory compliance regarding miner’s exposure to airborne particles especially DPM is a big challenge. Complex mine networks add more difficulties in controlling DPM. MSHA relies on the NIOSH 5040 method for DPM compliance. The NIOSH 5040 method is a shift average based method which inherits some limitations. Due to these inherent limitations of the NIOSH 5040 method the concept of real-time DPM monitoring is promoted in the mining industry. Several real-time DPM monitors have been used by the researchers and efforts still continues to improve their measuring techniques and understanding. Real-time monitoring of DPM is vital to gain understanding of rapid changes in the mine atmosphere. The current study highlights the advancement in real-time DPM monitoring and mainly covers a review of several studies in which DPM concentrations were measured by utilizing real-time DPM monitors. INTRODUCTION Ventilation of underground mines is an important aspect of mining operations. Mining is a continuous activity and the ventilation networks in modern mines change with extended developments. Proper understanding of the ventilation network is a key design factor of an optimum mine ventilation plan. An important task of underground mine ventilation engineers is to provide clean air with sufficient quantity to the underground miners (Khan M. U. and Gillies A.D.S. 2015). The amount of fresh air supplied to the mine should be adequate to dilute the concentrations of contaminants present in the mine atmosphere. In the United States it is estimated that diesel powered equipment is used in thousands of mining operations (Stephenson D. J. et al. 2006). Use of diesel powered equipment is an attractive option in underground mines due to its several advantages over other available alternates. Diesel engines are rugged, dependable and fuel efficient (McKinnon 1999). It is common for diesel engines in heavy duty trucks to have a life of 1.6 million kilometers (McKinnon 1999). Looking at the developments in other energy alternatives, it can be assumed that the underground mining industry will maintain its reliance on diesel powered equipment (Anon 2001). DPM is an important source of mine air contamination in many non-gassy underground mines (Khan M. U. and Gillies A.D.S. 2015). Diesel exhaust is harmful for humans. Acute and continuous exposure to diesel exhaust concentrations can cause several health issues. Some of the health diseases caused by DPM exposure are respiratory diseases, reduced lung capacity, heart disease, and lung cancer (National Research Council. 1981, Mine Safety. 2005). In addition, NIOSH regards diesel exhaust as “potential carcinogen” (Centers for Disease Control 1988) and IARC has declared that “diesel engine exhaust is carcinogenic to humans” (IARC 2012). NIOSH has also declared that the reductions in DPM exposure would reduce cancer risks (Centers for Disease Control 1988)."

Jan 1, 2016

By T. Harris

Exports of crude gypsum from Mexico currently comprise about 60% of all domestic shipments, and about 25% of the imported material consumed in the U.S. wallboard industry. However, of growing importance are the domestic markets for calcined gypsum in Mexico including building plasters and wallboard, which account for 55% of the internal demand for natural mined material. This paper will examine the current trends in the production and trade of natural mined gypsum in Mexico and North America and the opportunities and threats that are facing existing and new suppliers in this changing market.

Jan 1, 1996

By Yoginder P. Chugh

The Department of Energy is presently sponsoring the development of automated miner-bolter machines in an effort to increase production and productivity in the continuous room-and-pillar mining sections. This study is concerned with the production potential of these machines in three different mine layouts. The Underground Material Handling Simulation (UGMHS) computer model was utilized in the study. The effect of variables such as bolt installation delay, shuttle car capacity, and equipment availability on production are analyzed.

Jan 1, 1979

By Dirk Bleazard

Barrick Goldstrike Mines is improving the reliability of mining and processing equipment through the use of failure analysis and condition monitoring activities. Program results include an increase in equipment capacity and an overall reduction in operating costs. Identifying equipment failure modes and developing associated capital asset management practices can minimize failure consequences. Successful programs have included alterations to management practices, equipment modifications, and/or the implementation of condition monitoring programs. By controlling or minimizing the effects of incipient equipment failures, corrective actions can be taken earlier in the failure cycle. This results in an associated reduction to repair costs and equipment down time. Mining companies invest in their capital assets to provide the capacity necessary to meet operational needs. Over time, functional failures occur that reduce this productive capacity. Diagnostic technologies now exist that allow the condition of equipment to be monitored. Early response to this information minimizes the effects of functional failures and restores equipment re- liability. Reliability is a performance indicator of overall equipment condition. It is most often expressed in terms of mean time between failures. When the established objectives of a capital asset management program include the maximization of this failure interval, trailing indicators, such as availability and operating cost improve. The probability of equipment failure is influenced by engineering design and operating conditions. The performance level resulting from this operating environment is expressed as "inherent reliability." Without maintenance intervention, equipment will ultimately fail to perform its intended function and become less reliable. Therefore, maintenance must be managed as the supplier of reliable operational capacity. Maintenance can only supply equipment performance that approaches the level of inherent reliability. Actually achieving inherent reliability requires that all maintenance decisions are made at the economically optimal time. Enhancing performance levels beyond inherent reliability can only be achieved by altering operating conditions or practices or through physical equipment modifications. An evolution in maintenance management philosophy has been under way since the beginning of the industrial revolution. As equipment has become more sophisticated, so have maintenance practices. At the beginning of the industrial age, equipment tended to be over designed and slow moving. The first maintenance philosophy was one of reactive maintenance. Maintenance intervals were dictated by the operational status of the equipment. As a result, production interruptions were common and capacity needs were met through an investment in redundant capital assets.

Jan 1, 1998

By A. Anttila, S. Persson

The grinding mill is probably the most common unit operation in mineral processing. There is, however, much that can still be done in the way of optimization. This paper discusses the results of a well-controlled pilot-scale test in which the performance of a tumbling mill equipped with a conventional rubber lining and lifter bars was compared to a tumbling mill equipped with a smooth rubber lining of the magnetic type. The results indicate that the smooth lining is about 14% more effective with respect to energy consumption. By optimizing the size of the grinding media, the mill capacity can be increased in many grinding operations. In this specific case, grinding with a -20-mm ball charge required 26% less grinding energy than grinding with a -30-mm ball charge. The energy savings can, in most cases, be converted to an increase in capacity. The wear of the grinding media is difficult to assess over a short test period, but the results suggest that the wear is somewhat less when a smooth lining is used. A determination of the wear of the linings was not included in this study, but it is generally accepted that the use of magnetic linings reduces the lining costs dramatically. Computer simulation using the Millsoft code developed by Mishra et al. confirms and explains the increased effectiveness of comminution when a smooth lining and smaller grinding balls are used.

Jan 1, 2000

By M. G. Ayat, J. W. Leonard

Introduction Coal preparation plants are continuously losing clean coal in their refuse and contaminating their clean coal product with impurities. This is due to the lack of a system by which the immediate efficiency of the cleaning operation can be determined at any given time. Moreover, the advantage of developing tagging/ tracing techniques would be a reduction in the time and money spent in evaluating the performance of advanced cleaning techniques. Currently, conventional sampling and testing, on-line analyses, and computer information systems are the major tools with which engineers analyze and control the efficiency of processing plants. Conventional sampling and testing is an effective analysis technique but it is slow. On-line analysis provides information on quality parameters rapidly, but these parameters do not provide all of the necessary information. The use of tagged particles in coal preparation plants may provide the necessary link between diagnosis and the application of computers to process control. In this work, a novel technique that uses tagged particles to generate partition data is presented (Leonard et al., 1982). Individually prepared tagged particles are added to the feed and detected in the product or refuse port of specific gravity based processes. Providing that a computer can interpret the output of a detection device and trace particles with predetermined physical properties through the coal preparation plant and that the trace particles actually represent desired raw material, sufficient partition data can be provided for computer analyses and control of processing efficiency. Coal tagging technique The use of tagged particles in coal preparation operations are in the early stages of development. Though there is a brief history of particle tracing in the mineral processing industry (Gardner et al., 1986; Foreman and Amundson, 1976; Poston et al., 1962), the concept has not yet been applied to the analysis and control of processing plant operations. Several methods for tagging coal particles have been identified. These include magnetic, radioactive, and fluorescent techniques. As far as the magnetic tagging of coal particles is concerned, a method has been developed to manufacture synthetic magnetic particles of various sizes and specific gravities. Ideally the synthetic particles would have identical size and density as the coal particles being separated.

Jan 1, 1988

By Raphael Mourad, Colin R. Phillips

Fluorescence, radioluminescence, phosphorescence and thermoluminescence in TLD 100 and 700 are discussed and compared. The energy budget in thermoluminescent material is presented in general terms. Results of measurements of radioluminescence, phosphorescence and thermoluminescence in LiF:Mg irradiated with [a] radiation, using simple facilities, are presented. The calculated energy budget in the exposed chips using [a] radiation is compared to published data using [y] irradiation.

Jan 1, 1981

By R. Mulyanto, M. Siray, A. Parhusip, F. Hartono

"PT Freeport Indonesia is preparing the Deep Mill Level Zone (DMLZ) mine to be the successor of the currently operating Deep Ore Zone (DOZ) mine. The DMLZ is block cave mine situated 500 m below the DOZ mine and approximately 1600 m depth from surface. Both of the block caving mines require draw point construction in the extraction level to extract the ore from caved area above. Learning from the experience in DOZ, the construction & maintenance of draw points in the production panels is a significant challenge in supporting consistent production.The average DOZ draw point construction duration is approximately 46 shifts per draw point. The time frame for construction is dependent on several variables; availability of the conventional forming system, material availability, and development tolerances. The repair of concrete floors and lintel sets causes production downtime. Reviewing the old DOZ draw point design, there is an opportunity to increase constructability, durability, and reliability of DMLZ draw points. This paper discusses how the DMLZ has improved draw point construction productivity and is on track to significantly reduce costs whilst increasing the quality by using the Six Sigma Improvement Method.Introduction The DMLZ Mine is part of the PT. Freeport Indonesia (PTFI) future Expansion to its underground mining complexes. It is the fourth vertical lift in the East Ertsberg Skarn System (EESS) deposit (Figure 1).Currently, it is under development phase.The DMLZ mine will be a block cave mine using an advanced undercutting method. The DMLZ extraction level will be approximately 1,600 meters below the surface on the 2570 level with column heights of roughly 500 m. The Undercut is on 2590 level, some 20 meters above the extraction level."

Jan 1, 2016

By G. Pierson

Explanations for commodity price levels (or movements) commonly focus on the fundamentals of supply and demand otherwise they are simply assigned to speculative activity. Comparisons of metal-price histories to monetary and other economic data support the argument that the supply of and demand for money are no less important in the determination of price than are the supply and demand of the commodity itself. That these relationships should exist is evident in the price identity and they are consistent with monetary theory. The patterns developed have limited usefulness as predictors, but their recognition is essential for the construction of price scenarios for planning purposes.

Jan 1, 1998

By C. L. Schneider, R. P. King

Size distributions and liberation spectra were measured in samples taken from 10 streams in a taconite milling circuit under normal operating conditions. The size distributions were deter- mined by sieving and the liberation spectra by image analysis using the linear-intercept method with proper stereological correction. The measured data were used to validate a simulation of the milling circuit using MODSIM which included the calculation of both size distributions and liberation spectra. Both the measured data and the simulator showed that liberated magnetite was returned to the mill in the cyclone underflow. The simulation will be used to improve the economic performance of the plant.

Jan 1, 1995

By M. Rossi

The use of service variables in geostatistics (grade-thickness) is common in industry when developing block grade models and geologic resource estimates. This is particularly true in the case of sedimentary and stratabound-type deposits. The approach has proven merits when assessing ore reserves. However, there are cases where its application for preliminary data analysis produces biased estimates. One such case is encountered in uranium disequilibrium studies. This paper demonstrates the inadequacy of service variables when performing uranium disequilibrium studies. Disequilibrium analysis is a necessary preprocessing step when radiation counts are used as raw data to calculate uranium reserves. Typically, a probe is used to obtain the gamma counts from open drill holes. These counts are then regressed (and corrected) against chemical assays obtained from core samples. During this process the grade-thickness variable produces an optimistic image of the relationship between probe grades and chemical (true) grades, causing overestimation of the final geologic resource. The problem is analyzed through a case study.

Jan 1, 1993

By David J. Dyet

Computer applications in the past five to seven years have become a typical and necessary practice in most modern geological offices. Manual calculations, interpretations and plotting of data can be, at times, quite tedious, inefficient and lacking in ac- curacy. The introduction of geostatistical and geological software can eliminate these problems. Computer applications in the uranium industry are not new; however, they are constantly being developed. A variety of soft- ware programs are available. Generally, these programs support most geological and geostatiscal applications in uranium mines. The Rabbit Lake Operation - Eagle Point mine in Northern Saskatchewan is a high grade mine, as one such case. Computer applications at the Eagle Point mine have been a mainstay in the geology department, since the mine's collaring in 1991. This paper presents a discussion on descriptions of programs, operations and applications of computers. It also explains and de- scribes the radiometric equipment used at Eagle Point. This pa- per will demonstrate how, by using computer systems, mine site information flows reliably with the involvement of computers.

Jan 1, 1996