Search Documents

By W. J. Schlittler

Auxiliary Equipment pumping systems to support primary, secondary and regrind grinding circuits will be the primary focus of this paper. Every grinding system is unique and requires special design considerations for proper application of pumps to transport mill discharge. To satisfy the majority of applications, a new series of pumps has been developed by Svedala, known as World Class Pumps. Selection of these newly developed pumps for each type of grinding circuit will be presented. Specific components of selection are materials of construction, piping system, classification method, material characteristics and slurry characteristics. Both horizontal and vertical pump applications will be reviewed with emphasis on rules of pump piping and sump design.

Jan 1, 1999

By Christoph Schulte-Schrepping, Bou-Young Youn, Rolf Breitenbücher

"The main requirements of two-component grouts are a high workability and sufficient stability against sedimentation with a retention time of more than 72 hours, as well as a rapid strength development im-mediately after grouting. Component A usually consists of OPC, water, bentonite, and retarding agent. Component B, a liquid accelerator, is added to Component A during grouting at the end of the shield tail. Current investigations on different compositions of Component A showed a high workability lasting for at least 72 hours. The workability could be extended with increasing amount of the retarding agent to a certain degree. An increase of the bentonite content improved the stability of the mix, but had a negative impact on the flowability respectively the workability of Component A. High compressive strengths could be rather achieved by an adapted mixing ratio of Component A and B than by increasing the amount of the accelerator. Thereby, the interactions and compatibility of the selected constituents play an essential role. INTRODUCTION In mechanized tunneling with segment linings, the annular gap between segment ring and soil must be filled instantaneously with an adequate grouting mortar. The main functions of the annular gap grouting are to stabilize the tunnel lining and to minimize settlements of the ground surface at the same time. Thereby, two contradictory requirements are demanded on annular gap grouts: On the one hand a high workability and sufficient stability against sedimentation, on the other hand a rapid strength develop-ment immediately after grouting. Besides single-component grouts, which achieve the necessary stiffen-ing by dewatering into the surrounding soil, two-component grouts are used, especially in cohesive soils with a very low permeability. Basically, annular gap grouts are almost exclusively defined on empirical basis. Fundamental studies about the constituents and composition of the grout as well as the related achievable properties are still missing so far. Therefore, it is necessary to investigate the material-specific correlations regarding the relevant parameters of annular gap grouts – workability and flowability, stability of the mix as well as strength development – in comprehensive experiments. Based on the knowledge gained from the investigations, it should also be possible, to perform the grouting material according to a real design concept and thus, to ensure an adequate grouting in prac-tice considering the geological and hydro-geological conditions."

Jan 1, 2016

By F. Habashi

The Republic of South Africa is a heterogeneous mixture of Black Africans, Afrikaans, British, Indians, Malayans, French Huguenots, and many others from Europe and Asia. A decisive date in its recent history is the collapse of the Apartheid Regime in 1994. For a metallurgist, South Africa is the country of diamonds, gold, platinum, and many other metals. In 1887 Cecil Rhodes (1853-1902) was able to take control of the De Beers Mining Company after the discovery of diamonds at Kimberly in 1866. It was there where the so-called School of Mines was inaugurated in 1896.

Jan 1, 2010

By David M. Mchaina, Allan E. Hall, Siegfried Rohr, J. D. Botsford

Incidents associated with secondary dust ignitions in the mining of massive sulphide ore deposits are of major concern in Canadian underground metal mines. During stope or development blasting, a highly concentrated cloud of sulfide dust is created and may be ignited, resulting a secondary explosion which releases a considerable volume of sulphur dioxide and possibly other sulphur gases. The consequent pressure, heat and toxic gases can result in loss of life, significant damage to equipment and loss of production. These losses are expensive and should be prevented. Explosions of this type have occurred at the H-W mine of Westmin Resources mainly in the development headings and cut and fill stapes. This paper presents the results of a study conducted at the H-W mine to compare dust sampling methods for explosivity tests. The associated benefits and pitfalls of each sampling technique are examined. The investigative work conducted to develop and test preventive and control methods against sulphide dust ignitions is also discussed. The techniques which will minimize the risk of sulphide dust ignition in metalliferous mines are outlined. A review of current preventive and control measures practised at the H-W mine is also presented.

Jan 1, 1989

By LeRoy Kienitz

There may be someone here who is not required to run his equipment at its maximum capacity. There may be some fortunate enough to have more crushers than needed, wider conveyor belts than required, and other mill equipment equally oversize. If so, then this paper will have no interest for him; but if most of you are in the situation we in the aggregate producing industry are in, then you probably wish to crowd your mill equipment to its limit. When you do this you must watch for block-up and overloads of all sorts. You need more eyes than you have to guard the critical points. The human eyes that now do nothing much, but watch should be freed for more productive work.

Jan 1, 1961

By Michael Francis, Chris Darton

More than 55 km of tunnels have been constructed by TBM in the last 12 years to refurbish and upgrade the high voltage cable network in London. These include a tunnel of 20km length using EPBM machines in both clay and granular soils. Route selection was made with reference to subsurface structures, existing ground conditions, using suitable shaft locations addressing environmental concerns. The complex interfaces to manage included obtaining of consents to the coordination of multiple suppliers. The paper describes how all these challenges have been met successfully and how technology has been employed to provide for safe construction and operation in the congested urban environment.

Jan 1, 2003

By Jerry Peterson

Mine maintenance planning, scheduling and daily workflow communications are crucial elements for enhancing overall efficiency and reducing costs. Equally important, it helps identify time periods that equipment will be unavailable so conflicts with production demands are avoided. The current CMMS Kennecott Energy Corporation (KEC) utilizes does not perform these functions in an effective manner. A solution to this problem was to develop an intuitive web-based maintenance planning, scheduling and work flow system call E-MESA. This paper will discuss the E-MESA'S system structure and advantages and disadvantages of using the web based E-MESA solution to perform the maintenance functions described above.

Jan 1, 2002

By R. V. Ramani, K. V. K. Prasad

Forecasting mined grade variability from exploration information is a challenging task in mine planning. For effective planning of activities, such as workplace scheduling, ore grade quality control, etc., development of realistic numerical simulation models of in situ variability from exploration information is an essential first step. Geostatistical conditional simulation (GCS) is one of the well known methods to develop such simulations. Recently, stochastic fractal models based on the assumptions of scale-invariance and self-similarity have been used for developing simulations of several natural phenomena. It has been suggested that these models might permit the generation of short-scale variability information from exploration data with greater fidelity when the data satisfies the attendant assumptions. In this paper, stochastic fractal models are reviewed, and their relationship to geostatistical variogram models is examined. A comparison of the two simulation techniques has been performed using coal sulfur data from a mined-out coal property. The results of this comparative analysis are also presented in the paper.

Jan 1, 1993

By J. G. Groppo, B. K. Parekh

Column flotation testing was conducted on the flotation feed slurry obtained from a preparation plant located in the Southern Illinois coal basin. The column flotation tests were conducted using three different bubble generating devices: a static sparger, a gas saver and a foam jet. Each of these devices was tested with three different types of frother and various column operating variables to provide maximum combustible recovery, minimum product ash and maximum pyrite rejection. The results show that column flotation provided improved flotation performance, in terms of combustible recovery as well as ash and pyrite rejection, for each of the bubble generating devices. However, the effectiveness of each bubble generating device was dependent on the type of frother used. Alcohol frothers were most effective for use with the static sparger, somewhat less effective for the foam jet and ineffective for the gas saver. Glycol frothers were effective for all three bubble generating systems, providing high combustible recovery (>90%); low clean-coal ash (4-6% ash) and high pyrite rejection (70-80%).

Jan 1, 1994

By Allen V. Reicks

Modern conveyor pulleys are welded steel structures subjected to dynamic loads. In this paper, fatigue notch and fracture mechanics methods are applied to several weld joints on typical pulley constructions. These methods are used to analyze field applications and are correlated with laboratory testing. Generalized approaches are presented which provide high confidence in pulley design with corresponding high reliability.

Jan 1, 1996

By G. Schubert, H. Hoberg

A large number of diverse size reduction machines is currently available for the comminution of waste materials. Equipment selection is determined by the nature of the material to be treated and by its behavior under external mechanical stressing. Accordingly, wastes can be divided into those with elastictbrittle and those with ductile/viscous behavior. The scientific understanding of the comminution of wastes is lagging strongly as compared to that of the grain-shaped mineral raw materials. Only in a few unique cases have the fundamentals of the comminution of ductile or viscous materials been presented. The paper centers on a characterization and systematic analysis of the types of stress fundamental to comminution. On the basis of this discussion an overview is presented of the currently available technologies for the comminution of wastes, with attention centering on those machines designed for materials with ductile or viscous behavior.

Jan 1, 1998

By D. Robert Weir, M. J. H. Ruscoe, R. M. Berezowsky, M. A. Clegg

The metallurgical processing involved in the produc-tion of the new Canadian one dollar coin is reviewed starting with the hydrometallurgical production of pure nickel powder, followed by the powder metallurgy process for the production of nickel strip and coinage blanks, and concluding with the Aureate bronze electroplating and heat treatment procedure. Coinage requirements are then reviewed with regard to economic, public acceptance, and service requirements. Finally the properties of Aureate nickel coinage are presented in the light of the many and varied coinage requirements, and it is concluded that the new Canadian dollar coin exceeds the requirements admirably.

Jan 1, 1990

By Thomas M. Tharp, Mark A. Travers

A new method is presented for precracking three-point bending specimens for fracture toughness testing. A notched specimen of rectangular cross section is placed on a flat loading platen, with paper between specimen and platen. The specimen is loaded from above through a roller placed directly over the crack. The thin, high compliance joint between specimen and platen causes a distributed load on the bottom of the specimen. This results in bending at the cracked section and crack initiation at the notch tip. Since the joint is thin, its stiffness increases rapidly with deflection and crack propagation in the specimen generally remains stable and controllable. Fracture toughness KIC in a sandstone directly overlying the No. V coal was measured to be 0.27 MPa m 1/2. Even for cracks 1 cm long this value of KIC results in substantially lower effective tensile strength (modulus of rupture) in roof beams than is expected from intact rock strength.

Jan 1, 1986

By S. K. Kawatra, Harrison R. Cooper

In the last 30 years, on-¬stream slurry analyzers have proven to be of great use in the control of mineral processing circuits. This review discusses the two most popular methods, x-ray fluorescence and neutron activation analysis, and also considers techniques which are still under development.

Jan 1, 1986

By B. Mishra, Q. Shi, Y. Zhao, G. Zhao

Shale is anisotropic due to the presence of bedding planes. The anisotropic strength of shale has been extensively studied. However, little attention has been paid to the size effect on shale strength considering the anisotropy. This research uses the discrete element method to study the size effect on the strength of shale under the uniaxial stress state. It is assumed that the anisotropy is caused by bedding planes, while the size effect is caused by randomly distributed flaws. The numerical model of shale comprises three components: shale matrix modeled by bonded particles (2) bedding planes modeled by smooth joints (3) flaws modeled by discrete fractures. The developed model is scaled to different sizes and tested in the uniaxial compression and the direct tension tests. The test result show that the uniaxial compressive strength decreases as the specimen size increases when the loading direction is perpendicular or parallel to bedding planes. The uniaxial compressive strength is determined by the flaws while the bedding planes only play a limited role. However, the size effect on the direct tensile strength depends on the direction of bedding planes. When the loading is perpendicular to bedding planes, the size effect is not prominent. The direct tensile strength is determined by the bedding planes while the flaws have little effect. When the loading direction is parallel to bedding planes, the direct tensile strength decreases when the specimen size increases. The direct tensile strength is determined by the flaws while the bedding planes have little effect.

Mar 2, 2022

By PAITIP THIRAVETYAN, KANJANA KUDPENG

The aim of this study was to investigate the influence of amino acids (glycine, aspartic acid, glutamic acid, lysine and tryptophan) and organic acids (citric, malic, tartaric, fumaric, oxalic, succinic and ascorbic acid) on gold extraction from silicate ore. Use of amino acids to extract gold was preferred compared with organic acids due to the presence of carboxylic group and amine groups in amino acids. Among the assessed amino acids, aspartic acid and glutamic acid had higher capacities to extract gold due to their structures, which lacked aromatic rings and long side chains. Organic acids could also extract gold. In particular, oxalic and succinic acids had the greatest capacity to extract gold versus the other tested organic acids. Moreover, aspartic acid had a greater capacity to extract gold from ores than the same concentration of succinic acid. We confirmed the aspartic acid and succinic acid functional groups by Fourier transform infrared spectroscopy. The findings revealed that aspartic acid had a greater capacity to extract gold than succinic acid due to the presence of both amine and carboxylic groups (succinic acid contained only a carboxylic group). The optimal gold:aspartic acid molar ratio was 1:6 and low concentrations of aspartic acid extracted 35–42%of gold from silicate ore within 15 days. This can be used as an alternative to traditional methods for extracting gold from ore; it is non-toxic to human health and environmentally friendly.

Aug 10, 2021

By C. Cristoffanini

A real-time transient pipeline simulation was used to model the operational pressure response in the concentrate and tailings pipelines of the Minera Los Pelambres copper mine in Chile. A high-fidelity simulator was needed to train the operators on safe operation of the pipeline for different scenarios. A simulator that solves the transient equations was used to dynamically predict the pressure and flow throughout the pipeline to provide real-time responses to operational changes such as opening or closing a choke valve, or sending a water batch. Slurry rheological properties were incorporated into the model. This paper presents the technical background of the pipeline simulation model and the study of slurry properties. The paper shows the results of the transient simulation for different operating scenarios such as start-up, shutdown and leakage, by presenting the hydraulic gradient curves for each case. Finally, the paper briefly presents how the simulator was connected to an emulated control system and used to train the operator, it demonstrates the most effective tool available to learn to resolve undesirable conditions.

Feb 23, 2014

By D. Constantinides

In 1981 a Zn-Ag-Pb deposit was discovered in the vicinity of Molai, Greece. Subsequently, it was determined to be of the Kuroko type. The geology of various areas in the southeast Peloponnesean Peninsula is similar to that of the Molai deposit. Since favorable geologic criteria are present, absent, or unknown in varying degrees in all areas, it was deemed necessary to classify and rank the prospective areas according to the level of information available. For each level of information, an ore discovery model based on pragmatic exploration criteria was developed, enabling the favorability of occurrence to be calculated for each area. A Monte Carlo simulation was used to calculate the probabilities, the input data consisting of quantitative and qualitative estimates of the geologic criteria for each area. Three levels of information were modeled : Level A consisted of 9 criteria, level B of 12 criteria, and level C of 20 criteria. The three levels of information were tested on the Molai area. The results exceeded expectations, showing the gen¬eral trends which control mineralization at the lowest level of information. With an increase in the level of information, geological trends become more evident and a differentiation can be made between areas containing Cu mineralization, exhibiting a low probability, and areas likely to contain Zn-Ag-Pb mineralization. The models were then applied to the neighboring areas - only level A and B were available.

Jan 1, 1986

By Maurice C. Fuerstenau

INTRODUCTION The term, chelate, from the Greek for 'claw,' has its origin in the pincer-like representation of more than one atom of a single ligand bonded to the same metal atom, forming a ring-like structure. Depending on how many attachments exist on the sphere of coordination around the metal ion, ligands are referred to as bidentate, tridentate, tetradentate, pentadentate and hexadentate According to Calvin and Martell (1952) and Somasundaran and Nagaraj (1984), chelating agents must contain suitable functional groups, and their location within the ligand molecule must enable ring formation that is sterically possible. Typical structures that meet these requirements have been given by Fuerstenau and Herrera-Urbina (1988) and are listed in Figure 1. As noted, the functional groups of these reagents contain electron donor atoms such as oxygen, nitrogen and sulfur. Basic groups, such as amino (-NH,), are those that contain an atom with a lone pair of electrons. Acid groups are those, such as carboxylic (-COOH) which lose a hydrogen ion and coordinate with the metal atom. Examples of each of these types chelating reagents are given in Tables 1-4. The specificity of chelating agents for various metal ions has long been known and was utilized early in the search for new flotation collectors. In 1927, Vivian used ammonium nitrosophenylhydroxylamine as a collector for cassiterite. Holman (1929) tested dimethylglyoxime as a collector for nickel oxide. He also suggested taurin as a collector for oxidized lead ores. DeWitt and von Batchelder (1939) suggested the use of oximes as flotation collectors. Gutzeit (1946) conducted an extensive investigation on the use of chelating agents as collectors and as depressants for gangue minerals. The depressants are those reagents that form soluble chelates with metal ions that could function as

Jan 1, 2005

By Jerry Motz, Gary Beerkircher

Through a joint development program between Bougainville Copper Ltd. and Nordberg, the MP1000 cone crusher was developed and tested during the period between 1982 and 1987. Following the successful prototype work, Bougainville Copper purchased an additional three units. A second prototype was installed at Codelco's El Teniente three-stage crushing installation in 1987. This unit has also completed its test period successfully. Three additional units have been sold, making a total of eight, to date. Two will be installed as secondary crushers in two separate large aggregate plants. The first unit installed in the United States was placed in operation at Vulcan Materials Company's plant in Manassas, Virginia in early May 1990. Another unit is being installed in Asarco's Ray Mines expansion. The Asarco installation will be a SAG MILL pebble crusher producing approximately 600 STPH of nominal 1/2" product. Application Objective The objective was to design a crusher that would fit on an existing 7' foundation with minimum modification and yet be capable of twice the production of a 7' cone crusher. In meeting this objective, the power rating was increased to 1000 HP, the maximum design crushing force was increased and the crusher was designed to operate at higher speeds than an equivalent size Symons cone crusher. The MP1000 was also designed to operate with a head throw that can be greater than the equivalent Symons design. Design The crusher design criteria involved the recognition of the crushing force increase required for the finer crushed products than

Jan 1, 1992