Search Documents

By G. R. Marchant, B. K. Loveday

"A mathematical model has been developed for flotation circuit simulation. This model was designed to investigate the effect of varying the circulating loads and to determine whether an improvement in overall efficiency could be gained by a size separation prior to flotation.Model parameters were obtained by regression to plant data. Highly correlated parameters in the model were combined to reduce the number of parameters so that the need for excessive data gathering was eliminated. Mass balance smoothing was used to obtain a consistent data set for regression.The results of the simulation indicate that for the same grade of concentrate, an increase in copper recovery of 0.6 per cent may be Possible by increasing the circulating loads. The results of the simulation also indicated that recleaning of the plus 200-mesh material may be beneficiaL."

Jan 1, 2014

By L. von Ketelhodt

During the period October 2003 to June 2004, a containerized optical sorting pilot plant was operated at Kloof Gold Mine on a waste rock dump. In this paper, we describe the test work and its results leading to the decision to operate this pilot plant. This paper presents the operational data and financial figures achieved during this project, in particular, for the month of June 2004 when the plant was run at full capacity on three shifts, 24 hour operation. These results are also extrapolated and presented to show the profitability of such an operation at today?s gold price levels and cost structure.

Jan 1, 2009

By G. R. Drennan, N. J. Wagner, M. J. T. Sebola

The Soutpansberg Coalfield hosts South Africa's hard coking coal reserves. However, coals in this region are understudied compared to other coalfields in the country. This study characterizes the properties of fine-float fraction samples extracted from a wide diameter borehole core in the Makhado Project, Tshipise sub-basin, Soutpansberg coalfield. Conventional analyses were used to determine the coal quality, petrographic composition, mineralogy, geochemistry (including trace element and rare earth element composition), and free swelling index of samples from six coal horizons and three partings from the economic No.6 Seam. The coal samples are classified as medium rank bituminous C coals (0.88 %RoVmr, 0.92 %Rmax) and are highly vitrinitic in composition (97 vol% mineral matter free (mmf)). The samples show strong caking potential (FSI of 9). The total rare earth concentrations range between 570 and 3193 ppm in the ash samples. Preliminary analysis show all but two samples are promising sources of rare earth elements as the total concentrations exceeded the 1000 ppm cut-off grade. Further research is required to confirm these preliminary findings.

Aug 2, 2022

By Kedikilwe Oageng

Effective perimeter control during drilling and blasting is critical not only to blasting results but also to the overall stability of the pit over its entire life span. A pit where perimeter control is not given enough attention when conducting drilling and blasting operations, often experiences over-break or back break beyond final pit wall limits, and therefore has a relatively high probability of failure. Such a pit also becomes unsafe, sometimes not easily accessible, has increased loading costs due to production of oversize, longer cycle times and often problems are encountered when blasting subsequent benches. All these are undesirable consequences, which have negative cost implications. Specialised blasting techniques such as trim blasting and pre-splitting have over the years proved to be effective perimeter control measures. However, the success of these techniques is directly attributable to the time and effort given to the processes. This paper presents results of a project undertaken to monitor, review and optimize the trim blasting and pre-splitting processes at Orapa Diamond Mine in Botswana. The project was specifically incepted to improve the final wall conditions, which continued to deteriorate due to persistent over-break during blasting. The paper also analyses the results obtained against a benchmark of results taken prior to project implementation. Specific blast design parameters which are critical to blasting results were identified as problem areas after auditing of the pre-implementation drilling and blasting practices. These include drill-hole depth, spacing, splitting factor for pre-splits and timing of trim blasts. The impact of different rock types on the results was also studied, and recommendations were made at different phases of the project and results obtained after implementation analysed until optimum results were achieved.

Jan 1, 2008

By S. G. Mgenge, J. D. Steenkamp

Tronox Namakwa Sands operates two ilmenite smelters for the production of high-titania slag and low-manganese pig iron. Slag or metal is tapped from one of two product-specific, bi-level tap-holes. In this paper the refractory design specific to the tap-hole refractory layout is described, as well as practices for slag and metal tapping and refractory maintenance. Further developments planned are briefly described.

Jan 1, 2014

By Ronald J. Roman

All mining and milling complexes can, within limits, operate at a variety of production rates. Factors of economic importance that are affected by production rates are costs per unit production, recovery and product grade. Once the relationship between the production rate and cost is established, dynamic programming techniques can be used to define the optimum production schedule (that is, the production schedule that maximizes the present worth of the operation) for the life of the deposit. In general, assuming that the capacity and efficiency of the physical plant remain unchanged throughout the life of the deposit, the optimum production rate is not constant for the life of the deposit, but declines gradually as the deposit is being exhausted.

Jan 1, 2014

By D. -X. Li

The paper covers many literature reports of processes using nitrogenous species as an oxidant for processing refractory gold ores, especially development in the pretreatment of refractory gold minerals by nitric acid. These processes include the high-pressure and the atmospheric-pressure oxidation methods. High-pressure oxidation processes are difficult to carry out, because they require high-capital cost autoclaves. Atmospheric-pressure oxidation processes are easier to manipulate, but complete absorption and reuse of NOx is difficult or multiple-stage absorption must be established for its reuse. So, some new methods were developed, such as catalytically oxidizing technology of NOx to allow subsequent recovery of gold. Keywords: nitric acid; pretreatment; refractory gold

Jan 1, 2009

By S. Kauchali

"Underground coal gasification (UCG) is recognized as an efficient mining technique capable of chemically converting the coal from deep coal seams into synthesis gas. Depending on the main constituents of the synthesis gas, chemicals, electricity, or heat can be produced at the surface. This paper provides a high-level graphical method to assist practitioners in developing preliminary gasification processes and experimental programmes prior to detailed designs or field trials. The graphical method identifies theoretical limits of operation for sensible gasification within a thermally balanced region, based primarily on the basic coal chemistry. The analyses of the theoretical outputs are compared to actual field trials from sites in the USA and Australia, with very favourable results. A South African coal is studied to determine the possible synthesis gas outputs achievable using various UCG techniques: controlled retractable injection point (CRIP) and linked vertical wells (LVW). For CRIP techniques, an important result suggests that pyrolysis, and subsequent char production, are important intermediate phenomena allowing for increased thermal efficiencies of UCG. The conclusion is that South African coals need to be studied for pyrolysis-char behaviour as part of any future UCG programme. The results also suggest that UCG with CRIP would be a preferred technology choice for Bosjesspruit coal where pyrolysis dynamics are important. Lastly, the use of CO2 as oxidant in the gasification process is shown to produce syngas with significant higher heating value. Introduction and literature surveyCoal is a commonly utilized fossil fuel, providing over 40% of global electricity demand and about 90% of South Africa’s primary energy needs. However, less than 20% of the known world resources are suitable for possible extraction using conventional surface and underground mining techniques (Andrianopolous,, Korre, and Durucan, 2015). Underground coal gasification (UCG) has the potential to recover the energy stored in coal in an environmentally responsible manner by exploiting seams that are deemed unmineable by traditional methods. The UCG process, if successfully developed, can increase coal reserves substantially. For example, in the Limpopo region of South Africa alone, the estimated potential for UCG gas, based on existing geological records, is over 400 trillion cubic feet (TCF) natural gas equivalent – this is about a hundred times more gas than the existing 4-TCF Pande-Temane natural gas field reserve in Mozambique (de Pontes, Mocumbi, and Sangweni, 2014)."

Oct 1, 2018

This paper examines manning best practice in the Australian mining industry, comparing the mining of gold with mining of other commodities. In particular, the paper considers a range of mining operations and their manning levels as measured by operational benchmarking. The benchmarking results presented cover 7 open pit and 14 underground studies of gold mines in Australia from a database of over 50 studies. The data were collected as part of AMC?s benchmarking and operational improvement studies conducted between 1999 and 2009. The results examine overall manning levels in mining, processing and administration functions. Manning levels for a range of mining methods, including open pit and underground methods, are segmented. Productivity measures such as ore tonnes per man day and metres developed per man day are presented and where direct relationships can be established, the relationships are described. The proportion of supervisory to operations personnel and labour costs as a percentage of total operating costs is highlighted. Minimum manning requirements for the range of mining methods are indicated, irrespective of the size of the operation. The benchmarking results provide guidance by indicating a range of manning numbers and trends which are likely to be appropriate for the scale and type for a range of mining operations. When combined with benchmarked productivity and cost data, manning results help identify potential areas for business improvement, driving gains in the efficiency of labour. Finally, the paper considers perspectives on best practice for manning and the limitations in application of this type of analysis in a global context.

Jan 1, 2009

By C. A. Preece

Finsch Diamond Mine, part of De Beers Consolidated Mines (DBCM), is situated between Kimberley and Postmasburg in the Northern Cape, South Africa. The kimberlite pipe was discovered in 1960 and De Beers assumed full mining rights three years later. Production commenced in 1966 from an opencast mine, and the operation moved underground in 1990 by developing and implementing a new mining method of blast hole open stoping. A mechanized block cave was brought into production in 2005. While block caving was not new to DBCM, with productive caves having operated in Kimberley and Cullinan, from the outset, the Finsch caving operation was designed as the most advanced with a semi-automated ground handling system. The extraction level was laid out as a single sided herringbone system due to the very poor ground conditions on the south side of the pipe. These factors combined to create a unique environment, which necessitated a completely new approach to draw control. The required system was developed by a team consisting of DBCM personnel from head office and Finsch, GEMCOM and Sandvik-Tamrock, the equipment manufacturers. It was essential that the system could be run quickly, provide daily updates and issue calls directly to the LHDs. It was also important that the base data were obtained from the resource model, which was to be depleted on a monthly basis, thus forming a close link between mine planning and draw control. A further requirement of the system was that it would form a central database for the extraction operation where all data pertaining to delays and changes in conditions, be they production or ground condition related, could be recorded and analysed. The design brought together empirical rules and tables developed at Cullinan plus concepts from programming developed for the front cave at Koffiefontein so that the new system was based on sound practical experience. These facets were incorporated into PCBC (GEMCOM) and CMS and PCS (Sandvik-Tamrock programmes). The system has now been operational for just under a year and while modifications have had to be made, it has proved itself as a practical and reliable tool with which to manage the draw control at Finsch. The system is unforgiving and has forced the production team to focus on the specified drawpoints. Problems have been encountered but most of these have been related to re-educating a workforce, familiar with a flexible mining method, to the strict discipline required for a modern block cave.

Jan 1, 2007

"SAMPLING: THE IMPACT ON COSTS AND DECISION MAKING1. INTRODUCTIONFor years those in the minerals industry have been taking samples to assist them in making decisions; whether they be about investing billions of rand in a new mining operation, or simply whether a truck load of mineralised material should go to the mill or the waste dump, - we need a sample to help us make our decisions. This paper emphasises the importance and significance of sampling as a process, some of the associated technical problems and some of the advantages, especially in the light of traditional approaches that has usually left mine sampling to the least educated and lowest paid individuals on the mine. Perhaps the most important aspect that requires attention is the variability, usually measured in terms of precision, that tends to infect the sampling procedures. Francis Pitard 12 has stated: ""There is no such thing as reliable feasibility studies, unbiased ore grade control, accurate environmental assessments or effective process control, if you cannot identify and minimize the seven (ten) major sources of sampling variability. "" It is these ten sources of sampling variability and the way they arise that are briefly investigated. Variability is measured in terms of variances and rather than being self-compensating, there is good evidence to indicate that they are in fact additive at every step in the sampling and analytical process."

Jan 1, 2014

By P. C. Pistorius, D. Kruger, Y. Kacar

Because of its superior properties, stainless steel has been widely used for many applications. Nonmetallic inclusions can influence the quality of stainless steel products. A set of samples was used to track the response of inclusion composition during processing of a heat of titanium-bearing 18% chromium steel, from deoxidation after decarburization, to the solidified slab. The oxide inclusions responded as expected to additions of deoxidizers and calcium treatment, changing from silica to alumina and spinels, and then to calcium aluminates. The samples confirmed that titanium nitride can nucleate on liquid calcium aluminate during steel solidification.

Aug 1, 2021

By M. J. Sapko

The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) recently conducted full-scale explosion experiments; these experiments evaluated the strength characteristics of various seal designs used for safely isolating worked-out areas in underground coal mines. Large-scale explosion tests were conducted within the multiple entry section of PRL's Lake Lynn Experimental Mine (LLEM) employing the only currently accepted test method endorsed by the Mine Safety and Health Administration (MSHA) for seal design in American mines. These explosion tests are labor-intensive, expensive to conduct, and can interfere with other critical underground safety and health research programs conducted by NIOSH. Therefore, the PRL has developed an alternative seal evaluation method, based on a hydrostatic pressure loading concept, that can facilitate the in-situ testing of seals in an operating mine. Two chambers within LLEM and one within the Safety Research Coal Mine (SRCM) were used for hydrostatic pressure loading various seal designs. The results from tests in these chambers compare favorably with those from the large-scale explosion tests in the multiple entries. Preliminary size-scaling relationships for predicting the strength of standard seal designs as a function of entry size is also presented. In addition to testing seal designs at the required 20 psi static pressure level, the new facilities also allow for the determination of the seal's ultimate failure pressure. This new approach shows promise as an alternative evaluation method for improving mine sealing technologies which, in turn, will enhance the safety of the underground personnel.

Jan 1, 2003

The depletion of favourably located and higher-grade mineral deposits, combined with more favourable metal prices and higher capital costs, has stimulated research into heap leaching of lower grade ores and wastes. This has resulted in renewed interest in heap leaching of uranium ores, and in the development of processes for the bacterial heap leaching of low-grade chalcopyrite ores and the acid heap leaching of nickel laterites. A complete programme of heap leach testwork typically involves a sequence of bottle roll tests and column tests, followed by piloting on test heaps. The initial testwork is aimed at determining the amenability of the ore to heap leaching, which depends on the characteristic of the ore with respect to porosity and permeability to leach liquor, acid consumption, metal recovery and percolation. Subsequent phases of the testwork focus on the development of the process design criteria for the treatment of the ore. Basic techno-economic models have also been developed as a tool for the initial estimation of heap leach viability. Mintek has also developed in-heap monitoring probes, coupled to an operator guidance system, in order to assist the operator in achieving optimal conditions for bacterial growth and heat preservation during pilot-plant operation.

Jan 1, 2009

By M. Kamali

In this research, in order to predict the peak particle velocity (PPV)(as vibration indicator) caused by blasting projects in the excavations of the Karoun III power plant and dam, three techniques including statistical, empirical, and neural network were used and their results were interpreted and compared. First, multivariate regression analysis (MVRA) was used as statistical approach. Next, PPV was predicted using some widely used empirical models. Lastly, an artificial neural network was used. In the ANN model, maximum charge per delay, total charge per round, distance from blast site, direction of firing, blasthole length, number of blastholes, total delay in milliseconds, number of delay intervals, and average specific charge were taken into consideration as input parameters and consequently the PPV as output parameter. The results of the techniques were interpreted from two points of view. Firstly, the correlation between the observed data and predicted ones, secondly the total error between observed data and predicted ones. The MVRA had a satisfactory correlation but its error of estimation was comparatively very high. The empirical model had reliable correlation and a small error of estimation; in total the results of empirical method were more reliable than those of MVRA. Generally, the ANN approach showed very high correlation and a very small error. The results of this research indicated that the ANN model is the best predicting model for PPV in comparison with other approaches.

Jan 1, 2010

When designing coal mine roof support, it is necessary to account for the uncertainties and variability that inherently exist within the rock mass and support elements. The performance of a support system is affected by these uncertainties, which are not taken into account in the current deterministic design methodologies used in South Africa. The key to the design of a roof support system is a better understanding of roof behaviour and uncertainties that can been countered during extraction. This paper sets out to develop a method that takes all uncertainties that exist within the rock mass and the mining process into account and provides a quantitative risk-based design methodology.

Jan 1, 2009

By T. Oberthür

The Great Dyke of Zimbabwe constitutes the world?s second largest reserve of platinum group elements (PGE) after the Bushveld Complex in neighbouring South Africa. Within the Great Dyke, economic concentrations of PGE are restricted to sulphide disseminations of the Main Sulphide Zone (MSZ), which are currently mined at the Ngezi, Unki, and Mimosa mines. Near-surface oxidized MSZ ores have a large potential. Their total resources are in the range of ca. 160 ? 250 Mt; however, all previous attempts to extract the PGE from this ore type proved uneconomic due to low PGE recoveries (<< 50 per cent) achieved by conventional metallurgical methods. Within the ores of pristine, sulphide-bearing MSZ, the PGE are bimodally distributed. Platinum occurs mainly in the form of discrete platinum group mineral (PGM) grains (mainly bismuthotellurides, sulphides, and arsenides), whereas approximately 80 per cent of the Pd (and some Rh) is hosted in pentlandite. Within the oxidized MSZ ores, the PGE are polymodally distributed. Whereas arsenide- and sulphide-PGMs, making up ca. 25 per cent of the original Pt content of the ore, largely remain stable (relict PGMs), the remaining PGMs are disintegrated. The base metal sulphides are destroyed, partly releasing their base metal and PGE contents, and are replaced by iron oxides or hydroxides. Unspecified amounts of the PGE are redistributed and either form secondary PGMs, are found in chemically and mineralogically ill-defined (Pt/Pd)-oxides or hydroxides, or in iron-hydroxides, Mn?Co-hydroxides, and in secondary silicates. The problematic processing of oxidized MSZ ores is attributable to their complex nature and polymodal distribution of the PGE, prohibiting a significant upgrading of the ores by conventional metallurgical methods. Therefore, only bulk leaching methods are viable for ore treatment, and novel metallurgical methods have to be developed for the processing of these ores. Our ongoing work aims at locating the PGE in their mineralogical form in order to understand the mineralogical balance of the PGE in the ores and thereby facilitate the evaluation of metallurgical options for their recovery. A short overview on options and recent advances regarding the recovery of the PGE from oxidized ores is given.

Jan 1, 2012

By O. O. Ogunmodimu, D. K. Weatherley, M. S. Powell

Discrete element methods (DEM) have provided the ability to resolve the complex phenomena experienced by ore within comminution devices such as tumbling mills. The new developments in DEM techniques and the corresponding increase in computational power have made it more feasible to study the movement of individual ore particles as they traverse a tumbling mill. A range of information can be extracted on individual particle impact histories, such as kinetic energy at the time of collision, velocities of individual particles, per-particle stress tensors, impulse, and collision energy. DEM codes have been modified to provide required information that can be analysed in associated software to investigate the impact of varied operational parameters on the resultant granular dynamics. This paper explores the reaction of individual ore particles to the breakage environment within a tumbling mill using DEM techniques and studies the stressing conditions that would lead to either impact or abrasive breakage. Keywords: DEM, comminution, tumbling mill, breakage

Jan 1, 2020

By F. Mulenga, S. Ncube

Rock fragmentation methods in open pit gemstone mining have developed to give priority to safety, environmental sustainability, and crystal integrity. Though effective, traditional drill-and-blast techniques can generate vibrations, adverse emissions, and structural damage, all of which could be detrimental in fragile geological settings. Costs, application in hard rocks, and operational inefficiency remain issues, despite the fact that mechanical excavation and evolving thermal and hydraulic technologies have provided some solutions. In response, there has been a growing interest in non-explosive alternatives, particularly soundless chemical demolition agents. This paper provides a comprehensive evaluation of non-blasting rock fragmentation techniques with an emphasis on the efficiency, economic considerations, and operational constraints of soundless chemical demolition agents SCDAs in gemstone mining. Soundless chemical demolition agents technology has shown promising results in preserving gem purity and reducing environmental impact, despite ongoing challenges. These include increased reaction times that hinder output, decreased performance in saturated or high-stress environments, and temperature sensitivity. The contextual relevance of soundless chemical demolition agent application in lateritic regions, such as Zambia, is discussed based on published studies and reported operational experience. Developments in formulation chemistry, fracture modelling, and borehole design have also demonstrated promise in overcoming current limitations. This review identifies the main factors that affect soundless chemical demolition agent performance and brings together reported strategies that can improve their use in high-value mineral extraction through a comprehensive review of recent studies. Ultimately, this article supports a paradigm change towards excavation techniques based on state-of-the-art non-explosive technology that are safer, cleaner, and more accuracy focused.

May 8, 2026

By M. Yavuz

Determining the most convenient plant location is one of the most commonly encountered problems in engineering applications. This paper presents a fuzzy multiple attribute decision making (FMADM) model which is developed for the selection of the optimum plant location for natural stone factories in the mining industry. The criteria affecting the decision making process in natural stone industry were determined to solve the plant location problem in the FMADM model. To determine the optimum plant location for a new natural stone factory, which is planned to be established by a mining firm located in the Eskisehir region of Turkey, an analysis was carried out by incorporating the method and the analytic hierarchy process (AHP) method. The analysis shows that the Yager?s method can easily be applied to the selection of plant location in the natural stone and mining industry when the difficulties encountered in the application process of the AHP method is taken into account. Keywords: Natural stone, plant location, decision making, Yager?s method, analytic hierarchy process (AHP).

Jan 1, 2008