Search Documents

By Meliton M. Garcia, Satya Harpalani

The volume of gases produced in major and trace amounts as a result of detonation of explosives in an underground mine was determined. The volumes of major gases (CO, CO2, NO and N02) were measured immediately following detonation, during the mucking operation, and following the removal of muck. Tests to identify and quantify the gases produced in trace amounts were performed following the detonation only. The composition of the gases produced varied significantly depending on the composition of the explosive/blasting agent. An average of 95% of the gases produced were found in the test chamber immediately following the detonation, while 2% was found in the chamber following the removal of the muck. Several compounds were identified in trace amounts. Of particular interest was the detection of benzene, toluene, butenes, ethyl benzene and naphthalene since exposure to some of these compounds, even in trace amounts, could present a serious health hazard.

Jan 1, 1987

By H. Nakazawa, A. S. Malicsi, K. J. Reid, P. J. Ryan, I. Iwasaki, P. W. Weiblen

Precious metals are commonly believed to be recovered along with sulfide minerals in flotation, but a few neutron activation analyses showed that the recoveries of gold and silver were unexpectedly low. Reasons for low recoveries of platinum group metals remained unresolved due to interferences in the analyses. Electron microprobe, scanning electron microscope, and scanning Auger microprobe analyses have identified nickel arsenide minerals in the ore and confirmed a close association of platinum group metals with the arsenide minerals as minute inclusions. These results indicated a need for re-evaluation of flotation procedures that have so far ignored special problems related to arsenide minerals. The electrochemical and flotation behaviors of nickel arsenide and their application to the flotation recoveries of precious metals from copper-nickel bearing Duluth gabbro are presented.

Jan 1, 1987

By Vanessa M. Torres, Lafayette C. L. Freitas, Evandeo C. Silva

This paper shows two applications of artificial intelligence models in process development. In the first application, a heuristic fuzzy correlation can predict flotation behavior in bench scale based on feed characteristics for a high variability copper ore, as well as to predict plant performance for a feasibility project evaluation, minimizing its risk. The second case study shows the use of neural networks to model the iron ore sintering, correlating ore characteristics and operational parameters with sinter properties. With this application, CVRD aims to establish a new step on iron ore product evaluation and customer support.

Jan 1, 1998

By J. D. Lowell

The gold content of prophyry copper deposits ranges from less than .05 gmt (ppm) to more than 1.0 got, and most deposits contain on the order of 0.05 gmt Au. Perhaps the highest grade mineralization which has been found in close proximity to a porphyry copper is the Ok Tedi Gold Cap orebody whose grade falls in the 2-3 gmt Au range.

Jan 1, 1988

By Kal V. S. Sastry

Mathematical and expert system models are being used extensively for mineral process engineering; nevertheless, standardized methodologies for their computer implementation do not exist. In meeting this need, this paper introduces the concept of a process software model, or more specifically an object-oriented software model, and presents a detailed methodology for its development involving software model specification and development. These software models provide a formal basis for the subsequent design and construction of software objects corresponding to the real world process objects.

Jan 1, 1995

By A. R. Bath

During the late 1970s, pilot mining tests carried out on manganese nodules in the Pacific Ocean and metalliferous mud in the Red Sea demonstrated the technical feasibility of deep sea mining operations. However, the production of manganese nodules on a commercial scale is subject to numerous technical problems. As a result, a German-French joint development project has been underway since 1985. This venture focused on three key points: nodule pick-up device, locomotion of self-propelled collectors and hydraulic lifting of nodules. This paper presents the scope of this research and development program, its main results to date and future prospects.

Jan 1, 1992

By John F. Martonik

When OSHA came into existence in 1970, it adopted national consensus standards to improve safety and health conditions in work places. Coke oven emissions, which are proven to cause cancer and respiratory diseases, were regulated by the coal tar pitch volatile standard, adopted from the 1969 edition of the Threshold Limit Values for Airborne Contaminants by the American Conference of Governmental Industrial Hygienists. The coal tar pitch standard, based upon the benzene soluble fraction of total particulates, limits the personal exposure to 200 micrograms of the benzene soluble fractions of total particulate per cubic meter of air. This standard can be classified as a performance standard because only general limits are set which allows the employer to choose for themselves the means to comply. Both the United Steelworkers of America and the American Iron and Steel Institute petitioned the Secretary of Labor to write a new standard for coke oven missions, each thinking the coal tar pitch standard unsatisfactory.

Jan 1, 1980

By C. E. Roessler

Uranium and its decay series are associated with phosphate deposits of marine origin. Uranium concentrations are on the order of 100 to 200 ppm in matrix from the Bone Valley formation of Central Florida and about 25% this value in matrix mined from the Hawthorne formation in North Florida. Occupational radiation exposure due to this source has been under study in Florida since the mid 1970's (Windham, Partridge, Horton 1976; Roessler and Prince 1978). This report is based on findings of an industry-wide scoping survey conducted by the University of Florida during March 1976 through May 1977 and subsequent studies in selected individual facilities. PHOSPHATE MINING OPERATIONS Mining and beneficiation operations are diagramed in Figure 1. At the excavation site, electric powered draglines remove the overburden and expose the phosphate matrix (ore) which is then slurried and pumped to the beneficiation site. At the washer stage of the beneficiation plant, the matrix is subjected to washing and screening. A coarse product, "pebble" is produced and sent to storage piles while the fine fraction is passed through a series of cyclones to remove the clays. The generated clay suspension is sent to settling ponds while the remaining sand-sized fraction is sent to the flotation plant. At the flotation plant, phosphate particles are recovered from the fine sand particles of similar size through several stages of treatment with reagents, agitation and separation of floating and sinking fractions. The high grade concentrate produced is transferred to storage while the sand tailings are discarded. [ ]

Jan 1, 1981

By K. V. K. Prasad

Stochastic simulation has been routinely used for performing risk and sensitivity analyses in a variety of fields. The commonly used means of generating the simulations has been the Monte Carlo approach, which usually employs a Simple Random Sampling (SRS) scheme of the variable distributions. This method is prone to sample clustering and requires a large number of samples to represent the distribution faithfully. This can become problematic for simulating complex processes where it is impossible to run an arbitrarily large number of replicate simulations. The Latin Hypercube Sampling (LHS) method uses a stratified sampling approach that assures representation of the input distributions for any given number of samples. In this paper the LHS and SRS approaches are compared, using a petroleum resource estimation example.

Jan 1, 1994

By Sundar S. Saluja

Efficient and re1iable methods of fragmentation through blasting have been sought ever since the introduction of black powder in mining operations, but the pace of investigation became faster with the discovery of nitroglycerine. The development of modern measuring instruments and the need to blast more rock with the least damage has made the study of blasting mechanics and its application more important, particularly since the oil embargo. Investigations into the practical approach evolved by Daws (1909) and the work done to make it more useful is discussed. The work of several investigators is touched upon with particular reference to the development of computer programs to simulate and optimize blasting operations.

Jan 1, 1986

By B. Dabrowski, J. D. Miller, D. Halbe, J. Hupka

An air-sparged hydrocyclone (ASH) mobile system was evaluated for continuous stripping and recovery of cyanide (the AVR process) from process water at a gold plant site. The ASH unit performed exceptionally well as an absorber. HCN was removed from the gas phase in a single one second pass with an efficiency exceeding 99%. HCN concentration in the discharged gas phase was lower than 10 ppm, which provided for a safe working environment. The stripping efficiency, controlled by the Henry’s Law constant, exceeded 40% in one pass.

Jan 1, 2004

By Roger J. Hornberger, Paul F. Ziemkiewicz, Dirk J. A. vanZyl, Gene E. Krueger, Harry H. Posey, Kim A. Lapakko, Charles H. Buckmam

The Acid Drainage Technology Initiative (ADTI) was initiated in 1995 by federal agencies, the National Mining Association and the Interstate Mining Compact Commission to identify, evaluate and develop cost- effective and practical acid drainage technologies. In 1999 ADTI was expanded through the addition of the metal mining sector group, which began organization efforts in 1998. ADTI addresses drainage quality issues involving metal mining and related metallurgical operations and acid drainage from coal mines, for abandoned, active, and future mines. ADTI is a technology development program. It is not a regulatory or policy development program. The guiding principle of ADTI is to build a consensus among industry, federal and state regulatory agencies. ADTI is focusing these efforts on technology development and technology transfer in the areas of mine drainage sampling/monitoring, prediction, avoidance/remediation and modeling.

Jan 1, 2000

By B. A. Donahue

The results of a survey of 46 West Virginia coal samples, employing the Office of Coal Research-Band coal sewage treatment process, indicated that the Freeport coal and Bakerstown coal from Preston County, Pittsburgh coal from Harrison and Ohio County and the Sewickley coal from Monongalia County offer outstanding potential for water clarification. Oxidation, steam treatment and acid and base washing of coal generally resulted in small positive or negative changes to the water clarification capacities of the coal while the employment of prepared coal fractions resulted in more significant benefits. Of the coals tested, those fractions with high ash, high sulfur and low Btu generally possessed the highest adsorption capacities.

Jan 1, 1968

By Steven A. Moreno

Geochemical returns from commercial analytical laboratories are often delayed because of postal and other bulk distribution inefficiencies. Consequently, minerals exploration programs are handicapped due to insufficient time for treatment, analysis, and diagnosis of the data. The minerals industry lacks a system for rapid transmission of geochemical data which allows immediate entry into statistical and plotting routines. Over the past three years, Houston International Minerals Corporation (HIMCO) has developed a computer-based system to receive, treat, and distribute geochemical data. In the past two years, Bondar-Clegg (Denver) and Chemex (Vancouver) have developed systems to transmit' data directly to HIMCO via the world-wide Boeing Computer Services (BCS) network. The main benefits to HIMCO have been ten less days for reporting turnaround, ten less days for keypunching, less data handling, accuracy. The benefits to the laboratories have been improved in-house data management, reporting, and HIMCO's increased geochemical activity.

Jan 1, 1982

By Harold B. Goldman

On the basis of tonnage, the sand and gravel industry is the second largest nonfuel mineral industry in the United States. In 1990, the production of sand and gravel was 927 Mt valued at $3.4 billion. California, which leads the nation with more than 126 Mt, together with Texas, Washington, Michigan, and Ohio, account for 36% of the total production in the nation (Table 1). In commercial usage, sand applies to rock or mineral fragments ranging in size from particles retained on a No. 200 Sieve (0.074 mm openings) to those passing a No. 4 Sieve (4.76 mm openings). Gravel consists of rock or mineral fragments larger than 4.76 mm, ranging up to 88.9 mm maximum size. The construction industry consumes 97% of the sand and gravel produced; the remainder is sand used for specialized products such as glass (see chapter on Industrial Sand and Sandstone and Glass Raw Materials). Utilization The building industry uses sand and gravel chiefly as aggregate in portland cement concrete, mortar, and plaster; the paving industry uses sand and gravel in both asphaltic mixtures and portland cement concrete. Aggregate is commonly designated as the inert fragmental material that is bound into a conglomerate mass by a cementing material such as portland cement, asphalt, or gypsum plaster. Sand and gravel is also used as construction fill, road base and subbase, and decorative material. Portland Cement Concrete Aggregates: Portland cement concrete consists of sand and gravel surrounded and held together by hardened portland cement paste. Concrete mixes commonly contain 15 to 20% water, 7 to 14% cement, and66 to 78% aggregate. Sand and gravel used as concrete aggregate have to meet many requirements (Goldman and Reining, 1983). Premature deterioration of concrete has been traced in many instances to the use of unsuitable aggregates. Asphaltic Aggregate: Asphaltic mixtures used predominantly for paving consist of combinations of sand, gravel, and mineral filler (material finer than 0.076 mm), uniformly coated and mixed with asphalt produced in the refining of petroleum. Sand and gravel used as asphaltic aggregate must meet the same general physical requirements as materials used for portland cement aggregate. GEOLOGY General Requirements of Aggregates Construction aggregate has many requirements that are difficult to meet if only unprocessed material from natural deposits is used. Suitable material is composed of clean, uncoated, properly shaped particles that are sound and durable. Soundness and durability are terms used to denote the ability of aggregates to retain a uniform physical and chemical state over a long period of time so as not to disintegrate when exposed to weathering and other destructive processes. Individual particles must be tough and firm, possessing the strength to resist physical stresses and chemical and physical changes, that may cause swelling, cracking, softening, and leaching. The aggregate should not be contaminated by excessive clayey material, silt, mica, organic matter, chemical salts, and surface coatings. Physical Properties: The quality of aggregate depends upon its physical and chemical properties. These, in turn, may be inherent mineralogical and textural features of the rock or may be the effects of later changes such as tectonics, mechanical or chemical weathering, or incrustations. The physical properties most significant for concrete use are: 1) abundance and nature of fractures and pores, 2) particle shape and surface texture, and 3) volume changes which may occur because of freezing and thawing or wetting and drying. An aggregate is considered to be physically sound if it is adequately strong and capable of resisting the agencies of weathering without disruption or decomposition. Minerals or rock particles that are physically weak, extremely water absorptive, and easily cleavable are susceptible to breakdown. The use of such materials in concrete reduces strength or leads to early deterioration by promoting weak bond between cement and aggregate, or by inducing cracking, spalling, or popouts. Severely weathered, soft, micaceous, or porous materials may cause localized stresses to develop in concrete by swelling and shrinking during wetting and drying or freezing and thawing cycles. Physical Suitability of the Various Rock Types. Sedimentary rocks have a wide range in physical and chemical qualities. Sand- stones and limestones, if hard and dense, are ordinarily satisfactory, but many sandstones are friable and excessively porous and commonly are clay-bearing. Shales generally make poor aggregate material, being soft, weak, and absorptive. Most igneous rocks are satisfactory, being normally hard, tough, and dense. Tuffs and certain flow rocks may be extremely porous and have high water absorption and low strength. Metamorphic rocks differ in character. Most quartzites are massive, tough, and dense. Fine-grained marbles are usually durable, but coarse-grained marbles have low abrasion resistance. Gneisses are ordinarily very tough and durable. Some schists contain micaceous minerals that are undesirable because they are soft, laminated, and absorptive. Micaceous minerals are susceptible to splitting along cleavage planes and thereby impair particle strength and durability. Some schists and slates in particular are thinly laminated and tend to assume flat slabby shapes that lack strength-and do not pack well. Any or all of these rock types may be rendered undesirable because of harmful exterior coatings. Weathering processes, particularly the action of ground waters, deposit these coatings. The most common coatings are calcium carbonate, clay, silt, opal, chalcedony, iron oxide, manganese oxide, and gypsum. Particles with these coatings are undesirable as aggregates because the bond between particle and coating may be weak, and decreasing the strength of the aggregate-cement bond.

Jan 1, 1994

By Deepak Malhotra, William F. Riggs, Edward C. Dowling

INTRODUCTION Mining companies are In the business of making an acceptable profit on their Investments, It became obvious in the recent recession that economic profitability/viability depends on being the lowest cost producer In order to compete on a global basis. The burden of achieving this objective falls on the mineral manager. He must strive to produce a salable product in an environmentally acceptable process while continuously Improving the profit margln.(1,2) Metal prices fluctuate on a regular basis. They directly Impact revenue and hence operating philosophy. The mineral engineer needs to develop an optimum operating strategy to meet his overall objectives, One would expect that, In the modem era of complex computer models, it would be easy to develop an economic model to maximize profits and/or cash flow. Discussions with mill managers Indicate that one mine/corporation's optimum operating strategy is not necessarily optimum for another. This paper approaches the problems from basics "Economics 101" and Illustrates the complexity of developing a universal model which can be applicable to all mines. Case examples are used to illustrate the need for better communication to avoid the basic economic fallacy “that optimization of segments leads to optimization of the whole system.” TECHNICAL MODELS Technical models are a prerequisite to the development of economic models because they provide the necessary Input data to these models, The flow of material from a mine through the sale of the finished product is shown In Figure 1. The ore Is mined and milled, and the concentrate can be stored for sale or smelted and refined In-house or at a toll facility. The finished product(s) are held In Inventory until sold either through existing contracts or in the spot market. [ ] Fairly reliable technical models have been developed for mining, milling and smelter operations. Mine plans are developed to provide a good Indication of the relationship between production and cut-off grade. It is easier to change surface mine plans than plans for underground mines. However, there are limits to maximum production that can be achieved with existing equipment. It Is possible that mine benches may not be developed to handle additional equipment, even If It was purchased to enhance production. More often than not, the cut-off grade Is lowered to Increase throughput goals.

Jan 1, 1993

By M. K. LeBegue

Water sprays located behind the bits of cutter drums have been shown to reduce the incidence of face ignitions. This paper details the design approach to successfully incorporating water seals into a drum miner cutter head.

Jan 1, 1999

By W. C. Smith

Even with the most conservative mine plan, rib instability can occur unexpectedly, and if not adequately dealt with, can progress from a nuisance to a major safety hazard. This Bureau of Mines paper examines the mechanisms of progressive rib failure in high mine openings and discusses techniques to control rib slabbing. A field test site in a longwall mine was instrumented to investigate rib behavior during mining. While data analysis showed minor pillar dilation, sporadic zones of progressive rib instability were detected which culminated in eventual rib failure. The failure occurred despite conservative pillar dimensions and shallow depth. Physical and computer models were used to demonstrate the mechanisms of rib failure and then evaluate the influence of support and other mine-related parameters on rib behavior.

Jan 1, 1989

By Joseph Kurtak

When prospectors discovered mineralized outcrops in Pine Creek Canyon in 1916, little did they know the site was destined to become one of the world's greatest tungsten mines. Located outside Bishop in California's rugged Sierra Nevada mountain range, the mine's development imposed unique challenges to the hardiest of mining men. In its early years, the Pine Creek operation was plagued by bad luck and poor timing. But through the perseverance of a dynamic group of mining personalities, it would gain world class status. Pine Creek tungsten supplied much of the defense needs of the United States during World War II and put the Bishop area on the map as a major contributor to the nation's stockpile of strategic metals. The mine's history was shaped by world politics, the ups and downs of metals demand and economic survival through technological innovations. In contrast to many mines, Pine Creek's workings went horizontally into and then up inside the mountains - nearly to the ridgetops. This resulted in the name "Mine in the Sky" being attached to the operation. The origin of Pine Creek's ore bodies is related to the emplacement of a portion of the Sierra Nevada batholith about 100 million years ago. During the intrusive process, granitic magmas engulfed overlying calcareous sedimentary rocks, flooding them with silica-rich hydrothermal fluids and metamorphosing them to skarn. The fluids also contained tungsten, molybdenum and copper. They precipitated as scheelite, molybdenite and chalcopyrite, respectively, during the metamorphic process. The ore-bearing skarns occur as near-vertical tabular pendants in the intrusive rocks. These were later exposed by the uplift of the Sierra Nevada mountain range and glacial erosion.

Jan 1, 1998

Federal Regulations require that coal producers conduct a written, in-house investigation with every lost time injury accident. Besides their obvious value in accident prevention, competently conducted investigations can provide a number of additional benefits to include positive supervisor involvement, the control of rising worker's compensation costs and a measure of protection from civil/criminal proceedings. The paper describes such topics as MSHA minimum requirements, investigator selection and training, accident site procedures, witness interview techniques and the management review process. The reader is also presented with a number of information resources available through MSHA, the National Safety Council and other sources.

Jan 1, 1995