Search Documents

By Timothy D. Gardner, Christopher Mark

Coal mines in the Illinois Basin have not engaged in pillar recovery for many decades. In large part, this is due to the exceptionally weak nature of much of the roof in the region. But, as room-and-pillar mining is conducted at greater depths, and larger pillars become necessary, recovering them becomes more attractive. Recently a western Kentucky coal mine became the first in recent times to successfully employ full pillar recovery. This paper describes the many challenges that were overcome during the process. From the beginning, the focus was on protecting the miners from roof instability, using cable bolts, mesh, mobile roof supports (MRS), and engineered final stumps. Two short test panels were extracted first, and the results were used to adjust the support pattern and mining sequence. Further adjustments were made based on subsequent experience. To date, seven panels have been recovered without a ground fall injury.

Jul 1, 2023

By C. I. Wilmot, A. Sass, J. VanDeBeuken

Introduction This chapter addresses the need for operation manuals, presents an outline as a guide for writing the manual, discusses who should write the manual, suggests how it is implemented and gives tips to potential manual writers. Theory & Purpose of Operating Manuals The primary objective of the operating manual is to provide every operator the benefit of a uniform minimum level of training. This training is not only critical to the safety and efficiency of every employee, but also provides a basis for incorporating future operational improvements into standard and emergency procedures. The manual promotes safety through- out and additionally has a special section devoted to safety. The operator should be able to find information on chemical and physical hazards as well as be exposed to safety procedures for such items as motor lockouts and tank entries. The operating manual will usually reference a separate safety manual or incorporate parts of the safety manual. Safety is also promoted through standardized procedures for operation of equipment. Standardized operation is the second most important reason for the writing of manuals. If equipment is started, operated, and shut down in a consistent manner, then operational efficiency should be maximized. If it is not, then the procedure is adjusted until it is. The experience of many can be condensed into set responses for start up, shutdown, steady state operations, and upsets. Implicit with the standardized operation objective is a minimum level of training the operator will receive by thorough familiarization with the manual. The ability to know the contents of the manual is a basic requirement for operator status. The operating manual serves as a basis for a training program both at the start of the new plant and as new operators are hired or promoted into the job. The operating manual is a collection of at least part of the knowledge that "key people" own and will cushion the loss of key personnel for whatever reason. The manual can only fulfill these lofty goals by being a dynamic document. Manuals must change as equipment is modified and superior techniques evolve. To be effective they must be periodically updated, so word processors and reproduction

Jan 1, 1986

By J. E. Lees

Advanced remote sensing can be a powerful new information tool to help private and public entities make better environmental and resource management decisions. However, some regulated entities are reluctant to develop or use this tool because of their concerns that it will lead to increased risks and costs of environmental legal liability. They fear that new ways of monitoring the environment will increase liability, undermine existing enforcement agreements, reopen compliance agreements, and generally provide a competitive disadvantage to early adopters by accelerating environmental cleanup costs. Others counter that the increased risks are marginal, and that several advantages outweigh these risks, including the opportunity to more effectively manage environmental operations, target and set priorities, measure and track management and compliance effectiveness, provide more defensible environmental assessments and baseline conditions, make and defend optimal siting decisions, and avoid or resolve environmental disputes. This paper offers strategic advice on ways regulated entities can enjoy the benefits of these powerful new information tools while mitigating down-side legal and compliance risks as much as possible.

Jan 1, 1999

By Frank Hagar, George M. L. Robinson

NTRODUCTION The Resource Conservation and Recovery Act and CERCLA (SUPERFUND), in many instances, has had an adverse economic impact on the hardrock mining industry. Over the last few years, many abandoned and active mining operations have been added to the Environmental Protection Agency (EPA) National Priority List (NPL) . When the property is placed on the NPL the operator or EPA is required to conduct extensive environmental assessments to determine if historical mining practices have degraded the existing environmental. If degradation has or will continue, the responsible party is required to implement appropriate remedial action plans. If a responsible party is not identified, the EPA implements a cleanup program. Experience has demonstrated abandoned and active mining operations are subject to RCRA, and possibly Super- fund, if the mine has not adopted appropriate hazardous waste disposal management procedures. If off-site contamination has occurred, the operator will be required to mitigate the impacts and will be required to adopt additional procedures to minimize future impacts. Since the passage of RCRA and Super- fund, many mining operators are adopting management procedures to monitor and inventory hazardous sub- stances and wastes generated, stored and disposed on site. Many operators are in a difficult position because ore, waste rock, process chemicals or other solid waste, in many instances, can be classified as hazardous waste. If the process or other solid waste is deemed to have the characteristics of a hazardous waste, the operator can inventory and adopt appropriate, in- expensive management procedures. However, if the ore or waste rock has hazardous waste characteristics, in- expensive control technologies are impossible to implement. Since existing statutes and regulations require hazardous waste control, the operator will be required to inventory, characterize and monitor all aspects of the mining operations including but not limited to exploration, mining, ore processing and waste disposal. During this process, geological, geotechnical, geochemical, waste and ore volumes, and process materials must be tracked throughout the mining process. To accomplish this task, the most cost effective method to maintain documented and accurate records, is through the implementation of an integrated database management system. The database management system can be used to model and simulate the entire mining operation and if necessary, used to predict whether the operation is in compliance with existing regulations. The developed database can also be used to operating optimize mining and disposal costs.

Jan 1, 1987

By K. C. Vories, C. D. Elifrits, F. F. Haston

The required reclamation of land disturbed by surface coal mining often results in the creation of some oversteepened slopes that are prone to rapid erosion and sediment production. This natural activity on such slopes is not desirable nor allowed under current regulations. Experience has shown that novel approaches must be devised to address the problem. Research conducted on field sites in Missouri has indicated that construction, during the reclamation and grading processes, of a man-made drainage system will control the erosion. The drainage system must replicate or exceed the natural system in terms of drainage density and channel frequency. Basic design considerations are summarized in this paper, and field results are shown.

Jan 1, 1987

By Colin M. Kelly

The Loveridge Mine, located near Fairmont, West Virginia, has been mining coal from the Pittsburgh Seam since 1958. As the mine develops its reserves it finds itself with increasingly distant hauls from the operating faces to the preparation plant. Initially, the mine was designed with track haulage. The coal was hauled to an underground rotary dump which fed a slope belt, to the preparation plant. As the haulage distances increased, production delays due to the track system's limitations became severe. To resolve this situation, a complete review of the haulage system was undertaken. Simulations of the present system along with future scenarios were conducted to help management effectively plan the haulage requirements of the mine for the remainder of its life.

Jan 1, 1986

By Greg Joachims

Composition of salt in the Permian Flowerpot Shale in northwest Oklahoma suggests that the salt in this formation was deposited in the early phase of solar evaporation. Brine produced through natural dissolution of the subsurface salt has netted very pure brines, with relatively low concentrations of magnesium salts that should result from late-stage precipitation of salt deposits from sea water. Over the last 100 years, extensive studies of sea- water evaporites, in relation to brine density, have been a topic of discussion. The development of evaporation models has facilitated the increased production and purity of solar salt (salt produced through evaporation of brine by the sun's energy). Conversely, this information can be utilized to gain an understanding of how rock-salt formations were precipitated from sea water by analyzing the elemental constituents of the rock salt and of the resulting brine. By evaluation of well-documented, phase-curve tables of sea-water evaporation, a basic theory can be formulated on how the Flowerpot salt unit was formed.

Jan 1, 1999

By D. W. Boening

Xanthate salts have demonstrated effectiveness as a flotation reagent in the recovery of heavy metals from mining wastewater. However, due to their strong ionic potentials, they are generally toxic to aquatic life. Under ambient environmental conditions, the half¬life of a xanthate is approximately four days. As a soluble salt, xanthates will complex with the metallic ions contained in water and fish. Some researchers have proposed that this complexing may extend the halflife, as well as optimizing the transfer of a given metal from solution across the gill surface. Leakage of xanthate treated wastewater into the surrounding surface waters is the most common route of exposure for aquatic plants, invertebrates and fish. Because this is an emerging mineral-recovery technology, more information is needed regarding xanthate toxicity and environmental fate before environmental impacts can be assessed with any degree of certainty.

Jan 1, 1999

By Denise Herzog, Sukumar Bandopadhyay

This paper presents an application of analytical hierarchy pro- cess (AHP) to predict the ranking of three beneficiation methods for a low grade, bulk gold deposit located in the interior Alaska. Seven criteria (attributes) were used for evaluating each beneficiation method. For each criterion a matrix of pairwise comparison between methods was developed. The normalized eigenvector of each matrix scales the beneficiation methods with regards to that criterion. An overall scale is constructed by weighting the scales of all the criteria. Methodology used also indicates a measure of inconsistency. This measure is useful in identifying possible errors in expressing judgments as well as actual inconsistencies in the judgment themselves. The outcome of the pro- cess is the best or optimum beneficiation method, considering all the necessary objectives, criteria, and alternatives in a single integrated framework.

Jan 1, 1996

By Nobuharu Isago, Atsushi Kusaka, Kosuke Kawata, Dohta Awaji

"The immediate ring closure method, in which the entire periphery of the excavation area is closed immediately with an initial support within a short distance from the excavation face, has been increasingly used in Japan, especially, as one of the most effective countermeasures against difficult ground conditions in conventional tunneling. For reasonable design of this method, the performance requirements for the initial support should be clearly stated. The analysis of construction data of 30 road tunnels and the three-dimensional numerical modeling based on real data suggest that the immediate ring closure stabilizes the tunnel structure and the ground around it because of the inner pressure effect of the initial support, especially, for low ground competence factor and small internal friction angle. Finally, the bending compressive strength and the cross-sectional geometry of the initial support have to be considered in the tunnel design while considering the earth pressure and ground properties. INTRODUCTION Conventional tunneling methods often deal with difficult ground conditions such as soft ground or squeezing ground conditions. The immediate ring closure method, in which the entire periphery of the excavation area is immediately supported within a short distance from the excavation face (Figure 1), has been increasingly used in Japan as one of the most effective countermeasures against difficult ground conditions in conventional tunneling (e.g. Takahashi et al., 2011; Nakaoka et al., 2013). The immediate ring closure method was empirically identified as effective for reducing ground surface subsidence and tunnel deformation. However, the working effects of the method have not been clarified sufficiently. To improve the design of this method, the working effects of this method and the performance requirements for the initial support need to be clarified. The relation between the effect of immediate ring closure and earth cover has been clarified (Mashimo et al., 2008; Awaji et al., 2013),"

Jan 1, 2016

By Jaroslaw Drelich

This report briefly reviews the measurements and interpretation of adhesion forces measured between microscopic probes and substrates having micro- and nanoscaled roughness characteristics that were recently conducted at Michigan Tech using atomic force microscopy. The laboratory study concentrated on both rigid and deformable materials, with the probes larger than the size of roughness features of interacting surfaces. For such systems, a detailed surface characterization in terms of roughness parameters, asperity size and shape, and spacing between asperities, as well as analysis of deformation of materials is required. Analysis of the experimental data can be done with theoretical models, which are suitable for rough surfaces and therefore allows to normalize the measured forces. Alternatively, loading of the probe during adhesion force measurements can be managed properly to control deformations of the nano-scaled surface irregularities. Controlling the deformation reduces and even eliminates the effects of nano-roughness on the probesubstrate contact area, promoting conditions described by the contact mechanics models for the sphere-smooth substrate system.

Jan 1, 2005

By J. S. Y. Wang, R. C. Trautz

To evaluate the potential for water seeping into an underground opening, a 9-m- (30-ft-) long drift was constructed in the unsaturated fractured tuff at Yucca Mountain. Forty seepage tests were performed by releasing finite volumes of water at a constant rate into short test intervals located in boreholes positioned above the drift. The seepage threshold flux, defined as the liquid-release flux at and below which water will not drip into the opening, was determined for 10 test intervals. The seepage data, observations and model results indicate that a seepage threshold exists because a capillary barrier diverts water around the opening.

Jan 1, 2002

By Takashi Sakaguchi, Akira Nakajima

Some attempts were made to recover and remove heavy metal elements, such as uranium, copper and chromium, from aqueous systems by using several phosphate compounds. The phosphorylated derivatives of polysaccharides, chitin phosphate, chitosan phosphate and cellulose phosphate, have high abilities to accumulate heavy metals, such as uranium, copper, manganese, cobalt, cadmium, zinc, nickel and chromium, compared with non-phosphorylated polysaccharides. In order to obtain basic information on the recovery and removal of uranium that may be present in industrial effluents, mine waste water and seawater, the adsorption of uranium by chitin phosphate and chitosan phosphate was investigated in details. The adsorption of uranium by chitin phosphate and chitosan phosphate was much greater than copper, cadmium, manganese, zinc, cobalt, nickel, magnesium and calcium. The adsorption of uranium was very rapid and was affected by pH of the solution, temperature. granule radius and co-existence of carbonate ion. The amounts of uranium adsorbed on the adsorbents increased linearly as the external uranium concentration increased. Uranium adsorbed on chitin phosphate easily desorbed with diluted sodium carbonate solution. On the other hand, uranyl and cobalt ions were separated from each other by using chitin phosphate. Along with these fundamental research, some attempts were made to recover uranium from seawater.

Jan 1, 1993

By F. K. Letowski

Leaching of zinc sulphide concentrate by nitric acid which is simultaneously regenerated by oxygen in the reactive froth has been investigated. The reactive froth was formed by a recycled zinc sulphate electrolyte containing nitric acid, a mixture of gaseous 02 and NOx, entrapped in the foam and particles of the zinc concentrate suspended in the foam. In the reactive froth the multiple regeneration of nitric acid proceeded owing to the encapsulated oxygen and amount of nitric acid used can be considerably lower than in the continuous liquid phase. 93 to 97% of zinc was extracted to a solution containing 30 to 409/1 HNO, during 40 to 60 min of leaching in a batch reactor without regeneration of nitric acid. 50 to 100% of the consumed nitric acid was regenerated during continuous leaching in froth carried out in the ‘flotation column’-type reactor at 80 to 90°C and under pressure of 100 to 200kPa. The rate of HNO, regeneration in the froth was proportional to oxygen pressure and inversely proportional to nitric acid concentration in the froth. A two-stage process flowsheet is proposed. In the first, the reduction stage, removal of nitric acid from the leach solution directed to standard purification and electrolysis is carried out by its reduction to nitric oxide using fresh concentrate in the froth. In the second, the oxidation stage, nitric acid is continuously regenerated by oxygen in the froth.

Jan 1, 1995

By M. A. Bothwell

The purpose of this paper is to describe the methods used to select mill discharge screens, and to outline factors which should be taken into consideration when choosing screens for this application.

Jan 1, 2001

By J. Harrison Daniel

Increasing mechanization of underground mining operations throughout the years has reduced the dependency on large, concentrated working forces. Fewer workers in scattered locations, coupled with the versatility of diesel equipment to load and haul personnel, supplies, and mineral ore, has made diesel equipment attractive in mine feasibility and design studies. The use of the mobile equipment along with higher production or "bulk" mining methods provides for more efficient mineral extraction systems. These systems are expected to become more widespread until long-term research provides a further evolution to more complete automation of underground mining. The U.S. Department of the Interior, Bureau of Mines, has been conducting research to reduce the health and safety hazards posed by increasing use of diesel equipment and the higher power ratings being proposed. The goal is to provide for safe and efficient use of the equipment. The National Institute for Occupational Safety and Health has recommended that diesel exhaust be regarded as a potential occupational carcinogen adding importance to the Bureau's research program. The paper describes advances in engine design, the use of diesels in mining operations, and significant health and safety research accomplishments of the Bureau of Mines. These accomplishments will help assure that diesel equipment remains an option for determining the most efficient system to mine an ore body.

Jan 1, 1989

By Levent Ozdemir

The advantages offered by mechanical mining have been demonstrated in the underground mining of coal, evaporites and other soft minerals. Mechanical mining and the advancements in automation technoloogies have been the principal drivers towards the realization of enhanced productivity in soft rock mining. For past two decades, emphasis has been placed on developing mechanical mining technology for hard rock applications, to achieve similar productivity improvements and cost reductions. The benefits of mechanical mining are numerous, particularly in an industry where market conditions continue to dictate higher production and lower costs while maintaining high safety standards. Other benefits of mechanical mining include reduced ground support and labor requirements and the elimination of blast and diesel fumes. These benefits further make this technology an attractive alternative to drill and blast for hard rock mining. Mechanical mining is conducive to full implementation of remote control and automation technologies that are under development to achieve further productivity and safety improvements in underground mining. Mine development has been the main focus area for mechanical miners by manufacturers and mining companies. Potential applications include ore body access, haulage and ventilation drifts, undercut and exploration drifts. The economic use of this technology in mine production is still considered many years away. It would need a major technological breakthrough that would make mechanical rock fragmentation competitive with the large-scale, low-cost production blasting operations.

Jan 1, 1998

By A. C. Noble

Ore reserves are often less than 30% of the geologic resource estimates initially prepared by exploration geologists. Differences of this magnitude can lead to serious problems in the early valuation of properties when the geologic resource estimates are interpreted to represent ore reserves but are later found to be misleading and gross overstatements of the actual ore tonnages. The geologist can avoid such difficulties by considering the implications of mining, metallurgical recovery and economics early in the project and by using appropriate qualifiers in the resource statement. Examples using typical deposit characteristics are used to demonstrate how the cutoff grade, stripping ratio, dilution, mining extraction and metallurgical recovery affect ore reserve estimations.

Jan 1, 1994

By Youning Li, William J. Drury, Christopher H. Gammons

A demonstration scale, subsurface flow anaerobic wetland was built to treat zinc and other metals in surface drainage near the historic mining center of Butte, MT. Based on three years of continuous monitoring (1996-1998), copper and cadmium were effectively removed year-round, but attenuation of dissolved zinc was dependent on hydraulic residence time (HRT) and bacterial sulfate reduction (BSR) rates. BSR rates decreased in winter months, as did HRT due to the development of thick frost zones in the substrates. An additional problem was the inability of the wetland substrate to completely filter out fine-grained particles of ZnS forming in the anaerobic cells.

Jan 1, 2000

By Edward B. Westphal

One of the purest gypsum deposits in the United States is located in northwest Oklahoma about 90 miles northwest of Oklahoma City. Gypsum beds of the Blaine Formation (Permian) are each 10 to 15 feet thick and 97 to 99 percent pure; they are being quarried by four companies in the area. Most of the stone mined by U.S. Gypsum Company is calcined for the manufacturing of wallboard and special plasters, but some of the crude gypsum is marketed for cement manufacture and for use as soil conditioner. Reclamation of the mined lands at Southard, Oklahoma, has been carried out since 1968, and the company is now involved in a cooperative program of land revegetation to aid in erosion control, provide for wildlife, and for beautification.

Jan 1, 1978