Search Documents

Gaby Copper Mining?s Gabriela Mistral property is located in the Antofagasta region of northern Chile, at an altitude of 2,660 m (8,727 ft) above sea level. The reserve contains an estimated 562 Mt (620 million st) of oxide ore with an average grade of 0.41 percent total copper. The mine went into production in 2008. Gaby Copper faced the problem of having no reliable way to measure the solids level. This is a challenge that exists throughout the mining industry, where dust in the air and accumulation of solids on a sensor make accurate measurements difficult in areas such as transfer chutes, the rock box underneath crushers, silos and anywhere else that information is needed on the level of solids. The next-generation technology in the Sitrans LR560 radar from Siemens addresses this challenge. With a frequency of 78 GHz ? higher than previous generations of radar ? it provides a more robust signal for measuring in areas where there are high levels of dust accumulation. The Sitrans LR560 provides a signal beam angle of four degrees, significantly narrower than any other product on the market can offer.

Jan 1, 2014

By SME SME

List of 43rd ICGCM 2024 ORGANIZING COMMITTEE

Jun 25, 2024

By Jakub Nalaskowski, Vamsi K. Paruchuri, Marcin Niewiadomski, Jan D. Miller

Spherical oxide particles can be used as mineral fillers, paint pigments, polishing materials and catalysts. They can be prepared using various techniques involving precipitation and spray drying. Melting of particles in a high-temperature flame is a simple technique which produces particles with a high degree of sphericity and high smoothness from non-spherical feed material. In current research the preparation of alumina particles by melting the feed material in a hydrogen- oxygen flame is described. The spherical particles obtained were characterized using scanning electron microscopy, atomic force microscopy, energy dispersive spectroscopy, X-ray difiaction, Fourier transform infrared spectroscopy and electrokinetic measurements. The particles pre- pared exhibit a high degree of sphericity and a low level of roughness. The chemical composition of the material after preparation is unchanged, however the crystallographic structure is different. It is suggested that alumina changes from pure a-alumina to a mixture of different transitional forms. Changes in the electrokinetic behavior were also observed for alumina which can be attributed to the strong dehydration of the oxide surface and/or change in the crystallographic structure. Also, the possible accommodation of trace amount of impurities in the surface zone during melting cannot be ignored.

Jan 1, 2003

By V. Srajer

This paper deals with the problem of efficiently selecting the most appropriate loading and hauling equipment for surface mines. Problems and factors that affect productivity and operating cost are identified. During the course of collecting the information for this study, mining companies and equipment manufacturers were interviewed to define their selection practices. The majority of mining companies prepare general specifications and ask the suppliers to mate those specifications to their product line. The mining company then evaluates various proposals on the basis of the best available deal. The following 'mines from western Canada provided information for this study: Coal Mountain, Line Creek, Quintette, Westar's Harmer mine from the Province of British Columbia, and Coal Valley, Gregg River, Highvale, Luscar from the Province of Alberta.

Jan 1, 1989

By T. M. Barton, M. Gauna, A. A. Campoli

Coal mine bumps, the violent failures of overstressed coal, present a safety hazard to miners when longwall mining is conducted in deep, bump-prone coal mines. Two different longwall gate entry systems were evaluated in a southern Appalachian coal mine located in the Pocahontas No. 3 coalbed under approximately 610 m (2000 ft) of overburden that included a massive sandstone member. Both gate entry systems employed a center abutment pillar flanked by yield pillars. The original design used a 24.4-m (80 ft) square abutment pillar, while the new design employed a 36.6-m x 54.9-m (120 ft x 180 ft) abutment pillar. Rock mechanics instrumentation data analysis and in-mine observations indicated that this increase in abutment pillar size significantly decreased bump potential. The new design in worst-case conditions increased effective bearing area 62%, with only a 9% increase in gate entry system width, and eliminated face bumps that were experienced with the original gate entry design.

Jan 1, 1993

By H. Huang, J. C. Wu, C. H. Xie, Y. Q. Xue, Z. H. Zhang

Two- and three-dimensional groundwater flow models for dewatering in an opencast mine are presented. The models focus on solving special problems using numerical simulations of the opencast mine. These special problems include the drying up of the aquifer, the movement of the model boundary and the prediction of the residual head. These models are used to describe the decline of groumdwater levels in the Yuanbaoshan Opencast Coal Mine and its neighboring area during the drainage period. The simulated values agree very well with the field data. There have been several successful examples of numerical simulation for predicting the mine dewatering rate in an opencast mine. However, The hydrogeological conditions for the Yuanbaoshan Opencast Coal Mine are rather complex, and the total average flow rate is very high at 4.676 x 105 m3/d (1.65 x 107 cu ft/day). In this paper, a two-dimensional groundwater flow model in a large area is developed to solve the problems mentioned above by simulating regional drawdowns of the groundwater level during the drainage period, and a three-dimensional flow model is developed to simulate the residual head near the open-pit bench.

Jan 1, 1998

By W. F. Hahnert, P. A. S. Ralston

In off-line training of a rule-based controller, the significant measure of successful training is the quality of control provided by the generated rule set. In an adaptive or on-line control environment, performance is also measured by the ability to accurately maintain a satisfactory rule set, but within constraints on speed and/or resource availability. Very small population genetic algorithms, or microGAs, have been proposed as a means of capitalizing on the hill climbing characteristics of faster local optimization techniques while requiring less memory and retaining much of the robustness of traditional, larger population genetic search. A traditional genetic algorithm and a similar microGA are developed and applied to two control problems. The performance of these algorithms is analyzed with respect to (1) the quality of the rules learned, (2) the rate at which learning occurs, and (3) the memory resources required during learning.

Jan 1, 1993

By T. Vandergrift, J. Sturgill, W. Gerhard, J. Carrick

As surface minable coal is depleted, many operators look to high-wall mining to extend reserve life. Recent advances in highwall mining equipment have greatly improved productivity, clean coal recovery, and attainable penetration beneath the highwall. Somewhat lagging have been systematic design approaches for ensuring web pillar and overall highwall stability. This paper presents an overview of the design, planning, and field performance of a multiple-seam highwall mining application in southwest Wyoming. The safety and efficiency obtained to date is attributable to the careful geotechnical and operational planning described herein. Field confirmation of performance and suggestions for improvement are also discussed.

Jan 1, 2004

By J. C. Stankus, S. S. Peng

Many coal seams are associated with soft floor strata. During mine development, if coal pillars are not properly designed, floor heave occurs and causes interruption of coal production. In the severe cases, the section or mine is abandoned. One method for controlling floor heave is floor bolting. This paper describes the demonstration of flour bolting methods in a West Virginia, info coal mine. Three methods were used: vertical full resin bolting, floor truss bolting and floor truss bolting pins a floor slot at the center of the entry. The design of each method and the experimental results are discussed.

Jan 1, 1995

By DeVerle P. Harris

The structure of an exploration model reflects a number of design considerations, one of which is the question or issue-to be investigated by the model. Thus, a model designed to evaluate the magnitude of risk and its economic implication to optimal decision making at each decision juncture of a multistage exploration architecture differs considerably from one designed to evaluate, say, the long run average cost of discovery, in which the architecture of exploration is suppressed and risk is simply an element of average cost. The perspective of the model examined in this paper is that exploration is investment in (purchase of) information and that the next stage of an exploration program is undertaken only when the expected value of information to be acquired in that stage exceeds its cost. The degree to which this perspective is honored influences considerably model design. Consider two design objectives:

Jan 1, 1989

By C. E. Jordan, B. J. Scheiner

The Bureau of Mines has developed a continuous ultrasonic flotation cell for the recovery of Florida phosphate ore. Within a small mixing chamber near the bottom of the flotation cell, an ultrasonic probe agitates an injected mixture of air, water, and phosphate ore and breaks the air into fine bubbles. Phosphate particles are preferentially attached to these fine bubbles and floated in the main chamber of the flotation cell. Over 94 pct of the phosphate was recovered, resulting in a 30 pct P205 concentrate. The ultrasonic energy consumption was less than 7 kW.h/mt of phosphate ore.

Jan 1, 1989

Caterpillar and Fortescue Metals Group have moved forward with the delivery, installation and support of a complete Cat MineStar System at Fortescue?s Solomon iron ore mine in the Pilbara region of Western Australia. The complete technology suite was implemented for the first phase of Solomon, the 20 Mt/a (22 million stpy) Firetail manned mine, in October 2012. As part of an autonomous mining solution for phase two, the 40-Mt/a (44-million stpy) Kings Mine, eight Command for hauling Cat 793F CMD trucks were commissioned and commenced operations in the second quarter of 2013. The mine plan calls for a progressive ramp up to 45 autonomous trucks during the next several years. In addition, other Cat MineStar System capability sets, Fleet, Terrain, Detect and Health, are being used across the mobile equipment fleet, including support equipment and light vehicles. Working closely with Fortescue and its mining contractor, Leighton Contractors, Caterpillar and the Cat dealer in Western Australia, WesTrac, are providing a full solution for managing, operating and supporting Cat MineStar System and Command for hauling. The greenfield Solomon Mine has brought together the skilled team from Caterpillar, Fortescue, Leighton Contractors and WesTrac to deliver an efficient, cost effective autonomous mining solution.

Nov 1, 2013

By M. C. Roberts

To assess the future markets for a mineral from a producing district, the following three aspects must be considered: the future growth of the markets, the competitiveness of the district in terms of production costs and reserve adequacy, and the competition from alternative sources of supply. This paper focuses on the first issue by developing a method for predicting the demand for phosphate from trends in the major market for phosphate products, the fertilizer and agricultural market. The paper shows how broad changes in this end-use market for phosphate has evolved over time. These trends are then projected into the future to make an assessment of future phosphate requirements.

Jan 1, 2000

By Walter C. Labys

There has been considerable growth in public enterprise institutions involved in mineral commodity markets. These institutions typically consist of trading organizations (STO1s), regulatory agencies, and mixed agencies. The particular character of these institutions varies according to whether they reside in developing countries, in Eastern Europe (COMECON Countries), in industrialized countries, or in the form of international agencies. The purpose of this paper is to explain recent attempts to assess the growth of public enterprises as well as their impacts on mineral markets and trade. Some earlier analyses of market impact made by the author have been up- dated for four major mineral markets: copper, tin, bauxite and iron ore. Conclusions are drawn regarding the dynamics of market structure changes and their impacts.

Jan 1, 1986

By Donald J. McKee

The product sizing and tonnage from a grinding circuit are the end result of a series of linked size reduction stages which always involve: fragmentation in mining; degradation in transport of ore; crushing and finally grinding. A case study is presented which illustrates the substantial effect on autogenous mill throughput of different mining practice. It is shown that it is possible to model each of the size reduction steps of fragmentation, degradation, crushing and grinding. The way in which this predictive capability is used is dependent on the operating constraints of each mine-mill combination.

Jan 1, 1998

By Terrence Chatwin, Michael Sweeney, Steve Accardo

Sutter Gold Venture excavated an exploration decline into a mineralized zone in the Sutter Creek gold mining district. Delays in obtaining the conditional-use permit resulted in 7 to 10 million gallons of water accumulation in the decline containing elevated dissolved arsenic. Sutter received a permit to land apply the water after reducing the arsenic concentration to 0.05 mg/L. Initially the water was treated by co- precipitation arsenic with ferric hydroxide. Operational difficulties of this treatment system resulted in Sutter pursuing alternative treatment methods. The activated alumina adsorpting was selected due to its flexibility and ease of operation. Operating and maintenance data and costs will be presented.

Jan 1, 1995

By W. C. Patrick

The Spent Fuel Test-Climax (SFT-C) was con- ducted to evaluate the feasibility of retrievable deep geologic storage of commercially generated spent nuclear-reactor fuel assemblies. One of the primary aspects of the test was to measure the thermomechanical response of the rock mass to the extensive heating of a large volume of rock. Instrumentation was emplaced to measure stress changes, relative motion of the rock mass, and tunnel closures during three year of heating from thermally decaying heat sources, followed by a six month cooldown period. The calculations reported here were performed using the best available input parameters, thermal and mechanical properties, and power levels which were directly measured or inferred from measurements made during the test. This report documents the results of these calculations and compares the results with selected measurements made during heating and cooling of the SFT-C.

Jan 1, 1986

By Steve Kral

The Northwest Mining Association (NWMA) has been an advocate for the U.S. mining industry since 1895. For several decades, the organization has represented mining members located mostly in the Northwest and some southwestern Canadian provinces. Today, though, the NWMA?s membership is located in 42 states and seven provinces and has become a national voice for the mining industry. So, during the association?s 119th and final meeting as the NWMA, a name change was announced. The organization is now called the American Exploration and Mining Association (AEMA). But that?s not all that has changed, according to the association. The new name reflects more closely the diversity and location of the AEMA?s membership. It will still be an advocate for the mining industry, dealing with land, environmental and community issues on state and federal levels. The conference, held in December 2013 in Reno, NV, attracted about 2,500 attendees. And the accompanying exhibit included 230 equipment and service suppliers in 246 booths. Technical programming ran the gamut of mining industry issues and technologies, including surface and underground mining; high technology systems and automation in mining, metallurgy and exploration; along with social issues, finance and safety. The following is a sample of some of the sessions.

Mar 1, 2014

By Isabel Barton

This article describes and analyzes the history of research into the origins of the uranium-vanadium(-radium) deposits of the Paradox Basin. For several decades after their discovery in 1881, research was desultory and almost entirely descriptive, fluctuating with demand for vanadium and radium. Systematic geologic descriptions, accumulated between 1910 and 1950, supported rapid progress during a government-backed surge of research in the 1950s, when uranium was the chief commodity of interest. Most of the major theoretical innovations date from this decade, including the use of concepts from solution chemistry to identify the conditions and constrain the processes of deposit formation and alteration. Research from this time was highly influential in geology at large, providing the model for sandstone-hosted uranium deposits worldwide and numerous new minerals and mineral structures. After about 1960, mine production remained high but research dwindled, and most new advances were to the details of the hydrothermal model of ore formation rather than its core concepts. By the end of the 1960s, the deposits were understood to have formed at the mixing interface of an oxidized, metal-bearing water with a reducing fluid of debated origin. Research was desultory over the ensuing decades; the source of the metals and the nature of the chemicals constituting the trap were not clearly established. They remain questions today, as do factors like the relationship between ore mineralization and the geologic history of the basin. (More in the full paper.)

Jan 1, 2025

By R. L. Grayson, S. Yuan

A goal-programming-based, worker-scheduling model has been incorporated in the Mine Management Support System (MMSS) for assigning workers to prioritized jobs on a shift basis. In the model, the accomplishment of each regular and non-regular job is a goal, and the objective is minimization of the deviations from the goals. A number of coefficients are employed as premultipliers of the decision variables to address practical considerations associated with the utilization of workers and the requirements of jobs. This model is applied to a 41-worker problem.

Jan 1, 1992