Search Documents

By A. K. Bakshi, Komar S. Kawatra

A plant trial of a new on-line pressure vessel rheometer for slurries, developed at Michigan Technological University, was carried out at a nearby copper concentrator. The rheometer measured the flow curves (shear stress vs. shear rate) of chalcocite slurries. Viscosity of non-Newtonian slurries changes with shear rate and so, for such slurries viscosity measurement at a single shear rate (often seen in the literature for grinding and classification studies) cannot be correlated to process performance. For these slurries, viscosity at various shear rates can be measured from flow curves generated by the pressure vessel rheometer. Other rheological properties, such as flow type and yield stress can be determined by this rheometer to better characterize the slurries. The slurry at the copper concentrator consisted of ground chalcocite ore. The solids content in the slurry varied between 30-60 % by weight. Top size of the particles was 125 micron, and 80% passing size was 34 micron. Measurements by the pressure vessel rheometer showed that most of the slurries had pseudoplastic flow at shear rates below -3000 sec-l, where the viscosity of the slurry decreased with increase in shear rate. Above -3000 sec-l, like a Newtonian fluid, the viscosity of the slurry remained steady. Flow curves and viscosity from the pressure vessel rheometer were verified with a Brookfield viscometer and a vibrating sphere viscometer, and the results were found to be accurate.

Jan 1, 1997

By R. V. Ramani, R. Srikanth

A three-part study was conducted to relate the dust generation propensity of a coal sample, defined here as the dust generation rate (grams of dust generated per tonne of coal broken), to its characteristics, in order to rank coal seams according to their respirable dust generation potential. In this paper, the results of a single breakage study on a variety of coal samples encompassing all coal ranks, and samples from operating mines are discussed. Further, where data are available, the primary dust generation rates of coal samples collected from underground coal mines are compared with the in-mine dust generation rates. The results of this analysis are then used to apply the results of this study to longwall face ventilation design. Vitrinite reflectance, and level of organic metamorphism are highly correlated with primary respirable dust generation rates of bituminous coal samples. The dust generation rates in underground coal mines are an order of magnitude higher than the primary dust generation rates in the laboratory. Depending on the type of coal, production rates, and dust control procedures, the air quantity required for airborne dust control can vary significantly. The air quantities on some high production longwalls are approaching the limits beyond which it may not be possible to reduce ambient ARD concentrations to less than 2 mg/m3 by dilution ventilation alone. In these cases, the miner's exposure should be controlled through the use of personal protective de- vices and administrative practices.

Jan 1, 1997

By Yoginder P. Chugh

It is well known that weak floor conditions in central Illinois affect pillar and mine opening stability. The floor interaction with coal pillars and immediate mine roof are being studied using two dimensional (plane-strain) elastic-plastic finite element models. The effects of varying soft floor thickness, coal seam- thickness, width of mine openings and strength parameters of coal and mine floor are being evaluated. The finite element models developed by Agbabian Associates and Dahl were utilized in this study.

Jan 1, 1982

By D. Kang, K. N. Han

The adsorption behavior of silver in ammoniacal solutions on activated carbon was studied. In addition to the concentration of ammonia, the parameters that affect adsorption include temperature, degree of agitation and anion and cation concentrations. In the study, it was found that the adsorption of silver from ammoniacal solutions is dependent on the initial silver concentration in the solution. It was also found that the recovery of silver from ammoniacal solutions is not as effective us gold. The adsorption rate was relatively slow overall, despite a rapid initial adsorption. The apparent activation energy ,for the adsorption was measured at 30.2 kJ/mol. It was believed that the kinetics of the silver adsorption on activated carbon was limited by a mixed control mechanism.

Jan 1, 1999

By Y. Kurokawa, R. Kurosawa, I. Iwata, I. Fukuoka, N. Sugita

INTRODUCTION The Ningyo-toge Mine is located in the western part of Honshu, about 800 km from Tokyo. Since the discovery of uranium ore deposit at Ningyo-toge in 1955, different kinds of mining and milling tests have been carried out. A new pilot plant of milling and UF6 conversion is also being under construction. Operations are scheduled to start by the end of this year. In 1979, the uranium enrichment pilot plant was constructed at Ningyo-toge and test operations have started. Thus, the Ningyo-toge area is assigned to undertake the Research and Development of the upstream of the nuclear fuel cycle in Japan. PNC has been strengthening its security measures more than ever. This paper will focus on the disposal of wasted material, especially on the disposal of heap leaching residue, in Japan. URANIUM ORE DEPOSITS The uranium of the Ningyo-toge Mine is characterized genetically by epigenetic sedimentary type deposits. They occur in the host rock of Neogene tertiary fluviatile conglomerates and sandstones which unconformably overlies the Mesozoic-Palaeogene granitic basement covered with lucustrine deposits and volcanic ejecta. More than 12 deposits have been found over the area of approximately 160 km2, and distribution of the deposits are strongly controlled by the so-called channel structure, probably remnants of paleo-streams on the denudation surface of the underlying grantic basement. Each ore body has different shape and dimension respectively, but about 2-3 meters thickness with the average grade of 0.05-0.2% U308 is common feature of the ore bodies. The ore is soft and loose, and it is composed of common rock forming minerals of allogenic origin and their altered products. The chemical composition of the ore depends on the constituents of the country rocks or the pebbles. A primary mineral, ningyoite and secondary mineral, autunite are major ore minerals, although three primary tetravalent minerals and thirteen secondary hexavalent minerals have also been detected. MINING EXPERIMENT Since 1959, various types of underground mining tests have been carried out at Ningyo-toge Mine. The room and pillar method was safe and simple, although the uranium ore recovery was below 70%. After experiment of the retreating long-wall method and slicing mining method, it was found that the modified long wall method was the most appropriate for the underground mining of the Ningyo-toge uranium deposits. This method was completed successfully to increase efficiency up to 2 or 3 times, as compared to conventional methods. MILLING EXPERIMENT In 1964, a small test mill was constructed at Ningyo-toge, and a milling experiment using the Ningyo-toge uranium ore was started. Re-modelling of equipments and improvement of the process lead to the establishment of the technique of the so-called wet process, and produce UF4 directly from the ore. The flow diagram is shown in Fig. 1.

Jan 1, 1981

By Ian S. Ross

The emphasis in this paper is focussed on dry bulk car go or the same cargo converted to slurry form for ease of handling. It is this type of cargo which is of primary interest to the mining industry whose products it represents to a large extent. The design problems associated with the handling of liquid bulk and of unitized cargo are sufficiently different to be treated separately. This paper then will consider the port handling facilities of dry bulk commodities as part of a system consisting of (1) the movement of products to the port area, (2) the movement of products out of the port area and (3) the handling of products within the port area itself. Expanding within these three components of the total transportation system, the paper will discuss the various difficulties encountered concerning the mode of transport into the port area and the method of handling product from transport to stockpile. Secondly, and before discussing the port area itself and in order to complete the conditions under which the port must operate, the movement of products out of the port area will be covered dealing with such items as the accommodation of the ship, problem associated with the very large ships, optimum berthing arrangements and the need to consider the various costs associated with the vessel. Finally the paper will review within the port or interface area such items as stockpiles, method of recovery, inventory control and an outline of the common design difficulties encountered. In all cases the relative influence on the total transportation costs of each of these dry bulk transportation system components will be considered.

Jan 1, 1972

By P. Mousset-Jones, F. Calizaya

Ultrasonic anemometry is a relatively new method of measuring the air velocity in underground excavations and is not widely used. The method has been mainly used for surface applications, such as meteorology and fluid flow measurement. Several instruments were looked at to determine their applicability for continuous underground monitoring systems. The units fall into two main categories: variable distance units and fined distance units. The method relies on the acceleration and deceleration of ultrasonic pulses transmitted through a moving airstream. This study presents some of the results of the testing of variable and fixed distance ultrasonic anemometers in a wind tunnel and a mine drift.

Jan 1, 1995

By Angus Maxwell, Jacob Grasmick

As the tunneling industry continues to adopt Tunnel 4.0, digital twins of the tunnel construction site are becoming standard requirements for tunneling projects. However, the benefits of these remain unproven to many practitioners. The paper discusses the various implementations of digitalization and describes efforts to combine all data types to analyze the relationships between influences, predictions and performance in a single digital platform. This includes data pertaining to investigations, design, construction, monitoring and post-construction asset performance and management. Based on 16 years of global tunneling projects the paper aims to quantify the tangible and intangible benefits of such systems. Using a number of real examples, the paper describes where opportunities were taken and where they went unrealized. Challenges and considerations for both procuring and developing these digital twins are also discussed.

Jun 13, 2021

By B. van der Moolen, P. J. M. Groot

The introduction of liberalisation in Dutch mineral provision has created a lot of uncertainty on how and where to supply for the need of construction raw materials. Some possible effects of this policy shift are: 1. the extraction of materials from small pits with truck transport, 2. an increasing dependence on foreign suppliers, 3. the usage of marine dredged materials, 4. more input of secondary substitutes. The outcome of this policy and the resulting marketbehaviour have consequences for transport and infrastructure and hence for sustainability issues. Mineral provision, on the other hand, is also influenced by the availability of infrastructure. Insufficient transport capacity could hamper the development of mineral projects that render benefits to society. (Even) in a liberalising market for mineral provision, the central and local governments have an important role to play with regard to infrastructure and the effects of transport. Various trends point towards an increasing internationalisation in mineral provision. What will increasing trade and increasing influence of the market mean for transport infrastructure? How should increasing transport be judged with respect to sustainability? In the sustainability discussion these questions will have to be answered on a national as well as on a European scale.

Jan 1, 2005

By III Kimball

For many years, Arizona merely shadowed EPA's environ-mental regulation of mining operations and waste. During this period, Arizona generally assisted EPA in the implementation of federal programs and enacted environmental laws patterned closely after their federal counterparts. A growing public concern about protecting water quality, particularly groundwater quality, eventually caused the State to depart from this pattern.

Jan 1, 1989

By M. G. Karfakis, K. P. Chong

Determination of fracture toughness using the semi-circular specimen, the chevron edge notch round specimen, the short rod specimen and the cylindrical burst specimen, are critically reviewed. These methods, among all, are the most applicable for fracture toughness determination of rocks. They require minimum machining. Samples are small, and testing procedures are simple. They have a sound analytical basis and allow the fracture toughness to be determined without measurement of fracture length.

Jan 1, 1986

By R. L. Peyton

Risk analysis is used extensively in many engineering applications. Although its use in the field of dam safety has been limited in practice, it has received considerable attention in recent years in the dam safety literature. Thus far, it has been shown that risk analysis in the evaluation of existing dams has the potential for providing a more rational basis for decision- making because of its focus on the direct issues--likelihood of failure, likelihood of loss of life, and risk cost of damages. It provides for a logical balance between the risk a dam imposes and the degree to which rehabilitation is required, compared to traditional evaluations based on somewhat arbitrarily chosen design events applied to large classes of dams. Dam owners could benefit by optimizing the cost of remedial measures. Downstream landowners could benefit by minimizing the likelihood of flood damages. However, it is also clear that significant technical and policy issues remain to be resolved before risk analysis in dam safety is accepted and routinely implemented in engineering practice. An obvious and important potential application of risk analysis is its use by the state regulatory agency as an in-house evaluation tool, or even as part of regulatory policy, in the implementation of its state dam safety program. Adoption of such a policy would have an important impact on the mining industry. .Although no state dam safety programs are known by the writers to have officially incorporated risk analysis into their regulations, there appears to be considerable interest in the concept. In recent surveys 47 states agreed that the development and promotion of a risk assessment methodology for state dam safety programs should be encouraged (Tschantz, 1983; Tschantz, 1984). The issue has also received important attention within the Association of State Dam Safety Officials (1986). One state-Illinois-proposed regulations during 1986 to allow risk analysis to justify lower spillway requirements for existing dams (Illinois Department of Transportation, 1986). At the Federal level, the National Research Council has found risk analysis especially appropriate for assessing dam safety at high-hazard dams (National Research Council, 19851, the Bureau of Reclamation has published guidelines for incorporating risk analysis into their dam safety grogram (U.S. Department of the Interior, 1986), and the Federal Emergency Management Agency has recently sponsored workshops and supported research related to risk analysis in dam safety (Federal Emergency Management Agency, 1985a ; Federal Emergency Management Agency, 1985b; - - McCann, et. al., 1985a, 1985b).

Jan 1, 1986

By S. P. Banerjee

There has been a phenomenal increase in production of coal from opencast mines in India. At the same time environmental problems caused by mining are receiving greater atttention. Deterioration in ambient air quality due to increased concentration of suspended particulate matter (SPM) in and around an opencast project is a major problem. Some measured values of SPM level around opencast mines in diff coalfields show that in many cases the TLV of 500 ug/m^3 is exceeded. The impact of dust emission from a mining project on surrounding areas are estimated by using computer models for air pollution dispersal but such treatment suffers from errors in predicting the dust load and failure to take into account the terraced nature of the opencast mine site. The haul roads have been identified as the most prolific source of dust and some recent trials on haul road dust consolidation in Indian mines are mentioned in the paper. Statistics regarding pneumoconiosis cases in Indian coal mines for the last decade are presented to show an increase in reported cases and a gist of the recently amended regulations on the subject of precaution against dust is mentioned.

Jan 1, 1991

By Otis M. Clarke

Although most bauxite mined is used to make metallic alu¬minum, more than a million tons of bauxite is used annually in the United States in the manufacture of refractories, chemicals, abrasives, and cement. Raw material requirements are becoming increasingly difficult to meet because high-grade bauxite, required for some uses, is limited. The supply of raw material for high-alumina refractories is most critical because a low-iron bauxite is needed. Although there are substantial bauxite reserves in the world, bauxite suitable for use in refractories is limited to a few districts.

Jan 1, 1977

By Byron V. Knelson

Although the concept of centrifugal recovery has been around in one form or another for many years, it has not been until recent times that it has become clearly understood and properly put into perspective. Simplistic in theory, it is when one begins to examine the variables involved that the true complexities of this matter begin to emerge. In creating an enhanced g force concentrator, there are many aspects both positive and negative that are encountered. Many conditions that are inherent to all conventional 1 g concentrators do not apply to centrifugal concentrators and therefore very few cm factors exist between them. In developing this technology, virtually all principles were proven by method of trial and error. Among the topics discussed are the effect of g force enhancement on particulate behavior with respect to size and shape, density, enrichment, fluidization, and the "teeter principle". In addition, we will discuss the physical effects of g force enhancement with respect to manufacturing in the areas of abrasion, bearings, and vibration. In discussing the recovery parameters of centrifugal concentrators we will draw direct comparisons to various other recovery methods, outlining the conditions most favorable to their application.

Jan 1, 1988

By Ian J. Duckworth, Pierre F. X. Mousset-Jones

A detailed heat flow project was conducted at the Homestake Mine in Lead, South Dakota. This paper presents results obtained from a stope sensor system installed in the mine. The design and installation of the system are described in detail in a previous paper (Duckworth et al., 1992). The major project objective was the construction of a comprehensive heat flow data base to allow the design and testing of a new climate prediction model applicable to irregularly shaped underground excavations in non-homogeneous surrounding rock types. A mechanized cut-and-fill (MCF) stope contributes a substantial overall heat source in a mine, and the effect of this source on the working environment must be considered when planning future ventilation and refrigeration requirements. The relative magnitudes of the component heat sources encountered with the MCF mining technique are presented, having been computed from actual stope beat flow data collected over a one-month study period. The percentage of the overall heat load that is removed from the scope for each component heat sink is evaluated, and the overall energy balance is analyzed. A one-month study length was considered a sufficient period of time to allow stope monitoring for a complete range of mining conditions.

Jan 1, 1993

By Martha E. Smith

INTRODUCTION Radiation is one of the many agents occurring in our environment that is capable of causing cancers. We are all unavoidably exposed to natural background radiation. If we wish to exploit the beneficial uses of radiation in medicine, industry, and for the production of electricity, some further exposures to radiation are almost inevitable. One needs to ensure therefore, that the standards of radiation protection are safely derived and one would want to understand the mechanism by which radiation might cause cancer and genetic defects. In order to study the effects of radiation one can: (1) analyze human data, (2) perform animal experiments, and (3) do molecular level experiments. Indeed all three kinds of information are needed. This paper will concentrate on the steps required to obtain some of the necessary human data regarding health effects, where the concern is about the impact and consequences of long-term low-level exposures to an agent. Such investigations require some knowledge of work histories, dose histories, health "outcomes", and the personal identification of the individual involved. Three inter-related computer systems have been developed at Statistics Canada which have been designed to permit optimal use of a number of different records for our entire country for such health related research. The development of the Canadian Mortality Data Base, the initiation of the National Cancer Incidence Reporting System, and the development of new computer linkage techniques have helped reduce the cost and increase the scale and efficiency of automated follow-up to produce statistics of sickness or death associated with radiation and other carcinogenic agents in mines. These computer systems have already been implemented, and references will be made to studies currently being conducted using these files and facilities (e.g. a study of all Ontario miners, plus various Canadian uranium, fluorospar, salt and nickel miners). We will also look at the kinds of data that need to be collected now, to improve such studies in the future. DELAYED RISKS - THE STUDY SIZE AND COST Delayed effects on human health, as for example industrially caused cancer, can in general only be detected and measured by following-up the individuals to see what eventually becomes of them. What is not generally recognized is that the relatively low levels of individual risk, about which the public is often concerned, usually requires for their detection that very large numbers of "exposed" and "control" individuals (e.g. 10,000 to 100,000 or more) be followed over a period of two or three decades to determine when they die, what they die of, and whether they contracted cancer or some other disease of special concern. Thus, it is frequently exceedingly difficult to make such investigations cost-effective so that they will be undertaken at all, and as a result very real risks to health can remain undetected or unquantified. THE MANUAL PROCEDURES Follow-up of individuals by epidemiologists has until recently been a largely manual and clerical operation. It has used a diversity of source record files; local, regional, and national. Often the tracing of people has involved letters sent through the mails and visits to institutions, physicians, municipal offices, and former neighbours. Only thus could one find out whether the individuals were dead or alive. Such studies were necessarily small, or else very expensive. Death registrations have, by tradition, provided a valuable tool for the identification of harmful influences in the environment. However, with the increasing mobility in the population, death may often occur far away from the place of exposure to such an influence. Thus, no longer will simple manual searches in a single registry office suffice to inform the investigator concerning the deaths that may have occurred in a study population, especially when that population is large. In the past, manual follow-up to locate the relevant death registration normally required some prior knowledge of the province and year of death in question, so that the alphabetic indexes could he used to direct researchers to the appropriate bound volumes of registration forms. To search manually in this fashion for any large number of death registrations, without knowing in which year or province the deaths had taken place, or even whether they had yet occurred, would be impractical, since each year in Canada there are about 170,000 deaths. DEATH AND CANCER AS SPECIAL ENDPOINTS Much of recent effort has been focused on the organization of the "endpoint" files required to do long-term follow-up studies on a national scale, because that is a function which other institutions are unable to perform due to the confidentiality laws governing the use of such information. Outside organizations generally come to us with detailed "starting" point records which relate to some specific group requiring study. We carry out these epidemiological searches on a cost-recovery basis. The analytical interpretation of results is normally

Jan 1, 1981

By Z. T. Bieniawski

Ground support requirements for safe and economical design of room and pillar coal mining layouts are reviewed. The design methods for mine roofs and mine pillars are discussed and the role of the geotechnical aspects is considered. It is shown that current support design procedures in the United States do not utilize fully the latest research findings and the need for more effective technology transfer in coal mine ground control is emphasized. Promising new developments in ground support are identified and possible research areas are suggested.

Jan 1, 1982

By T. M. Ruff, W. G. McCoy, M. J. Beus, S. Iverson

Monitoring conveyance position and wire rope load directly from the skip or cage top offers several significant safety and production advantages. The Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) developed a shaft conveyance monitoring system (SCMS). This system consists of position and guide-displacement sensors, a maintenance-free battery power supply and a new sensor, which is mounted on the wire rope with a Crosby Clip, to measure hoist-rope tension. A radio data link transmits sensor output to the hoistroom. A state-of-the-art automated hoisting test facility was also constructed to test the concept in a controlled laboratory setting. Field tests in full-size shafts are now underway.

Jan 1, 2000

By Birger Schmidt

The design of underground nuclear waste disposal facilities poses new problems related to the requirement of long term safety against radionuclide migration. The degree and effects of rock disturbance caused by construction and by the long term thermal effects from the hot waste must be predicted with confidence. Computer modeling can, to an extent, be verified by accelerated near-surface tests. Credible extrapolation to deep, long-term conditions requires successful near-surface modeling verification, proper characterization of near-surface and deep rocks, and successful determination of in-situ stresses. Excavation induced disturbance may be assessed primarily by empirical evidence.

Jan 1, 1981