Search Documents

By T. Lindstad, J. Kaczorowski

The Boudouard reactivity of single cokes produced from selected bituminous coals and commercial cokes has been investigated in a thermo gravimetric furnace. The effect of potassium as a catalyst for this reaction was studied, as it is known to accumulate in ferromanganese furnaces. A gaseous impregnation technique using K2CO3 as the potassium source was applied to impregnate the coke samples. The reactivity experiments were designed to simulate conditions occurring in an industrial furnace, as used for production of Mn-alloys. The coke particle size varied from 3.35 to 6.63 mm, while the temperature was maintained between 800- 1100oC with a gas composition from 50 to 75% CO2 in a CO/CO2 mixture. To determine the catalytic effect of potassium, the concentration varied from a fraction of a percent up to 15%wt. The results show that single chars vary significantly in reactivity, depending on the properties of the parent coal, while commercial cokes exhibit similar reaction rates. Temperature and partial pressure of CO2 have the strongest influence on the reactivity, while the influence of gas flow rate and coke particle size were found to be negligible. The catalytic studies revealed that the relative reactivity of non-impregnated samples are preserved after the impregnation, so the least reactive coke is still the least reactive after the impregnation for the whole range of potassium loads. Also, it has been confirmed that the Boudouard reactivity reaches a plateau at potassium concentration of 4%wt.

Jan 1, 2007

By W. P. Channon, J. B. See

The reduction of fluxed and non-fluxed manganese, ores by ferromanganese silicide by W. P. CHANNON, B.Se. (Eng.), M.Sce. (Eng.) Wits. (Visitor) and J. B. SEE, B.Sce. Hons., Ph.D. (New South Wales), M.I.M., M.I.M.M. (Member) In South Africa, medium-carbonferromanganese is produced by the silicothermic reduction of slags containing MnO. Because of its importance in the production of refined ferromanganese, a study was made of the reaction between a premelted South African Mamatwan manganese ore and various ferromanganese silicide reducing alloys, with and without fluxing agents. Because the reaction is highly exothermic, temperature appeared to have little effect on the rates of manganese transfer to the metal and silicon transfer to the slag, and an apparent equilibrium was rapidly approached. Limits were determined for the favourable effects of fluxing additions, and manganese recoveries were found to decline as the ratio of CaO to MgO decreased as a result of the addition of basic flux. The recovery of manganese passed through a maximum, and subsequently decreased for variations in the ratio of alloy to ore. The results obtained, when used in conjunction with other physicochemical data related to this slag-metal system, suggest optimum slag compositions for the efficient manufacture of medium-carbon ferromanganese from Mamatwan ore.

Jan 3, 1977

After the closure of collieries, they naturally start to fill up with water. As a result, hydraulic gradients develop between them and different hydraulic pressures are exerted onto peripheral areas or compartments within mines. This results in water flow between mines, or onto the surface. This flow is referred to as intermine flow. The collieries in the Witbank Coalfield have geometries such that there are several areas where this intermine flow is possible. Since the Department of Water Affairs and Forestry has declared intermine flow as one of its greatest concerns for granting closure to South African mines, much research into this phenomenon is required. The challenges in determining intermine flow are numerous, and attention has focused on identification of areas where these flows can take place. The quantification of these flows is problematic due to the uncertainties in exact geometric configurations and the variation in site-specific hydraulic properties of thecoal and overlying lithilogical layers. During this study, use has been made of numerical flow modelling and several analytic solutions to test the applicability of the flow models as well as to predict groundwater flow directions, filling times of voids and flow volumes. The numerical modelling methodology entailed a downscaling approach starting with a broad regional model covering the entire area, followed by modelling the interactions between interconnected mines, and finally looking in detail at the major areas of interaction.

Jan 1, 2005

By Y. Mao, D. Xie

The viscosity of TiO2-containing blast furnace slags may increase rapidly (commonly referred to as thickening) under strong reducing conditions in the blast furnace. To elucidate the mechanisms for slag thickening, measurements have been made of changes in the composition and rheological properties of TiO2-CaO-SiO2-Al2O3-MgO slags during the reduction process. The slag composition covered the range of 17–33 wt% TiO2, 9–19% Al2O3, 8–16% MgO and theCaO/SiO2from 0.8 to 1.4. The viscosities were measured using the rotating cylinder method at temperatures up to 1550ºC and the fusibility temperatures were determined from ‘breaks’ in the viscosity-temperature curves. The reduction of the slag was carried out in graphite crucibles at1500ºC for 2–6 hours The rheological properties of the slags during reduction were predominantly influenced by the slag basicity (CaO/SiO2), and the effect of other components depended largely on basic or acidic behaviour of the oxide. The reduction of TiO2in the slag by carbon was initially fast to formTi2O3, followed by further reduction to TiO and TiC. Correspondingly, the viscosity showed initially a slight decrease, followed by a gradual and then rapid increase. The thickening was found to be accelerated by an increase in TiO2content and a decrease in the CaO/SiO2in the slag. In addition to the existence of 1~3 wt% TiC, the thickened slags also had a significant amount of TiO (3~7 wt%), suggesting that TiO may play an important role in the ‘thickening phenomena’ ,possibly by forming solid solutions with TiC to significantly increase the number of solid particles in the heterogeneous slag. Keywords: TiO2slags, viscosity

Jan 1, 2004

By S. Pal, A. K. Lahiri

Most of the compounds present in slag are surface active. This gives rise to foaminess of slag. The foam life and foaming index are normally determined by the draining rate of slag through the plateau border, so the foaming index is directly proportional to slag viscosity and inversely proportional to slag density and bubble diameter. When a small amount of a strong surface active compound like P2O5or Cr2O3is present in slag, however, the foam life increases significantly and the above relationship is not obeyed. The strong surface active compounds reduce the draining rate from the film between the adjacent bubbles so the film draining controls the life of the foam. The thickness of the film, Marangoni force, viscosity of the slag, and diffusion of surface active compounds determine the film draining rate. The interplay of these factors leads to very low or high film draining rates and affects the film and foam stability significantly. Keywords: slag, foam, foaming index, film draining

Jan 1, 2004

By A. V. Pavlov, A. V. Dubachev, K. L. Kossyrev

The purpose of the given research was to investigate the possibility of high-carbon ferrochromium refining to remove harmful impurities as a result of metal treatment by slag mixtures on the basis of the CaO-MgO-SiO2system. The final conclusions were drawn from experimental results. It was shown that the treatment of high-carbon ferrochromium by SiO2-MgO-CaO slag mixtures with additions of chromium sinter or iron-ore concentrate removes carbon, sulphur and phosphorus from the metal. A mechanism of phosphorus removal from a melt to a gas phase is proposed.

Jan 1, 2004

By J. P. Harrison, J. A. Hudson

ABSTRACT: Given the current widespread use of numerical models for rock mechanics and rock engineering, and the ‘Technology Road Map’ theme of the Congress, it is timely to consider the key issues in matching numerical models to rock engineering problems. The three main aspects are: a) identifying the mechanisms, variables and parameters that are relevant to a particular rock engineering project; b) establishing the content and mode of operation of a particular code; and c) deciding whether a particular code provides an adequate model for a particular project. We summarise the key issues, highlighting the concept of rock mass domains, validation and the ability to present the results of a modelling exercise. We include three compact numerical modelling case examples to illustrate the points. Finally, we also present a ‘roadmap’ to assist in the process of matching a numerical model to the rock reality. RESUME: Considérant l’utilisation généralisée des modèles numériques en mécanique des roches et en ingénierie au rocher ainsi que le thème du congrès ‘technology road map’, il est opportun d’aborder les problèmes essentiels liés au choix des modèles numériques dans les problèmes ingénierie au rocher. Les trois aspects principaux sont : a) l’identification des mécanismes, variables et paramètres appropriés au projet considéré, b) la définition du contenu et du mode de fonctionnement d’un code numérique donné, et c) la possibilité de décider si un code donné fourni un modèle approprié au projet considéré. Les points clés sont résumés en mettant en évidence les notions de “massif rocheux”, de validation et de capacité à présenter les résultats d’une approche numérique. Nous présentons trois brèves études de cas qui illustrent ces points. Enfin, nous proposons aussi un logigramme pour aider au choix d’un modèle numérique approprié pour représenter la réalité d’un problème au rocher. ZUSAMMENFASSUNG: Im Licht der augenblicklich weitverbreiteten Nutzung von numerischen Modellen in der Felsmechanik and im Felsingenieurbau und unter Beruecksichtigung der Themenstellung des Congresses “Technology Road Map”, erscheint es an der Zeit die Kernprobleme, die sich mit Fragen der Abstimmung der numerischen Modele mit Hinblick auf ihre Anwendbarkeit im Felsingenieurbau beschaeftigen, naeher zu befassen. Die drei wesentlichen Aspekte sind: a) Identifizierung der Mechanismen, Variablen und Parameter, die fuer ein bestimmtes Projekt im Felsingenieurbau von Bedeutung sind; b) die Festlegung des Inhalts und des Modus Operandi eines bestimmten Codes, und c) die Entscheidung darueber ob ein bestimmter Code ein hinreichendes Model fuer ein bestimmtes Projekt ergibt. Wir fassen die wichtigsten Punkte zusammen, heben dabei das Concept der Gesteinsmassen Domaenen (Rock mass domains) hervor, und erarbeiten ihre Beurteilung und die Moeglichkeit diese zu praesentieren in den Ergebnissen einer Model Uebung. Wir schliessen drei Beispiele von numerischen Modellen ein in denen diese Punkte erlauetert werden. Zuletzt schlagen wir eine “Roadmap” vor, um dem Prozess der Abstimmung des numerischen Modells mit der “Felsmechanischen Wirklichkeit” zu unterstuetzen.

Jan 1, 2003

By A. V. Pavlov, V. A. Grygorian, Kossyrev, A. E. Semin, A. Korostylev

A new way of producing low-silicon ferrosilicon from iron-ore materials in a new type of aggregate-oxygen reactor is presented. The oxygen reactor process is based on using the calorific combustibility and reducibility of carbon materials inside the aggregate. The key to the process is successful post-combustion of carbon monoxide above a layer of a solid coke bed. Initially the possibility of production of grades of ferrosilicon containing 20 to 25% Si (FeSi20-FeSi25) was studied on a laboratory model of the oxygen reactor. Quartz sand and iron ore concentrates (from Russia and India) were used in the laboratory tests. This test work demonstrated that a ferrosilicon grade FeSi15 could be obtained directly from raw iron ore (containing 75.9 % Fe2O3 and a maximum of 23.8 % SiO2) without using rich iron-ore concentrates. The process was successfully tested on a pilot furnace at Serovsky metallurgical plant. Very promising results and efficiency parameters were achieved. The consumption of materials for 1t of ferrosilicon (15 % Si) production was as follows: 1567 kg raw iron ore, 591 kg of coal (in a composition of ore-coal briquettes), 299 kg of coke (for coke bed formation), and 815 m3 of oxygen.

Jan 1, 2004

By K. Saito, Y. Miyauchi, T. Nishi, Y. Kizu

At Tokushima Plant of Nippon Denko Co., Ltd. high-carbon ferromanganese is produced by the electric furnace method using lump manganese ores and sintered manganese ores manufactured from fine manganese ores. However, the distribution of manganese ores is significantly uneven on earth, and their characteristics considerably vary by ore type. It is known from experience that the production of high-carbon ferromanganese by the electric furnace method depends greatly on material ores. Therefore, to maintain stable operation in the electric furnace-smelting field, it is important to identify the characteristics of each type of material ores in advance. Thus, we evaluated the high-temperature electric characteristics of manganese ores using the electrical conductivity measuring system developed by ourselves and provided the standards for determining ores and blending ratio necessary for stable operation of the electric furnace based on the evaluation results. This time we worked for optimisation of the high-temperature electric characteristics of sintered manganese ores through modification of the characteristics because the blending ratio of sintered manganese ores in the electric furnace is high. The electrical conductivity of sintered ores having various chemical components in a high-temperature region (up to 1 550°C) was measured using our electrical conductivity measuring system and high-temperature electric characteristics evaluating method reported at INFACON 9. As the result of the measurement, we revealed that the high-temperature electric characteristics of the sintered ores depend on their chemical contents and the sintered ores can be modified to those having excellent high-temperature electric characteristics by controlling their chemical contents, so that the resources can be effectively used.

Jan 1, 2004

By Darelle T. Janse van Rensburg

Some of the more recent developments in Paint Technology are solvent free materials. These coatings have mainly been formulated to overcome the negative attributes of solvent-based coatings, i.e. environmental, safety and health risks, potential for solvent entrapment and osmotic blistering, as well as the formation of micro-pores during the curing process. Two solvent free liquid epoxy coatings have been used extensively on power generation plant. However, very little is known regarding their long-term performance under different exposure conditions, as well as whether these coatings actually perform better than their solvent-borne counterparts. In addition, solvent free materials are generally used where outage periods are restricted and coatings need to be applied within a very short period. Though these materials have reportedly much shorter curing times than other conventional solvent-borne coatings, little is known regarding their limits with respect to maximum film thicknesses and being put into service while still being wet/partially uncured. The latter has become common practice at many power stations in the past two years or so. In addition, the application and curing methods of solvent free materials are different to that of solvent-borne materials, and may require equipment and application process changes. This paper covers the application and performance properties of solvent free coatings in comparison to solvent-borne materials primarily intended for immersion service. Numerous coatings were evaluated under immersed static and cyclic hydrostatic pressures. Other tests included short curing / early immersion tests, dry-to-touch and dry-through curing times, adhesion tests, surface tolerance tests, etc. The results show that the solvent free materials have clear benefits with respect to safety, health, environmental and long-term performance, but will be more difficult to apply compared to solvent-borne materials.

Jan 1, 2006

By W. Bryszewski

As a result of strategic analysis in respect of the needs for air quality management a new advanced and holistic approach to air quality management process was introduced in the North West Province (NWP) of South Africa. The process is based on the principle of co-operative management. It involves both active participation of all Interested and Affected Parties (I&AP) and the holistic approach to solving problems with the underlying principles of shared ownership and sustainable development. The process consists of the followings phases: ? Industrial process quantification ? Quantification of impacts ? Formulation of the required control measures ? Definitions of certificate conditions ? Implementation of an adequate compliance management system at company level ? Ongoing co-operative air quality and system management with the strategic objective of continuous improvements The system has been successfully introduced in the North Province and proved to be an effective management tool and aids assurance of sustained environmental ability to cope with the pressure of industrial developments. The benefits and effectiveness are discussed using Hernic Ferrochrome as an example. Hernic Ferrochrome is one of the first companies, which successfully implemented this system.

Jan 1, 2004

By J. Kuijpers

Failure and fracturing are often regarded as synonymous. While this is obviously true in an environment dominated by tensile stresses, it is still not clear how failure and macro fracturing are related in a compressive stress environment. Excavations at great depths are typically subjected to compressive stresses only. The fracturing observed around such excavations is therefore commonly assumed to be induced by such compressive stresses. The physics of such a phenomenon have unfortunately never been explained properly, so that the formation of these so-called extension fractures still remains a mystery. As the presence of fractures is an important factor affecting the stability of underground excavations, it is of practical relevance to understand their formation. In this paper, a possible explanation is proposed. It is argued that fracturing in a compressive stress environment is a secondary effect. Primary failure, in the form of micro fracturing and associated damage is assumed to precede the major fracture processes. The fractures are thus generated in response to material failure and may not directly be the cause of failure. The implications for material response and behaviour are discussed. Keywords: micro fracturing, macro fracturing, extension fractures, failure, compressive stresses, damage, excavations.

Jan 1, 2000

By I. McDougall

The matte/slag tidal zone in a nickel-copper-iron-sulphide matte smelting furnace is subject to severe process conditions that can lead to premature failure of the lining. The MgO-FeO-SiO2 slag is aggressive to refractory bricks, while the Ni-Cu-Fe-S matte is aggressive to water-cooled copper cooling elements, and can penetrate and sulphidize refractory bricks. A novel approach to the lining design was taken at a PGM smelting furnace, where an indirectly-cooled graphite ring was applied in the matte/slag tidal zone, with refractory bricks on the hot face. The graphite was cooled by the copper cooling elements in the slag zone, obviating the need for copper cooling elements in the tidal zone. In this paper the effectiveness of different lining designs utilizing varying degrees of cooling in the slag zone and slag/matte tidal zones is compared. In comparison to water-cooled copper in various configurations, cooled graphite shows promise as an indirect refractory cooling system in the tidal zone area of furnaces. Keywords PGM smelting, graphite, refractory lining, copper cooling elements, submerged arc furnace.

Aug 1, 2013

Threshold blasting involves the use of small amounts of high explosive to break and fragment hard rock without having to evacuate mining personnel. The method is easily assimilated and effective in rockbreaking, but requires rigid control on drilling, charging and timing. Current underground trials are aimed at fine-tuning the amount of explosive energy and blast hole geometry to allow the firing of multiple sets of shot holes in a continuous manner. Through correct procedures, the after-blast fumes, dust and fly rock can be contained so as to provide a safe working environment. Threshold blasting hugely reduces the volumes of explosives used in mining and brings to maturity the potential of the process begun by Alfred Nobel when he introduced nitroglycerine, and later dynamite, to mining. Its key contribution is its enabling of continuous mining operations with well understood and relatively low cost technologies. The use of batch blasting, employing large burdens holds the greatest potential for delivering high flow rates of ore at minimal cost. There is good potential for rapid evolution of the concept.

Jan 1, 2002

By N. R. Williams

Black Mountain, a polymetallic base metal mine located in the Northern Cape territory of South Africa has been blessed with high grade economic ore for many years. Now that the Broken Hill orebody is nearing the end of its life, a lower grade orebody (Swartberg) is being exploited to supplement production from Broken Hill. In addition, ore from stopes in the upper levels of the Broken Hill orebody is considerably tarnished (oxidized). As a natural result, the remaining ore contains a higher percentage of magnetite, pyrrhotite and pyrite than in earlier years. Bismuth, cadmium and cobalt also occur in the ore in higher quantities. The life of the mine has been lengthened with the discovery of further deeper-lying ore reserves extending from the Broken Hill orebody suitably called the Deeps section. However, to bridge the gap between development of the new reserve and the exhaustion of the old reserve, these lower grade and tarnished (oxidized) ores have to be treated. The mine has had reasonable success in identifying unfavourable or problematic ore types and stockpiling them separately to blend in small quantities with more favourable ore. Bench and plant scale tests have aided identification of the various ore types and significant improvements in flotation metallurgical results have been seen. Copper, lead and zinc metal occur as sulphides in the ore. The mill consists of a differential and sequential flotation process that extracts copper concentrate, lead concentrate and zinc concentrate respectively with silver metal recovered in the copper and lead concentrates. This paper describes the ore blending strategy employed at the mine to maximize the econo-metallurgical efficiency of the operation.

Jan 1, 2001

By David Norval

The increased tendency to use hydrometallurgy as an extraction step towards final refining following a pyrometallurgical smelting process requires melts which have to be cast and or comminuted which can then be taken up into solution or leached. To generate surface area for optimal leaching, a common process is to granulate and in many cases mill, which is a general practice with friable material with properties associated with higher sulphur, carbon and silicon levels. However, in the case of metallic melts milling can be unfeasible due to the ductility of the granulated particles. Water solidification is capable of producing either fine particles by means of granulation or atomisation. Atomisation however, can produce particles as fine as 40 microns without a milling circuit.

Jan 1, 2005

As part of a comprehensive risk analysis which was carried out into the effectiveness of the water barrier between South Deep and Randfontein Estate mines, the potential threat posed by large seismic events was assessed. The study covered several aspects. Firstly, an estimate of the maximum credible earthquake was obtained from a probabilistic analysis of the regional seismicity of the previous 25 years. Allowance was made for ?reservoir-induced? effects by increasing the estimate of the size of the maximum credible earthquake from ML= 5.1 to ML= 5.5. Based on available knowledge of the geological structure, the possibility of such an event occurring in the vicinity of the barrier pillar was estimated. The possibility of substantial damage to the barrier rock mass, resulting as a consequence of a large event, was assessed. The likely damage to the concrete control plugs installed in five tunnels that penetrated the barrier, which might result from a ?near-miss? by the largest possible seismic event or from a ?direct hit? by a smaller event, was also considered. It was concluded that there was a negligibly small possibility that the maximum credible earthquake could occur close enough to the barrier, and in such a manner, as to cause any damage to it or to the plugs in the tunnels passing through it. The possibility of serious plug damage occurring as a result of a ?direct hit? by as maller event was slightly greater, but still sufficiently remote as to be of no practical concern at all.

Jan 1, 2006

By T. J. Kolokoto

This paper is based on a project conducted at Khomanani 2 shaft, Anglo American Platinum Limited. The main objective was to find an alternative support element in stopes to address the falls of ground (FOG) problem experienced at this shaft. Literature review was the major method used in the investigations. Resin bolts or any 1.5 m in-stope roofbolts were considered. The shaft was making use of 0.9 m long friction bolts, and these could not prevent the FOG experienced. Observations indicated that the FOG resulted in fall-out thicknesses averaging to 1.1 m, which is greater than the supported length of the friction bolts. The implementation of 1.5 m long bolts was recommended as a result of the project. These bolts will be able to address the fall-out thickness and provide sufficient support resistance to mitigate FOG. The chosen support element will result in a relatively small increase in support costs.

Jan 1, 2013

By H. Willenberg, J. S. Coggan

ABSTRACT: Although individually both continuum and discontinuum numerical analyses provide useful means to analyze rock slope stability problems, complex failures typically involve mechanisms related to both existing discontinuities (i.e. discontinuum) and deformation and brittle fracture of intact rock (i.e. continuum). One such example is the 1991 Randa rockslide in the southwestern Swiss Alps, where failure involved several complex mechanisms, which require the consideration of progressive failure and rock mass strength degradation. This paper presents results from a series of hybrid finite-/discrete-element models directed towards the explicit modelling of brittle fracturing in natural rock slopes, enabling the modelling of progressive failure, from initiation, through to the development of catastrophic failure, transport and deposition. RÉSUMÉ: Si les modélisations numériques de type continu ou discontinu fournissent des outils utiles pour l’analyse de problèmes de stabilité de pentes rocheuses, elles montrent de sérieuses limitations lorsque des mécanismes de rupture complexes impliquent des processus liés autant aux discontinuités préexistantes qu’au développement progressif de nouvelles fractures. Ceci se retrouve typiquement dans l’exemple de l’éboulement de 1991 à Randa dans les Alpes suisses du sud-ouest, où la rupture a impliqué plusieurs mécanismes complexes nécessitant la prise en considération de la fracturation progressive ainsi que de la dégradation de la résistance des masses rocheuses. Cet article présente des résultats provisoires d'une série de modèles hybrides orientés vers la modélisation explicite de la fracturation de pentes naturelles, permettant la modélisation de fractures progressive de leur initiation jusqu’à leur développement, leur rupture catastrophique, leur transport et leur déposition. ZUSAMMENFASSUNG: Obwohl numerische Kontinuum- und Diskontinuum-Berechnungen einzeln nützliche Ergebnisse zur Stabilitätsanalyse von Felshängen liefern, sind komplexe Felsrutschungen typischerweise mit Mechanismen verbunden, die sowohl durch bestehende Trennflächen (s.a. Diskontinuum-Ansatz) als auch durch die Deformation und das Versagen intakter Felsbereiche (s.a. Kontinuum-Ansatz) bedingt werden. Ein Beispiel für einen solchen Sachverhalt ist der Bergsturz von Randa 1991 im südwestlichen Teil der Schweizer Alpen, bei dem die Rutschung mehrere komplexe Mechanismen umfasste, so dass “progressive failure” und Verminderung der Gebirgsfestigkeit in Betracht gezogen werden müssen. Dieser Artikel beschreibt vorläufige Ergebnisse einer Reihe von hybriden Modellrechnungen (Finite-/Diskrete-Elemente). Diese haben zum Ziel, explizit das bruchhafte Versagen natürlicher Felshänge zu modellieren, wobei das progressives Versagen im ganzen modelliert wird, von der Anfangsphase über die Entwicklung zum katastrophalen Versagen und den Transport und die Ablagerung der Rutschmassen.

Jan 1, 2003

By C. Maree

Paper written on project work carried out in partial fulfilment of B. Eng (Chem. Eng.) This paper describes the development and use of a process simulator to optimize gypsum recovery at Afmine, a small plant near Yzerfontein on the South African West Coast. The simulator consisted of models of the major plant equipment, viz. hydrocyclones, surge bins, settling tanks, a primary sieve and a dewatering screen. Experimental data suggested that the equipment could be modelled satisfactorily from data published in the open literature. Simulation studies have indicated that gypsum losses on the plant could be reduced substantially by means of some relatively minor modifications to the plant layout. Moreover, sensitivity analyses of the plant have indicated that optimization of the settling tanks should receive priority over the other process units.

Jan 1, 2005