Search Documents

By A. A. Peshkov, N. A. Matsko, K. N. Trubetskoy

It is possible to divide the general objectives of a company into two components: maximum expected profits and viability over time. These components are designed to maximize the companies value over time. The evaluation of a project includes both a discounted cash flow (DCF) analysis and a risk analysis. The DCF analysis determines whether the project should be accepted or rejected, and the risk analysis helps to forecast possible deviations from the original estimates. However, the results of both methods do not allow for a quantitative comparison between the main objectives of the venture, and they do not resolve the issue of whether it is advisable to sacrifice immediate profits for future profits. This paper attempts to resolve this issue. The present research was carried out on mining projects with different waste-extraction schedules. Calculations were made using the US Bureau of Mines' usage-of-costs model. Russian experience in open-pit mining is reflected in this paper.

Jan 1, 1996

By M. E. Smith

Chile is the world's largest copper producer and as such sets the standard of practice in copper SX/EW design. The authors summarize the liner systems used at many of Chile's major copper producers both operating and planned. The evolution in the state of the art is also discussed, considering both economic factors and Chile's burgeoning environmentalism.

Jan 1, 1994

By Robert J. Timko, Lincoln Derick

This work is a follow-up to previous research that attempted to predict the location of spontaneous heating episodes in underground coal mine pillars. The objective of the original work was to see if the data obtained by commonly used detection methods could accurately predict spontaneous combustion episodes in coal pillars. Data accumulation during the study was enhanced when a spontaneously generated fire occurred within one of the pillars being examined. The fire provided researchers with realistic data that could be used to determine if fire prediction was possible. Results from the initial study found that the atmospheric status equations that were used provided little advance notice that combustion would occur where it did. This study reevaluated the accumulated data by applying it to recently developed equations and compared these results with previously obtained information to determine if a combination of these techniques could more effectively predict impending combustion.

Jan 1, 1995

By F. F. Peng, S. S. Peng, V. Z. Sun

A detailed study of ponding phenomenon relative to surface subsidence due to longwall mining was conducted for various surface stream conditions. Based on field monitoring, the stream-ponding process and three forms of stream water are described. Also discussed are the criteria of stream ponding and the influences on the ponding process by two key factors: the angle of stream flow and the change in the stream-bed gradient. A numerical (mathematical) model, which combines trend surface technique that describe the topographical features in the vicinity of a stream and the modified influence function, which represents the profile of the surface subsidence trough (or basin), is constructed to predict the formation characteristics of stream ponding in terms of location, boundary and accumulated water volume of migratory and stationary ponds produced by the stream-ponding process. Three cases are analyzed using the model to predict the interaction of the underground operations and the environmental impact due to stream ponding. The feasibility of various mitigative measures are assessed.

Jan 1, 1997

By W. K. Tolley, D. G. Kotlyar

Silver is an economically important component of many complex, massive sulfide ores. The beneficiation of this type of ore is now almost entirely accomplished by flotation. Silver recovery is often low, and little is known about the flotation behavior of the silver-bearing minerals. Floatability studies were conducted using silver-bearing tetrahedrite and lead-zinc ore. The effects of xanthate-collector concentration, conditioning time, potentiostatic control of the mineral potential and control of the pH on mineral floatability were evaluated. The floatability of the silver-bearing minerals was shown to depend on collector concentration and mineral potential. The effect of controlling the mineral potential during the flotation process is discussed.

Jan 1, 1996

By Z. D. Hora, W. N. Hamilton

Evaporite units of the Western Canadian Sedimentary Basin are known to host native sulfur. In British Columbia, a large number of oil and gas exploration drilling holes reported intersections with native sulfur. The most important ones include 6 meters (20 feet) and 27 meters (90 feet) of native sulfur among 23 occurrences in Devonian Muskeg evaporite or adjacent Slave Point reef facies carbonates. A small Frasch sulfur deposit is known from Devonian Wabamun Group sediments near Camrose in South Central Alberta. Occurrences of native sulfur are common also in association with presently mined gypsum of Devonian Burnais Formation in southeastern British Columbia. Triassic sediments with evaporite members in British Columbia are also known to contain native sulfur showings. A widespread presence of anhydrite in many sedimentary units of Alberta and British Columbia together with oil and gas fields in the same areas and associated native sulfur occurrences point to a possibility for Frasch sulfur deposits in this part of western Canada.

Jan 1, 1992

By J. G. Groppo, D. J. Sung, B. K. Parekh

Hyperbaric filtration for the dewatering of fine coal cleaned by froth flotation was evaluated on a laboratory scale. A laboratory pressure filtration procedure designed to obtain a uniform cake structure from dilute slurries containing a significant amount of coarse material is described. Baseline tests were conducted to determine the optimum operating conditions for the eventual application of the process to a continuous pilot-scale hyperbaric filter. Investigated were filter operating parameters such as driving force, time, cake thickness, percent solids, viscosity and pH.

Jan 1, 1996

By M. Ghiani, R. Ciccu

After a short review of the basic concepts underlying the application of selective flotation and electrostatic separation to the beneficiation of phosphate ores, the paper deals with the results obtained with these two technologies for a number of run-of-mine ores of different origin and distinct mineropetrographic features. Problems are discussed in the light of the minero-petrographic characteristics of the ores.

Jan 1, 1993

By M. Kumral

The in-situ mineral characteristics of a deposit are simulated by sequential co-simulation and averaging the simulated characteristics within specified block volumes creates a three-dimensional block model. This model is then submitted to optimal open pit and production scheduling algorithms. As the market values of industrial minerals depend on the satisfaction of predetermined blending criteria rather than metal content, a Linear Programming (LP) scheme has been used to identify all blocks that can be included in the blend without violating the grade requirements. The Lerchs-Grosmann algorithm using the blocks identified by the LP program determines optimal pit limits. All blocks that lie outside the optimal pit are removed from the system and the blocks within the optimal pit are submitted to the production-scheduling algorithm. Production scheduling optimisation is done in two stages: Lagrangean parameterisation, resulting in an initial sub-optimal solution, and multi-objective simulated annealing (MOSA) improving the sub-optimal schedule further.

Jan 1, 2002

By J. L. Kohler

Control circuit failures contribute significantly to continuous miner downtime. The time required to put the machine back into production is a function of the time required to diagnose the problem, obtain parts, and make the repair; of these, the diagnostic time is often the largest. A microprocessor-based system with the ability to diagnose all of the common control circuit failures was designed, installed on a continuous miner, and tested. This paper summarizes the development of the diagnostic system, and provides examples of the system's diagnostic capabilities. Implementation issues and the hardware used for the prototype are briefly described. Finally, comments on the system's performance are presented.

Jan 1, 1993

By X. Wen, D. Tao, B. Li

A high effective method using a hammer mill, a column pneumatic separator and an electrostatic separator was studied for recycling copper from waste printed circuit board. The factors influencing the copper liberation degree and following separations were discussed. Two different physical separating methods were compared and discussed. Experiment results show that a well-controlled impact action can produce a satisfactory degree of copper liberation at a relatively coarse particle size. Around 90% copper recovery from printed circuit board for coarse particle size can be achieved by using a combination of electrostatic separation and pneumatic separation.

Jan 1, 2003

By R. V. Ramani, S. Skankar

Available literature on the effect of re-entrainment on overall airborne dust concentration in mine airways or the fundamental mechanisms of coal dust re-entrainment in mine atmosphere is scant (Shankar and Ramani, 1991). Therefore, as part of the Respirable Dust Center's ongoing research, the following three-part study was undertaken: •a study of the re-entrainment phenomena of anthracite and bituminous coal dust particles in a wind tunnel under the influence of varying air velocities; •a study of the same in the Lake Lynn Laboratory Mine of the USBM with both air flow and walking by personnel causing re-entrainment; and •the mathematical modeling and computer simulation of the re-entrainment phenomenon. In this paper, results from the re-entrainment studies in the wind tunnel and the Lake Lynn Laboratory mine are presented. Comparing the results from the two studies, it was observed that increasing the air velocity increased the rate of re-entrainment (Shankar and Ramani, 1994a) and the rate of re-entrainment decreased with the time of exposure of the source dust to the flowing air. In addition, when the source dust was composed of particles of different sizes, the airborne dust concentrations due to re-entrainment were higher than when the source dust was composed of particles of the same size. The contribution of airborne dust concentration due to airflow was negligible compared to the contribution due to walking.

Jan 1, 1996

By G. R. Rao, K. A. Natarajan, P. Devasia

The role of growth conditions and adhesion of Thiobacillus ferrooxidans on the leaching of chalcopyrite was investigated. Thiobacillus ferrooxidans grown on sulfur, thiosulfate and ferrous ion substrates was used in this comparative study. Growth on sulfur, a solid substrate, requires bacterial adhesion unlike that required in the presence of soluble thiosulfate and ferrous ion in a mineral-salts medium. Solid substrate-grown cells showed higher rates of leaching than those grown in liquid media. An initial lag period noticed during leaching by solution-grown cells was absent when solid substrate-grown cells were used. Such a behavior is attributed to the presence of an inducible proteinaceous cell-surface appendage on the sulfur-grown cells. This appendage aids in bacterial adhesion onto the mineral surfaces. Such an appendage is absent in solution-grown cells, as substantiated by electrophoretic measurements. The importance of bacterial adhesion and the direct mechanism in leaching by Thiobacillus ferrooxidans are demonstrated.

Jan 1, 1997

By John Greenhalgh, Benoit De Rivaz

"1.INTRODUCTIONThis paper is based on the Lee Tunnel project, which is part of the Thames Water’s Tideway Project.The client Thames Water has employed a Joint Venture of Morgan Sindall/Vinci Grand Projets and Bachy Soletanche to undertake the design and construction of the project under the management of CH2M Hill at a value in excess of £635 million ($990 million). The 3 main elements of the tunnel project are the permanent lining to the shafts, the precast segmental lining, and the secondary tunnel lining. All 3 are reinforced with different types of Dramix steel wire fibers and each element will be described in this paper. This paper will explain the basic structural design of FRC (Fiber reinforced concrete) based on the post cracking residual strength and will describe all the steps of this project, the testing program realized to support innovative design and the main technical learning point. 2.BASIC CONCEPT OF STRUCTURAL DESIGN OF FRCStructural design of FRC elements is based on the post-cracking residual strength provided by fiberreinforcement. Other cases, like early age crack-control or fire resistance, are considered non-structural use of FRC. For structural use, a minimum mechanical performance of FRC must be guaranteed. Fibers can be used to improve the behavior at SLS (Service Limit State) since they can reduce crack spacing and crack width, thereby improving durability and they can be used to improve the behavior at ULS (Ultimate Limit State) where they can partially or totally substitute conventional reinforcement in most conditions. In the design process, the definition of the performance expected from the material is a key factor and the mix-design of the material has to be optimized for the required structural performance.2.1 Testing Method In order to ascertain the structural requirements requested for the FRC segments, preliminary testing on samples will be required and the effectiveness of the proposed solution will also be assured by the testing of full scale specimens. Structural design of FRC elements is based on the post-cracking residual strength provided by fiber reinforcement. For structural use, a minimum mechanical performance of FRC must be guaranteed. Nominal values of the material properties can be determined by performing a 3-point bending test on a notched beam according to EN14651 (figure 1) or by performing the ASTM C1609 beam test:"

Jan 1, 2016

By R. D. H. Bedd

GEOLOGICAL NOTES The area under discussion is situated approximately 150 m north of Loraine No. 3 shaft at ± 1500 m below surface. The block being mined extends from about halfway between 50 and 52 levels to just below 48 level (see Fig. 1). The EB reefs form the lower portion of the EB zone of the Elsburg series and in the 81 line area the various conglomerate bands show the best development. Up to 18 separate reef bands are developed and the distance from the bottom conglomerate band to the top is ± 26 m. The thickness of the quartzite which forms the middling between the various reef bands varies from 0.1 to 2 m. The strike is roughly north-¬south. The reef bands are payable individually. However, owing to the steepness of the reefs and their close prox¬imity, conventional mining would prove very difficult. The nonpayable reef bands all carry varying amounts of gold and the whole area is a massive payable reef body approximately 26 m wide and 60 m high at 300 to 400 m on strike. The major structure of the area consists of a north¬-south trending syncline. The western flank of the syncline has a steep easterly dip, in places approaching the vertical. This flank cuts out against the overlying rocks of the EA zone. The latter forms a noncon¬formity with the underlying EB zone. The eastern flank of the syncline dips to the west at an average dip of 0.17 rad (10°). The 0.1 rad (6°) north-plunging syncline was sub¬jected to severe faulting. The most important are the Nos. 4 and 10 faults, both of which have a roughly north-south strike. The No. 4 fault dips to the west at an angle of 1.04 rad (60°) with a downthrow of approximately 150 m to the west. The dip of the No. 10 fault is 0.69 to 0.81 rad (40° to 50°) west, with the western block having moved 150 m updip relative to the eastern block. The EB reefs are being mined by the sublevel stoping method down from the sub-outcrop position to the cutoff against the No. 4 fault. On the downthrow side of the No. 10 fault, that is just above the 54 level, two reef bands are payable and will be mined conven¬tionally. ROCK MECHANICS From the section in Fig. 1, it can be seen that the area under consideration is surrounded by stoped-out areas. This will naturally change the stress distribution extensively. The only way to calculate the stress field for such a geometry is to use the finite element method. It was established that this method worked for the present geometry and so the method was applied to predict the stress behavior of the final geometry. From the results, it appeared that the effect of the old stopes was to destress the area. There are, however, some areas-such as the 50 and 48 north footwall haulages-which will require continuous attention. In these two footwall haulages, deterioration can take place due to tensile stress which

Jan 1, 1982

By K. I. Cunningham, C. S. Spirakis

Two types of native sulfur deposits have been found in Lechuguilla Cave: thin late-stage crusts and massive early- formed deposits. Most, if not all, of the crusts appear to have formed by remobilization of native sulfur contained within gypsum and sulfur masses. The process is occurring today and is slowly converting the sulfur to gypsum. The absence of primary gypsum or reductants in the cave indicates that the early-formed massive sulfur deposits did not form by in-place reduction of sulfate, which is the process that formed the commercial sulfur deposits in the Delaware basin. Instead, it appears that H2S dissolved in basinal brines was oxidized by oxygen in near-surface ground waters in the cave. Fluid- inclusion data, which suggest the presence of both fresh water and saline water as the sulfur formed, support this interpretation. Although individual sulfur deposits in Lechuguilla Cave are no more than several tens of metric tons, the abundance of secondary gypsum (as much as 10 meters thick) indicates that native sulfur may once have been much more extensive.

Jan 1, 1992

By Donald C. Moore

Introduction Asamera Minerals (US) Inc. and its joint venture partner, Breakwater Resources Ltd., discovered ore grade gold mineralization on their 20 km2 (5000 acre) Wenatchee, WA land position in February 1983. Due to the high grade nature of the discovery ore and the known reserves of ore in the "B Reef' and "B West" zones previously outlined by other companies, a decision was made to construct a mine/mill operation near the known ore occurrences. Further drilling in the discovery area quickly expanded known gold occurrences to more than 3.6 Mt (4 million st) with tentative in-place ore grade of 7 g/t (0.25 oz per st) and minor silver values. Based on existing knowledge of the ore body and the rapidly increasing ore reserve, a decision to build a 1.8-kt/d (2000-stpd) mine and mill complex was made in the second quarter of 1983. A schedule was devised to begin immediate mine development, shaft sinking, environmental and land use permitting, and mill and tailings dam construction (Fig. 1). Meeting the scheduled startup date, April 1, 1985, required a fast track schedule in all areas. To this end, Asamera purchased the Oracle Ridge Partners concentrator. This was an assemblage of new equipment designed for use as a copper concentrator in southern Arizona. The purchase contained all of the major mineral dressing equipment - crushers, screens, rod and ball mills, etc. and an engineering package. It did not include most of the other required items, such as buildings, conveyors, pipelines, tanks, and pumps. At the same time, core samples were sent to two independent process development laboratories for initial flowsheet development. Due to the refractory nature of the carbonaceous ore, cyanide leaching was not feasible. Flotation was selected as the concentration process. Further testing showed that autoclaving of the flotation concentrate followed by cyanidation would result in overall recovery of about 85% gold. A mine manager was hired to begin assembling an operations staff, hire an environmental consulting firm, and begin mine development. Environmental and land use concerns were major obstacles due to the mine's close proximity to a city of 20,000 people. These concerns had to be rapidly defined so as to mitigate any adverse impacts from and mining processing operations. Baseline data dealing with weather, air and water quality, and sound were measured before start of mine construction. Concentrator and flowsheet development remained static until October 1983 while definition drilling and mine development proceeded. In late October, a process engineer was hired to coordinate development of a process flowsheet, purchase the remainder of the concentrator equipment, prepare a concentrator construction contract, finalize concentrator detail engineering, and combine environmental and process requirements with a tailings dam design. Process development There were only 17 months remaining to mill start up from the hiring date of the process engineer. Therefore, the process flowsheet had to be finalized rapidly. To accomplish this, samples of drill core from the highest grade (and therefore potentially the most commercial) ore zones were sent to an outside metallurgical laboratory to confirm beneficiation tests on the flotation process. Test results again showed that flotation would provide about an 86% gold recovery. Therefore, all further testing was concentrated on flotation and autoclave/cyanidation of flotation concentrates. Focusing on a well known process such as flotation was important in accomplishing the rapid design and construction of the concentrator. If, during these next phases, we were continually changing design concepts, layout, and process flow, the mill startup would have been delayed many months. Once a process flowsheet is selected the process engineer must obtain the process criteria needed to design the beneficiation system. For example, it was known in early December that the Oracle Ridge rod and ball mills were too small to grind 1.8 kt/d (2000 stpd) of Wenatchee ore. A decision had to be made to purchase a large, used ball mill and convert the Oracle Ridge ball mill to a rod mill. The process engineer must be cognizant of the process criteria needed to size and select equipment. If not, the process engineer must use the professional services of the equipment manufacturing companies to review the requirements that the equipment is asked to perform. For the Wenatchee system, this resulted in the adaptation of a ball mill to a rod mill with a weight limit of grinding rods to protect the mill bearings and drive trains. When a decision is required, the process engineer has to present the facts and options in a manner that allows a rapid decision. This information must include costs, equipment availability, and effect on the construction schedule. At the Cannon mine, there were process development details that resulted in decisions similar to the ball mill purchase. These included an increased flotation residence time from eight to 25 minutes, an increased thickener area requirement, a high pressure tailings pumping system, and area constraints in plant layout. All of these decisions had to be timely and required assistance from manufacturers' service engineers, and knowledge of the alternate costs and effects on construction completion. Equipment procurement It was decided in early 1983 to build the ore milling facility with Oracle Ridge equipment, augmenting it with used equipment

Jan 2, 1989

By Yongqin Zhang

A single bubble released into surfactant solution first accelerates, reaching a maximum velocity then decelerates to reach a terminal velocity. Modeling this "velocity profile" is fundamental to understanding the motion of bubbles in flotation systems. This contribution considers the terminal velocity. Modeling is by a combination of the Navier-Stokes equation for flow around the bubble and the Marangoni effect induced by surfactant on the bubble surface. Numerical simulation is shown to agree with experiment for bubbles in pure water and surfactant solutions.

Jan 1, 1999

By Joe Scheuering, Don Poulter, John Trirnble

Closure of the Grey Eagle Mine tailings impoundment is an example of closing a "wet" tailings impoundment at the cessation of milling operations. This paper presents a summary of tailings cover design and construction, tailings deposition sequences to facilitate closure, construction schedules, costs, and post-closure monitoring. Permit requirements which influenced the design and construction of the tailings are summarized. The performance of the cover and post-closure monitoring issues are also discussed.

Jan 1, 1995

By Michael Michaylov, Elana Vlasseva

This paper presents a method for three-phase foam preparation recipe optimization. The pressurized foam is injected into porous media of gob area for prevention and fighting of SPONCOM fires. The method includes laboratory experiments for main foam properties as well as mathematical optimization procedure. Optimization criteria are formulated reflecting foam application purposes. The influence of solid phase on foam heat stability is shown. Results from optimization procedure for four foam agents by varying fly ash consistency of foam are presented. Theoretical basis for original construction of foam generator, specially constructed for of three-phase foam generation, is set u

Jan 1, 1997