Search Documents

By Felipe Calizaya, Sekhar Bhattacharyya

Mechanized underground mines suffer from noise overexposure. Noise levels are often above the Permissible Exposure Limit (PEL) where underground fans are used. Sound levels in active workings can reach up to 121 A-weighted decibels (dB(A)), especially when fans are not equipped with silencers. Use of silencers seldom ensures PEL. Overexposure of noise induces permanent hearing loss among mine workers. A NIOSH-funded research project and field studies at six coal and non-coal mines revalidated the findings. The University of Utah undertook laboratory studies to reduce fan noise at the source. A new silencer prototype with varying noise dampening material was designed and tested. The silencer and associated extension can be repacked with different dampening materials. The silencer and the extension were used in various configurations. Attempts were also made to simulate field conditions. The tests demonstrated a maximum sound level attenuation of about 14 dB(A) at the fan discharge. A properly designed silencer offers lesser resistance and thereby better fan performance and lower energy cost. The re-packable silencer is more likely to be maintained properly. Lowering of noise level happens in audible frequencies (4000 to 8000 Hz) which are important in A-weighting.

By John Ralston, Gayle E. Morris, Daniel Fornasiero

The interaction of talc with carboxymethyl cellulose, a polymeric depressant currently used in the mining industry, was investigated. adsorption isotherms, infrared spectoscopy and microflotation studies were performed to determine the surface properties of the depressant at the talc-water interface. Solution conditions were varied in ionic strength, pH and the presence of magnesium ions. The adsorption of the anionic polyelectrolyte, carboxymethyl cellulose onto the talc surface was greatly influenced by the solution ionic strength and pH. Limited adsorption, and therefore depression, occurred at high and low ionic strength. Adsorption, and thus talc depression, improved greatly with either increased ionic strength or reduced pH. With the addition of magnesium ions, talc depression was shown to improve considerably. The improved depression is likely to be the result of the formation of a magnesium ion-carboxyl complex.

Jan 1, 1995

By Dennis Ofiara, Paul Zick

Two 8.2 m diameter flood control tunnels are being constructed in the Taylor Shale Formation beneath San Antonio, Texas. These tunnels use precast concrete segments as final lining. This paper describes the features of the segments chosen for this project. The tunnels are being excavated with a hybrid Tunnel Boring Machine. This paper also describes the features of the TBM which make the machine compatible to the type of segments chosen.

Jan 1, 1989

By W. L. Hollinshead

For more effective and cost-saving production in tunnels, the machinery used on construction sites in the future will be equipped with guidance systems combined with working-procedure management systems. This paper describes sensors for these systems and vari¬ous system configurations. A project is described that uses a computerized guidance system on an underground mining machine for guidance and profile control.

Jan 1, 2000

By Trent A. Tempel

In 1989 Newmont Gold company initiated a project to develop a treatment process for higher grade refractory gold ores to be mined from deposits along the Carlin Trend in Nevada. Extensive laboratory and pilot testing have identified a unique whole ore roasting process for oxidizing these ores prior to gold recovery by conventional cyanidation techniques. Subsequent detailed engineering studies by Fluor Daniel evaluated three different dry grinding flowsheets for feed preparation to this roasting circuit. The selected flowsheet will incorporate a two compartment ball mill with an attached drying chamber that is driven by a 11.2 MW (15,000 hp) wrap-around motor.

Jan 1, 1993

By James R. Aggson, Verne E. Hooker, Dennis R. Dolinar

The stability of underground openings and mining systems is closely related to the in situ stress field. This paper presents a short discussion of the three-component borehole deformation gage and overcoring technique which the Bureau of Mines uses to measure in situ stresses, and a summary of stress data that the Bureau has gathered in the process of evaluating ground control problems. Specific ground control problems and stress distributions are discussed as examples.

Jan 1, 1982

By J. D. Pfarr

The Homestake Mine, located in Lead, SD, has been in business for 113 years. Until 10 years ago, conventional mining methods were used to extract ore. Due to complexities in the ore bodies and increasing costs, new technology was introduced to the mine. An integral part of this technology was mechanized cut-and-fill mining. This mining method currently produces about 50% of the annual production and has proven to he safe and economical. As a result, the Homestake Mine remains competitive in today's market.

Jan 1, 1992

By Haia Roffman, Amiram Roffman

A gas company operated more than 100 distribution stations. Mercury filled manometers were used for years in these stations to measure the flow of natural gas through the system. Use and handling of these manometers resulted in mercury spills and ground contamination. To assess the human health and environmental effects of these spills and the need of remediation, it was important to determine mercury specific species present and their concentrations. Soil samples were analyzed for total mercury, methyl mercury, inorganic mercury and elemental mercury. These analyses served as important input in the risk assessment performed for these stations.

Jan 1, 1998

By V. Arad, S. Arad

Besides the conservation and closing activities, an important issue to achieve is the environmental rehabilitation of the mining perimeters, also assuring the continuity and sustainable development of the mining activity in the Jiu Valley. Modifying and depleting the soils by mining works and dumps of mineral waste as a result of coal mining and tailing is one of the important aspects. The paper’s aim is to analyze which are minerals and resources policies of our government and to adopt measures for sustainable development in the coal mining in this region. The measures to reduce the instability risk for the mining works and waste dumps, which could affect the underground mining constructions or the related surface areas, were consider. It is most important to establish the priorities in order to obtain a high efficiency by combining the measures according to the environmental analysis and risk assessment.

Jan 1, 2005

By Robert Cooke

This paper shows how technology developed to analyse stabilised slurries can be applied to paste flows. The rheological characterisation of paste mixtures using the generalised yield pseudoplastic rheological model is described. It is noted that the slump test does not provide a complete rheological characterisation of a paste. Methods for calculating pipeline pressure gradients for laminar and turbulent flow are presented. The minimum pressure gradient is an important consideration to ensure that solids do not settle on the pipe invert. Important points to be considered for a pipe loop test programme are noted. The usefulness of the pseudo shear diagram for scaling pipe loop test measurements is demonstrated. Issues to be considered for the design of paste reticulation systems are discussed.

Jan 1, 2001

By Zhuang Jianming, Liu Qinxia, Yuan Mingliang, Mei Xiangong, Chen Jin

Up to now, the leaching of manganese carbonate ore is usually performed at high temperature of 363K and the leaching rate is lower than 90%. Although in laboratory test, the leaching rate is only 90%. This paper introduced an improved method for leaching of manganese carbonate ore. Certain ammonium salt was added to the pulp to raise the solubility of Mn2+ and reduce the adsorption quantity of Mn2+ on the ore surface. Experimental results show that a leaching rate over 95% can be obtained at the temperature >273K. The activation energy is calculated to be 7.15 KJ/mol and is lower than that of normal leaching technique. The effects of the parameters, such as particle size, pulp density and initial acid concentration on the process results are investigated. A leaching rate higher than 95% can be obtained under the following conditions: particle size below 0.25mm, leaching time 60 min, stirring speed higher than 960 r.pm. H2SO4:MnCO3>1 .2, pulp density 105-205 g.L-l. A kinetic model was deduced, verifying with actual experiments. It showed that the model can describe the leaching process successfully.

Jan 1, 1995

By E. B. McNew, J. M. Barnes, A. E. Torma

The applicability of biosorbent materials for the removal of uranium and other heavy metals from synthetic and actual uranium mil 1 tailing (UMT) solutions has been investigated. The biosorbent materials used in this study were barium loaded beads of alginate, alginate-dextran sulfate, alginate-carrageenan, and alginate-xanthan gum. These studies were performed in stirred vessels and packed columns. It was observed that 100 percent of the uranium could be removed from a synthetic solution following 2 hours of contact time in a stirred vessel, and 80-100% of U, V, Mo, Mn, Sr, and Zn could be removed from a UMT effluent solution with a packed column. Kinetic evaluations were performed, using a generalized rate equation, on the biosorption of uranium with these barium loaded beads.

Jan 1, 1992

By Luiz Roberto Amaral, Peter Frobenius

Construction of the first phase of the Sao Paulo Metro, the North-South Line, will be completed late in 1974. The downtown section of this line consists of 2.2 miles of 19.6-foot diameter soft ground tunnels and 3 subway stations. The entire tunnel - station package was let to one contractor. A plan and profile of the tunnels and stations is shown on Figure 1. Passage of the tunnels under Boa Vista Street in the Sao Paulo Financial District was one of the major challenges. The street is only 50 feet wide from building line to building line and flanked by 10 to 20 story buildings. The tunnels pass within 4 feet of adjacent footings. Further south, the tunnels run 13 feet below the flat foundations of the Caixa Economica, a massive 11 to 14 story building. Surface settlement had to he limited to less than .07 feet/tunnel and good face control and grouting procedures were essential. For this reason, full face cutting wheel tunneling machines were selected to drive the tunnels south of the Access Shaft Prestes Maia which included Boa Vista Street and the Caixa Economica. The tunnels north of the Access Shaft Prestes Maia were driven under a fairly wide Avenue and greater settlements were permitted. Open face shields were selected to drive these tunnels. Most of the work has now been completed and analyzed. Here are some of the results - Careful planning and execution of tunneling procedures kept surface settlement over the tunnels below a magnitude of .05 feet, allowing tunneling adjacent

Jan 1, 1974

By J. Finch, J. Yianatos, N. W. Johnson, R. Espinosa-Gomez

A method of determining the maximum concentrate solids rate or carrying capacity is described for given column operating conditions. The method requires alteration of the feed rate of solids to the column at a fixed residence time by manipulation of the % solid of the column feed pulp or the bias rate. The carrying capacity was measured for five streams at the Mt. Isa Mines Pb/Zn and Cu concentrators. As a potential scale up parameter, the mass of solids per unit time per unit column cross section (Ca, g/min.cm2) is explored. Ca is tentatively related linearly to the 80% passing size (d80) of the concentrate. For d80 < 15 pm Ca was less than 4 g/min.cm2 (8 lb/min.ft2) which makes it a critical consideration in scale-up for such fine feeds. An alternative carrying capacity parameter, mass of solids per unit volume of gas Cg was not as useful as Ca since Cg varied inversely with gas rate.

Jan 1, 1988

By D. K. Denton, D. F. Scott, T. J. Williams

Spokane Research Center personnel have been investigating the use of seismic tomography to monitor the behavior of a rock mass, de¬tect hazardous ground conditions and assess the mechanical integrity of a rock mass affected by mining. Seismic tomography can be a valuable tool for determining relative stress in deep, >1,220-m (>4,000¬ft), underground pillars. If high¬stress areas are detected, they can be destressed prior to development or they can be avoided High-stress ar¬eas can be monitored with succes¬sive seismic surveys to determine if stress decreases to a level where de¬velopment can be initiated safely. There are several benefits to using seismic tomography to identify high stress in deep underground pillars. The technique is reliable, cost¬effective, efficient and noninvasive. Also, investigators can monitor large rock masses, as well as moni¬tor pillars during the mining cycle. By identifying areas of high stress, engineers will be able to assure that miners are working in a safer envi¬ronment.

Jan 1, 2000

By John A. Herbst, William T. Pate, Ruben Tello Flores, Humberto Arreola Zarate

Plantwide control is the networking and coordination of individual control systems throughout the plant to enhance plant performance. The high level decision making involved in this coordination is used to achieve overall plant optimization. Decisions must be based on knowledge and information moving between control systems in both downstream and upstream directions and on management information systems containing financial data on the impact of coordinating actions. For example, certain quantitative descriptors of upstream operations are passed to the downstream control systems to prepare those operations for the feed material they will receive. Likewise, other quantitative descriptors of downstream operations are passed to upstream control systems to modify their output. In this case, setpoints are determined throughout the plant which maximize profitability, given current ore conditions and plant operating constraints. Due to the wide area coverage of this coordinator, it is forced to draw on several diverse information and knowledge bases. Such a coordinator, then, must rely on a combination of heuristic logic, model-based control and neural networks to unify the knowledge bases as well as to take advantage of their strengths and to compensate for deficiencies. A description is given of control systems for primary and secondary grinding and flotation at a large copper concentrator and how they are being integrated to achieve plantwide control. Financial implications are discussed.

Jan 1, 1995

By W. A. Rickelton

The first commercial use of phosphine derivatives as solvent extraction reagents began in the mid 1970&apos;s with the construction of several plants to recover uranium from wet process phosphoric acid. The process eventually adopted by all of these plants used the well known trioctylphosphine oxide (TOPO) in synergic combination with D2EHPA to extract U(6+). This prompted the development of other phosphine - based reagents and led to the discovery of a variety of interesting commercial and potential applications which are summarized in this paper. The applications include cobalt-nickel and niobium-tantalum separation and the selective recovery of silver and zinc.

Jan 1, 1994

By D. Carlson

At the Freeport Indonesia Grasberg Mine in Irian Jaya, Indonesia, a system of underground drainholes and surface drain wells have been designed and are currently under construction. The underground drainholes are located at elevations of approximately 9,600 feet and the surface drainwells located at elevations ranging between 12,500 and 13,000 feet. Together they will be used to drain the ground water contained within relatively incompetent rock. This drain system will allow for the successful dry mining of the open pit, and provide slope stability of the pit wall. The surface drain well network, when completed will allow for the draining of ground water to the Amole Drift where the underground drainholes are constructed.

Jan 1, 1998

By Richard A. Williams

The design, modelling and simulation of solid-liquid mixers remains one of the least advanced aspects of minerals processing, due to difficulties in quantifying complex slurry hydrodynamics from first principles, and in acquiring reliable experimental data for model verification and development. This contribution describes the application of electrical resistance tomography (ERT) for three dimensional imaging of the concentration of mineral particulates in a slurry mixer as a function of key process variables (particle size, impeller type, agitation speed). It is demonstrated how ERT can provide a wealth of detailed data to allow model development, which ultimately will lead to much improved design capabilities and the generation of mixing models which could reside within Particle Process Simulators. This principle is illustrated using descriptions of mixer behaviour based on an empirical approach, although the measurement methodology described is equally suited to development of computational fluid dynamics models, cellular models or design approaches based on artificial intelligence. The experimental data can be built into a visualisation data bank, which acts as a "process toolkit" by allowing a library of process responses to be catalogued. Hence these data can be accessed for the purposes of model development, equipment selection, optimisation of operating conditions or testing on-line control strategies.

Jan 1, 1995

By W. L. Cornell, F. W. Benn

The U.S. Bureau of Mines investigated froth flotation techniques to remove heavy metals (Pb, Cu, and Zn) from southeast Missouri lead mill tailings. It has been estimated that southeast Missouri contains between 200 and 300 million st of Pb tailings stored above ground. The tailings were classified as two distinct types: (1) pre- 1968 tailings from the Old Lead Belt (some more than 100 years old) and (2) post-1968 tailings from the New Lead Belt. The objectives of the investigation were to reduce the Pb remaining in the tailings to (500 ppm (<0.05% Pb) and to attempt to recover a marketable concentrate to offset a portion of the remediation costs. The remaining dolomite-limestone would then be used as mining backfill or agricultural limestone. Bench- scale froth flotation removed, in percent, 95 Pb, 84 Cu, and 54 Zn, leaving 94% of the original weight containing, in parts per million, 400 Pb, 40 Cu, and 300 Zn from the Old Lead Belt tailings. Separate flotation tests also removed, in percent, 85 Pb, 84 Cu, and 80 Zn, leaving 75% of the original weight containing, in parts per million, 400 Pb, 200 Cu, and 500 Zn from the New Lead Belt tailings . Concentrates recovered from the Old Lead Belt were retreated to produce a final Pb concentrate containing 72% Pb with a cleaner flotation recovery of 79%. Froth flotation proved to be a viable method to remove the heavy metals.

Jan 1, 1992