Search Documents

By S. Bozinis

In this paper, blast design considerations and implementation that lead to reduced vibrations will be presented. In addition, blast vibration data collected during hard and semi-hard rocks blasting in the proximity of an inhabited area will be analyzed and presented. In all cases maximum vibration levels are kept below the limits set by DIN 4150.

Jan 1, 2006

By D. M. Bodily, M. D. Deo, E. M. Whitney

Field data from coalbed methane wells indicate a significant variation in composition as a function of flow rate and time. In particular, San Juan Basin wells have displayed an increase in C02 concentration over time. Prediction of gas quality is critical to the economic evaluation of any coalbed project. Previous models have forecast only pressure and production profiles, ignoring compositional variations. In this study a multicomponent model that incorporates binary isotherms for methane and carbon dioxide has been developed. An extended Langmuir isotherm is used for the adsorption representation and a constant separation factor (similar to relative volatilities in distillation) describes the phase distribution of the species. This separation factor depends both on the surface characteristics of the coal and on the adsorbing species. The chromatographic separation equations have been superimposed on Darcy's law flow. The formulation allows decoupling of the pressure and compositional partial differential equations. The equations have been cast in dimensionless form and solved for pressures and compositions. It is observed that the composition of the preferentially adsorbed C02 increases at the wellbore as a function of dimensionless time. The dimensionless time is directly proportional to the real time and coalbed permeability and is inversely proportional to the gas viscosity, coal porosity and the square of the length of the reservoir. As the separation factor increases, the compositional variation increases. This variation in produced C02 concentration is also greater when the initial C02 concentration in the reservoir is higher. A sensitivity study has been performed to identify the effects of important parameters such as isotherm variables and reservoir characteristics on pressure and composition profiles.

Jan 1, 1993

By Y. Astafyev

Autotransport is one of the most conventional kinds of transport in iron ore open-pits. It. is successfully used both independently and in combination with other kinds of transport. In the Krtvoy Rog Basin open-pits annual truck transportation accounts for more than 235 million tons of ore and waste rock. In the process of operation trucks make up various transport streams depending on - the development of autoroads in the open-pits; - the capacity and the number of loading equipment ; - the load carrying capacity and the speed characteristics of trucks

Jan 1, 1979

By M. Schultz

The cost of remediation often drives the selection of the preferred remedial alternative at hazardous waste sites. The use of probabilistic cost/risk analyses can aid in predicting costs of remedial alternatives. Three types of information are discussed in performing cost/risk analyses: (1) data on the quantity of contamination versus the contaminant concentration; (2) unit costs of remediation for the remedial alternatives; and (3) risk to contaminant concentration relationships. Cost/risk evaluations are performed on a site-by-site basis, to account for combined risks of different contaminants and differences in quantity to be remediated versus contaminant concentration. The cost/risk analysis produces a graph of risk versus cost for each of the remedial alternatives. These costs are then compared to facilitate selection of a preferred alternative. An example of comparison of alternatives is illustrated for a historic coal gasification site.

Jan 1, 1992

By William Gleason

"In 2008, the world quietly hit a milestone that did not receive much fanfare or publicity, but it hit one that marked a turning point in the history of mankind and the way the planet is and will be inhabited in the future. It was in 2008 that, for the first time, more than half of the world’s population, an estimated 3.3 billion people, resided in urban areas. The world’s population had moved from being a majority of agricultural and rural society to an urban society. Andrew Whalley, deputy chairman for Grimshaw Architects, said this change in where and how people live will continue to increase urban populations and, by 2050, it is estimated that more than 6.4 billion people will live in urban areas. To meet these needs, Whalley, speaking during the keynote session of the 2105 Cutting Edge conference in Denver, CO, said future cities will have to be reimagined and redesigned to be more efficient. A large part of that design will be in the infrastructure of those cities.At the Fourth Annual Cutting Edge Conference, Sept. 21-23, much of the discussion was around how the tunneling and underground construction industries improve cities in a number of ways, including societal, environmental and in overall efficiency. There was talk, not just about the improvements that society enjoys at the completion of such projects, but also about the challenges faced by the owner and contractor in the construction of such projects.The conference, titled Urban Tunneling, brought together some of the top minds in the industry to not only discuss the issues faced today, but also those that will shape the industry in the future.For his part, Whalley spoke about a number of projects around the world and how they have impacted society in ways beyond simply providing a better means for transportation of people or water. Notably, he spoke about the Crossrails project in London.London is a city of 8.6 million people and a history that dates back nearly 2,000 years. It is a great example of the challenges the industry faces in bringing modern efficiencies to an established city.Running more than 100 km (62 miles) with more than 42 km (26 miles) of tunnels passing through 40 stations, including 10 new stations, the project is the largest in Europe and will transform the way people move about the city."

Jan 1, 2015

By M. S. Klima, A. P. Pinkerton

Solid-bowl (decanter) centrifuges are used extensively to dewater slurries in a wide range of industries. However, the application of decanters as classification devices is not as common. In this study, the performance of a continuous, pilot-scale, solid-bowl centrifuge was evaluated when classifying an ultrafine coal slurry containing nearly 60% material less than 10 µm. The test conditions included centrifuge howl and scroll speeds, volumetric feed rate, solids concentration and pond depth. Centrifuge performance was evaluated using size selectivity curves and the corresponding performance parameters, along with product yields and solids concentrations.

Jan 1, 2002

By R. V. Ramani, R. A. Jankowski, R. Bhaskar

The spatial distribution of airborne dusts, deposition of dust in the airway, as well as the effect of airflow velocity and particle density on dust behavior in mine airways were studied in a set of experiments performed in a mine airway under controlled conditions. Considerable deposition of dust near the source was indicated. Pronounced effects due to velocity were observed in ambient dust concentration and deposition along the mine airway, both in the respirable and the total size ranges. Cross-sectional concentration measurements indicate an increase in concentration from the roof to the floor. The average cross-sectional concentration is about 75% of the concentration in the center of the airway.

Jan 1, 1987

By Li Changgen, A. Bahr

The adaptability of pneumatic flotation cells for the flotation of sulfide ore and the conditions for sulfide ore flotation in pneumatic cells were investigated. The advantages of pneumatic flotation cells over mechanical flotation cells, as well as flotation columns, for the flotation of sulfide ore were demonstrated. Test results indicated that the Cu grade and recovery for concentrates obtained when using the pneumatic flotation cell were 1 % to 2% and 4%, respectively, higher than those obtained when using the mechanical flotation machine.

Jan 1, 1993

By M. Ericsson

The extractive industries consist of five major sectors: - Mining equipment and services - Dimensional stone - Industrial minerals - Aggregates - Metal mining These industries produce some finished goods but mostly semi-finished products as they feed into other industrial sectors: Basic metals, fabricated metals, construction, chemicals, dyes and pigments, inorganic chemicals, fertilizers, rubber and plastics and non-metallic mineral products. These are the major down-stream industries in this study. Taken together with the extractive industries they form the mineral resource based cluster. The mineral resource based cluster is a substantial part of the Finnish economy: It employs 211 000 persons, 39% of the number of employees in industry. The cluster?s exports account for 20% of industry exports. Value added is 34% of total value added in industry. Investments reach 35% of total industry investments.

Jan 1, 2003

By R. Poulin, R. C. Pakalnis

Approximately 51 % of all ore production in Canadian underground metal mines is derived directly from open-stope operations. This method requires that large excavations remain open until the ore is extracted with a minimum acceptable level of dilution. A survey of underground mines in 1988 reported that a major factor in their closure was uncontrolled dilution. It has been reported that 40% of openstope operations were experiencing dilution in excess of 20%. This level of dilution has significant implications on the economic viability of a project, especially when one considers that a rate of return on a positive project is generally between 10% and 20%. This paper reports on the various definitions of dilution, on the methods of stope design that are presently used with the objective of reducing dilution and on a recently available survey technique that enables dilution to be quantified.

Jan 1, 1996

By Richard R. Klimpel

This paper reviews some of the factors involved in selecting amine flotation reagents used to remove silica from ores. A comparison is made between the chemical reagent design approaches used to identify flotation reagents that are used to recover silica- and oxygen-containing minerals and the chemical reagents used to recover sulfide minerals. This introduction gives practitioners who are involved with oxide- and carbonate-type minerals and who may not be familiar with sulfide mineral flotation some ideas of the chemical reagent design challenges that exist with froth flotation on a broader scale and why oxide type mineral flotation reagents are what they are. This is followed by several sections that discuss various classes of available amines. The closing sections emphasize that the optimal choice of an amine collector depends not only on that amine's specific chemical characteristics and costs but also on the operating conditions, especially the flotation feed particle size distribution.

Jan 1, 1999

By Sam H. Patterson

This paper is concerned primarily with the kaolin deposits extending northwestward from Macon, Ga., which is in the western part of the Irwinton district (fig. 1). These deposits are in a belt of kaolin districts extending along the inner edge of the Coastal Plain from the Aiken district, S. C., southwestward to the vicinity of Macon, a distance of 150 miles (250 km). Large kaolin deposits associated with bauxite also occur in an extension of this belt southwestward from Macon as far as the Eufaula district, Ala., a distance of about 130 miles (208 km). The belt splits away from the inner edge of the Coastal Plain in a southwesterly direction from Macon; the Eufaula district is approximately 50 miles (80 km) south of the contact of Coastal Plain sedimentary rocks with much older crystalline rocks. Structure The strata of Cretaceous and Tertiary age containing the kaolin deposits all dip gently seaward irom the landward edge of the sedimentary rocks. The dip of the Cretaceous strata is about 25 feet per mile (4.9 m per km). The dip of Tertiary strata is about 15 feet per mile (2.1 m per km). In places, the Tertiary strata overlap the older sedimentary beds and rest directly on the crystalline rocks. Faults having a few feet of displacement have been observed in several mines, but no major faulting is known in the area.

Jan 1, 1977

By J. A. Herbst, J. E. Bohrer, Y. C. Lo

A systematic approach has been developed to analyze a phosphate grinding circuit with a view toward determining promising alternatives for increasing mill capacity. This analysis was carried out and capacity increases were predicted in the context of detailed population balance models developed for the plant ball mills and classifier systems. Model development and verification was performed using data obtained in a series of batch tests and two plant test campaigns. The effects of feed rate, percent solids, ball size, and mill material filling, etc., on grinding were investigated in the laboratory and plant. Residence time distribution tests were also performed to determine the transport behavior in the mill. The population balance models were found to provide accurate predictions of full-scale grinding circuit performance. Based on the findings of this study, additional capacity in excess of 25% was predicted for these ball milling circuits by a proper combination of ball size change, mill dilution, and adopting screen classification in place of hydro-cyclones. These predictions have been confirmed by plant tests in which the recommended operating changes have been implemented. Understanding the effects of operating variables on breakage kinetics and the interplay between kinetics, transport, and classification has contributed significantly to increasing the mill capacity.

Jan 1, 1988

By M. S. J. Leary, M. J. McPherson, O&apos

This paper introduces a computer simulation that extends the use of microcomputer systems for mine ventilation planning. The program was developed as part of an ongoing study to produce a simulation model that would determine the optimum duties of a main fan and a booster fan without requiring the trial-and-error runs that are necessary with currently available programs. To use the new program, the user specifies the location of one main fan and one booster fan, and the minimum required airflows in any number of working places. The computer determines the fan duties that will maintain the required airflows at the lowest operating costs without causing undesired recirculation. The methodology of the program and an example showing how it can be applied are presented.

Jan 1, 1990

By Robert C. Freas

Over the past twenty years people throughout the world, but particularly in the United States, have been taking an increasing interest in the environment, sources and causes of pollution, and pollution abatement. Air quality in the United States has been and continues to be an area of primary emphasis. In 1970, the US Congress passed the Clean Air Act and subsequently revised and strengthened it in 1977 with the issuance of the New Source Performance Standards. The Act has been further strengthened with the passage of the 1990 Amendments. By far the largest single source of sulfur dioxide (SO,) pollutants are coal fued electric generating power stations. Hence, a substantial portion of the flue gas desulfurization (FGD) research and equipment installation has been geared to the utility industry. Several competing FGD technologies were touted during the period 1970 to 1990 with varying degrees of success. Subsequently, the more successful technologies have been accepted, revised, and improved to the point that by 1991 third and fourth generation technology is available. A second area of emphasis for FGD has been coal fired industrial boilers. While individually they are much smaller than any electric utility generating station, they do represent a significant source of sulfur pollution. However, due to the size of industrial boilers and their location within industrial and educational complexes, the wet scrubber technology being employed by the utilities is not appropriate for these applications. Hence, fluidized bed combustion (FBC) technology has been developed for the industrial boilers. Since the installation of the first full scale test unit at Georgetown University, several equipment vendors have come forward with an increasing array of more sophisticated FBC units. Currently, FBC technology has matured to the point that the Tennessee Valley Authority (TVA), in cooperation with the Electric Power Research Institute (EPRI), has installed an FBC system on a 250 MW test unit at the Shawnee Power Station in Kentucky.

Jan 1, 1994

By H. D. Freeman

The Pacific Northwest Laboratory (PNL) is developing cover technology for uranium mill tailings that will inhibit the diffusion of radon to the atmosphere. As part of this cover program, an improved radon flux measurement system has been developed. The radon measurement system is a recirculating, pressure-balanced, flow-through system that uses activated carbon at ambient temperatures to collect the radon. With the system, an area of 0.93 m2 is sampled for periods ranging from 1 to 12 h. The activated carbon is removed from the radon trap and the collected radon is determined by counting the 214Bi daughter product. Development of the system included studies to determine the efficiency of activated carbon, relative calibration measurements and field measurements made during 1980 at the inactive tailings pile in Grand Junction, Colorado. Results of these studies are presented.

Jan 1, 1981

By Allan D. Fernie

Many long conveyors, 2 - 20 km plus, have been installed over the past 10 years. Conveyor belt life, depending on the conveyor length and material handled, will generally range from 10 - 15 years. To replace long conveyors splicing one or two rolls into a conveyor run on an intermittent basis can be prolonged in an operating system involving considerable downtime and scheduling problems. This paper presents some of the methods used to- date and highlights forward planning for such an event. Special belt handling equipment required and the execution of a belt change operation are described in detail. Wright Engineers Limited have worked in collaboration with Canada Conveyor to design and implement the methods described herein.

Jan 1, 1993

By Jay Hilary Kelley

A ventilation system is described using dual aircourses: one zone occupied by working personnel, the other at the active working face. The two zones are separated by a partition or Shroud. The occupied zone to the rear of the face zone is ventilated adequately but with considerably less air because little gas, dust, or fumes are present. The face excavating zone is sealed and maintained at slightly more negative pressure preventing dust and gas generating from within to escape. Explosive mixtures within the face zone is rendered non-explosive by the introduction of inert gas therein. Each zone is vented separately to the outside of the mine. Because less total quantity of air is required for human breathing, etc, the total ventilation system can be drastically reduced in tan capacity, development entries, and air shafts, -- a great savings in costs.

Jan 1, 1991

By J. Twining, V. Nguyen, J. Perera

A computer code for ecological risk assessment (ERA), AQUARISK, has been developed and applied to evaluate the likelihood of biotic detriment due to exposure to acid rock drainage (ARD) from the Burkunga mine site in Australia Stream water quality monitoring data were used for the assessment and were compared with a) national water quality guidelines, b) literature derived ecotoxicology data and c) biological monitoring data. With bioavailability calculations, the code predicted that, for metals exceeding the guidelines, 44% of macroinvertebrate species above the mine and 100% below the mine would be adversely affected by the metals in the stream. This compares reasonably and conservatively with biological monitoring that showed observed reductions of 41% and 85% of species respectively at each site. Using literature data for macroinvertebrates to predict impact produced similar estimates to using data for all taxa. Use of speciation modeling also lessened the degree of reduction in the median water metal concentrations required to achieve acceptable impact (measured either by exceedence of criteria or by species likely to be affected) by a factor of 75%. This result implies significant economic and management benefits in relation to remedial engineering or water treatment options for sites.

Jan 1, 2000

By W. S. Sadik

This paper presents the ventilation design for an underground testing facility in a salt medium. The underground workings consist of two-12 ft. (3.66 m) diameter watertight shafts and approximately 6000 ft. (1830 m) plus of drifting. These facilities are designed for the purpose of providing access for an in-situ testing of a salt horizon in which a variety of hazardous and non-hazardous materials could be temporarily stored or permanently deposited. The ventilation system includes a design basis for gassy mine conditions and provides for the option of bulk air cooling and heating.

Jan 1, 1988