Search Documents

By V. R. Voller

The WTBAL computer program for evaluating material balances for minerals processing flowsheets was developed at the MRC and has been in general use for a number of years. This paper reports on two enhancements to the basic MTBAL routine. The original program accounted for errors in the process measurements and used estimates of measurement variability to calculate stream weights. Unfortunately, the estimate of measurement variability was fixed over all streams. In the enhanced version of MATBAL, named IMTBL, the program equations and their solution procedure have been modified to allow the estimated variability in a process measurement to vary from stream to stream. The .second enhancement involves making MTBAL interactive. As such, the user now prescribes his information in an easy-to-use fashion in a conversational mode via a terminal. Finally, an assessment of the feasibility of implementing IMTBL on microcomputer systems will also be reported.

Jan 1, 1982

By Stavros A. Argyropoulos

The strides that have been made in recent years in applying Artificial Intelligence to pyrometallurgy, are reviewed. The computer reproduction of the way in which a human being reasons and calls on past experience and stored knowledge when faced with problem will be extremely helpful in pyrometallurgy. It is expected that Artificial Intelligence will be applied in all areas of human endeavor. Areas of pyrometallurgy that are most promising for expansion into A1 in the near future are presented.

Jan 1, 1990

By J. K. Wolski

This paper addresses the effects of using jet fans as booster fans in mine ventilation networks. A method was developed to determine the pressure generated by jet fans using the momentum theory. The influence of a reduction cone and other ventilation parameters on the jet fan pressure was analyzed. Verification experiments conducted in the Waldo Mine are described. Examples are given to demonstrate the conditions for the effective use of jet fans.

Jan 1, 1998

By B. H. Richard, P. J. Wolfe, T. G. Holdeman

Guided seismic wave propagation was studied in the Lower Freeport (6A) coal seam in the Oak Park No. 7 mine near Cadiz, OH. Three component geophones were implanted in the coal at distances ranging from 72 m to 183 m from the seismic source. Both Love- and Rayleigh-type modes were observed but the Love-type mode produced the best data. Detailed analysis was performed on the best Love data and a Dziewonski map of group velocity vs. frequency was constructed. This map was in excellent agreement with a theoretical dispersion curve calculated for a model of the coal seam. The Love wave group velocity was found to have a minimum value of 510 m/sec at 275 Hz. Only the fundamental mode contributed significantly to the observed signal and it was observed up to the maximum distance available.

Jan 1, 1987

By Błażej Doroszuk, Robert Król

Mill drums are essential equipment in various industries for the comminution of materials. To optimize their design and operation for efficient and cost-effective processing, it is necessary to understand the behavior of the mill drum under various operating conditions. This study investigates the behavior of a mill drum using a combination of experimental and numerical methods. The factors that can influence the behavior of the mill drum, such as the size and shape of the mill, grinding media, rotational speed, filling level, and material properties, are discussed. Experimental methods can be limited in obtaining measurements of internal processes, so numerical methods such as the Discrete Element Method (DEM) are also used to simulate the behavior of the mill drum. In this study, the experimental measurements of the motion of the grinding media are obtained using computer vision methods, and the numerical simulations are calibrated using the experimental results. A designed experiment approach is used to evaluate the performance of the mill drum under various operating conditions. The results of this study can be useful for the design and optimization of mill drums to achieve better performance and energy efficiency.

Jun 25, 2023

By X. Wu, M. Karfakis, E. Topuz

The generalized ventilation network problems encompassing both natural and controlled splitting networks, is formulated using a nonlinear nonconvex programming model, which has not yet been solved satisfactorily. This paper presents a methodology which can deal with the problem. The proposed methodology converts the nonlinear problem into a linear problem, by using special ordered sets of variables, and optimizes it by a modified branch and bound technique. The global optimality of the methodology and its applicability to different cases are investigated

Jan 1, 1991

By Scott E. Broughton, Robert T. Tape

Heap leaching requires containment and storage of cyanide solutions, the volume of which may increase dramatically following an extreme storm event or extended wet periods. This paper describes a computer operated solution storage model developed to assist in the management of these requirements. It results from the accumulative efforts of various Klohn Leonoff engineers working on a number of heap leach projects throughout the western United States for the past several years.

Jan 1, 1988

By Jan W. Oberholzer, Patrick Linzer

The globally increasing environmental awareness which has manifested itself in the past few years also encompasses problems associated with mine closures. A crucial requirement for the effective planning, management, monitoring and control of mine closures is an information system which allows the qualitative and quantitative evaluation of proposed closure strategies, not only in terms of their local influences, but also of their potential effects on areas farther a field. This paper describes some of the closure associated problems and the establishment of such an information system from existing facilities, all of which are readily available. No modifications to these facilities are necessary, which enables rapid and cost-effective implementation of the system.

Jan 1, 1996

By Y. M. Jiang

Longwall faces can move at high advancing rates, but many geological variations can cause unexpected instabilities and production losses. The rapid movement makes it necessary to evaluate different geologic conditions in the rock mass as fast as possible to assess their effects on the longwall face and shields. It is believed that prompt awareness of geologic conditions is the key to preventing instability at a longwall face. This paper introduces the application of fuzzy set theory for characterizing and evaluating roof conditions. Real-time monitored data coupled with fuzzy set analysis provides valuable information, such as shield leg pressure, developing load on shields, intervals of periodic weighting and the ratio of developing loads during periodic to normal times.

Jan 1, 1997

By James W. Evans

It appears that all extractive processes involve, at one or more points, fluids (gases or liquids) and that the flow of the fluid is an essential part of the functioning of the process. Usually that flow is turbulent and the turbulent flow frequently determines the rates of mass and heat transfer as well as other important phenomena such as bubble/droplet breakup and coalescence, particle suspension, etc. Over the past decade many attempts have been made to model turbulent flows in metallurgical unit operations. The present paper summarizes some of that work. Amongst the operations considered are agitated leaching, ladle metallurgy, electrowinning/refin- ing, induction furnaces, Hall cells and electro- magnetic casting. Where possible, comparisons are made between model predictions and experimental results.

Jan 1, 1990

By J. Felipe Costa, Andrew H. White, Marcot T. M. B. Vilhena

Ordinary kriiing (OK) is an interpolation algorithm mostly used in earth sciences applications where it provides satisfactory results. Robust kriging (RK) is an alternative algorithm which at- tempts to minimise the problems caused by the existence of outlier values within a given data set. Robust kriging essentially consists of an editing step prior to running the traditional OK method. This study compares the interpolation results obtained by OK and RK. Two data sets were used. The first data set consists of 140 samples mimicking a drilling survey named cluster.dat. An additional feature of this sample data is that its parent population, the reference data set, is available, thus permitting direct quantitative assessment of the effectiveness of a given estimation technique. The second data set consists of a grid sampled at 1x1 m. The estimates obtained by OK and RK using cluster.dat were compared to the reference data set. RK provided better results in terms of quality of the estimates than OK

Jan 1, 1996

By S. Su, S. Natansohn

This report describes a process for tungsten recovery from Searles Lake brines and upgrading its concentration to useful levels. The method consists of a combination of a liquid-solid and liquid-liquid extraction step and results in a product stream containing more than l00g W03/1. This technique is also effective in substantially reducing the concentration of objectionable impurities in the tungsten product. An ion exchange extraction mechanism is postulated.

Jan 1, 1983

By W. K. Tolley, D. G. Kotlyar

Oxidized sulfide minerals, commonly formed by weathering, are becoming increasingly important resources as primary sulfide deposits are depleted. Oxidation, in general, reduces selectivity and recovery in flotation. The objective of this research was to determine the mechanisms of oxidation and collector adsorption in sulfide systems as a step towards developing improved technologies for beneficiation of oxidized sulfides. Data from microcell flotation tests are combined with electrochemical and spectrophotometric measurements. The adsorption of ethyl xanthate (EX) on oxidized sulfides was characterized using AC impedance and voltammetry techniques, and correlated to flotation response. Oxidation resulted in an electrically resistive, nonporous surface layer. The floatability of chalcocite, chalcopyrite and pyrite was dependent on the extent of oxidation. Oxidation for one day or more at 65ºC suppressed chalcocite flotation. Oxidized chalcocite also inhibited flotation of chalcopyrite and pyrite. Oxidation caused decreased chalcopyrite flotation. Pyrite flotation, however, increased after oxidation.

Jan 1, 1995

By R. Addison, P. V. Avotins, D. W. Kestner, M. F. Dibble, L. A. Haas, M. D. Flavel, D. Halbe, D. J. Barratt, G. V. Jergenaen

Mineral processing in 1980 can be described by several key words, familiar to the industry throughout the past decade: complex, low grade, environmental, energy, high tonnage, and economics. Flowsheets have become more complex in order to treat lower-grade, finer-grained, more complex ores and still meet environmental and economic constraints. Operators and researchers have had to cope with these problems, which have resulted in marked trends in mineral processing. The use of advanced instrumentation in process monitoring, control, and modeling has been increasing to deal with fluctuating ore grades, higher plant capacities, rapidly rising operating costs, and process complexities. The industry has been presented with new generations of equipment that reportedly do the job more efficiently and at a reduced cost. The need to meet stricter air and water environmental standards has resulted in a concerted effort by the mineral industries to obtain an appropriate balance between the needs of mining and mineral processing and the requirements for proper environmental, safety, and health protection. Energy and economic considerations have led to increased equipment size, particularly in grinding, flotation, and conveying. Throughout all phases of mineral processing there has been an effort to reduce energy consumption. One avenue followed by researchers and operators was the testing and use of chemicals to reduce energy requirements.

Jan 5, 1981

By Ken Bright

This paper is an overview of approaches to assessment of ore grade for gold and the platinum group at the exploration stage of a project. Proper sampling techhniques must be complemented by good assaying. In turn, correct assaying has its roots in thoughtful, systematic sampling and sample preparation procedures. While intricacies of the subject matter could occupy a book, we will comment on acceptable sampling approaches, outline a lab hand- ling scheme, and discuss preferred analytical methods. Pitfalls previously encountered by the mining and exploration industry will be highlighted with emphasis on a perceptive under- standing of the nature of ore occurrence. Lastly, focus will be centered on reliable assay approaches.

Jan 1, 1988

By John W. Kelse

What happens when the skull and crossbones goes on a product? In the case of cancer warnings, the consequences can be severe. If the label contains the term "lung carcinogen", you might expect to compensate a lot of smokers, meet a lot of expensive lawyers, be counseled by equally expensive consultants and pay sharply elevated insurance premiums, if you are able to obtain coverage at all. At the extreme, you may face plant shutdowns, job losses or even Chapter 11 bankruptcy. Regardless of how you fare, you are likely to learn some very disconcerting things about the risk evaluation and regulatory system which required you to label in the first place. If a particular material or product does pose a health risk, you are obliged both legally and morally to warn those potentially exposed. Once that warning appears on the label, however, the consequences are often beyond your control. You and your embattled product become part of a legal/regulatory system which has a life of its own. Therefore, the issue of health labeling is not so much whether one warns but rather whether the warning itself is justified and the reasonableness of what happens afterwards. It is this matter of justification and reasonableness, particularly of cancer warnings, which this paper addresses. Until, as they say, your ox has been gored, we tend to believe that risk is determined by the best available technology and expertise We expect that risk evaluators appreciate the ramifications of their work and place things in proper perspective; that risk has been appropriately demonstrated before it is publicized and regulated; that the time-honored concept of prudence, to err on the side of safety, has not been excessively stretched. Unfortunately, the risk evaluation process is rarely, if ever, this

Jan 1, 1991

By Jeffrey P. Carstens

INTRODUCTION Thermally induced fracture of rock is one of the oldest rock breakage techniques known to man. Primitive underground miners used fires to heat and crack rocks as early as the third century B.C. (Ref. 1). History aside, however, present-day tunneling and mining interests are reconsidering the use of modern heating units for rock fracture for some very good reasons. One of the most important advantages of many heating techniques is the lack of direct contact between the heating device and the rock. This means a lower wear rate relative to mechanical cutters, and no large reactant force to be supplied by the tunneling machine. In addition to avoiding physical contact, some heating systems (e.g., electron-beam guns and lasers) can deliver energy to a rock face much more intensely than can be conveniently handled mechanically. Thus, heating power densities of the order of lob to 107 watts/in.2 and greater can be achieved with high-power lasers. These high power levels allow much higher instantaneous penetration rates than can be achieved by mechanical cutting. Another advantage that accrues to some thermal techniques, such as, for example, surface spalling, is that the thermal fracture process works particularly well in certain rock types (e.g., granite) that are particularly hard to cut mechanically. Other methods, involving high power density, are able to cut any rock type, and are relatively

Jan 1, 1997

A new separator, known as the HydroFloat cell, was developed to overcome the limitations of traditional flotation cells in recovering coarse particles. The HydroFloat cell separates particles based on differences in mass after the selective attachment of air bubbles to the hydrophobic component of the feed stream. Proof-of-concept testing, utilizing phosphate matrix, heavy mineral sands and anthracite slag, indicated that significant improvements in separation efficiency can be achieved using this air-assisted teeter-bed system. Based on the encouraging laboratory results, a pilot-scale HydroFloat cell was fabricated and installed at a central Florida phosphate plant. Test data collected using the pilot-scale unit suggest that the BPL recovery of the +35-mesh plant feed can be increased by snore than 40% through the application of this new technology. This improvement is particularly beneficial due to the very high grade (-73% BPL) of the +16-mesh particles in the HydroFloat concentrate. This article describes the theoretical basis for the development of the HydroFloat cell and provides an overview of recent laboratory and pilot-scale test results.

Jan 1, 2002

By L. M. English, Y. J. Wang

When plotted as head vs. volume, fan curves start high and decrease with increasing volume, while mine head curves start low and rise with increasing volume. Their intersection is the system operating point. However, as every ventilation instructor knows, the fact that head loss is a negative number (debit) and fan head is an energy addition (credit) is often a stumbling block to student or audience comprehension since the curves seem to reflect the opposite. It is possible to use the intuitively correct curves- pressure losses as negative values and energy additions as positive values - and still obtain the correct operating point. Adding the two curves produces a third curve that intersects the x-axis at the operating point, the point at which the fan energy input exactly matches air circulation energy loss. Using this technique also makes it easier to account for outside influences on the system, such as natural ventilating pressure. With the standard approach, it is quite easy to add or subtract such influences to the wrong curve. This approach can be extended to the graphical solution of any series/parallel ventilation network. The results are the same, and the approach is logically consistent and less confusing.

Jan 1, 1999

At the dawn of the computer age in the early 1950's, few people in either the minerals industry or the field of electronic data processing (EDP) would have predicted the tremendous impact that the computer has had on the way we conduct our everyday lives and businesses. Herman Hollerith himself (see next page), the Columbia University mining engineer 'turned statistician who developed the first punched card electronic tabulating machines for the US Census Office in the late 1880's, would doubt- less be amazed at the progress that has been made in the application of data processing techniques to nearly all aspects of the mining cycle (Aul, 1974). More than any other factor, the availability of economical computing equipment has led the way for the development of the broad range of mining computer methods described in this text. While limits have been identified for many of the technologies commonly in use today, new technological advancements point to continued exponential advancements in computing price-performance in the 1980's. With those advancements, we may look forward to continued expansion of the role computers will play in mineral production.

Jan 1, 1979