Search Documents

By M. Rudolph, J. Sygusch

Froth flotation is well-established and efficient in the selective separation of valuable particles from unwanted material with sizes ranging from 10 μm to 200 μm. However, when it comes to the separation of ultrafine particles (< 10 μm) there are still some challenges, or rather opportunities. This research aims at developing a method for the separation of ultrafine particles based on multiple particle properties. Amongst such properties are wettability, morphology (shape or roughness) and size with applications not only in mineral processing but in general chemical engineering. In this study, three differently shaped fractions are used as valuables for testing: spherical particles, elongated particles and irregularly shaped particle fragments; together with ultrafine magnetite as the gangue material, in order to investigate the effect of particle morphology on ultrafine particle flotation, as well as wettability, which is varied by esterification using alcohols. Flotation tests are carried out using a novel flotation device that was designed especially for the flotation of ultrafine particles, combining advantages from machine-type froth flotation and column flotation. The results showed that, in contrast to previous studies, recoveries for ultrafine spheres were higher than for ultrafine fragments for all wettability conditions, and hydrophobisation generally increased particle recoveries for said morphologies. Tests using fibres showed different behaviour as hydrophobisation had negative effects on their recovery, despite increased selectivities and kinetics. These findings suggest that apart from influences of particle properties within the suspension zone, their effects on the froth characteristics should be studied in more depth. Keywords: Ultrafine particles, Flotation, Particle shape, Wettability, Esterification of glass, Hydrophobisation

Jan 1, 2020

By G. Mahieu, L. Perez-Barnuevo, P. Barbeau-Verreault, O. Gravel

Raglan mine is a copper-nickel mining operation, part of Glencore, and located at the northern border of the province of Quebec, in Canada. The concentrator is fed by a mix of four different underground mines, thus it must accommodate periodic variations in run-of-mine mineralisation and composition. In order to concentrate nickel and copper sulphides, the flotation circuit also includes a regrind step at the cleaner stage. This leads to challenges in maintaining optimal recoveries and in diagnosing potential disturbances. This paper advocates for the combination of automated mineralogical analyses, reconciliated mass balances from diagnostic sampling campaigns and innovative multidimensional visualisation to assist in tackling these challenges. Through this approach, it has been possible to quantify the regrind step influence on the liberation of valuable mineral particles in the final flotation concentrate. The methodology also allows for virtual sieving of the products in order to track unit loss in the flotation process. The proposed analysis scheme presents an opportunity to easily diagnose flotation circuit performance based on mineralogical information. Keywords: Flotation diagnostics, multi-dimensional visualisation, mineral liberation analysis

Jan 1, 2020

By E. Cetin

Orebodies that contain more than one economically important mineral are generally evaluated by parametric cut-off grades. This approach often leads to mis-valuation of mineral deposits because cut-off grades are not based on the grades of each individual mineral and, because of the parametric formulation, are only indirectly related to the individual grade distributions. The only realistic approach is a formulation that accounts separately for each component mineral. The grid search method can be used as a means of multi-mineral cut-off grade optimization in this context. This paper describes the use of the grid search method in cut-off grade optimization for multi-mineral deposits. The authors introduce the general concepts of the method and formulate its application to cut-off grade optimization; they describe a software implementation of the method that can accommodate cut-off grade optimization for mineral deposits that contain up to three economic minerals. Keywords cut-off grade, optimization, grid search, multi-mineral deposits.

Aug 1, 2013

By M. Rossouw

The paper sets out the strategic importance of South Africa?s mining and minerals sector to the national economy. It relates how inexorable and accelerating urbanization and industrialization in emerging markets, especially in China and India, will translate into sustained demand for the minerals that South and southern Africa have in abundance. It warns that while countries buying raw materials from South Africa use these inputs as the basis on which to build value-added, employment-creating industries, South Africa is failing to exploit the economic benefits inherent in its mineral wealth, exacerbating its shortage of skills.

Jan 1, 2011

By J. O. Mogalanyane, N. Naudé, A. M. Garbers-Craig

The fines produced is not suitable as feed material for the subsequent rotary kiln and the electrical arc furnace. The need for briquetting the ferronickel ore is premised on the minimisation of fine particles in the rotary kiln as well as improving charge permeability in the furnace, and improving overall process safety. Briquetting may be defined as an agglomeration method in which fine particles are compressed under pressure. It consists of three different technologies: vibropressing, roller pressing and stiff extrusion. The current study focuses on evaluating the performance of ferronickel briquettes generated, using roller-pressing technology. Physical properties, chemical properties and metallurgical properties of the briquettes were used to evaluate their performance and quality. Standard ISO tests for iron ore pellets were used. Size degradation as a result of reduction was measured using the ISO 4696-1 test. The decrepitation of the briquettes at the point of entry into the rotary kiln was evaluated using the ISO 8371 test method at a temperature of 700oC. The degree of reduction was evaluated using the ISO 4695 test procedure. Average green briquette compressive strength of 559 N was reported at a moisture content of 16% with an average drop number of 19.1. Increasing the moisture content has a detrimental effect on both the compressive strength and the green briquette yield. The drop number is expressed as the number of drops until breakage, when a briquette is dropped from a 1 m height, decreased with an increase in moisture content. At a moisture content of 16% an average green briquette yield of 85.1% was reported. Keywords: Ferronickel briquettes, moisture content, curing conditions, physical properties, chemical properties

Jan 1, 2020

By E. L. Thyse, P. Bepswa

The Western Cape Mineral Processing Facility (WCMPF) is a collaborative educational initiative between the Department of Process Engineering at the University of Stellenbosch and the Chemical Engineering Departments at the University of Cape Town and the Cape Peninsula University of Technology. The primary objective of the WCMPF is to facilitate the education, development and graduation of suitably qualified engineering graduates and diplomats for the mining and mineral processing industries. In recent years the WCMPF has embarked on a number of initiatives aimed at improving the quality of mineral processing education which include, more importantly the introduction of novel ?end to end? or ?integrated? practicals. The practicals are developed around a specific mineral theme or route, which more than often includes the development of several new pilot plant practicals demonstrating key unit operations or processes in the selected mineral theme or route. The most recent mineral processing pilot plant practical programme is developed around the beneficiation of heavy mineral sands. The programme consist of the following developed pilotplant practicals: the online electrostatic separation of free flowing mineral sands using a Roche Mining Carrara high tension roll separator incorporating a Blue Cube Systems MQi in-line mineral quantifier; the production of titania-rich slag and pig iron from the smelting of ilmenite and anthracite in a 60 kW direct current (DC) plasma arc furnace as well as the mineralogical characterization of the feed and products; the continuous closed-circuit ball milling and screen classification of titania-rich slag. This paper illustrates the important role of a well-designed heavy mineral sands beneficiation pilot plant practical programme in facilitating the education and development of suitably qualified personnel for the mining and mineral process industries.

Jan 1, 2007

By R. Layton

Expert Systems Technology (EST) is becoming more and more widespread in both its range of applications and the public interest. It appears to be capable of performing tasks unmatched by other techniques. Within the mining industry a large body of unsolved problems now appear to have a solution. This paper examines the current state of EST both in the context of the history of Artificial Intelligence and current efforts at building mining expert systems. It provides recommendations for those wishing to get involved, and outlines the problems for those who believe that expert systems are capable of anything and everything. The paper also provides a detailed analysis of limitations of current EST that must direct research into more fundamental, commonsense areas than have been extensively covered before.

Jan 1, 1987

By S. W. Robertson, M. T. Golela, S. Mxinwa

South Africa has one of the largest Cr-related industries in the world and generates large amounts of Cr-containing smelter dusts. It is normal practice to scrub Cr from the furnace off-gas in water, and to recover the Cr by adsorption, followed by recycling of the loaded adsorbent into the furnace. A study was conducted to find a low-cost adsorbent that is capable of removing sufficient Cr from the solutions generated by scrubbing. The test work focused on the evaluation of different clay minerals (attapulgite, bentonite, and kaolinite) as adsorbents for Cr. Cr(VI) could only be adsorbed after prereduction with e.g. ascorbic acid (ASA). An 80% removal of Cr(VI) could be achieved from a solution containing 20 mg/L Cr using bentonite clay after reduction with ASA. Attapulgite and kaolinite adsorbed less than 55% Cr after reduction with ASA. Both ASA and ferrous salts were found to be suitable reducing agents. The use of acid mine drainage (AMD) was also investigated as a low-cost alternative reducing agent, as AMD usually contains iron. The Cr(VI) reduction potential of the AMD was determined by redox titration against a solution containing 50 mg/L Cr(VI). Studies show that AMD can potentially be used as a reducing agent in a Cr removal process if it is available on site.

Feb 12, 2024

By C. -J. Rick

The ferroalloy market is characterized by a very long communication distance between the consumer and the producer. This has created a situation where it has been difficult to change ferroalloy properties. In this paper different FeNi and FeCr-compositions are discussed and their merits for stainless steel-makers in different situations are compared using the process models applied at Outokumpus Avesta works and Acerinox&apos;s Columbus operation Keywords Ferroalloy design, ferrochrome, ferronickel, stainless steel making, UTCAS software.

Jan 1, 2010

By I. du Plessis

The metallurgical response of a difficult to treat coal and an easy to treat coal orebody were investigated in terms of the coal yield and the coal quality in a basic coal recovery flowsheet. The purpose of this paper is to show trends and derive principles for the treatment of different coal types. This investigation entailed using the LIMN simulator to simulate the metallurgical response by varying the plant operational parameters. The controllable plant variables investigated were: ?Cyclone size ?Screen and hydro-cyclone cut points ?Medium cut density ?Feed particle size distribution.

Jan 1, 2010

By T. T. Matuludi

Kleinkopje Colliery has five Wemco drums that were installed and commissioned in 1978. Over the years, there have been remarkable changes in mining and geological conditions at the colliery. First, an increase in the percentage of fines was recorded, which resulted in an uneven split or an imbalance in silo levels between material feeding the cyclone (-12 mm) and Wemco drum (+12 mm) sections respectively. This problem was solved by doing modifications around the banana screens to allow finer material to the drums. The imbalance challenge was then followed by spontaneous combustion that takes place in situ and results in low product yield. The results obtained from efficiency tests indicate that although there is a limit in the percentage of -6 mm material in the feed, Wemco drums are still very efficient and applicable to the current mining conditions. These results also suggest that it is essential to lower the throughput when the drums are treating low yielding coal.

Jan 1, 2010

By J. R. Percival, L. Ip, M. D. Piggott, S. J. Neethling

Component wear due to particle-laden flow is a significant challenge in the minerals processing industry in the handling and transportation of abrasive mineral slurries. Studying wear through experimentation is time-consuming and expensive; therefore possessing the ability to accurately simulate, understand and predict wear in these complex environments is highly desirable. The ability to predict wear is important in both the design of equipment in order to maximise the performance over the wear life of the components, as well in minimising potentially costly and dangerous failures and unscheduled maintenance.. Particle-induced wear is a complex problem, requring an understanding of coupled fluid-solid motion, geometry deformation in response to fluid-solid behaviour, moving geometries and wear modelling. Although the literature demonstrates that rebounding particles and changes to surface profiles can have a significant effect on subsequent wear rates and patterns, the challenge of implementing a model to account for this effect in complex geometries has been addressed by only a few authors in the literature. This paper describes a new wear simulator, leveraging fluidity, an open-source, massively parallel, finite element based CFD simulator capable of unstructured adaptive meshing. The wear simulator includes the ability to model particle-laden flow using representative Lagrangian particles and dynamic remeshing of geometry in response to wear and component movement. These capabilities are demonstrated using wear and the associated dynamically deforming boundaries within a Coriolis tester arm, with the results comparing favourably with the experimentally observed wear patterns. Keywords: CFD, wear, two-phase flows, anisotropic mesh adaptivity, boundary deformation

Jan 1, 2020

By M. Krasowska, W. Skinner, R. K. Asamoah

Understanding chemical interactions at solid-liquid interfaces have played a pivotal role in improving mineral flotation performance, increasing the rate of mineral crystallisation and profitable leaching of valued minerals and metals. This paper highlights gold leaching with links to surface and interfacial chemical processes occurring, and opportunities to maximise extraction while reducing usage of more recent scarce resources. From the review, there is a significant link between surface and interfacial processes and gold leaching performance. Evidently, gold leaching kinetics could be increased by changing leaching conditions, including manipulating the surface and interfacial interactions. Control of surface and interfaces during gold extraction could enhance rapid, smarter gold extraction and mitigate formation of passivation layers. Keywords: Surface and interfaces, refractory ores and concentrates, gold leaching, reaction mechanism and kinetics

Jan 1, 2020

By D. Hanekom

Over the past couple of years, Anglo Platinum has made extensive use of technology within the core disciplines (geology, evaluation, survey, and planning) that collectively form part of mineral resource management (MRM). While these technologies were primarily developed to enable geology, evaluation, survey, and planning to carry out their daily tasks, with the main objective of supporting the mine?s production effort, they have also enhanced the disciplines? ability to produce the required outputs within the annual business planning cycle. Anglo Platinum has developed a very comprehensive business planning process, and these technologies play a vital role in enabling both the quality and quantity of inputs into the process, and also the value-add of the final product. This prompted a question regarding the practical application of the CADSMine software. If we changed our thinking in how we applied the software, would it be possible to further improve on the time taken to deliver a business plan? In changing the current planning approach, would we be able to further simplify the process? Is there a way to reduce the data generated in order to enhance the time taken to do reporting, as the CADSMine software is totally network dependent? Less data should equal faster reporting. This paper focuses on the practical application of the CADSMine software, and demonstrates the value-add to the business planning process that can be gained if the mine design methodology is changed from individual panels to bigger blocks representing a raise line.

Jan 1, 2012

By Q. G. Reynolds

The problem of direct-current plasma arc behaviour, interaction, and dynamics is considered in the context of metallurgical DC arc furnace applications. Particular attention is paid to the transient flow behaviour of arc systems. A mathematical formulation of the physics used to describe the arc system is presented, and includes the spatial and temporal evolution of fluid flow, heat transfer, and electromagnetism. Based on this formulation, a numerical model is developed using a finite difference approach on a regular cartesian grid in both two and three dimensions, with a special focus on robust stability, high resolution modelling, and high performance. A collection of results produced using the numerical model to study pilot plant-scale furnaces is then presented. These address a range of process and design variables and their effect on the numerical model?s results. Where possible, the qualitative behaviour of the model is compared to available experimental data. A number of novel effects and phenomena are seen in the dynamic behaviour of the DC plasma arc model for both single and multiple arc systems, which may lead to improved understanding, control, and manipulation of such systems where they occur in industrial applications. Keywords Pyrometallurgy, direct-current furnace, plasma arc, modelling.

Jan 1, 2010

By M. Z. Naghadehi, F. F. Nasategay, J. Sattarvand, R. Battulwar, E. E. Gohari

After the recent increase in catastrophic failures of tailings dams such as the Burmadinho, Brazil failure in 2019, the mining industry has actively engaged in the stabilisation of tailings dams. Most of the tailings storage facility (TSF) guidelines suggest a laborious action that can be facilitated through imaging by unmanned aerial vehicles (UAVs). Although UAVs are not unknown to most mining operations, automated rill detection through aerial image processing is a new concept. This study utilises images from sites in the U.S. and employs semantic segmentation with a UNet architecture to detect location and size of these rills. The developed model can be used as a tool for monitoring surface erosion of TSFs.

Sep 1, 2021

Acid heap leaching has been extensively applied to the processing of copper oxide ores, with recovery of copper by solvent extraction and electrowinning. Heap leaching has also been extended to the treatment of secondary sulphide copper ores, where oxidative conditions are generated in aerated heaps by the bacterially-assisted oxidation of ferrous iron to ferric iron. The treatment of low-grade chalcopyrite ores has recently been the focus of research, with Mintek playing a prominent role. When processing chalcopyrite ores, more complex column test work is performed, which incorporates the prediction and simulation of temperature behaviour in pyrite-containing heaps. Mintek has devised a trade-marked column leaching apparatus (SmartColumn?) for the simulation of the natural temperature profile development in pyrite-containing heaps. As heap leach applications are becoming more complex, the parameters that need to be built into the design and operation of heap leach plants are growing in number, and the amount of data to be collected and processed, and the number of decisions to be taken daily, are also increasing. Mintek has therefore developed the HeapStar® administrative advisory software, as a guidance system to ensure that the correct protocols are implemented at various stages of the leach cycle.

Jan 1, 2012

By C. Gatschlhofer, A. Krammer, H. Raupenstrauch, T. Hochsteiner, A. Holzer, L. Wiszniewski

The rising demand for lithium-ion batteries, coupled with international climate targets, emphasises the need for circular economy and zero-waste recycling approaches. However, so far, no industrial-scaled solutions are available that fulfil global recovery targets. Therefore, a novel pyrometallurgical reactor was developed at the Chair of Thermal Processing Technology at Montanuniversitaet Leoben to avoid lithium slagging and recover volatile elements via the gas phase. Nevertheless, previous results show that several impact factors, including interfering elements or pre-treatment steps, strongly limit the recycling efficiency of black mass. To simulate the black mass and provide feedback on possible influences of pre-treatment steps, cathode material from production with additives of interfering elements was analysed regarding melting behaviour. The results show that formation of a further processable alloy was increased by almost 50% when pretreatment steps were excluded, indicating pre-treatment steps as a major influence to be considered within this specific recycling route.

Jan 1, 2023

By W. E. Stumpf

"SynopsisSouth Africa recently announced a resurgence in its commercial nuclear power programme. The implications for the development of the necessary high-level manpower within South Africa’s tertiary educational system and its national research and development (R&D) capacity in materials science and engineering, as well as in other engineering disciplines, are placed into perspective. An organized national process of developing this manpower by moving away from the previously high-risk and costly ’large programmes’ to rather a selection of ‘small and better’ research projects and a redefinition of what constitutes ‘nuclear materials’ are proposed as parts of this strategy.IntroductionSince 2008, and more particularly in 2014/2015, South Africa has woken up to the fact that significant steps need to be taken to ensure sufficient electricity generating capacity for the future, even beyond the coal-fired stations at Medupi and Kusile currently under construction. It is, therefore, encouraging to see some active large-scale wind farms in the Eastern Cape near Jeffrey’s Bay, in the Couga area, and others in the Western Cape already in operation. In addition, many solar energy projects are also progressing from the small localized scale to larger programmes in the Northern Cape, which may contribute some capacity on a national basis. South Africa needs to tap into its renewable resources of wind and solar much more, but will these projects solve the country’s long-term industrial needs? Unfortunately not. One cannot run mines and trains on solar cells. Industry needs reliable baseload capacity, and with very limited easily accessible hydrocapacity this leaves really only coal, possibly natural gas, and nuclear power as options. South Africa’s current over-reliance of about 90% on coal–fired power, however, places it in an internationally vulnerable position, and diversification into a more equitable energy mix should be a national priority for the medium to long term. South Africa cannot significant climate change confronting the human race, as the IPCC cautioned in 2013, and will have to adjust its future energy reliance to a more balanced combination of sources."

Jan 1, 2015

By T. De Lange

Extensions to the beneficiation plant at the Grootegeluk Coal Mine are currently being planned in order to provide power station coal for Escom&apos;s Matimba Power Station, presently under construction. A simulation model was developed on the Olivetti M-24 microcomputer to facilitate the development of the envisaged flowsheet. The computer program simulates the heavy-medium separation and screening unit operations. The model is based on the construction of the Tromp partition curve described by an arctangent function, allowing ideal and non-ideal separations. The paper discusses the determination of the parameters required by the arctangent curve from standard process parameters such as Epm, Wolf cut-point, Tromp cutpoint and screening efficiency. The accuracy and shortcomings of the model are discussed, while an overview of the application of the model to evaluate borehole and bulk sample analyses is also given. It is concluded that the model is an invaluable aid to general flowsheet development.

Jan 1, 1987