Search Documents

By M. Hakala, P. Tolppanen

A method to predict stress-induced failures around excavations based on the mapped geological and rock mechanical information is studied. Totally of 7 km of newly excavated tunnels are mapped in the Inmet’s Pyhäsalmi mine in Finland at depth between 1000 - 1440 m from which the results and conclusions from the firstly mapped 1.7 km of tunnels are reported. The main rock type at the site is very hard volcanite having uniaxial compressive strength of 230 MPa in median and GSI-value 72 - 80. The maximum in situ stress around the tunnels is 65 - 85 MPa. The prediction of observed stress failures was preceded by comparing elastic 3-D simulation results of tunnels with three statistical yield criteria. Read’s or Hoek & Brown’s yielding criteria are found the most relevant, though, the effect of anisotropy was found to be significant. The most important parameters having a correlation with stress failures are the tunnel orientation and the foliation of rock. Also, the rock type and its strength, tunnel shape and the geological anomalies have their effects. Further, a delay time on mapping was found to clearly diminishing of the most violent failures. Une méthode de prédiction des contraintes à la rupture autour d'excavation, établie sur la base de cartographie géologique et d'information sur la mécanique des roches, à été étudiée. Au total, 7 km d'un tunnel nouvellement percé à une profondeur de 1000 à 1400 m ont été cartographiés dans la mine de Inmet’s Pyhäsalmi en Finlande. La roche principale du site est une vulcanite dur ayant une résistance à la compression uniaxiale de 230 MPa (valeur moyenne) et une valeur GSI de 72 - 80. La contrainte in situ maximale autour du tunnel se situe entre 65 et 85 MPa. La prédiction des contraintes à la rupture observées a été évaluée en comparant les résultats d'une simulation 3D d'un tunnel avec trois critères de limite d'élasticité statistiques. Le critère de limite d'élasticité de Read ou de Hoek & Brown’s se trouvent être les plus important, même si les effets de l'anisotropie sont significatifs. Les paramètres les plus importants ayant une corrélation avec la rupture sont l'orientation du tunnel et la foliation de la roche. De plus, le type de roche et sa résistance à la compression, la forme du tunnel et les anomalies géologiques ont aussi leur importance. Finalement, un délai dans la cartographie résulte en une diminution nette des ruptures violentes. Basierend auf kartierten geologischen und felsmechanischen Informationen, wird eine Methode untersucht, um spannngsbedingtes Versagen um Ausbrüche herum vorherzusagen. Insgesamt werden 7 km neu ausgebrochenen Tunnels in einer Tiefe zwischen 1000 und 1400 m in der Inmet Pyhäsalmin Mine in Finnland kartiert. Das hauptsächlich vorkommende Gestein ist sehr hart und vulkanischen Ursprungs mit einer mittleren einachsialen Druckfestigkeit von 230 MPa (Medianwert) und einem GSI-Wert von 72-80. Die maximale In-situ-Spannung im Tunnel beträgt 65-85 MPa. Die Vorhersage von beobachteten Spannungsversagen werden weitergeführt indem man elastische 3-D-Simulationsergebnisse von Tunneln mit drei statistischen Fliesskriterien vergleicht. Read's oder Hoek's Fliesskriteria werden dabei als die relevantesten Kriterien angesehen, obwohl auch der Effekt der Anisotropie als wesentlich erachtet wird. Die wichtigsten Parameter für eine Korrelation von Spannungsversagen sind die Orientierung des Tunnels und die Schieferung der Gesteinsschichten. Desweiteren haben Gesteinsart, Tunnelprofil und geologische Anomalien ihren Einfluss. Ausserdem zeigt sich, dass eine Verzögerung bei der Kartierung die ausgeprägtesten Versagen deutlich verringern.

Jan 1, 2003

By A. F. Collings

The processing of heavy mineral concentrates can be enhanced by the use of power ultrasound to clean their surfaces of oxidation products and fine coatings, mainly through the large, but very localized forces, produced by cavitation. Results are presented of the application of power ultrasound to remove coatings from the surfaces of mineral sand concentrates in order to improve the sharpness of their high-tension separation and, in some cases, the quality of the low iron components such as zircon. Improvements of 10–15% in recovery and up to 20% in grade compared to unsonicated material were achieved in a single stage laboratory high-tension separation. Cavitation also ensures that a fresh, clean surface is presented to leachants during the leaching of suspended solids. At the same time, the effect of cavitation and the shearing effect of the sound wave passing over the solids ensure that the saturated boundary layer is kept to a minimum if not completely removed. This application of power ultrasound helps to speed up leaching processes as applied to the removal of excess alumino-silicate contaminants in some ilmenite. Keywords: Ultrasound, power ultrasound, heavy minerals, processing.

Jan 1, 2003

By P. Sharma, J. C. W. Fowler

This paper discusses the wind blast / air blast phenomenon, how it is managed in coal mines and how it might best be managed in other underground mines. L'article qui suit a pour objets de décrire le phénomène de tir a l'air comprimé et les méthodes de modération de celui-ci dans les mines de houille, et d'indiquer de quelle manière il pourrait être surmonté dans d'autres mines souterraines. Dieses Seminararbeit diskutiert die Windexplosion / Luftexplosion Phänomen, wie es in Kohlenberg-werken geleitet wird, und wie es am besten in anderen untertage Bergwerken geleitet werden könnte.

Jan 1, 2003

By S. Marsland

Reference materials have always been important for validating and controlling analytical methods. They have recently become even more important as quality requirements have become more stringent and customer demands for properly verified and controlled results increase. Clients, especially from the resource exploration industry, demand critical validation of all results reported. Mintek has been producing geological and semi-processed ore references since the early 1970s and recently, due to increase in demand, other manufactures have entered the South African market. This paper describes analytical challenges from the customers? perspective, the customers being metallurgists, mine geologists, environmental scientists and geologists from resource companies. Reference materials with their appropriate use and a good understanding, can aid greatly in building confidence in the results, choosing the right laboratory for a project, deciding which set of results is correct and providing evidence to the customers? clients that the best possible results have been obtained

Jan 1, 2007

By Y. Mitani, M. Xie, G. Zhou, T. Esaki

The assessment of landslide instability and risk has become a topic of major interest for both geoscientists and engineering professionals as well as for local communities and administrations in many parts of the world. In this paper, based on a new developed Geographic Information Systems (GIS) grid-based 3D deterministic model and taken the slope unit as the study object, the landslide hazard is mapped by the index of the 3D safety factor. Assuming the initial slip as the lower part of an ellipsoid, the 3D critical slip surface in the 3D slope stability analysis is obtained by means of a minimization of the 3D safety factor using the Monte Carlo random simulation. The failure probability of the landslide is calculated by an approximate method in which the distributions of f,c and the 3D safety factor are assumed to be in normal distributions. The assessment of the earthquake triggered landslide hazard is done by the dynamic displacement analysis using the index of the Newmark displacement. All the calculations are implemented by a computational system call 3DSLOPEGIS in that a GIS component is used for fulfilling the GIS spatial analysis function. Besides the results of 3D safety factor and probability, the possible landslide body and boundary can be three-dimensionally quantitatively identified. L’ estimation des glissement de terrain et des risques impliqués est devenu un des principal sujet de préoccupation pour les géotechniciens, mais aussi pour les ingénieurs specialisés ainsi que pour les communautés et administrations locales dans de nombreuses région du monde. Dans cette étude, basé sur un modèle de maillage 3D et une approche déterniniste couplée au Système d'Information Géographique (SIG), étudiant la stabilité des versants , le lieu d'étude à risque est maillé suivant le facteur de sécurité calculé en 3D. En supposant que le glissement initial soit la partie inférieure d'un élipsoïde, l'analyse de stabilité pour le glissement critique 3D d'un versant 3D est obtenu grace à une minimisation du facteur de sécurité en 3D utilisant la méthode de simulation aléatoire de Monte Carlo. La probabilité d'un glissement de terrain est calculée par une méthode approximative, supposant la distribution de c, f et du facteur de sécurité 3D normale. L'estimation d'un risque de glissement de terrain causé par un tremblement de terre est faite grace à une analyse du déplacement dynamique suivant l'index de Newmark. Tous les calculs sont effectués par le biais d'un système de calcul appellé 3DSLOPEGIS dans lequel te GIS est utilisé pour gérer l'analyse spatiale. En plus de cela, les résultats du coefficient de sécurité en 3D, des probabilités, le terrain susceptible de glisser, et ses limites, peuvent être quantitativement évalués en trois dimensions. Die Bewertung von Erdrutsch-Instabilität und risiko sind zu einem Thema von großen Interesse für sowohl Geowissenschaftlern und Ingenieuren als auch von Gemeinden und Verwaltungen in vielen Teilen der Welt geworden. In dieser Arbeit, basierend auf einem neu entwickelten Geografische Informationssysteme (GIS) gitterbasierten 3D deterministischen Modell und mit der Böschung als Untersuchungsobjekt wird die Erdrutschgefahr durch den Index des 3D-Sicherheitsfaktors kartografiert. Unter der Annahme, dass der erste Rutsch der untere Teil eines Ellipsoiden ist, wird die 3D kritische Schlupfoberfläche in der 3D-Böschungsstabilitätsanalyse mit einer Minimierung des 3D-Sicherheitsfaktors mit der Monte Carlo Zufallssimulation erhalten. Die Fehlerwahrscheinlichkeit des Erdrutschs wird mit einer Annäherungsmethode berechnet, bei der die Verteilungen von f,c und dem 3D-Sicherheitsfaktor als innerhalb normaler Verteilungen angenommen werden. Die Beurteilung der Erdbeben-ausgelösten Erdrutschgefahr wird mit der dynamischen Verdrängungsanalyse mit dem Index der Newmark-Verdrängung gearbeitet. Alle Berechnungen werden mit einem Berechnungssystem mit der Bezeichnung 3DSLOPEGIS ausgeführt, bei dem eine GIS-Komponente zum Erfüllen der GIS räumlichen Analysefunktion verwendet wird. Neben der Ergebnissen des 3D-Sicherheitsfaktors und der Wahrscheinlichkeit kann der mögliche Erdrutschkörper und der Umfang dreidimensional quantitativ identifiziert werden.

Jan 1, 2003

By W. V. Mutler

Present day capital costs are analyzed for a 2,000 metric tonne per day (MTPD) pyrite burning plant and compared with a sulphur burning plant of the same capacity. Power, raw material and steam production rates are then compared for the two facility types. A sensitivity analysis is conducted to highlight the impact changing sulphur, pyrite, capital and operating costs have on the relative economics of these feeds. Technological improvement effects on capital cost and energy recovery are also discussed. Besides the steam produced from the burning of pure sulphur or pyrite, plants using an advanced form of heat recovery can produce up to 10 bar steam using heat from acid formation. The quantity depends on the overall water balance which is influenced by such factors as gas strength and product acid concentration. Modern materials and innovative process design also improve the ability to increase the high pressure steam from the roaster boiler in pyrite plants above the traditional 1.25 kg of superheated steam per kg of acid produced.

Jan 1, 2009

By E. Wolmarans

Dowding, Reynard and Associates Mineral Projects (DRAMP) was approached by the ARM/Lion Ore JV during July 2006 to conduct a feasibility study and control budget estimate for a new greenfield project for their NKOMATI Nickel mine 45 km east of Machadadorp. The scope included the evaluation and review of previous studies as well as a techno-economic trade-off on four possible comminution circuits ranging from conventional crushing and ball milling to fully autogenous milling. The following document encapsulates the thought process, decisions and the references used in selecting the final comminution route for the new 375 ktpm MMZ concentrator. Apart from the pilot test work performed, design simulations from a number of sources, performance results from a recently commissioned 100 ktpm MMZ concentrator, together with an understanding of the geology and mineralogy of the orebody and possible variations in the characteristics of the orebody over the life of mine were assessed. The results from all the above-mentioned work indicated that it would be possible to treat the MMZ ore at the desired throughputs to the desired grind sizes in a fully autogenous grinding (ABC-type) circuit. Autogenous milling is generally considered to be one of the higher risk milling circuits. This is mainly due to the fact that the ore, which is utilized as the grinding media, could be variable in terms of hardness and mineralogy/geology. Nevertheless, it is a very popular route as the cost benefits, more specifically the operating cost, are normally very attractive. This is especially the case when large low grade orebodies are evaluated. In North/South America, autogenous and semi-autogenous grinding circuits have been successfully employed during the past 20 years on large scale low grade operations. Taking all the above factors into account, the DRA/Nkomati project team recommended an autogenous circuit with the option to add steel to both the primary and secondary mills (if required) for the new operation in order to create the opportunity for significant operating cost savings. One has to bear in mind that all the new design simulations and decisions are based on previous work and potential unknown variations within the orebody will never be fully understood until the pit is operational for some time.

Jan 1, 2009

By J. Xiao, Y. Jiang, Y. Tanabashi, Z. Song

Modelling the effect of blasting-caused damage, anisotropy of rock masses and excavation sequence on deformational behaviour and stability of large-scale underground caverns is important in the design and information-oriented construction of the pumped storage power plant. A powerful three-dimensional numerical method that can be applied for that purpose is presented in this paper. Damaged range caused by blasting and mechanical properties of rock masses near to the walls of caverns are determined by using the back analysis approach in which three lines of the measurement results during the arch part excavation process were used to verified the simulations. Finally, applying the improved model and properties of rocks, the cavern stability and reinforcement effect of the preliminarily designed support system are also estimated for the safety in the bench excavation process. La création de modèles des effets relatifs aux dommages résultant des explosions, à l’anisotropie des masses rocheuses et à la séquence d’excavation quant au comportement à la déformation et à la stabilité des cavernes souterraines de grandes dimensions est une étape importante dans l’étude et la construction sur ordinateur de centrales hydrauliques à accumulation par pompage. Cet article traite d’une méthode numérique tri-dimensionnelle puissante applicable à cet effet. La gravité des dommages résultant des explosions et les propriétés mécaniques des roches à proximité des parois de la caverne sont déterminées par une analyse du fond dans laquelle les simulations sont vérifiées à l’aide de trois lignes de résultats de mesures prises durant le processus d’excavation de la partie arche. Finalement, la stabilité de la caverne et les effets du renforcement du système de support préalablement conçu sont estimés par application du modèle amélioré et des propriétés de la roche, pour application à la sécurité durant le processus d’excavation en gradins. Nachahmung der Wirkungen von durch Explosionen hervorgerufenen Schäden, Anisotropie der Gesteinsmassen und der Ausschachtungssequenz auf das Verformungsverhalten und die Stabilität großräumiger Untergrundhöhlen ist für das Design und den informationsorientierten Bau von Pumpenkraftwerken wichtig. Entsprechend der Vorgaben in dieser Arbeit kann ein leistungsfähiges, dreidimensionales numerisches Verfahren für diesen Zweck eingesetzt werden. Der durch Explosionen und die mechanischen Eigenschaften des Gesteins bedingte Schadensumfang im Bereich der Höhlenwände kann mit Hilfe eines retroversen Analyseansatzes bestimmt werden, bei dem die drei bei der Ausschachtung resultierenden Messlinien dazu genutzt wurden, die Simulationen zu bestätigen. Abschließend wurde außerdem durch Einsatz verbesserter Modelle und Gesteinseigenschaften die Auswirkungen vorläufig entworfener Unterstützungssystem auf die Höhlenstabilität und Verstärkungswirkungen hinsichtlich der Sicherheit bei Böschungsausschachtung abgeschätzt.

Jan 1, 2003

By J. Szlazak, A. Tor, M. Borowski, N. Szlazak, D. Obracaj

This article presents the analysis of ventilation systems used in dead-end headings, while being drilled, in coal mines. Special emphasis is put on methane and dust hazard. Mathematical model for distribution of methane concentration in a heading is given as well. This model takes into consideration sources of methane emission and change in air flow rate due to leaks in a duct line. Solving equations presented in this article enabled giving dependencies describing distribution of concentration along the heading. On the basis of these dependencies there is a possibility of determining places with higher methane concentration and ways of combating this hazard. Determining the distribution of methane concentration in dead-end headings ventilated by a separate ventilation system is of great importance as far as work safety conditions are concerned. The information obtained may be of use when finding proper places for installing methane sensors. Three kinds of separate ventilation systems were distinguished: forcing, exhaust and overlap. The development in construction of fans and spare parts of a duct line enables using both forcing and exhaust ventilation systems in headings developed by continuous miners, with length above 1000 m, in the conditions of methane, temperature and health-detriment dust hazards.

Jan 1, 2003

By I. V. Lunkin, E. B. Muhamedzhanov, A. B. Begalinov, B. R. Rakishev

Almost all the ore deposits of ferrous, non-ferrous and rare metals of Kazakstan, are exploiting by the open-cast method, are the complex-structural, multi-component ones. Their rational working requires precise organization of extracting works. In this connection it is necessary to set up the best intercommunications between drilling-blasting, excavating-loading and transport works. This requires the stable functioning of the quarry for dispatch of ore raw material of required quality with minimum of corresponding expenses. For this purpose, proceeding from the quarry’s ore output and the assumed parameters of the exploitation system, the first problem about rational arrangement of excavating-loading equipment in extracting faces is solved. By solving the problem the model with dynamic, adapting properties had been used. It was solved numerically by the method of statistical tests. By setting up the necessary link between type-sizes of excavating-loading and transport equipment, the minimum prime cost of loading and transportation of 1 ton of mining mass from the face to the receiving station was adopted as the criterion of optimality. Depending on the type of excavating-loading equipment, the efficiency function may be different. By using wheel loaders, their displacement between the faces is possible, therefore, the efficiency function of the problem may include expenses for their displacement. By using excavators like power shovel, the problem’s restrictions must exclude its displacement between the faces. The efficiency function consists of minimum expenses for loading, proceeding from set of volumes of extraction from the faces, satisfying required quality. The volumes of extraction from the faces, satisfying required quality of ore in output stream, are determined by the method of statistical tests. Sample range is given, proceeding from the restrictions for maximum productivity of the excavating-loading equipment. Volumes of extraction, not satisfying required quality, are cut off. The efficiency function meaning is then determined and minimized. Keywords: Excavating-loading equipment, its placing in extracting faces, optimal load-carrying capacity, specific expenses for loading and transportation of mining mass.

Jan 1, 2003

By A. V. Rasskazova

Theoretical substantiation of leaching of clustered ultra-fine gold by the electro-photo activated cyanide and chloride solutions is given in the paper; and processes of activation of leach solution by electrolysis and photo-activation are described. Comparative experiments on electro-photo activated leaching of ultra-fine gold from refractory ores by cyanide and chloride solutions were carried out. The material for research is primary ore of the Pogromnoe deposit (Russian Federation, Trans-Baikal Territory). The ore is characterised by the minimum sulfide minerals and the organic carbon content. Gold in ores of this deposit is presented as mainly ultra-fine. Gold inclusions in quartz and silica-alumina minerals (metasomatic minerals) are ultra-fine. Sulfide minerals (2.5-3%) are presented in ore generally by pyrrhotine (gold content does not exceed 10 g/t). Standard cyanide technology provides 49.5% gold recovery. Photo-electro activated air saturated NaCN provides 69.9% gold recovery. Laboratory research of chloride-hypochlorite column leaching demonstrated that the electro-photo activated method provided 78.9 % gold recovery to pregnant leach solution. Chloride-hypochlorite photo-electro activated solution can provide higher level of gold recovery with shorter process duration (10 days) in comparison with cyanide (40 days). The final decision regarding the choice of leach solution has to be done on the basis of technical and economic calculations. Keywords: Ultra-fine gold, cluster chemical reactions, active clusters, leaching, electro-photo activation of leach solution

Jan 1, 2020

By W. V. Mutler

Present day capital costs are analyzed for a 2,000 metric tonne per day (MTPD) pyrite burning plant and compared with a sulphur burning plant of the same capacity. Power, raw material and steam production rates are then compared for the two facility types. A sensitivity analysis is conducted to highlight the impact changing sulphur, pyrite, capital and operating costs have on the relative economics of these feeds. Technological improvement effects on capital cost and energy recovery are also discussed. Besides the steam produced from the burning of pure sulphur or pyrite, plants using an advanced form of heat recovery can produce up to 10 bar steam using heat from acid formation. The quantity depends on the overall water balance which is influenced by such factors as gas strength and product acid concentration. Modern materials and innovative process design also improve the ability to increase the high pressure steam from the roaster boiler in pyrite plants above the traditional 1.25 kg of superheated steam per kg of acid produced.

Jan 1, 2009

By G. W. Donaldson

Theoretical and engineering aspects of slimes-dam construction by G. W. DONALDSON, M.Sc. (Eng.)(U.C.T.), D.I.C. (Visitor) Tile paper reviews the recommendations made in 1959-60 as a result of research into slimes-dam construction and finds that these recommendations are still valid. The requirements for pollution control, vegetating, in situ leaching, and future development of slimes dams as building areas are considered as they affect the engineering aspects of slimes-dam construction, and it is found that these requirements can be met without any major changes to current recommended slimes-dam construction practice.

Jan 12, 1973

By G. L. Smith

As the Platinum mining industry expands in the Eastern Limb of the Bushveld Complex it is increasingly evident that a major constraint to development is a lack of appropriate infrastructure. Of critical concern are water resources and spatial development / infrastructure. This paper identifies the context for infrastructure development in the Eastern Limb and two solutions that have evolved in the areas of water supply and spatial development. INTRODUCTION In an economics context, infrastructure is considered to be the structural elements of an economy which allow for the production of goods and services, without themselves being part of the production process. Despite the lack of a specific definition, infrastructure has largely become understood as to comprise road and rail transport systems, public transport systems, airports, public educational facilities, water supply and water resources, wastewater management, solid waste treatment and disposal, electric power generation and transmission, telecommunications and hazardous waste management systems. Critically it is important to understand that infrastructure not only comprises these physical elements but also the operating procedures, management practices and developmental policies that facilitate the effective utilization and development of the infrastructure in response to societal demand.

Jan 1, 2008

By Simon Mundike, Muwindwa Lipalile

A scraper based block cave method has been successfully applied to extract the Lower Ore Body at Nchanga since the 1950?s. Since inception, scraper drifts and service ways have been supported using steel arch sets fabricated to a specific design from high strength manganese steel To reduce costs and to improve productivity, trials commenced in 2002 using fibre reinforced shotcrete as an alternative support method. One of the areas; the 2420 8E 1C trial drift was subjected to abutment loading for several months prior to undercutting and cave mining. Shotcrete installed exhibited minor cracking shortly after application but very little deterioration thereafter. Following the success of the trial, the application of fibre reinforced shotcrete was extended to other drifts. This paper describes the application of fibre reinforced shotcrete at Nchanga and outlines design and quality assurance methods employed.

Jan 1, 2005

By G. G. Rogers, A. Vna Der Linde, N. B. Strydom, W. H. Van Der Walt

Changes in the level of serum vitamin C in mineworkers by N. B. STRYDOM, M.Se., Ph.D. (Illinois) (Fellow), G. G. ROGERS, M.Se. (Pta) (Visitor), W. H. VAN DER WALT, B.Se. (Poteh.) (Visitor), and A. VAN DER LlNDE, B.Se. (O.F.S.) (Visitor) The levels of serum vitamin C in the blood of mineworkers were determined on the first and fifth days of the normal heat-acclimatization period (i.e., before and after exposure to heat) and again after I, 2, and 4 months of underground employment. Supplementary vitamin C was administered to the men during the heat-acclimatization period. Six groups of 20 men featured in the study and, except for one of the two 4-month groups, all the values were obtained after a full shift of underground work. It was found that adequate levels of serum vitamin C were maintained during the heat-acclimatization period, and the 250 mg of vitamin C given daily to each man must therefore be regarded as sufficient. The serum vitamin C decreased significantly with time of exposure to underground conditions, showing that the vitamin C utilized during heat stress is more than that provided in the men's diet. At the end of 4 months, not a single subject had more than 0,4 mg of serum vitamin C per 100 ml, most of them having only 0,3 mg per 100 ml; 90 per cent of the men had had more than 0,4 mg per 100 ml during the acclimatization period. It is therefore recommended that the mineworkers' diets should be supplemented with 100 to 200 mg of vitamin C per man per day.

Jan 5, 1977

By L. A. Cornish, L. H. Chown, S. N. Prins, R. Süss, L. Glaner, A. Douglas

Platinum-based alloys are being developed for high temperature and special applications for good corrosion and oxidation resistance. The microstructures are similar to those of nickel-based super alloys, and comprise ~Pt3Al particles in a Pt-based matrix. After assessing binary alloys, the best candidate system was found to be Pt-Al. Testing and selection of alloys based on Pt-Al were undertaken, where the ternary additions comprised Ru, Cr, Ta, Ir and Ti. As well as phase characterization work, mechanical and oxidation tests were undertaken. The best alloys were found to be Pt-Al-Cr and Pt-Al-Ru. However, the volume fraction of the ~Pt3Al was only around40 per cent instead of the ~70 per cent found in Ni-based super alloys. To increase this, trials were conducted on a range of Pt-Al-Cr-Ru alloys, the optimum composition being Pt80:Al14:Cr3:Ru3.Currently, further additions are being made to the quaternary alloys to change selected properties. As well as developing the alloys themselves, another part of the project is to compile a thermodynamic database using Thermo-Calc?. Phase diagram work has been undertaken so that the results can be input to Thermo-Calc? so that the descriptions of the phases can be optimized. The final database will allow the phases and compositions of selected alloys to be derived, thus predicting the alloys? components without necessarily undertaking further experimental work. This will aid the development of the alloys and will be a useful tool to the final developers of the alloys. Good agreement with experimental data has been observed, which is very encouraging for usefulness of the database. Keywords: platinum-based alloys, intermetallic compounds, high temperature

Jan 1, 2004

Mineral sand beneficiation plants comprise a complex combination of electrostatic, magnetic and gravity based separation techniques. These are combined and replicated in ways that provide the most efficient and cost effective separation of the valuable components. On line instrumentation has been developed at the JKMRC (eg. conductor/non-conductor(CNC) ) to measure the properties of the dry plant process streams. This paper provides results from the recent development of a novel low cost mass flow meter and discusses their combined use with the CNC instrumentation for the control of dry separation circuits.

Jan 1, 2003

By R. M. Whyte

The complexities that exist in the nature of the basic feedstock to the metallurgical process call for a high degree of ingenuity from the extractive metallurgist in seeking the best possible treatment method for a particular ore. Drawing from personal experience the author presents four case studies that demonstrate the value of creative thinking in addressing the challenges typically encountered by the extraction metallurgist. It is concluded that creative expression most often occurs in response to a perceived strong need within an organization. By deliberately laying down meaningful challenges management can stimulate innovative thinking and achieve extraordinary results.

Jan 1, 2009

By John M. L Lewis, Antoine F. Mulaba-Bafubiandi

In the irradiation of ore particles by microwave energy preferential absorption of this energy occurs in minerals having specific dielectric properties (Bradshaw, 1999). This leads to a selective heating of the various components of within the ore particle matrix. The result is a differential thermal expansion of such components and the resulting induced stresses become ideally concentrated at mineral grain boundaries (Kingman et al., 2000). Dependent upon the relative composition of absorbent, opaque and reflective components this may lead to enhancement of the inter-granular fracture of the ore particles in the initial comminution process (Fandrich et al., 1997). The potential is thus a greater proportion of free mineral grain within the fractured ore particle that may lead to improvement in subsequent mineral separation processes. As the composition of the ore dictates the result of such a treatment (Kingman et al., 2000) it is essential to evaluate the response of each ore sample on an individual basis. This paper reports on results obtained from two ore samples: the one being the zinc ore from the Black Mountain mine (South Africa) and the other a pre-concentrated sample of handpicked cobalt?copper mixed oxide ore from the Gecamines (DRC). The equipment and methods used to simulate the comminution of the samples and evaluate the level of the value liberation will be described along with the results obtained. Using King (1975), Kanellopoulous and Ball (1975), and Gungor and Atalay (1998), a comparison between the behaviour upon microwave irradiation of sulphide and mixed oxide ores leads to conclude that while the technique (i.e. microwave irradiation) is appropriate to the zinc sulphide ore, it does not seem to lead to exceptional results for the oxide.

Jan 1, 2005