Search Documents

By P. Corser

Operational and geotechnical constraints on mining within steeply dipping deposits and historic landslide areas, which are characteristic of subarctic coal deposits in Alaska, will be discussed. The current plan for mining through these areas will be presented, as well as an alternative plan for minimizing the adverse effects of mining through an historic landslide area.

Jan 1, 1988

By Jeroen van Eldert, Daniel Johansson, Henrik Ittner, Håkan Schunnesson

"Numerous aspects of underground construction, from structural stability to construction costs, depended on the tunnel quality, including blast damage and the Excavation Damage Zone. Accurately quantifying the extent and severity of damaged rock is a problem. Recent technical developments in the field of Measurement While Drilling (MWD), including software for on-board logging and on-site analysis, have shown potential for rock-mass characterization. Ground Penetrating Radar (GPR) and P-wave velocity measurement have also improved and show similar potential. This paper explores the use of MWD, GPR and P-wave velocity measurements and uses them in techniques for excavation damage characterization and prediction. The paper is based on data collected from a small underground waste-collection site in central Stockholm, Sweden. The data is correlated against rock-mass characteristics and their responses are evaluated. Results indicate potential for excavation damage characterization for all tested techniques, which could minimize blasting damage and improve the over-all tunnel quality. 1 INTRODUCTION During underground excavation the rock mass is influenced in many ways. The Excavation Damage Zone (EDZ) is a result of these influences. The EDZ can be defined by an irreversible change in rock mass properties, for example increased permeability. EDZ is influenced by the excavation method, the rock mass properties and the in-situ stresses in the area of the tunneling. Since the 1990s research has been done on the EDZ by Emsley et al. (1997), Christiansson et al. (2005), Olsson et al. (2009), Ouchterlony et al. (2009), Ittner et al. (2014), and Siren et al. (2015). Based on past literature the EDZ have in this paper been separated in the following subzones: 1. Failure Zone or over-break is the area outside the planned tunnel profile, including the Look-Out and hole deviation. This zone consists of fracture networks (both natural and blasting-induced), that caused rock fall-outs. The extent of the over-break can be determined by volumetric scanning and photogrammetry and the half cast factor can be used as a damage indicator. 2. The Damaged Zone is split into three parts and but the quantity and depth of damage is difficult to measure. Although it can be visualized by sawing of rock slices in the tunnel wall (Olsson et al. 2009), diamond coring (DC) or P-wave velocity reduction (Jern 2001): a. Inner Damage Zone (Crush Zone): It is located directly around the drill hole, and is caused by the shock-wave energy of the detonation. The micro fractures in the Crush Zone produce a white-wash (rock dust) in the half cast. b. Transition Zone: This zone consists of micro fractures that connect and form macro fractures, both radially and parallel to the tunnel wall. The macro fractures are caused by the gas expansion during the detonation of the explosive; it increases the pressure in the (micro) fractures and creates the macro fractures. Seismic reflection, rock slicing and core drilling can be used for the examination. c. Progressing Zone: In this zone the existing radial fractures propagate due to the increase gas pressure inside these macro fractures. Examination methods are seismic reflection, rock slicing and core drilling. In addition, the Peak Particle Velocity (vibrations) could be used to estimate the depth (Tesarik et al. 2011)."

Jan 1, 2016

By W. Petruk

Imaging is a fundamental requirement when characterizing minerals, ores and related products. Images are used for presentation, texture analysis, characterization, image analysis, identification, etc. The image mode that is utilized is dependent on the application, mineral properties and available instruments. Different instruments produce images that display different features. In order of increasing complexity they are: hand specimens, a non-polarizing microscope, polarizing optical microscope, scanning electron microscope (SEM), low vacuum SEM, microprobe, secondary ion mass spectrometer, staining, cathodoluminescence, tomography and others. Image analysis uses images produced with either an optical microscope or a SEM, but the SEM images are superior in this application. Key words: Mineralogy, Imaging, Mineral characteristics, Scanning electron microscopy, Optical microscopy, Cathodoluminescence

Jan 1, 2003

By G. Newman, C. D. Sellars, E. A. Portfors

Power for mine operation in remote locations is usually provided by diesel generators. For gold mines where processing is normally desirable on-site, power requirements can be significant and the operating cost for diesel generation then becomes an important factor in mine feasibility. If a suitable site is available, a small hydroelectric power facility near the minesite can provide a significant portion of the mine power requirements. The hydrological, engineering and economic factors involved in small hydroelectric power development are described in this paper. Capital costs are minimized by run-of-river hydro development which does not require a dam and reservoir and has less environmental impact. During periods of low flow, diesel generators are used to make up the power demand. The hydrologic analysis required to determine unit energy costs is described and technical requirements for linking the hydroelectric power facility with diesel generation are outlined. Case studies are presented demonstrating the economic advantages of a small hydro installation. One case study is for a proposed gold mine in British Columbia and the second is a large operating gold mine overseas, for which the hydroelectric power scheme is presently under construction .

Jan 1, 1987

By John A. Herbst, Kuang Y. Lee

Coarse particle size measurement is essential for the automatic control of a size reduction process like crushing or SAG milling in order to achieve optimal process performance. However, the on-line size measurement of coarse material is not easily obtained due to the problems of material handling and sample statistics. A technique based on advanced image analysis and quantitative stereology has been successfully developed and tested in a pilot scale setting. The chord length distribution of coarse particles on a moving conveyor was measured with an image analyzer and then transformed to the mesh size distribution with a stereological model and a special numerical method. Some test results as well as the technique's industrial suitability and limitations of this method are also discussed.

Jan 1, 1992

By J. Bacho

The modern drilling fluids industry is a dynamic, evolutionary environment. It is continuously striving to satisfy and anticipate the ever-changing needs of the oil and gas industry. The predominant driving forces in the industry over the past decade have changed dramatically. Health and environmental issues, coupled with economic and performance requirements, demand innovation and change from the drilling fluids industry. Emerging drilling fluid technologies will demand environmental considerations from mined components with additional emphasis on cost and performance criteria. Drilling fluids providers continue to search for and identify environmentally sensitive components which meet or exceed the performance of their more toxic predecessors. These changes have and will impact the components of drilling fluids that are mined.

Jan 1, 1994

By William H. Pomroy, Annie M. Carigiet

This U.S. Bureau of Mines report is an analysis of underground coal mine fire incidents occurring in the United States during the 15 years from 1978 through 1992. The fire data used in this analysis were obtained from Federal Mine Safety and Health Administration (MSHA) mine fire investigation reports. Fires were analyzed by year, state, coal bed thickness, mining method, evacuation measures taken, ignition source, burning substance, location, equipment involved, detection method, time of day, number of injuries and fatalities, and method of extinguishment. In all, 164 fires are reported, or an average of 10.8fires per year. The most common ignition source was electricity, the most common burning substance was coal, the most frequent fire location was the belt entry, belt conveyors were the most common equipment involved in fires, and water was the most common extinguishing agent.

Jan 1, 1995

By Terry Owen

Business development process. Throughout Cyprus Amax's early months in Russia, the company stayed focused on what was needed from a deposit for economic success. Cyprus Amax's reason for success in Russia is that all involved - its Russian partners, the workforce and expatriates - provided a focused effort that served the project as it worked through the tender process and the Russian regulations. The company developed an understanding of the regulatory process by working with solid, ethical partners. Infused into the Kubaka management structure were Russians with the knowledge to facilitate the process and a professional group of expatriates. Developing credibility and a solid rapport with the Russian mining authority was critical to the success of this venture. Identifying and gaining the trust of key Russian individuals was also critical during the early stages. Gaining their trust and building credibility was part of the process. These key Russians were brought to the United States to visit existing Cyprus Amax mines. These efforts proved valuable in building an understanding with the Russians about the kind of company Cyprus Amax is and the kind of efficient operations that it can run. This was a learning process for all parties. Fortunately, the company was dealing with intelligent and educated people.

Jan 1, 1997

By Paul Sainato, J. Steven Gardner

Sustainable development is defined as ‘development that meets the needs of the present without compromising the ability of future generations to meet their own needs.’1 There has been considerable debate of late between environmentalists and mining operators concerning the current regulation and operation of mountaintop mining. To those not familiar with the practice, it essentially applies an area mining method to a mountaintop, removing all overburden above coal seams, resulting in full recovery of the resource with the excess or swell spoil material - (rock and dirt) being deposited in engineered fills in hollows to the side (known as hollow fills or valley fills - very similar to highway fills). Because most of the dialogue has been adversarial and mining’s response is perceived to be primarily reactive instead of proactive, a rift in communication and value systems between the two sides has widened. Since 1999, the global mining community has been concerned that there is a disconnect between mining practices and the values of today’s society.3 Working through the World Business Council for Sustainable Development (WBCSD), the International Institute for Environment and Development (IIED) was created to review mining practices in a project entitled Mining, Minerals and Sustainable Development (MMSD) driven by the following four goals:

Jan 1, 2005

By R. Cook

Knowledge based applications are becoming important to Associated Manganese for efficiently dispatching ore of appropriate grades to customers on time. The G2 expert system shell has been used to develop blending and scheduling applications using a combination of object-oriented rule based, procedural, and heuristic approaches. The blending application, for example uses a heuristic approach for creating blends from thousands of small stacks of manganese ore of various grades and sizes, to meet customer specifications while fully exploiting the available inventory. Data capture and data warehousing have become important issues, and the Internet shows strong potential for distribution of pre-processed information.

Jan 1, 1997

By [Miroslaw] M. Hajdasinski

The Payback Period (PBP) is one of the most widely applied project evaluation criteria 'in the mineral industry. As much as this criterion is liked by practitioners, it is also criticized by academicians who seriously question its validity. Inspired by this criticism, the author of this paper examines the classical definition of the PBP criterion, and formulates a new one designed for both investment and borrowing projects. It is demonstrated that the PBP, in its revised version, is free from all the shortcommings of the old one, and is fully compatible with the Net Present Value (NPV) criterion, as well as with all the other NPV compatible project evaluation criteria. Since the traditional approach to the comparison of mutually exclusive projects (MEP1s) by means of the PBP criterion has been incorrect, the paper also outlines the correct approach to this problem. Finally, owing to the fact that the PBP depends on the assumed interest rate, and using a specially developed computer program, the PBP is graphically presented, in six numerical examples, as a function of the interest rate.

Jan 1, 1989

By Bekta? Uz

Istanbul is the bigest metropolitan city of Turkey with more than 15 millions of population and construction activities are steadly increasing with respect to that increase in population. In this papaer petrographical, physico-mechanical properties of natural aggregate mines from west, (Tekirdag) to East, Izmit (Gebze) 'will be summarized in connection with the concrete production. However the locations suitable for aggregate production in these area as; Paleozoic aged sandstones (Ayazaga, Cendere, Mahmutbey areas), Permb-Carboniferous aged limestones (Cebeciköy area), Triassic limes tones (Ömerli-Gebze areas) and Eosen limestones (Çatalca area), Plio-Quaternary aged volcanic basalts (Tekirdag, Çorlu, Beykoz areas). Plio-quaternary aged, fine grained aggregates within sandy formations are mined in Silivri-Sinekli area, Catalca-Ormanali area, Agacli-Akpinar (Kemerburgaz area) and Sile-Karakiraz-Sahilköy areas. Sandstones mineralogically contain mainly of Quartz+Feldspar and less amount of Mica (biotite+muscovite) rich with slica content and sedimentary origined. Especially limestones are cryptocrystaline textured, unique mineral composed of calcite and secondary have Dolomite ± (Quartz+Albite). Basalts are microlitic textured and contain Olivine+Pyroxene+Plagioclase. Chemically basalts rich with Fe and Mg and also volcanic origined. Sands are fine grained natural aggregates mainly contain semiangled, rounded minerals and rock fragments. Mineralogically have Quartz + Feldspar ± pyroxene+ ambhibole ±garnet and less amount of epidote ± magnetite ± hematite. Different rocks, used in aggregates such as limestones, sandstones-sands and basalts, supply varied concrete strength because of their mineralogical composition and characteristics of textures. Moreover, Basalts (Karatepe area) are good example for the higgest concrete strength (1017-1895 sc; kg/cm2) in our study area because of their clambed mineralogical apperance such as intersertal texture. As the result of extensive field and comparative laboratuary studies, the effect of petrographic, physical, mechanical properties of the aggregates on concrete srtength is extensivelly discussed in this paper.

Jan 1, 2005

By J. G. Henning, R. Edrissi

This paper describes a practical methodology, based on numerical modeling, for the prediction of progressive failure of underground-mine stopes having cable-bolt support. A case study of the 40-761 scope at the Kidd Creek mine, Timmins, Ontario, Canada is presented. Scope 40-761 was mined by blast hole open sloping in 1986 and was a lead scope within a mining block located between levels 36-1 and 38-2. Initially designed to peak at level 38-2, the scope back caved upwards =40 m towards level 36-1. After caving began, cable bolts were installed above the stope from level 36-1. The stope eventually stopped caving when the falling rock mass encountered a sufficiently high cable density. This paper provides details of the geomechanical data and modeling results of the case study. Numerical modeling of cable bolts around the mine stoke was carried out using a finite-element modeling software. The software, known as e-z tools, was developed by the first author.

Jan 1, 1996

By Ralf Vergeiner

The most famous landmark of the city of Graz (Austria) is the clock tower on the castle hill. An underground chamber was built as a multifunctional structure beneath this landmark. The required structure was designed as cavern. The overburden to the clock tower in the north side of the cavern was only 30 m. To allow access from the city to the chamber and the clock tower, a vertical shaft was built near the cavern. Rock excavation was by drill and blast method. The pilot shaft was made by the raise-boring method. Because the location of the building site was in the center of Graz, special care was taken to minimize deformations and vibrations so as to protect surrounding buildings.

Jan 1, 2001

By D. Krzyszton, P. Czaja

Mining explosions in rocks originate stress waves of great intensity, which crush the surrounding rocks and are then propagated as a seismic wave. Seismic waves are the cause of dynamic loading of pillars and their subsequent destruction. In calculating safe dimensions for inter-room pillars, not only the stresses conditioned by overburden pressures should be taken into consideration, but also the dynamic stresses caused by explosion. This is of particular importance for pillars with great specific acoustic impedance which have been destroyed mainly by the reflected seismic wave. It is possible to take dynamic loading into consideration in the calculation of pillars when the parameters of the propagation wave, the dynamic elastic constants of rocks, the strength properties of rocks, the strength properties of rocks subjected to dynamic loads and the parameters of the blasting charge are known. An example of the calculation for the safe width of an inter-room pillar subjected to the seismic effect of an explosion is given and the possibilities of reducing the dynamic loading of pillars are discussed.

Jan 1, 1982

By Samir Kumar Das

Presently Geographic Information System (GIs) is gaining wider acceptance id appreciation in various resource management surveys, generation of various thematic maps, various scientific investigations, environment assessment, disaster management, etc in India but they are general in nature. A huge number of Global Positioning System (GPS) based "Total Station" are playing good roles in India for accurate and quick surveying . The GPS based real time Mine Management and Truck Dispatching System for optimization of productivity is being installed in the Panchpatmali opencast bauxite mines of India. This paper dealt in depth on GIs and GPS and their present roles in the Indian mining scenario.

Jan 1, 2002

By M. Ruonala

The Larox Power PF Pressure Filter has been developed to meet the challenges of ever increasing output tonnages demanded by the minerals processing industry. This paper will highlight recent experiences at the Rudna Copper Concentrator in Poland, the Escondida Copper Concentrator in Chile and some large zinc concentrators in Australia. Detailed maintenance and operating cost information will be disclosed. Emphasis will be placed on economics on scale gained from higher machine throughputs.

Jan 1, 1998

By E. Pardo-Igúzquiza

Most mining applications of geostatistical simulation are to the simulation of quantitative variables, such as grade. In many instances the occurrence of quantitative variables and the values they take are controlled, at least partially, by qualitative, or categorical, variables. Examples include quartz-vein controlled gold orebodies and stratigraphic silver/lead/zinc deposits. In these cases a realistic simulation must include geological controls on the spatial distribution of the simulated quantitative variables. This paper describes extensions to, and algorithms for, the truncated plurigausian method of simulating categorical variables. The categorical variables are modelled as indicator random functions that represent the presence/absence of the variable at spatial locations. Stochastic images of the distributions are obtained by truncation of realisations of two Gaussian random functions simulated at the same locations. Parameters required are the thresholds for truncation of the Gaussian variables and the covariance structure of each Gaussian random function. These parameters are estimated from the experimental proportions of each variable and indicator direct and cross semi-variograms. A detailed case study is shown in order to illustrate the procedure, to discuss the results and to present the algorithms for plurigaussian simulation.

Jan 1, 2002

By Arpad E. Torma

The electrochemical behavior of a zinc sulfide concentrate during the microbiological leaching was investigated using ZnS-carbon paste electrodes and a cyclic voltametric technique. The effects of Zn2 [ ] , Fe2+, Fe3+ and Cu2+ on the cathodic and anodic currents associated with zinc sulfide leaching in presence and absence of microorganisms, were assessed. The semiconductor nature of zinc sulfide was discussed in terms of ability of microorganisms to obtain their metabolic energy (through removal of electrons) from this high energy gap substrate. The intermediate electrochemical reactions involved in the ZnS leaching were described.

Jan 1, 1989

By Leslie E. Apodaca

INTRODTUCTION The use of spiral concentrators for processing fine coal particles is an old idea that has recently gained acceptance in the 11.S. coal industry. It was not onti1 the Australian Minerals Industry developed a spiral concentrator specifically for separating coal from ash in the latter 1970's and early 1980's that spiral concentrators were seriously considered as viable equipment for processing fine coal. The Wright Coal Spiral was introduced in 1980, the Mineral Deposits Limited Mark 10 Coal Spiral was introduced in 1982, and the Vickers Wyong Coal Spiral was introduced in the latter part of 1984. Each spiral design was different and utilized constant profile troughs, constant pitch troughs, compound profile troughs, and various splitter arrangements. Mineral Deposits Limited has combined the best features of the compound profile trough and constant pitch trough with critically-placed splitters to develop the MDL LD4 spiral concentrator which is a truly efficient coal washing spiral. This spiral concentrator was introduced into the U.S. Coal Industry in 1987. Recently, Mineral Engineering Technology of the United Kingdom and Multotec of South Africa have introduced their own coal spiral designs. Spiral concentrators were first installed in fine coal processing circuits in the Australian, South African, and Canadian Coal Industries in the early 1980's and in the U.S. Coal Industry in 1985. SPIRAL CONCENTRATOR SEPARATION PROCESS The separation process that occurs within the spiral concentrator trough is very complex, as it is a combination of three gravity separation processes. When the coal slurry first enters the spiral trough, each coal and ash particle and the water is subjected to centrifugal forces. These forces cause the water, light coal particles, fine heavy ash particles, and medium middlings particles to the outer vertical portion of the spiral trough. The coarse ash particles and the coarse middling particles remain on the inside of the spiral trough. The center or transitional area of the trough contains a mixture of middlings particles and near-gravity material that is present in the slurry, as shown in Figure 1. At the same time the coal and ash particles are suhjected to centrifugal forces, the trough design (both profile and pitch) causes the particles to be subjected to flowing film and stratified bed separations. The combination of these three separations, whose efficiency is dictated by the spiral troogh design, will effect the separation of the lighter coal particles from the heavier ash and middlings particles. As the slurry flows down the spiral, the profile and pitch design of the trough will counteract the centrifugal forces on the fine, heavy ash particles and fine middlings particles and cause them to migrate from the vertical portion of the trough to the center or inner portion of the trough. At the same time, any heavy particles trapped in the transitional area of the trough will be forced to migrate to the inner edge of the trough and any coal particles will be forced to migrate to the outer edge of the trough. SPIRAL SPLI'TTEP ARRANGEMENT The critical placement of splitters along the inner edge of the trough for removal of the heavy ash particles as the slurry flows down the trough further enhances the separation of the coal particles. At the bottom of the spiral trough are product splitters arranged to make a final separation of the slurry stream into clean coal, middlings, and refuse products.

Jan 1, 1988