Search Documents

By P. J. N. Pells

A good thing is becoming a bad thing. Rock mass classification systems, that are so excellent for communications between engineers and geologists, and that can be valuable in categorizing project experience, are emasculating engineering geology and rock mechanics. Some engineering geologists have been sucked into thinking that Q and RMR values are all that is needed for engineering purposes, and seem to have put aside what can be learned from structural geology and geomorphology. Many rock mechanics engineers seem to have forgotten the scientific method. This paper attempts to redress the situation by showing how mechanics can be used in rock engineering to design with a similar rigour to that used in the fields of structural engineering, hydraulics and soil mechanics. It also attempts to remind practitioners of what can be achieved by skilled engineering geology.

Jan 1, 2008

By P. Wittke-Gatterman

ABSTRACT: A three dimensional constitutive law for swelling rock is presented. It can be applied to the osmotic swelling of mudstone as well as to the swelling of rocks containing anhydrite. It describes the development of time-dependent strains and stresses due to swelling considering elastic and viskoplastic behaviour. Furthermore an anisotropic swelling behaviour can be considered. This constitutive model was implemented within a numerical computation program according to the finite element method and calibrated on the basis of the results of measurements in the investigation drift of the Freudenstein tunnel which is completely located in the unleached Gypsum Keuper. A parameter combination could be found which results in a good agreement between numerical solutions and results of measurements. Therewith an analysis procedure which enables the design of tunnels in swelling rock is available. ZUSAMMENFASSUNG: Im vorliegenden Beitrag wird ein dreidimensionales Quellgesetz vorgestellt, das nach derzeitigem Kenntnisstand sowohl auf das osmotische Quellen von Tonsteinen als auch auf das Quellen anhydrithaltiger Ton- beziehungsweise Schluffsteine anwendbar ist. Das Stoffgesetz wurde in ein Finite-Elemente-Programm implementiert und anhand von Meßergebnissen des im unausgelaugten Gipskeuper liegenden Untersuchungsstollens des Freudensteintunnels kalibriert. Es ist gelungen, eine Kennwertkombination zu finden, mit der alle Meßergebnisse gut beschrieben werden können. Damit steht ein Bemessungsverfahren für Tunnel in quellfähigem Gebirge zur Verfügung. RÉSUMÉ: Dans l'article présent un loi de gonflement à trois dimensions est présenté, qui peut être appliqué aussi bien au gonflement osmotique de l'argile compactée q'au gonflement de l'argile compactée ou du limon compacté contenant de l'anhydrite. Le loi de comportement était implémenté dans un programme numérique d'éléments finis et calibré avec des résultats de mesures de la galerie de recherche du tunnel de Freudenstein, situé dans le Keuper de gypse non lessivé. On est réussi à trouver une combinaison de paramètres avec laquelle tous les résultats de mesures peuvent être bien décrits. Par ce moyen, une méthode de dimensionnement existe pour des tunnels dans de la roche capable de gonfler.

Jan 1, 2003

By C. J. Pretorius

More than 30 percent of the global demand for zircon (ZrSi04) is supplied by South Africa. A significant amount of the zircon is exported, and beneficiated products are then imported for industrial applications locally. Beneficiating the zircon locally could have a positive impact on the local market, since zircon is only one of many such cases. Ammonium acid fluoride serves as an alternative anhydrous fluorinating agent for zircon in the synthesis of several metal fluorides1,2. It provides an effective dry fluorinating method and is easier to handle than hydrogen fluoride or fluorine gas. Zircon exposed to extreme plasma temperatures dissociates and becomes more reactive. The reaction of the plasma-dissociated zircon (Zr02.SiO2) with the ammonium acid fluoride (NH4F.XHF, where x= 1 to 5) forms two main intermediate compounds (NH4)3ZrFr(s) and (NH4) 2SiF6(s), the latter decomposing to form volatile products at relatively low temperatures, providing easy separation of the silicon and zirconium compounds. The ammonium zirconate compound decomposes to form zirconium tetrafluoride (ZrF4), which can be further manufactured into zirconium metal, to name but one product. Data on the kinetics of the reaction of ammonium acid fluoride with zircon and plasma-dissociated zircon, combined with the thermo¬dynamic parameters of the reaction, is essential for the development of an industrial process for the production of a precursor for the manufacturing of zirconium metal, namely anhydrous ZrF4. Both the reaction kinetics and reaction parameters will be included in this study, as well as some proof that the reaction proceeds to ZrF4 on a small batch scale. If the exact reaction parameters can be pinned down, a wide spectrum of anhydrous metal fluorides can be synthesized through this fluorination route.

Jan 1, 2012

By M. B. Fonseca

Risk quantification in grade-tonnage curves is critical for capital investment in mining projects and can be obtained through geostatistical simulations of orebodies. A practical difficulty may arise in multi-element deposits, as the joint modelling of the related attributes using the traditional co-simulation approaches is computationally intensive and may be impractical for use in the industrial environment. This paper presents the construction of risk-integrating grade-tonnage curves for a complex copper deposit in northern Brazil, by jointly simulating its key geochemical attributes of interest: Cu, Fe and K. The joint conditional simulation of these elements is based on Minimum/Maximum Autocorrelation Factors (MAF). MAF is an approach, based on principal components, that spatially decorrelates the variables involved to non-correlated factors. MAF’sspatial decorrelation at any lag distance is the main and critical difference of this approach from the principal component approach attempted in the past. In the MAF approach, the independent factors are individually simulated and back-transformed to the conditional simulations of the correlated deposit attributes that reproduce the cross-correlations of the original variables. Keywords: Joint simulation; mini/max autocorrelation factors; grade-tonnage curves.

Jan 1, 2003

By P. A. Lilly, W. Sarunic

In most cases, slope movement monitoring data are collected on a temporal basis and displacement or velocity is plotted against time in order to assist the engineer to make judgements about slope behaviour. Once an unusual behaviour pattern has been established, the data are then analysed to estimate when the key inflection points occur in the data, when the slope movements start to accelerate and, ultimately, when the slope is expected to collapse. The identification of these inflection points is sometimes difficult to achieve with the naked eye. This paper presents the application of a trend analysis technique, known as cusums, to assist in this process. The authors have presented a range of data from various real life examples which highlight the effectiveness of the cusums technique. A key aspect of the cusums technique is the use of a constant (K) against which data trends are assessed. This constant is best derived from slope performance data at each site, as each rock mass will behave in its own unique way. The authors have experienced slopes that have had threshold values ranging from 0.1mm/day through to 10mm/day, and therefore a conservative approach should be adopted when assessing the performance of slopes.

Jan 1, 2006

By I. W. van der Merwe

Recently, a new kind of filtration has emerged, namely nano-filtration (NF). It is a membrane-based process which exhibits totally unique separation characteristics for dissolved salts as well as for many non-charged species. By exploiting the particular separation characteristics of this new membrane type, many unique and novel separations have been made possible. The basis for separation by nanofiltration is the negative surface charge of the membrane. This results in rejection of multivalent anions, whilst associated cations are also rejected to maintain electro-neutrality. This peculiar property enables separation of dissolved ions such as sulphate and copper from acid, whilst the acid may be purified for reuse. This paper aims at providing an overview of the principles of nanofiltration, illustrated by particular examples.

Jan 1, 1998

By M. Abdellatif

Keywords: Pyrometallurgy, furnace, DC arc furnace, smelting, silicon The technical feasibility of silicon smelting in a DC arc furnace was investigated. A graphite-lined furnace was operated at power levels of 150 to 160 kW, and 40 to 60 V. The average feed rate during the silicon production period was about 30 kg/h. The recipe consisted of pre-mixed batches of 28% petroleum coke and 72% lumpy silica. The target furnace operating temperature was set at 1600°C and then raised to 1700°C. In total, about 1.6 tons of premixed feed materials was processed over 16 feeding?tapping operations. The feed was manually charged into the furnace in sub-batches of 10 to 40 kg at a time. The total batch mass was set at 90 kg during the initial part of the testwork, and increased to about 120 kg for the rest of the campaign.

Jan 1, 2011

By R. J. Hundermark

Keywords: Anglo American, Anglo Platinum Ltd, Waterval, Mortimer, Polokwane, ACP, pyrometallurgy, platinum, PGMs Anglo Platinum Ltd is the largest primary platinum producer in the world and operates three smelters in South Africa: Waterval, Mortimer and Polokwane. The operational details of the smelters are covered in previous reviews, thus only unit operations that have been upgraded are discussed. The most significant of the upgrades include the installation of a second ACP converter at Waterval Smelter in 2006 and the anticipated upgrade of Mortimer Smelter to 38MW in 2011. Several advances have been made in the smelting operations to improve the furnace stability and longevity. Control of the chromium input to each of the smelters has substantially allowed continued operations at levels below the spinel saturation point in slag, which results in lowered matte and slag temperatures. Mogalakwena concentrate, arising from the Platreef ore, is used to dilute high chromium-containing concentrates. In addition, furnace controls have improved in terms of crucible temperature and condition monitoring, improved feeding control, management of alarms and trips and having the quality of instrumentation and operational rigour required to support this. Advances have been made on the ACP converter in terms of good converter matte quality, and increased intensity and efficiency of operation. Combined with improvements to both the conventional and tower sulfuric acid plants, the emissions from Waterval Smelter have been reduced substantially since the introduction of the ACP. This is in spite of increasing metal throughput. The Anglo Platinum Ltd smelting operations have made significant progress since 2006 and further advances are envisaged to further improve on safety, reduce costs, increase efficiencies and throughput, while reducing emissions.

Jan 1, 2011

By T. Struminski

The paper is aimed to assess the possibilities of usage of pyrometers and thermal cameras to study ventilation and environmental conditions in underground mines. Surface and underground thermovision tests were carried out in the Rudna mine and included channels and diffusers of some selected fan stations, shaft crest closures, engines of central fans and their instrumentation. The thermovision underground tests in the Rudna mine consisted of ventilation barriers, underground fans, temperature of rocks, ventilation machines, parts of belt-conveyors and electric machinery.

Jan 1, 2003

By K. Coleman, C. Visser, N. Selby, X. W. Pan, T. Letwaba

A prototype weightometer soft sensor is under development at DebTech, De Beers in partnership with Venetia Mine. Its main function consists of an online data source; data validation; dynamic weightometer models; online detection of weightometer failure; alarming and replacing a weightometer when it fails. 31 dynamic models have been developed. All models with R2>= 85%are accepted as good models and they generally have satisfactory results with a daily error of less than 8% within 90% confidence level. By using those models, a set of soft sensors can be set up to cover all weightometers in the entire processes starting from primary crushing to the stock piles of dense medium separation (DMS). Some practical issues and concerns on model development are discussed, including data collection, data analysis, data pre-processing, variable selection, time delay, model training and model validation. When deploying the weightometer soft sensor system, the potential benefits could include: reduction in plant downtime; reduction in unplanned maintenance and even replacement of non-critical weightometers, particularly where nuclear weightometers are used. Keywords: soft sensor, weightometer, dynamic modelling, neural network modelling

Jan 1, 2003

By E. L. J. Kleynhans, J. I. J. Fick, J. P. Beukes, P. G. van Zyl

"Ferrochrome (FeCr) is vital for the production of stainless and high-alloy ferritic steels, since it is the only source of new Cr units. FeCr production is an energy-intensive process. The pelletized chromite prereduction process is most likely the FeCr production process with the lowest specific electricity consumption (SEC), i.e. MWh/t, currently in operation. However, due to increases in costs, efficiency, and environmental pressures, FeCr producers are attempting to lower their overall energy consumption even further. Recently, it was proven that pre-oxidation of chromite ore prior to pelletization and prereduction significantly decreases both the SEC and lumpy carbonaceous reductants required for smelting. This paper presents the first attempt at conceptualizing the technoeconomic feasibility of integrating chromite pre-oxidation into the prereduction process. Financial modelling yielded a net present value (NPV) at a 10% discount rate of approximately R900 million and an internal rate of return (IRR) of approximatelyy 30.5% after tax, suggesting that the implementation of pre-oxidation prior to pellet prereduction may be financially viable. Sensitivity analysis indicated that the parameter with the greatest influence on project NPV and IRR is the level of prereduction. This indicates that the relationship between maintaining the optimum pre-oxidation temperature and the degree of prereduction is critical for maximium process efficiency. IntroductionStainless steel is a crucial alloy in modern society. Virgin chromium (Cr) units used in the manufacturing of stainless steel are obtained from ferrochrome (FeCr) – a relatively crude alloy consisting predominantly of Cr and iron (Fe) (Murthy, Tripathy, and Kumar, 2011; Beukes, van Zyl, and Ras, 2012). FeCr is produced mainly by the carbothermic reduction of chromite ore in submerged arc furnaces (SAFs) and direct current arc furnaces (DCFs) (Neizel et al., 2013; Beukes, Dawson, and van Zyl, 2010; Dwarapudi et al., 2013). The energy required to heat, smelt, and reduce the chromite ore to the metallized state is supplied by electricity (Pan, 2013). FeCr production is an energy-intensive process, with a specific electricity consumption (SEC) varying from 2.4 MWh/t to more than 4.0 MWh/t FeCr produced, depending on the process applied (Pan, 2013; Neizel et al., 2013). Daavittila, Honkaniemi, and Jokinen (2004) stated that the typical operational costs of FeCr smelters can be divided into four categories, i.e. chromite ore (30%), carbonaceous reductant (20%), electricity (30%), and other production costs (20%). This makes electricity consumption the joint largest factor that influences operational costs in FeCr production."

Jan 1, 2017

By Q. G. Reynolds

Keywords: Pyrometallurgy, furnace, DC, reverse polarity, dual-electrode The dual-electrode direct current (DC) arc furnace uses two graphite electrodes, one connected as cathode, and one as anode. Such an arrangement avoids some of the design difficulties associated with the anode hearth traditionally used in single electrode and twin-cathode DC furnaces, but can introduce other design and operational difficulties including deflection of the arcs toward the furnace walls. Counter-intuitively, both arc jets in a dual-electrode furnace travel from the electrode down to the bath surface, despite carrying electric current in opposite directions ? this is suggested in the theory of the governing equations of arc formation, and confirmed by experiments using high-speed photography. The dual-electrode arc system at small pilot-plant scale is studied using a transient magneto-hydrodynamic model capable of predicting arc deflection and interaction from first principles, and the results are compared to the behaviour of twin-cathode systems at similar power. Finally, a simple arrangement of the furnace busbars, M configuration, is shown to provide some passive protection against arc deflection.

Jan 1, 2011

By B. Erdem

This article introduces a computer model, which emphasizes panel design for draglines deployed in direct side-casting mode. The study covers flat and inclined coal-seam conditions with the dragline operating along the strike-line. Two casting methods are embedded in the model: material is placed in the open set adjacent to the one on which the dragline is located (the DNS method) and material is placed in the open set adjacent to the one the dragline excavates (the DND method). While in the first method the unproductive walking time is reduced as the set is enlarged, in the second method the cycle time is lessened as the dragline swings along an acute angle. The side-casting model is shaped so as to provide several panel configurations instead of a single one to conform to the characteristics for an opencast mine. This is achieved by assigning the pit width an interval of values ranging from a minimum to a maximum. The model includes solutions to other critical design parameters such as: set length, swing angles at key cut and main cut positions, and required dragline reach at key cut and main cut positions. The model outcomes reveal the following: the stripping operation is largely affected when the coal-seam is inclined. The downhill spoiling mode should be applied wherever possible. The DNS pattern allows wider pit width intervals as well as longer sets and longer reaches.

Jan 1, 2004

By C. Kruger

Anglo American Platinum has adopted a strategy of best practice principles (BPP) for sampling, mass measurement, analysis, and metal accounting for more than a decade now. When new plants are designed, the most suitable sampling equipment and sampling protocols are implemented and material flows and plant layouts are designed around sampling strategies. A few years ago, a crushing plant for a high-grade matte stream was commissioned. The design called for the high-grade material to be crushed to 95% passing 2 mm, and the design allowed for a single-cutter primary Vezin sampler taking increments from a gravity flowing stream at regular intervals while filling a tanker for pneumatic offload at the base metal refinery. This was a single point of sampling and analysis that would measure the wanted output from the smelting complex and the input to the refineries. In addition, the design incorporated the functionality to collect increments in an ?interleaved? fashion from the Vezin sampler for internal precision checks. The metal accounting strategy for Anglo Platinum involves the ongoing measurement of all inputs, outputs, and stock levels for all operations for platinum group metal (PGM) and base metal (BM) content. Included are yearly stocktakes, usually done on 1 February, across the smelters and refineries (at least the base metal refinery). In the accounting period immediately following the introduction of the new crushing and sampling facility, a trend was developing whereby the absolute difference between the physical stock and theoretical stock (PGMs predominantly) increased for the two respective sites on an ongoing basis. The smelter showed an increase in physical stock compared to the theoretical stock (sender) and the base metal refinery showed an increase in theoretical stock against physical stock. Because of this anomaly, an additional stocktake was held in September for the period in question, and it was confirmed through the physical stock measurement results that the PGM accounting problem was indeed pointing towards the evaluation of the high-grade matte stream. This paper showcases parts of the process that took place to explain the poor accountabilities for the two sites. Previous results from the sampler ratification process (of the interleaved sampling design) were reanalysed, a physical inspection was carried out on the sampling system again, and the sampler performance was monitored (quality control parameters) for the period. From these investigations, it was found that airflows inside the Vezin introduced the sampling bias. A change in sampling protocol was introduced, as well as certain physical changes to the sampling equipment, to eliminate the airflow and thus the bias conditions significantly. The accounting period that followed the phased upgrading process showed that the accounting between the smelter and base metal refinery had been restored to within statistical limits (difference between physical and theoretical stock below 5% relative to theoretical stock). Keywords sampling, metal accounting, Vezin sampler, sampler bias.

Jan 1, 2014

By P. Share

As part of JAGUARS (JApanese-German Underground Acoustic emission Research in South Africa), high-resolution tiltmeters were installed during 2007 at Mponeng gold mine, South Africa, in an attempt to study and understand the risks posed by in-mine seismic events and to subsequently use the knowledge gained to mitigate these risks. In December 2007, an M2.2 event occurred at Mponeng and was detected by the tiltmeters installed. The tilt expected for the M2.2 event is modelled through the use of numerical and analytical tools and utilizing, as input parameters, characteristics of the event such as the rupture area, the amount of slip, elastic properties of the rock, the state of stress before the event occurred, and frictional parameters of the rupture. The calculated tilt values are correlated and compared with the recorded data, and are found to be of the same order. Certain input parameters, such as the initial rupture point, are further constrained by varying them, during modelling, until the calculated and observed tilt values are approximately equal. From modelling, it can be concluded that the rupture point had to be closer to the location of the tiltmeters. In addition, possible locations acting as source areas for the observed aftertilt are determined. Further modelling still needs to be done to quantify the effects of the tunnel close to the tiltmeters and plastic deformation of the rock mass. Keywords high-resolution tilt data, Mponeng gold mine, M 2.2 seismic event, analytical modeling, numerical modeling, rupture plane.

Oct 1, 2013

By B. Simser

At Brunswick Mine, an increase in the number of seismically-related falls of ground and in particular rockbursts occurred during 1999. This was due to the ever-increasing stress levels in the remaining ore reserves, mining in difficult highly stressed areas and in particular troublesome geological features. In conjunction with the Noranda Technology Centre, development of rockburst support systems started at the Brunswick Mine in 1996 and efforts were accelerated in 1999. A support package consisting of #6 gauge chain link mesh, #0 gauge heavy mesh straps, and a 1 m by 1 m pattern of modified conebolts was developed. The conebolts were modified to enable mixing of the resin anchoring. Two major rockbursts occurred during an intense seismic episode at the Brunswick Mine from October 13th to 17th , 2000.The area was evacuated approximately four hours before the first burst hit, and remained closed during the seismic ?flurry??. The first damaging activity occurred around midnight on Friday the 13th, and a second damaging episode occurred on the 17th that included a local Richter Magnitude 2.7 event. The second rockburst had dimensions of approximately 5 m by 5 m by 20 m or 2150 tonnes of massive sulphide material (density 4300 kg/m3). The first failure area was more extensive, caving approximately six metres of an intersection back with the lateral extent not safely measurable. This paper briefly describes the mining conditions that led to the bursting, the seismic response of the region, the mechanisms thought to have caused the bursts, and a yielding support system which had been partially installed before the burst.

Jan 1, 2002

By T. van Heerden

A range of supported gold catalysts was prepared by ion exchange, varying many of the preparation variables, including concentration in the precursor solution, washing procedure, as well as drying and calcination procedures. These catalysts have been characterized extensively. TEM images show essentially the same crystallite size distributions, between 2?5 nm, for almost all catalysts, the only exception being catalysts not washed in ammonia, which did not show any small crystallites. Additional characterization with SEM yielded an interesting discovery. Catalysts that appear identical on the TEM also contain some large crystallites in the range of 50?500 nm. Differences in dispersion due to the drying procedure not seen on the TEM can now be observed. Oxygen chemisorption is being investigated as an additional method to characterize gold based catalysts to complement the typically used electron microscope techniques.

Jan 1, 2012

By Chandrakala Kari, S. Mohan Rao, Gajanan Kapure, K. S. Raju

High carbon ferrochrome production process is energy intensive, consumes approximately 3300-3400 kWh per ton of metal produced. This amounts to ~ 34% of the total ferrochrome production cost. The power costs in India are almost 4 times greater than the leading ferrochrome producing countries like South Africa. Hence there is a need to look for alternative sources of energy. In ferrochrome making process large volumes of high concentration CO gas (~ 85%V) is developed at ~400-5000C, which if combusted within furnace represents high potential for significant electrical energy savings. In a typical heat in the state-of-the-art submerged arc furnace, about 34 kmol of CO gas is generated per ton of ferrochrome metal, which, if post combusted to CO2, represents 7620 MJ of energy. Post combustion of the evolving CO (and H2) gas to CO2 can be achieved by providing additional oxygen before the generated CO gas leaves the furnace. In this paper, a concept of post combustion in submerged arc furnace as potential source of significant electrical energy saving in ferro-chrome making process has been explored. The prospects and limitations of the same are discussed. The value of this paper lies in its attempt to explore the post combustion application to submerged arc furnace with an objective of significant reduction in electrical energy consumption in ferrochrome production process.

Jan 1, 2007

It is estimated that the tailings dam of the Mouteh Gold Mine, in Iran, contains more than 770 kg of gold. Microscopic analysis reveals that sulphide minerals and active carbon are the main sources of the gold in the tailings residue. Flotation and cyanidation tests on the samples of tailings were conducted. Flotation concentrates, containing around 87.79% of the gold, which were associated with sulphide minerals, were recovered. By regrinding, roasting, and cyanidation of the flotation concentrate, the gold dissolution recovery was in the range of 87.8 to 98.4%. The carbon-in-column method was used to recover 98% of the gold from the solution. Keywords: gold ore, pyrite, flotation, roasting, cyanidation

Jan 1, 2009

By B. S. Xakalashe

Keywords: Pyrometallurgy, silicon, solar cells Silicon has been the dominant material in the photovoltaic (PV) industry since its application in the space industry in 1958. This review focuses on crystalline silicon solar cells, primarily due to their dominance in the photovoltaic industry, omitting other photovoltaic cell technologies such as second generation (e.g. thin films) and third generation (e.g. nano-structured solar cells). The value chain for the production of crystalline silicon solar cells has been reviewed. The primary processing steps for the production of silicon solar cells from quartz are as follows: bulk production of metallurgical-grade silicon via carbothermic reduction in a submerged furnace, refining of metallurgical-grade silicon via the chemical means to polycrystalline silicon, or through the metallurgical route to solar-grade silicon, wafer manufacturing, and, lastly, silicon solar cell manufacturing. During downstream processing, solar cells are interconnected and encapsulated into solar modules (panels), which can be used individually or incorporated into a photovoltaic system for electricity generation and supply. The cost for crystalline silicon based solar cells is approaching one US dollar per watt peak ($1/Wp), while the most cost-effective solar modules in industry have reported costs below $1/Wp, and are based on CdTe thin films. Solar cell energy conversion efficiencies as high as 22% have been reported in industry for crystalline silicon solar cells.

Jan 1, 2011