Search Documents

By Robert S. Ondrey, Robert A. Haney, David J. Atchison

The Mine Safety and Health Administration has conducted tests to determine the effectiveness of two methods for reducing diesel particulate emissions in underground coal mines. Both methods involved collection of the particulate material before being released into the environment. One method utilized a disposable pleated paper filter attached to the tail pipe; the other utilized a reusable wire mesh screen attached to the tail pipe. This paper describes the instrumentation and testing used to evaluate both control methods. Results of respirable dust and diesel particulate measurements made underground are presented and analyzed.

Jan 1, 1992

By P. K. Sims

Extensive mineralization in the basal part of the Duluth Complex of Middle Proterozoic (Keweenawan) age in northeast Minnesota has been explored during the past 30 years as a potential source of copper and nickel from sulfide-bearing assemblages. Very large resources of low grade and marginal material have been delineated by drilling and by test shafts sunk by at least five private mining companies, but none of the properties has yet been mined. With few exceptions, grade and tonnage figures for specific properties have not been released, but the magnitude of the resources has been estimated by the Minnesota Geological Survey and the Minnesota Dept. of Natural Resources as constituting several billion tons of low grade and marginal copper- and nickel-bearing material - a major combined copper-nickel resource of international importance.

Jan 1, 1991

By P. M. Sandgren, H. Al-Dabbagh

Saudi Company for Precious Metals (SCPM) is jointly owned by the Saudi Arabian state organization Petromin (The General Petroleium & Mineral Organization) and Boliden of Sweden. The company operates the Sukhaybarat gold mine in the Saudi Arabian desert and produces some 80,000 ounces of gold per year by agitation and heap leaching. The discovery, development, and operation of this mine is a success story. After the first drill hole intercepted a gold mineralization in 1983, it took the partners only 8 years to delineate the ore reserve, locate water sources, prepare pre-and final feasibility studies, obtain permits, design, and construct the facilities. Sukhaybarat, which is an open pit mine, started off with a carbon-in-leach agitation plant only, but a heap leach facility was added in the beginning of 1995. Since start of operation in the middle of 1991, a total of 300,000 ounces of gold has been produced in the first four years of operation at a very competitive cost.

Jan 1, 1996

By T. A. Farr, I. A. Gibbs, F. Guevara, S. R. Simms, G. Nojima

This paper describes an installation of a medium-voltage adjustable frequency motor drive (AFD) on a high starting torque regrinding mill. This type of application is typically found in the mineral industry dealing with hard ore. The AFD electrical architecture is introduced from line to load. The type of closed loop encoder feedback motor control algorithm is briefly described. The results of the AFD motor identification auto-tuning are compared against the manufacturer’s supplied data. The motor drive performance results are shown for pre-ramp DC fluxing, high starting torque with overload current, excessive load torque stall condition, and blocked rotor. The instrumentation and arrangement for the two watt-meter method to capture low frequency data are presented. The data shown is from the input power quality meter, the AFD computer tool, the output motor protection relay, an oscilloscope, and load shaft connected strain gauge (rotating telemetry for torque assessment). These types of high starting torque constant torque loads are found in mining and process industry applications employing AC adjustable frequency drives. Using field results should help demystify the use of voltage matching output transformers in AFD applications including constant torque loads

Mar 2, 2022

By I. Yu. Melekestseva

Two types of hydrothermal massive sulfide fields were discovered in the Mid-Atlantic ridge (MAR) in the last twenty years. The first type associates with basalts and includes the TAG, Snakepit, Broken Spur, Lucky Strike and Krasnov hydrothermal fields. The second type is related to ultramafic rocks and represented by the Logatchev, Rainbow and Ashadze hydrothermal fields. In 2007 a new, probably, the largest cluster of hydrothermal massive sulfide field on the MAR (Fig. 1), related both to basaltic and ultramafic rocks, was discovered at 13°31'N of the MAR (Beltenev et al., 2007). [ ]

Jan 1, 2008

By Robert L. Virta

An asbestos substitute is any material that replaces asbestos in a commercial product. There are many asbestos substitutes, each with its own unique physical and chemical properties. Substitutes can be inorganic or organic, fibrous or nonfibrous, and natural or synthetic. They also can be used as a direct substitute for asbestos or as a replacement product. Probably in no other field is the diversity of substitute materials so great. The concept of asbestos substitutes is not new. The first major effort to develop asbestos substitutes was undertaken by the federal government. The United States has always been dependent on foreign sources for strategic-grade asbestos, and during World War II, the government was concerned that these supplies would be cut off. Strategic-grade asbestos was critical in many electrical and thermal insulation applications (electrical insulation, battery plate separators, flame-proof boards, insulation for rocket components, etc.). A reliable supply of nonstrategic-grade asbestos also was required for general civilian and military applications, such as in brakes, clutches, and construction materials. The government not only initiated a major search for deposits containing strategic-grade asbestos, it also funded research on synthesizing asbestos in the laboratory and developing products that did not contain strategic- grade asbestos. These efforts, as well as those conducted by the private sector, generally were unsuccessful. In the late 1960s and early 1970s, a second major effort to develop asbestos substitutes began because the general public was concerned about the health threat posed by the release of asbestos fibers during the manufacture, use, repair, and disposal of asbestos-containing products. Strict regulations covering the mining and manufacturing sector already had been enacted because of the issue of occupational exposure. The issue then became environmental exposures. Environmental regulations were enacted, and through time they became more strict. The combination of increasingly strict environmental regulation, maturing of some asbestos markets, and liability issues prompted many manufacturers to discontinue asbestos product lines or search for asbestos substitutes. As a result, asbestos usage dramatically declined from the 1970s to the present (Table 1).

Jan 1, 1994

By Roger P. Ashley

The main problem in geochemical exploration for gold ore bodies in the 40 km2 hydrothermally altered area at Goldfield is to decide which of the many silicified ledges exposed are most likely to yield deposits with additional subsurface exploration. We conclude that the most efficient way to search for exploration targets is to collect rock samples from the ledges and analyze for the following elements in decreasing order of priority: gold, lead and silver, bismuth, and mercury. These elements form relict hypogene aureoles restricted to the ledges and are not appreciably redistributed during supergene leaching.

Jan 1, 1978

By M Aboagye, K Appau, W. Assibey-Bonsu, C. Muller

A case study based on two recoverable resource modelling techniques (indirect and direct or localised methods) have been derived using typical feasibility study or new mine drilling data configurations from the extensions of an existing mine’s massive production database. The database is from the Gold Fields Tarkwa Gold mine (~6Moz Mineral Reserves and 13-year Life-of mine). The corresponding recoverable resources from the various techniques are then analysed using the open pit Whittle optimisation process. The results were then compared based on the Whittle optimisation results to determine the efficiencies of the approaches and the validity of the recoverable mineral resource estimates for mine planning and financial forecasts (including Cash Flows etc). Based on historical production metal recovery, the paper also assesses the corresponding orebody and mine planning as well as financial risks with regards to the modelling techniques. The study shows that the localized direct and somewhat more straight forward approach if applied efficiently can provide an equally useful tool for computing recoverable resources for mine planning and financial forecasts, as compared to the indirect approach as presently in use.

Jun 25, 2023

By Klaus Schönert

Experimental investigations of single particle and interparticle breakage show that the microprocess in mills demands an energy input between 1 J/g and 10 J/g, if particles below 100 pm have to be comminuted. A system analysis of grinding media and roller mills is given in respect to the energy supply to the microprocess and the influence of the back stream caused by the compression of the material inside the active volume. The back stream diminishes the probability for capturing the particles in very fine grinding processes. Some possibilities are discussed how to solve this problem.

Jan 1, 1989

By David Beck

In Australia, Safe Work legislation requires mines to have a documented ‘Safety Case’ explaining how a mine will safely manage all major hazards. A similar requirement is legislated or inferred by regulation in all jurisdictions. For small scale, instabilities leading to day-to-day seismic hazards, a ‘Stability Safety Case’ built around observational methods and measurement triggered responses can be effective because adverse situations are easily identified and the costs of lower control measures are not onerous. Also, if the influence of a volume of yield on the mine load system is small, the response of the system will be more predictable. However, for episodes of large scale mine instability, the hazard derives from the widespread, multi component influence of the event on the mine load system. As the system response depends on interactions between many parts, the resolution of predictions will be lower and situations can arise without local precedent. Further, as episodes of large scale instability change the stiffness and nature of the connectedness between parts of the mine load system, the behavior of the system before the event will be a poor empirical basis for forecasts of event related hazards. Most importantly, Triggered Action Response Plans (TARPs) and ‘traffic light’ warning systems cannot make design choices or identify new hazard phenomena. They are ‘lower’ control measures targeting explicit human-made instability hypotheses. As such, the Safety Cases related to management of hazard from potential large scale seismic events and mine instability cannot rely solely on TARPs. Mines that successfully manage meaningful dynamic instability always acknowledge the ultimate reliance on expert human intuition, knowledge and imagination to appreciate the range of possible hazard scenarios, to make stability hypotheses and propose solutions. Complex analysis, TARPs and measurements are critical steps in the human decision cycle, but only support the making and testing of ‘Stability Hypotheses’ made by expert engineers. Relying on expert skill and judgement as essential components of a Safety Case, however essential, introduces human vulnerabilities. Another challenge is that the expert decision making process is hard to document. Beck et al 2019 first described an organizational and procedural framework for maintenance of an ongoing large-scale ‘Stability Safety Case' where a degree of expert judgement and imagination is needed to manage a seismically active mine. The structured data appreciation process outlined sufficient measurements, analysis and appreciation to confirm the stability state of the mine and was applicable to all underground mines. After several years of implementation in various forms in stoping, caving and room and pillar mines, this update addresses lessons learned and describes some considerations for numerical forecasting to establish a base case, and some challenges for empirical hazard identification.

Apr 26, 2022

By D. W. Park

Longwall mining is considered the most efficient underground coal mining technique in terms of coal extraction ratio, production rate, and safety standards. Due to the increasing demand for higher coal production, wider panel and faster face movement have become the recent trends. Thus, longwall mining can create unexpected threats such as roof falls, excessive face convergence, shield damage and numerous maintenance problems causing sudden interruption of coal production and serious safety hazards. A recent study at the University of Alabama is dedicated to develop LoSCoMS (Longwall Strata Control and Maintenance System) which integrates real-time shield monitoring, data presentation, analysis, forecasting, and warning modules. The main objectives of this system is to provide the stability and maintenance information, at every minute, such as high load, low setting pressure, leg leakage, etc., analysis of various mining and geological parameters to determine past and present roof characteristics and forecasting of loading patterns for the following mining cycles, next periodic weighting, etc. Using this unique system, mine operating personnel are well aware of past, present and future roof loading patterns at the longwall face, and thus, proper safety measures can be taken ahead of time.

Jan 1, 1997

By J. W. Leonard, C. L. Jiang, B. K. Parekh, X. H. Wang

The selective depression of pyrite from the Kentucky No. 9 coal seam was systematically examined using various kinds of inorganic and organic chemicals. Most of the organic chemicals tested showed little selectivity in pyrite depression. It was found that both orthophosphate and pyrophosphate were effective for the selective depression of coal pyrite in coal flotation using fuel oil as a collector. At substantially low concentrations of pyrophosphate, the flotation of coal pyrite was completely depressed over a wide pH range, while the coal flotation remained unaffected. The mechanism of the selective depression of pyrite by phosphates was explained with the help of thermodynamic calculations of iron-phosphate-water systems and zeta-potential measurements. It was shown that pyrophosphate reacts strongly with the iron ions of pyrite to form stable hydrophilic iron pyrophosphate complexes on pyrite surfaces.

Jan 1, 1999

The 71st Annual Meeting of the Minnesota Section of SME and the 59th Annual University of Minnesota Mining Symposium were held jointly April 14-16, 1998, in Duluth, MN. Registration was estimated at 450 people, about the same as last year's attendance. A short course on mine productivity and a trade show that included about 75 exhibitors were also held in conjunction with the SME meeting. This year's theme was "Iron ore and integrated steel - where are we going?" Although generally optimistic in the near term, the general feeling among the attendees is that the industry faces serious competitive challenges. The iron mining industry in Minnesota experienced a tremendous rebound from the devastating downturn of the 1980s. Today, however, all seven of Minnesota's taconite plants are operating at full capacity. And these high production levels are expected to continue during the next several years. Longer-term, however, Minnesota's producers face an increasingly competitive worldwide market, including stiff competition from Canadian operations. Because of the increasing competition, industry representatives in Minnesota believe that it is critical to strengthen their operations. To accomplish this, companies are looking to: ? Further reduce production costs. ? Bring new technologies into their operations. ? Develop value-added facilities such as direct-reduced iron. ? Expand their markets. The industry is also seeking more collaboration between industry and government. The National Steel Pellet Co. and Minntac are looking at using ported kilns, which would reduce energy consumption significantly. Cleveland Cliffs, EVTAC, Northshore Mining and Minnesota Iron and Steel are all looking at building value-added plants. One such project that received attention among the attendees was Minnesota Iron and Steel's proposed $1.2 billion combined mine, taconite plant, direct reduced iron facility and steel production facility. If the operation is built, it would produce about 3.4 Mt/a (3.39 million ltpy) of direct-reduced iron pellets. Financing is pending. An announcement is expected in the fall of 1998. The pellets, containing 70% iron, would be processed into steel in electric arc furnaces. The steel produced would then be processed into hot-rolled coil, which is used by the appliance and automobile industries. The keynote addresses and technical sessions focused on these issues as well as on environmental issues.

Jan 1, 1998

By Ryan Dr.

In December 1988 Phelps dodge corporation brought an underground gold mine into production in the republic of Botswana. The mineralization is associated with steeply dipping shear zones in Archean greenstones of the Tati Schist Belt. The gold is intimately associated with sulfides and is refractory in nature. The deposit is being exploited by underhand open stoping methods. Vertical and inclined shafts are used to hoist the ore to surface where it is treated by conventional crushing, milling and flotation, followed by fluid bed roasting with CIP elution and carbon regeneration. Adjacent deposits are being explored with a view to increasing production. Legal and taxation aspects of operating in Botswana are discussed.

Jan 1, 1989

By Gustavo G. Pilger, Jair C. Koppe, João Felipe C. L. Costa

Information for mine planning requires to be close spaced, if compared to the grid used for exploration and resource assessment. The additional samples collected during quasi-mining are frequently located in the same pattern of the original diamond drill holes net but closer spaced. This procedure is not the best in mathematical sense for selecting a location. The impact of an additional information to reduce the uncertainty about the parameter been modelled is not the same everywhere within the deposit. Some locations are more sensitive in reducing the local and global uncertainty than others. This study introduces a methodology to select additional sample locations based on stochastic simulation. The procedure takes into account data variability and their spatial location. Multiple equally probable models representing a geological attribute are generated via geostatistical simulation. These models share basically the same histogram and the same variogram obtained from the original dataset. At each block belonging to the model a value is obtained from the n simulations and their combination allows one to access local variability. Variability is measured using an uncertainty index proposed. This index was used to map zones of high variability. A value extracted from a given simulation is added to the original dataset from a zone identified as erratic in the previous maps. The process of adding samples and simulation is repeated and the benefit of the additional sample is evaluated. The contribution of an extra sample was evaluated locally, globally and in terms of variation in total measured resources. The procedure showed to be robust and theoretically sound, mapping zones where the additional information is most beneficial. A case study using coal seam thickness illustrates the method.

Jan 1, 2002

By Michael Murphy, Mark Van Dyke, VASU GANGRADE, Brent Slaker

Room-and-pillar mining in multi-level underground stone mines come with unique pillar stability issues. The pillar stability in these mines primarily depends on the thickness of interburden between mining levels and the staggering of pillars. NIOSH has previously established pillar design guidelines for shallow, flat-lying mines and single-level operations, but there is little guidance for ground control design in multiple-level stone mines. Therefore, to improve the overall understanding of ground control in these mines, a microseismic monitoring system has been installed at a multi-level underground stone mine in Tennessee with up to a 243-m overburden and a 7-m interburden thickness between levels. The microseismic system is comprised of nine uniaxial accelerometers and one triaxial accelerometer installed in the interburden. The seismic array is locally focused with all sensors installed within a 625 m2 area and is setup to monitor the seismicity around the formation of the pillar in the lower mining level. Data is collected over 11 months and comprises of over 1,000 high-confidence events that have been located in the study area comprised of post-blast activity. The event locations were identified using a 3D-velocity model, with an average 4-m location accuracy for this array calculated using the system data. Most observed seismicity was on the excavation boundary, both in the interburden and in the roof of the top level. At this stage of analysis, there are no significant rock failures with which to correlate seismicity, but event locations correlate well with presumed damage in the vicinity of blasts.

Apr 26, 2022

By W. D. Monaghan, A. J. Kwitowski, A. L. Brautigam

Teleoperation is a technology that can provide significant health and safety improvements in mining operations by locating machine operators hundreds of meters away from the face area. The US Bureau of Mines recently developed a teleoperation system for continuous mining and haulage equipment. This system features near real-time closed-loop control. A prototype system was developed and demonstrated. This system could be used in thin-seam applications down to 36 in (914 mm). Provided are details of the teleoperation system, the results of testing and the expected applications of this technology.

Jan 1, 1996

By J. Noll, J. A. Organiscak, A. B. Cecala

"In recent years, significant strides have been made to optimize the design of filtration and pressurization systems used on enclosed cabs of mobile mining equipment to reduce respirable dust and other contaminants and provide the best air quality to the equipment operators. This synergetic effort has involved original equipment manufacturers building mining equipment, manufacturers of heating, ventilation, and air conditioning systems for mobile equipment, filtration and pressurization system manufacturing companies, as well as the National Institute for Occupational Safety and Health, and other government organizations. Considering all the advances made in this area over the last decade, one aspect that NIOSH still needs to assess is the longevity of optimal cab performance with respect to the quality (filtering efficiency) of the filters used in filtration and pressurization systems. In today’s culture, most health and safety professionals automatically believe that HEPA quality filters need to be used to provide the greatest level of protection to workers. Researchers at the Office of Mine Safety and Health Research for NIOSH hypothesized that HEPA quality filters may not be optimal for the mining industry and speculated that MERV 16 rated filters would be more appropriate in most cases. In order to test this hypothesis, NIOSH performed a two-year study comparing both HEPA and MERV 16 quality filters on two pieces of underground limestone mining equipment, being a roof-bolter and face drill machine. Testing showed at the 95 pct. confidence level that there was no statistical difference between the two efficiency filters on both pieces of mining equipment. Since the MERV 16 rated filters were less restrictive and provided greater cab pressure, and since they did not have to be replaced as often as the HEPA quality filters, researchers concluded the MERV 16 filters were the optimal choice for both pieces of mining equipment in this case study comparative analysis. INTRODUCTION When most health and safety professionals today think about filtration efficiencies and their correlation with protecting workers’ health, the normal assumption is the higher the efficiency of a filter, the greater the protection afforded to the workers. The next logical step is to believe that HEPA filters deliver the greatest protection for workers because they provide the highest filtering efficiency. Obviously high-efficiency intake filters are a necessity for an effective cab filtration and pressurization system on mobile mining equipment, but what is the optimal filter efficiency rating for achieving high levels of cab protection factor performance over the service life of filters? To address this question, the National Institute for Occupational Safety and Health (NIOSH) has performed an in-depth laboratory research study over the years simultaneously with numerous field studies to retrofit used enclosed cabs on mobile mining equipment with newer and more effective filtration and pressurization systems."

Jan 1, 2016

By K. A. Natarajan, M. K. Yelloji Rao

The electrochemistry of sphalerite and chalcopyrite was investigated under both open-circuit and applied potential conditions. Emphasis was placed on the selective dissolution of sphalerite from a mixture of sphalerite-chalcopyrite flotation concentrates as a function of applied potential, acid concentration, pulp density, and time. Morphological studies using a scanning electron microscope (SEM) were also carried out with chemically leached, galvanically leached, and unleached surfaces of sphalerite and chalcopyrite. Selective dissoulution of sphalerite could be achieved if the mixed chalcopyrite-sphalerite concentrate slurry was maintained at a negative applied potential of -0.4V (SCE). Probable mechanisms involved in the selective dissolution of zinc are disscussed.

Jan 1, 1990

By S. D. Thompson

Several discrete-event simulation models have been developed for designing the conveying system capacities of underground coal mines. Most of these models require the use of a step function approach to mimic the loading process at each conveyor loading point. Over the years, practitioners have generally employed one of three versions of the step function approach. An important issue is how these three versions compare to each; other in terms of simulated capacity requirements for belt conveyors. Another issue is how they compare to the peak capacity design. This paper addresses these issues by statistically and quantitatively comparing their simulation results. The consequences and problems associated with using each version are also discussed and summarized.

Jan 1, 1997