Search Documents

By V. Srivastava, T. Ghosh

The modeling and simulation of semiautogenous (SAG) mills have been widely used in the design and optimization of mill performance in terms of its power draw, processing capacity and product size distribution. However, these models are solved under steady approximation and do not provide any information on mill charge distribution in real time. 7KLVSDSHUDWWHPSWVWRFKDUDFWHUL]HPLOOFRQWHQWVE\VROYLQJ:KLWHQ¶V¿UVW RUGHUFRQWHQW EDVHGPRGHOLQWKH0$7/$% Simulink environment. The parameters in the model, such as breakage rate constant, discharge rate and appearance function, were estimated using process and design data collected from a gold mine operating in Alaska coupled with a nonlinear parameter estimation scheme. This model was then used to predict the dynamic responses of other key operational variables, such as mill power, bearing pressure, charge level and product size distribution. The transient response of mill behavior with respect to changes in feed size distribution, tonnage and mill feed water is also presented. This dynamic simulation approach can be used for practicing different control strategy and training purposes. The observed response of mentioned variables was validated using dynamic response data from the plant to encompass operational characteristics of SAG mill behavior.

By Rainer Antretter

The city of Garmisch-Partenkirchen in southern Germany is located at a main transit road to Tyrol in Austria and suffers of a very heavy traffic load. Therefore, the Kramertunnel as a by-pass tunnel is built to release/mitigate the traffic through the city centre. The 3,600 m long single tube road tunnel is designed with a parallel but smaller emergency tunnel and with cross passages, fitted with single- and doublesided emergency bays, a vent shaft, and an intermediate ceiling to separate fresh air supply from the road traffic. The tunnel, concrete lined along its entire length provided the challenge to find smart formwork solutions for quick set-up, repositioning, setup and pouring. Three particularly specific sections are discussed in this paper.

Jun 13, 2023

By Hans Adden, Anne Lehan, Markus Thewes

"1. INTRODUCTION AND MOTIVATION Traditionally design processes are focussed at creating new tunnels for lowest building cost. But the trend towards sustainable constructions in tunnelling has greatly increased in recent years. A critical subtask of this approach is to realize the potential for optimizing and reducing the life-cycle costs (LCC) of tunnels and their components. To evaluate underground infrastructure projects from an economic point of view is therefore a highly topical subject of public authorities as well as private companies participating in Public Private Partnerships (PPP) projects. Nowadays, in the case of public works contracts, the contracting authorities shall draw up rules not only for the design but also for life-cycle costing. Within the scope of the decision-making process of building a new tunnel, planning the maintenance activities or the refurbishment of a tunnel in operation, the decision-makers need detailed knowledge about the current and future financial conditions of the planned projects and selected sub-measures. But in practice, the initial costs still represent the primary decision criterion in the planning phase, whereas the subsequent or follow-up costs, respectively, are only estimated roughly. Although tunnels are the key components and the most costly parts of the transport infrastructure, only a small number of scientific papers deal explicitly with the calculation of life-cycle costs for underground infrastructure. And in these cases, most authors use as the starting point only the basic form of the Net Present Value method which is known as the frequently applied life-cycle costing technique in building construction. The present study explains the strategic concept of life-cycle costing and its fundamental instruments for operational implementation. It shows the necessity to take into consideration that there are fundamental methodical problems when the life-cycle concept is transposed without modifications from building construction to civil engineering. The paper will discuss in detail some selected associated problems with the net present value method. On the basis of operational and safety related tunnel equipment it is shown, what impact this may have on principle determining the LCC of tunnels. Selected best-practices of maintenance planning for tunnels undertaken by the German Ministry of Transport fill the theoretical approach of the concept with life and give a practical orientation. In particular government authorities but also construction companies are interested parties in modern cost management considerations. The reason for this development is the replacement of aged excisting structures and the advancement of technical standards. The increase in the total numbers of tunnels (Fig. 1) as well as the need for future re-investments in existing tunnels show the overall economic impact and justify the change towards the life-cycle perspective."

Jan 1, 2016

By E. Milosavljevic, C. H. Bucknam, K. L. Gabby, T. C. Eisele

"Since mercury is chemically similar to silver, it tends to dissolve along with the silver and gold during cyanide leaching. Ultimately, mercury is recovered along with the silver as mercury/silver/gold amalgam, which requires retorting to remove the mercury prior to refining the silver and gold. A possible approach to separating mercury from silver and gold in cyanide leach solutions is to take advantage of the replacement reaction between [Hg(CN)4]2- and Ag2S, which results in precipitation of mercury as HgS while dissolving silver as [Ag(CN)2]-. Results are presented demonstrating that mercury can be removed from cyanide solutions with high effectiveness while, at the same time, recovering additional silver in solution. Initial experiments with static flasks in the laboratory showed a high degree of mercury removal could be achieved. Results using actual metallurgical plant products in bottle roll tests indicate the process works on a larger scale, but also results in significant gold losses if the solution being treated has high gold levels, such as carbon stripping pregnant eluent solution. IntroductionThe dissolution of mercury along with precious metals during cyanide leaching is a long-standing problem, which can result in significant mercury toxicity issues (Washburn, 2003). Mercury is first dissolved by the cyanide solution, and then, since it has a great deal of chemical similarity to silver, it follows silver throughout the concentration and recovery processes, ultimately being recovered as a silver/ mercury amalgam when the metal is precipitated by either the Merrill-Crowe process or by electrowinning.While it would be desirable to either prevent mercury dissolution entirely while still allowing silver dissolution, or to selectively capture mercury before the precious-metals recovery step, there is not yet an effective and economically practical approach to doing this (Grosse, 2003; Ravichandran, 2004; Misra, 1998; Pai, 2000). There are a few processes that have been proposed, such as differential adsorption. While activated carbon, as used in the carbon-in-pulp process, is not highly selective between mercury and silver (Washburn, 2003), it may be possible to achieve some separation by selective elution of the carbon to produce high-mercury and low-mercury eluates (Bunney et al., 2010). Certain synthetic resins were shown to be selective for gold but are more expensive than carbon, requiring special equipment, and have not yet been shown to be selective for mercury (Grosse, 2003). There may be potential for differential dissolution approaches, as thiosulfate leaching does not dissolve mercury sulfides as readily as it dissolves gold (Oraby et al., 2010), and it is possible that it may be similarly more selective for dissolving silver relative to mercury. Some work has also been done with selective precipitants, such as sodium polythiocarbonates (Bucknam, 2007), and 1,3-benzenediamidoethanethiol (Matlock, 2002). Common problems with these approaches include introduction of a solid:liquid separation step, reagent costs, the need to measure the mercury concentration for process control for minimizing silver losses, and regulatory requirements to retort otherwise stable mercury concentrates."

Jan 1, 2015

By W. Kennedy Gauger, Tim Oolman, Debra L. Bisson

Radian Corporation (Radian) has developed a process for treating Cr(V1)-contaminated soils that involves: 1) soil washing using an alkaline extractant, 2) biological reduction of Cr(V1) to Cr(II1) in the soil wash effluent, and 3) separation of Cr(II1) from the biologically treated effluent. Biological treatment has been demonstrated for immobilized cells in fluidized bed bioreactors and suspended cells in slurry bioreactors for Cr(V1) levels ranging from 30 to 600 mg/L which have been reduced to non-detectable levels (< 0.05 mg/L; method detection limit [MDL]) during hydraulic residence times as short as 12 hours. The resulting Cr(II1)-containing effluent stream was chemically treated to precipitate chromium hydroxide for removal by physical separation.

Jan 1, 1995

By M. W. Harmer, J. M. Quist

Laboratory test work, pilot plant testing and plant experience with wet, fine-mesh screens are discussed. High-frequency, low-amplitude, fine-mesh, wet screens were installed on the 6th cleaner concentrate stream. These screens produce a 60% oversize recovery split of the molybdenite concentrate that is of leached equivalent quality. The undersize stream is leached with hot ferric chloride to remove lead and copper contaminants before roasting or shipment to sulfide customers. This plant modification is a good example of using existing technology in an unconventional flow sheet to yield significant cost savings.

Jan 1, 1991

A computer simulation of the automatic control of continuous mining machines has been prepared, similar to previous simulations of longwall mining systems and coal thickness sensors. The simulation allows for programmed variation of the horizon detection method, the azimuthal guidance system, the type and configuration of the miner, varying hardness in the unmined face material (leading to varying error in the machine heading), and the miner&apos;s cutting cycle. It simulates control of the miner in three axes. Use of the simulator makes it possible to anticipate problems arising from the complex character of underground mining, which include unpredictable multi-pass coupling and unpredictable variation in geological conditions.

Jan 1, 1993

By A. M. Laird

Endako Mines&apos; molybdenum operation is located near the geographic center of the province of British Columbia, Canada. The property is six miles south of the Northern Transprovincial Highway and the northern main line of the Canadian National Railway. The area is broken by high hills covered with dense stands of spruce and pine with vast areas of the valley floors covered with aspen and poplar. The climate is moderate with precipitation averaging 22 inches per year. Approximately four feet of snow accumulates in the winter, and temperatures range from 900 F. in summer to -40° F. in winter. The orebody, a lowgrade porphyry type deposit, occurs in a widespread granitic intrusive which has been locally weakened at the intersection of two regional faults. In this vicinity the quartz monzonite has been further shattered to permit the entry of mineralizing solutions and local dykes. Two types of mineralization occur within the orebody. The most prom¬inent is the six inch to four foot wide continuous quartz veins with characteristic ribbons of molybdenite and frequently finely-divided grains of molybdenite within the quartz. The second type occurs as fine fractures filled with quartz molybdenite in the form of a stockwork halo radiating out from 20 to 200 feet from the quartz veins. Minor hematite, magnetite and chalcopyrite are also present. Mineralization is roughly proportional to the extent of kaolinization in the quartz monzonite, kaolinization being one of three distinct forms of hydrothermal alteration. Pyrite is commonly associated with molybdenum mineralization within the orebody and a pyrite halo is recognized on the south side of the orebody.

Jan 1, 1968

By A. D. Wunderlich

Providing a safe & secure environment for your employees and other company assets is absolutely necessary in our litigeous society. Security hardware is no different than computers or other technical equipment, in that new equipment is developed each year that makes older equipment obsolete. This presentation will help to explain how your existing security system and security procedures can be updated to meet industry standards without the expenditure of a great deal of money. If you are concerned about potential security problems and how to address these problems, this presentation is a must.

Jan 1, 1995

By William E. Wallace, Michael J. Keane

This review summarizes three sets of ongoing studies which we are performing in collaboration with a number of researchers associated with the Dept. of Interior - Generic Mineral Technology Center for the Study of Respirable Dusts, concerning surfactant-particle interactions studied using this surrogate surfactant. These topics are: (A) the suppression of mineral particle cytotoxic potential by DPL adsorption and the persistence of this effect under conditions of enzymatic digestion; (B) surfactant suppression of organic particle cytotoxicity by DPL adsorption and the effect on subsequent expression of genotoxic potential; (C) potential effects of surfactant on heterogeneous structured complex respirable particles. The references list some of our reports which can provide additional information on these studies. Further, those reports provide references to the literature of the field and to the works of others on these topics. Deep lung airspaces, the pulmonary alveoli and respiratory bronchioles, are coated with a hypophase which is rich in surfactant biomolecules secreted by the alveolar type II epithelial cells. The surfactant is known to be critical to maintaining stable low surface tensions on the inner surfaces of the alveoli by forming a surfactant layer on the airliquid interface of the alveolar hypophase. Upon deposition in the acinar regions of the lung a respired particle&apos;s initial contact will be with this surfactant coating over pulmonary tissue. A primary component of this surfactant is the phospholipid diacyl glycerophosphorylcholine, commonly called lecithin. A surface layer of dipalmitoly lecithin on saline will act much as full pulmonary surfactant in decreasing surface tension and producing a hysteresis in surface tension behavior with surface area. We have used dipalmitoyl glycerophosphorylcholine, or dipalmitoyl lecithin (DPL), a major component of that surfactant, dispersed in physiologic saline as a surrogate for studying interactions of both mineral and organic respirable particles with pulmonary surfactant and consequent effects on particle toxic behavior. A. DUST CYTOTOXICITY AND LECITHIN SURFACTANT ADSORPTION Respirable quartz and kaolin clay particles are found to be comparably cytotoxic in a number of in vitro bioassays including lavaged rat pulmonary macrophage release of cytosolic and lysosomal enzymes, and red blood cell hemolysis as a measure of dust membranolytic potential. These direct and prompt cytotoxic activities do not account for the distinctly greater potential for quartz to induce pulmonary disease. When respirable quartz and kaolin are incubated with a dispersion of DPL in saline at 37C it is found that the prompt cytotoxicity of both dusts is fully suppressed as measured in vitro by pulmonary macrophage release of lactate dehydrogenase, beta-N-

Jan 1, 1991

By Zoheir Khademian, Gabriel S. Esterhuizen, Morgan Sears

Based on the 2010-2019 Mine Safety and Health Administration (MSHA) accident report database, 91% of reported ground control accident in the US longwall mines were caused by gateroad roof instability. This can be related to the significant changes in loading conditions that gateroads are subject to from the development to the longwall abutment loading phases, combined with the thinly bedded shale roof, found in many US longwall coal mines. One of the challenges in designing efficient support systems is to understand the roof instability mechanisms along with support-roof interactions under this complex loading condition. Field monitoring of roof displacement and stress changes coupled with detailed analyses using numerical models are well-documented techniques to study the causes of roof instabilities. However, traditional modeling techniques require additional calibration to simulate delamination and buckling of shale roof, one of the main roof instability mechanisms in longwall mines. One alternative modeling technique is the UDEC Bonded Block Method (BBM) where bedded roof and support interactions can be explicitly captured. This paper presents the development of a BBM model of a longwall entry at a 180 m depth of cover with a three-entry gateroad layout along with roof extensometer monitoring results. The models are validated against the monitoring data, showing the potential for BBM numerical models capturing the complex roof and support system interactions to assist with optimizing gateroad layouts and support systems.

By J. K. Ahlness

The US Bureau of Mines investigated technologies for determining the integrity of in situ leach mining wells. A self-contained trailer-mounted well integrity testing system (WITS) was designed and built to enable rapid testing of well casings for leaks as required by environmental regulations. The WITS utilizes two inflatable packers to seal off the entire casing length or any portion thereof. Water pressure is built between the packers to the desired test pressure, and the presence or absence of casing leaks is determined by monitoring the pressure drop between the packers. A winch and steel cable are used to run the packers in and out of the well. The WITS underwent an industry field test at the Irigaray in situ uranium leaching mine near Buffalo, WY. A total of 37 wells with an average depth of 69 m (225 ft) were tested at an average rate of four wells per eight-hour shift with a two-person operating crew. This represents a 75% time savings and an 83% labor savings compared to the rigid-pipe method previously used at the mine, with which a three-person crew tested an average of one well per shift.

Jan 1, 1988

By Yueyue Ding, Yuanhui Li, Zhengrong Li, Pengfei Yu, Kunmeng Li, Zhipeng Xiong

The stress evolution and failure characteristics of overburden were studied during multi-stope mining for a gently inclined thin orebody. Firstly, an indoor physical experiment was conducted on the excavation of a multi-stope mine with an orebody dip angle of 20°. The results show that the vertical stress concentration area gradually shifts to deep-buried rock mass with the mining from shallow to deep buried stopes, resulting in shear failure originating from high stress. On the contrary, the pressure relief zone presents an asymmetric distribution characteristic that is biased towards the upper part of the goaf, resulting in large subsidence and tensile failure of the stope #1 and #2 roofs. Secondly, the numerical simulation model under the same geological condition was established to measure the roof deformation at different stages of mining. The numerical simulation results are in good agreement with the physical test results; the roof displacement is largest in stope #2, second-largest in stope #1, and smallest in stope #3. Finally, the evolution of deviator stress concentration, displacement field and potential failure zone of overburden under different orebody dip angles were studied. As the dip angle of the orebody increase, the deep-buried stope roof changes from deviator stress release to deviator stress concentration in different stages of mining, and shear failure is most likely to be induced when the orebody dip angle is 30°. Meanwhile, the closure displacement of the stope roof decreases gradually, while the tangential displacement increases, so the anti-sliding ability of the support bodies in the stope should be improved. The potential tensile failure zone gradually shifts from the center of the goaf to the upper part, and the deep-buried stope roof evolves from tensile failure to shear failure. Results of this research expected to provide guiding significance for stope support design to control roof deformation and failure, to ensure the safety of the stope.

Mar 2, 2023

By J. Holmes Armstead, John L. Dobra

This paper examines some lesser known risks in foreign investment by U.S. companies that derive from international judicial activism by U.S. courts and the potential for extending U.S. anti-trust regulations to companies&apos; foreign operations. The discussion of international judicial activism reviews the implications of the U.S. Second Circuit Court&apos;s ruling in the Union Carbide/Bhopal case for U.S. companies investing abroad and the discussion of extending U.S. anti-trust regulations focuses on proposals coming out the Clinton administration&apos;s Justice Department.

Jan 1, 1996

By Yuanping Chen, Yihui Zhao, Yunhe Hong

It is important to study the methane transport phenomenon in a longwall panel under descentional ventilation conditions. The gob area is divided into a number of rectangular percolating elements, each of which is connected with its neighbors by leakage passages, so that a network can be formed. Using the mechanics of porous media fluid flow, the mathematical model of air and gas flows can be established. Based on the existing ground pressure theories, the inhomogeneous porosity of the porous media in the gob can be given. Through computer simulation it is found that air pressure and temperature are functions of position. Air density, viscosity, and natural ventilation pressure are functions of temperature, pressure and methane concentration. It is also found that the resistance varies with air density and viscosity. Finally, the calculation results are given to show the differences between ascentional and descentional ventilation methods.

Jan 1, 1991

By X. P. Zheng, H. K. Lin

During slow-cooling crystallization of iron-making blast furnace slags, most rare earth elements recrystallize in an artificial "mineral" identified as calcium cerite. Scandium (Sc) and europium (Eu), however, concentrate in a sheetlike "mineral." In this investigation, the mineralogy of this sheetlike "mineral" was studied. It was identified as being in the mica group and was called a rare earth-bearing barium fluorophlogopite. One of the objectives of this study was the recovery of this "mineral." The study indicated that it can be effectively recovered from the slag by flotation using dodecylammonium acetate or a combination of dodecyl-ammonium acetate and sodium oleate as collectors.

Jan 1, 1998

By Rolando V. Cuaño

For geostatistical applications, heterogeneous spatial phenomena are better modeled as mixtures of populations. However, the modeling of the constituent populations can become complex. The alternative mixture model offers a simplified approach to the w modeling problem. The model is applied and tested on the Walker Lake data set. Compared to the univariate ordinary kriging model, the alternative model generates less biased block estimates.

Jan 1, 1996

By J. L. González-Chávez, A. Ballester, M. L. Blázquez, F. González

In recent years, the bioleaching of sulfidic raw materials has been of great interest. However, the application of this biotechnology is now very limited for many different complex reasons. The mechanism of the chemical and electrochemical reactions taking part in the process is not well understood. The application of electrochemical techniques is useful in its elucidation. Among the common sulfides, galena has been studied very little with respect to its behavior during bioleaching. Therefore, the electrochemical evolution of massive electrodes of lead sulfide in the presence and absence of&apos; a mixed culture of mesophilic microorganisms was investi¬gated by the application of potentiometry, anodic and ca¬thodic polarization and cyclic voltammetry. The agitation rate, the use of pH control and the composition of the nutrient mediums did not have any significant affects on the oxidation of galena. However, the temperature (25 &apos;to 45 °C), the scan rate (4 to 100 mV/s) and the acid used to adjust the pH were significant variables that influenced sulfide oxidation. There¬fore, the peak (600 to 1,000 mV) corresponding to the oxida¬tion of sulfide ions from the mineral was only detected in the presence of a complexing anion of lead. In the presence of bacteria, the peaks corresponding to galena oxidation de¬creased and, at the same time, new peaks appeared both during the oxidation at -300 mV and during the reduction of the mineral surface at 150 and -300 mV. These signals were more important when the attack time increased. The rest potential of bioleached mineral increased with an increase in leaching time, which was related to the electrochemical transformation of the galena surface.

Jan 1, 2000

By Ernest Peters, Fiona M. Doyle

The leaching and bulk decomposition of sulfide minerals is of enormous commercial importance in several areas of the minerals industry. These include: direct leaching of ores or concentrates for the recovery of the contained metal values; decomposition of sulfides to recover associated values such as encapsulated gold; and the potentially hazardous oxidation of sulfides in waste disposal facilities. A significant challenge to successful future developments in these areas is to improve our fundamental understanding of the mechanisms of the chemical, electrochemical, and bacterially-mediated interactions between sulfides and aqueous solutions. The paper summarizes current understanding of these mechanisms, and discusses promising new directions for research.

Jan 1, 1989

By P. Oghazi

It is possible to have traceability in the mining industry, by parameters and signatures like particle mineralogy, mineral association, texture and mineral liberation. The study is on an apatite-iron ore deposit at Malmberget, Sweden, and characterizes an ore body both mineralogically and texturally in a quantitative manner by using analytical methods like optical microscopy, microprobe (EMPA) and an automatic SEM based system, Particle Texture Analysis (PTA). The mineralogy was evaluated by PTA and characterized by modal mineralogy, mineral liberation and mineral associations. Magnetite has a simple outline and straight grain boundaries and the gangue minerals have a finer particle size with a more complicated texture. The PTA analysis also shows that apatite is associated to magnetite as mixed particles, while smaller grains of magnetite are inclusions in feldspar. Result from particle texture analysis shows that there is a connection which link to the mine-to-mill context, and it may be used to create traceability. This link is not the associations of the main ore mineral magnetite, nor the modal mineralogy. Instead, it is the mineral associations of contaminating minerals (apatite and feldspar) that appear to be most promising since they survive from mine to mill. The modal mineralogy may be used to understand how contaminated minerals break into or out of particles size fraction during grinding.

Jan 1, 2010