Search Documents

By E. P. Fahrenthold, K. E. Gray

Introduction Brine reservoirs along the Texas and Louisiana Gulf coasts are currently under study to investigate the technical and economic viability of production wells designed to extract methane gas in solution. The effect of well pressure drawdown on reservoir rock and associated overburden material is important to well performance predictions and the analysis of potential subsidence problems. Consequently a series of compaction tests have been conducted on sandstone and shale cored from a test well drilled near Hitchcock, Texas, in order to determine the variation of mechanical properties to be expected over the producing life of the formation. Previous Work The referenced tests are part of an extended study of geopressured-geothermal reservoir behavior, including compaction (Jogi, Gray, Ashman, and Thompson, 1981 and Jogi, Kalra, Gray, and Thompson, 1981) and creep (Thompson, Jogi, Gray, and Richardson, 1981) tests of reservoir rock and related reservoir performance studies (Rago, Okhuma, Seperhnoori, and Thompson, 1985). Recent work has considered the nonlinear constitutive behavior of sandstone (Fahrenthold and Gray, 1985 and 19861, while additional experimental work is reported here. Geological structure and composition of the Hitchcock field from which the core samples were obtained is discussed by Light (1985). Experimental Procedure Compaction tests were conducted on cylindrical cores, nominally 2.75 inches in length and 2 inches in diameter, with independent control of the axial, confining, and pore pressures. Axial and radial deformation of the samples were measured in tests over a range of effective stress states expected to develop over the reservoir lifetime. The term effective stress as used here refers to the algebraic difference of the total stress and pore pressure, with compression taken as positive. Three types of compaction tests were conducted on the sandstone. In the uniaxial tests, axial total stress and radial strain were held constant as the pore pressure was reduced, similating one dimensional compaction which may occur during reservoir depletion. In the triaxial tests, radial total stress and pore pressure were held constant as the axial total stress was increased, duplicating conventional rock compaction test procedures. In the pore pressure drawdown tests, axial and radial total stresses were held constant while the pore pressure was reduced, in order to investigate differences in sample response to mechanical and pore pressure loading. Compaction tests were also conducted on shale material obtained from the reservoir overburden. The field coring process provided few consolidated shale sections sufficiently large to allow preparation of samples with the dimensions described above. With additional attrition during sample preparation of this brittle material, ultimate yield of the coring effort was limited. The few available samples were tested in uniaxial and triaxial tests similar to those described above. The use of displacement transducers to measure sample deformation avoided the difficulty of strain gauge installation on this material. Test Results The sandstone and shale both demonstrated nonlinear stress-strain behavior, with hysteresis and residual strain present upon unloading. Polynomial interpolation of the stress-strain curves was used in the calculation of incremental values for the loading and unloading moduli. Figures 1 and 2 show example axial effective stress-axial strain curves for triaxial tests conducted on sandstone and shale samples. The figures plot incremental stress and strain variables, defined as deviations from the state of prestress to which the sample was subjected. The state of prestress was varied between tests in order to investigate material behavior over the entire stress and strain space of interest. Tables 1 and 2 give the incremental moduli (Young's modulus and Poisson's ratio) as a

Jan 1, 1986

By L. MacHue

Sulfur containing collectors have been shown over the years to function as strong, selective and non-selective sulfide mineral collectors. Unfortunately, the majority of the widely known sulfur based collectors are of low molecular weight, volatile and subsequently, possess an objectionable odor. Higher molecular weight sulfur based collectors (C9 and higher) are significantly less odiferous due to lower volatility and lower vapor pressures. In this study, a specific proprietary higher carbon number collector, Orfom® MC 37, was blended and used successfully to recover 2-3% additional molybdenum in a laboratory flotation system, when compared to a standard collector blend. Copper recoveries were also positively affected. Further testing is required to give additional conditions favorable to increased copper and molybdenum recoveries, but indications at this time show the proprietary sulfur based collector blend to be a selective collector of molybdenum, while providing a significant increase in copper recoveries.

Jan 1, 2010

By Bahaa Alyosif, Turan Uysal, Muhammet Kürsat Aydemir, MURAT ERDEMOGLU

 The paper investigates the effect of intensive milling on the conversion of microcline to potassium chloride during chlorination roasting. The study aims to improve potassium recovery by reducing the chlorination roasting temperature through mechanical activation.

Aug 1, 2023

By A. Hekmatnejad

"The objective of this work is to validate a methodology for spatially predicting the fracture intensity, defined as the average fracture area per unit volume. First, using the observations from drill holes, the fracture intensity is directly inferred at the support of drill-hole composites based on a Terzaghi correction. Subsequently, the composite values are interpolated to larger blocks. The methodology is tested on sets of simulated fracture networks, in which each fracture consists of a disc with a random diameter, random position and random orientation. For each of these simulated networks, one can calculate the actual fracture intensity within any region of space, based on geometric considerations. A regular sampling mesh is then defined to emulate a set of vertical drill holes and the proposed methodology is applied to predict the fracture intensity, both globally and locally. The actual and predicted fracture intensities are finally compared, showing that predictions are unbiased, insofar as, on average, the prediction error is always close to zero. Also, the error dispersion increases when the support of the prediction decreases, which is consistent with the well-known support effect. In practice, the proposed methodology allows predicting fracture intensity based exclusively on drill-hole information, without the need for simulating fracture networks in space, hence its interest. INTRODUCTION The characterization of fractures in rock masses is an important part in the evaluation of mechanical and hydraulic properties of rocks. Fractures have a large impact in disciplines such as reservoir engineering, safety of underground storage of CO2 or of nuclear waste, assessment of high-enthalpy geothermal installations, safety of mining exploitations, efficiency of in-situ leaching operations or of extraction by block-caving. As a rock mass property, fractures must be characterized in the three-dimensional space, whereas observations are limited to 1D (drill holes) and 2D (outcrops, drift walls), moreover very often to rather short stations, so that the available data are subject to geometric bias, truncation and censoring. Fracture characteristics includes the number of fracture sets and, for each set, the number, orientation, spacing, location, shape and size of the fractures must be inferred from data sampling. Some important parameters that are considered nearly in all models are fracture intensity and fracture size."

Jan 1, 2016

By R. A. Jankowski

Laboratory tests were conducted to evaluate the silica collection efficiency of flooded-bed scrubbers using six different filter panel designs at two operating velocities. Test results indicated that reductions in filter density negatively impacted respirable dust collection. Silica collection efficiency for the least-dense filter was as much as 33 % lower than the collection efficiency of the most-dense filter. At the low operating velocity, the least-dense filter allowed more than 40% of the respirable silica dust in the scrubber intake air to pass through the unit and back into the mine environment. Operation of the scrubber at the higher test air velocity increased silica collection efficiency regardless of the filter panel tested The density of the filter panels also impacted the quantity of air moved through the scrubber, with higher-density filters reducing scrubber airflow. For each filter, the relationship between dust-collection efficiency and air-moving capacity must be considered to determine the overall effectiveness for each mine application.

Jan 1, 2000

By Adrian Fleming

Adrian Fleming is Executive Vice President of Exploration for Golden Star Resources Ltd., Denver. Adrian is an Australian who graduated in 1973 with an honors degree in geology from Newcastle University, New South Wales. His extensive international experience has spanned exploration, project development, and operations for both large and small companies in Australasia, Southeast Asia, North and South America, and Africa. Adrian has been with the Golden Star group of companies for four years and he is responsible for all exploration activity. ABSTRACT Golden Star acquired the rights to the Omai prospect in 1985 at a time when the country of Guyana was out of favor with the exploration fraternity. Subsequently in the late 1980s and early 1990s, Golden Star acquired exploration properties in Suriname and French Guiana well ahead of its competitors. Golden Star's strategy entailed identifying windows of opportunity and aggressively pursuing them. We also recognized that the Guiana Shield hosted a significant area of highly prospective greenstones which were comparable in metallogenic potential to similar terrains in eastern Canada, western Australia and west Africa. The geological skills Golden Star developed and the exploration techniques employed to explore deeply weathered rocks are described. The paper highlights the key elements of Golden Star's strategy and illustrates how some of the milestones reached by the company led Golden Star to establish an enviable portfolio of gold and diamond properties in the Guiana Shield.

Jan 1, 1998

By J. Frenzel

The computation of hydrometallurgical equilibria is very difficult because of the many complex species in solution, the precipitates, condensed species, or solids, and the activity coefficient corrections necessary to non-ideal thermodynamics. Our objective was to tryout recently developed genetic algorithms to minimize free energy and solve the equilibrium computation. We selected test problems that were seemingly unsolvable with more traditional algorithms, and we applied genetic algorithms to them. We were pleased to find that genetic algorithms succeeded where other algorithms did not. We concluded that they are an effective tool for hydrometallurgical equilibria.

Jan 1, 1992

By David J. Collins

The emergence of activated charcoal adsorption as the most popular recovery method for precious metals, has led to numerous innovations aimed at increasing the efficiency of the process. This article describes a change in traditional charcoal transfer methods which will aid in reducing charcoal attrition losses. Studies have shown that significant charcoal attrition takes place during transfer, be it when using airlifts or centrifugal pumps. Tests conducted at Pinson Mines indicated a 4 to 8% loss to the minus 20 mesh fraction of charcoal after three (3) hours of pumping charcoal. Tests conducted while the author was at Jerritt Canyon indicated that charcoal transfer was a major contributor to charcoal losses; a decrease in the amount of coarse charcoal (plus 12 mesh) and an increase in the amount of finer charcoal (minus 16 plus 20 mesh) was noted as charcoal was moved to the head of the adsorption circuit.

Jan 1, 1998

By C. R. Stephan, N. B. Greninger, W. A. Slivensky

The U.S. Bureau of Mines and the U.S. Mine Safety and Health Administration (MSHA) are participating jointly in a research program to evaluate strength characteristics and air-leakage resistance of various proposed seal designs for use in underground coal mines. Over 20 full-scale seals were constructed in the Bureau's experimental mine at the Lake Lynn Laboratory, air-leakage tested, then subjected to pressure pulses of 0.14 MPa or greater. A discussion on the experimental procedure, construction techniques, and the explosion and air-leakage test results is presented. Four types of construction material were used during this seal testing program: solid-concrete-blocks, low-density foam blocks, cementitious foam, and wood blocks. Only one of the solid-concrete block designs using a mortared thick wall survived the explosion and air-leakage tests. Most of the low-density foam block and cementitious foam seal designs were judged to meet the requirements to be considered a coal mine seal. One of the wood block convergence seal designs failed explosion testing. Based, in part, on these research findings, several alternative seal design constructions using low-density foam blocks, cementitious foam, or wood have been approved by MSHA for use in coal mines.

Jan 1, 1993

By R. C. Jr. Babcock, V. S. Znamensky

The Pyke asbestos deposits were discovered by Kennecott Explorations (Australia) Pty. Ltd. in 1969 during the course of base metal exploration on the South Island of New Zealand. Extensive occurrences of chrysotile asbestos were found associated with the Red Mountain ultramafics in the headwaters of the Pyke River, and to the north and south along the ultramafic belt for a distance of 70 km. Surface evaluation and drilling by Kennecott in 1970 and 1971 identified numerous small deposits of good grade fiber in the Little Red Hills between the Pyke and Barrier Rivers. Additional drilling and three adits have been completed by other companies since that time. The property is presently held by Lime and Marble, Ltd., of Nelson, New Zealand, and Kennecott Explorations (Australia) Pty. Ltd. This chapter presents the regional and local setting of the asbestos deposits, including the geology and nature of mineralization. In addition, the exploration methods used by Kennecott in the discovery and evaluation of these deposits are outlined. Subsequent work by other companies is mentioned, but not de- scribed in detail. This subsequent work did not alter Kennecott's conclusions or produce any serious changes in the interpretation of geology and mineralization. The author acknowledges the contribution of the many employees of Kennecott Explorations (Australia) Pty. Ltd. who have been involved in the project. In particular, thanks go to Ramon Farmer, N.G. Corner, and A.W. McConie, who were responsible for completion of field work and reporting on the project. The responsibility for the conclusions and interpretations of this chapter are solely that of the author and result from his involvement in the discovery of the deposits and management of the exploration program. REGIONAL SETTING Ultramafic rocks on the South Island of New Zealand are thought to be Permian in age and occur between crystaIline and metamorphic continental rocks of Precambrian through Cretaceous age in the west, are thought to have once been part of the Antarctic subcontinent, and the extensive geosynclinal graywacke deposits of the Mesozoic New Zealand geosyncline in the east. They consist of the Dun Mountain ultramafics, a 130 km long segment of ultramafic rocks located at the north end of the South Island, and the Red Mountain ul- tramafics that occur in a zone 200 km long in the south half of the South Island as shown in Fig. 1. These two belts, once contiguous, have been offset a distance of 560 km by the still active Al- pine fault, which is analogous in character and offset to the San Andreas fault of the United States. The ultramafic rocks occur within a sequence of Permotriassic volcanic and sedimentary rocks that probably formed at the eastern margin of the continental plate. The ultramafics appear to be tectonically emplaced between Permian lithologies in the Dun Mountain belt (Coleman, 1966), and at the base of or between Permian volcanics and sediments in the Red Mountain belt. The Permotriassic ultramafic volcanic sequence of the Red Mountain ultramafic belt appears to be a typical ophiolite sequence. Ultramafic rocks, mixed mafic intrusive rocks and volcanics, volcanic rocks, and volcanoclastic sediments occur in apparent superposition from east to west in the area of Red Mountain. Farther south, ultramafic rocks are associated with basaltic volcanic rocks and some sediments, and still farther south are emplaced entirely in sediments. These structural compIications of the normal ophiolite sequence have resulted from the coincidence of Permian subduction, early Mesozoic extension and sedimentation, and Cretaceous subduction along the same plate margin (Landis and Bishop, 1972). The general geology in the area of the Red

Jan 1, 1986

By Jaime Guzman

Mineral exploration decision problems involve the economic evaluation of upgraded geological information and the costs of obtaining it. This paper presents a valuation theory of risky projects applicable to the analysis of exploration investments. The valuation model is predicated on the Capital Asset Pricing Model (CAPM) from financial economics; its parameters can be objectively measured from publicly available information. Geostatistics is used to derive simplified random cash flow models which incorporate the impact of improved deposit knowledge in terms of reduced estimation variance. The application of the theory is illustrated by means of hypothetical exploration optimization examples.

Jan 1, 1986

By Peter K. Weissenborn, Robert J. Pugh

The contrasting behaviour of electrolytes in inhibiting coalescence of bubbles was explained by the positive and negative distribution of anions and cations at the gadwater interface. Further, the efficiency of electrolytes which do inhibit coalescence of gas bubbles can be linked to a counter ion hydration mechanism and the effect of electrolyte concentration on gas solubility. A correlation was found between the transition concentration of electrolyte needed to prevent the coalescence of bubbles and the reduction in gas solubility. Hence, the inhibition of bubble coalescence in electrolyte solutions appears to be linked with the utilization of water molecules in the hydration of cations and a consequent reduction of water available for gas solubility.

Jan 1, 1995

By C. I. Walker

"Understanding the influence of slurry particle size on wear is essential to maximising the life of centrifugal pumps operating in mineral processing plants and for hydrotransport duties. Particle size influences not only the wear rate but also the wear pattern in pumps. Complicating the situation is the different relative wear rate for different pump parts depending on particle size. A simple Slurry Wear Type (SWT) number based on particle size and size distribution is proposed as a means for categorising slurry pump wear patterns and optimising pump application and material selection. INTRODUCTION The wear of centrifugal slurry pumps in mineral processing and hydrotransport can be quite severe and is one of the major cost concerns of plant operators. Some typical worn slurry pump parts made from high chrome white iron are shown in Figure 1. Erosion wear rates of up to 2 mm/day are not uncommon [1].Centrifugal slurry pumps are required to handle solid-liquid mixtures with a very wide range of particles extending from sub-micron size clay through to 200mm and larger cobbles. Particle size distribution can also vary widely from uniform and narrow (such as graded sand) through to very broad (such as grinding circuit slurries). Slurry particles may also undergo size change due to attrition during the pumping process. The major wearing parts in a slurry pump are the impeller, side liners and casing liner. These are shown with reference to a Warman® MC centrifugal pump in Figure 2. While many particle properties (including size, shape, hardness, density and concentration) influence pump wear, this work will consider only the effect of particle size as it is the major determinant of wear characteristics. Particle size influences the wear pattern, material performance and relative component wear rate in centrifugal slurry pumps. SLURRY WEAR TYPE (SWT) BASED ON PARTICLE SIZE Soil and grain size classification systems abound. Many have different limits to the ranges for a particular classification, albeit not too"

Jan 1, 2018

By Ronald M. Fedrick

The microtunneling project for the State of Hawaii's Natural Energy Laboratory (NELH) facility in Kona, Hawaii, was awarded to Nova Group Inc., Napa, California. Nova has developed both microtunnel and deep pile cofferdam experience. Both of which would be required for this project. The project was designed by Makai Ocean Engineering of Honolulu as a continuation of the Ocean Thermal Energy Project (OTEC). The world's first OTEC plant has been successfully operational at NELH since 1982 netting approx 50 kw of usable electric power from a gross generation of 210 kw. A second plant designed to draw 39°F cold water from 3,000 ft below sea level and produce a gross output of 1 mw with a net 500 kw of usable power required 2 - 54 in. finished diameter pipelines. An ongoing problem with earlier offshore pipelines has been the damage to the near-shore pipes within the surf zone. The necessity for a deeper connection between the land based pipe and submerged sea pipeline was obvious. Earlier pipelines had been drilled and shot through the shoreline. This process was only practical at shallow depths. Makai Ocean Engineering and the NELH scientists looked at different methods to get the pipeline through the shoreline at a depth of 80 ft below sea level. Initially, the direction drilling method was proposed as the most potentially practical method. A contract was awarded and various attempts were made to complete a successful

Jan 1, 1995

By H. Cho, P. T. Luckie

A study was undertaken to investigate the liberation behavior of coal macerals through size reduction and density separation. It was seen that the liberation of coal macerals could be achieved by size reduction, allowing selective separation of coal organic components. However, the degree of liberation was dependent upon the comminution history. Even for the same fineness, the extent of liberation might not be the same depending on how the material was generated. The liberation of coal macerals was analyzed by examining the liberation index. It was seen that, although comminution produced fine particles enriched in inertinite (primarily fusinite and semifusinite), these particles were less liberated than coarser particles. However, the liberation of macerals increased when all the feed was ground to a finer size.

Jan 1, 1999

By Elisa Comis, Barbara Bitetti, Julien Pepiot, Stefano Lione, Francesc Rich

The new Lyon-Turin railway project involves the construction of a 57 km twin-tube tunnel between France and Italy. Pini France (project leader) and Systra-SWS are the designers of Construction Site 8 (CO8). This part of the project includes the construction of the tunnel portal on the Villard-Clément platform, two 2.8 km long tubes of the base tunnel in the direction of Saint Martin la Porte, the cross-passages between tubes and the niches. This paper presents the general approach followed to design the temporary support for the base tunnel, cross-passages, and technical rooms. The design of the temporary support accounts for the variability of the ground and water conditions, the excavation attended behavior, the construction planning and the identified geological hazards that could be encountered along the alignment. Particular attention is paid to the intersections between the tunnels both in terms of numerical modelling and construction methods and phases. Two types of intersections are present in the project: the intersections between the cross-passages and the base tunnel and the intersections between the base tunnel and the niches. 3D models have been developed for the tunnel intersections.

Jun 23, 2024

By John C. Schneider

During the past decade, operators and researchers have worked toward a better understanding of the mechanisms operating in flotation. As reported by W. J. Trahar in 1981, this work commenced with the operators determining a relationship between recovery and particle size. They defined three particle size ranges, that being fine, intermediate and coarse. It was noted that the fine and the coarse ranges had slower flotation rates than the intermediate range as demonstrated by their lower recoveries.

Jan 1, 1998

By J. G. Groppo, S. M. Khandrika, B. K. Parekh

It is shown that dewatering of fine coal particles (D50 = 21 µm) is enhanced near the point-of-zero-charge. The coal surface is modified by the addition of copper ions and by adjusting the pH to precipitate surface-active metal hydroxy species, which promote agglomeration and produce low-moisture cakes. Filtration kinetics data are used in calculating filter cake parameters from an integrated form of Darcy's law. The influence of copper ions and pH on filter cake parameters and the correlations among them are presented.

Jan 1, 1995

By Darryl Amick, Keith A. Prisbrey, Lee E. Plansky

The problem addressed was to develop automated image analysis of metal welds to replace unreliable and costly 100% visual inspection. The objective was to evaluate neural networks combined with features from gray level surfaces. Photomicrographs of the welded seam in Zircaloy-4 channels used in nuclear fuel rod assemblies were examined. The methodology used was to select a set of morphological feature coefficients from Bessel Fourier morphological feature coefficients extracted from digitized photomicrographs. The selected morphological feature coefficients were then used to train a neural network. The approach was verified initially by successfully training a neural network using the known, secondary chemistry of the alloy welds. The results were good. The Bessel Fourier coefficients captured sufficient information from the metallographic images to distinguish weld quality. This approach has the combined advantages of compressing the images through Bessel Fourier coefficients and give the ability to rapidly process large amounts of data using neural networks.

Jan 1, 1993

By Wenhua Li, Tsuyoshi Adachi

Resource nationalism is essentially mandatory government intervention in natural resources businesses by political or economic means in order to benefit the nation and the people. It is attacking the mining industry more and more rampantly by all kinds of means since the twenty-first century. Poor countries who count on a resource-led economic growth usually find themselves trapped into “resource curse”. The harmfulness of resource nationalism for investors is that one event can quickly escalate and lead to a chain of events which make projects commercially unavailable. In spite of historical and theoretical social investigations in the causes of resource nationalism, rare studies engaged in quantification of dominant parameters of it. The objective of this study is to find significant factors that dominate the occurrence of resource nationalism for important metal and energy resources producing countries and quantify their marginal effects. The study applies binary choice logit model for panel data using pooled method. One feature of the research is that binary data set of occurrence of resource nationalism are sorted out by authors referencing U.S. Geological Survey’s reports. The results indicate that high-technology export (% manufactured export), ores and metals exports (% merchandise exports), rule of law (world governance indicator), trade (% GDP), and natural resource rent except forest (% GDP ) dominant the occurrence of resource nationalism for high and upper middle income group countries; government effectiveness (world governance indicator), policy perception index (The Fraser Institute), high-technology export (% manufactured export), and mineral rent (% GDP) dominant the occurrence of resource nationalism for lower middle and low income countries. According to our model, probability of occurrence of resource nationalism in 90 countries are predicted. Top 10 risky countries in 2012 are estimated to be North Korea, India, Honduras, Indonesia, Kazakhstan, Burkina Faso, Mongolia, Cuba, Bolivia, and Peru. The study is a primary trial of researching on resource nationalism and provides some insights for theoretical building and simulation on the issue.

Jan 1, 2017