Search Documents

By A. Rejeb

ABSTRACT: This paper contributes to the study of underground structures in argillaceous media, especially Tournemire argillites (Aveyron, France). The basic results obtained over six years in two experimental drifts at the Tournemire site are presented. In situ measurements cover drift wall temperature, humidity and convergence. Delayed convergence represents around 50-65% of the total measured convergence. Analysis of the measurements has shown that delayed convergence is explained by the viscoplastic behaviour of the argillaceous formations. Lemaitre’s rheological model has been extended to the orthotropic case, as Tournemire argillite is naturally anisotropic. The triaxial creep test results on samples at different orientations enabled the parameters of the Tournemire argillite to be identified in terms of orthotropic viscoplastic law. A plane deformation model, using this rheological law and the initial stress field in the site, was developed to interpret the convergence measurements in the drifts. The computed results match the measurements well, especially during the excavation phase. KEY WORDS: Argillite, convergence, time-dependent behaviour, creep, viscoplasticity, modelling. ZUSAMMENFASSUNG: Der vorliegende Artikel ist ein Beitrag zur Untersuchung der unterirdischen Strukturen tonhaltiger Milieus, insbesondere der Tongesteine von Tournemire (Aveyron, Frankreich). Die wichtigsten Ergebnisse, die in zwei Forschungsstrecken am Standort Tournemine über einen Beobachtungszeitraum von sechs Jahren zusammengetragen wurden, werden hier vorgestellt. Gemessen wurden in situ Temperatur, Feuchtigkeit und Streckenkonvergenz. Von der insgesamt gemessenen Konvergenz sind etwa 50 bis 65 % auf zeitlich verzögerte Konvergenz zurückzuführen. Die Auswertung aller Messungen hat ergeben, dass die zeitverzögerte Konvergenz mit dem viskos-plastischen Verhalten des Tonsteinmassivs zu erklären ist. Aufgrund der naturgemäßen Anisotropie des Tongesteins von Tournemine wurde das rheologische Modell von Lemaitre auf den orthotropen Fall ausgedehnt. Triaxiale Kriechversuche bei jeweils unterschiedlicher Ausrichtung dienten der Ermittlung der einzelnen Parameter des orthotropen, viskos-plastischen Gesetzes. Zur Auswertung der Konvergenzmessungen innerhalb der beiden Strecken wurde unter Beachtung dieses rheologischen Modells sowie des ursprünglichen Spannungszustands vor Ort ein flächiges Deformationsmodell entwickelt. Die Rechenergebnisse zeigen eine gute Übereinstimmung mit den Messungen, insbesondere während der Vortriebsphase. SCHLÜSSELWÖRTER: Tongestein, Konvergenz, zeitlich verzögertes Verhalten, Kriechen, Viskoplastizität, Modellbildung. RESUME : Cet article est une contribution à l’étude des structures souterraines dans les milieux argileux, notamment les argilites de Tournemire (Aveyron, France). Les principaux résultats obtenus pendant six années, dans deux galeries d’expérimentation au site de Tournemire, sont présentés. Ces mesures portent sur la température, l’humidité et la convergence des parements des galeries. La convergence différée représente environ 50 à 65% de la convergence totale mesurée. L’analyse de l’ensemble des mesures a montré que la convergence différée est interprétée par le comportement viscoplastique du massif argileux. Etant donné que l’argilite de Tournemire est naturellement anisotrope, le modèle rhéologique de Lemaitre a été étendu au cas orthotrope. Les résultats des essais de fluage triaxial, sur des échantillons à différentes orientations, ont permis de déterminer les paramètres de la loi viscoplastique orthotrope. Un modèle en déformation plane, utilisant cette loi rhéologique et l’état de contrainte initiale dans le site, a été développé en vue d’interpréter les mesures de convergence dans les galeries. Les résultats des calculs sont en bon accord avec les mesures et plus particulièrement durant la phase de creusement. MOTS-CLEFS : argilite, convergence, comportement différé, fluage, viscoplasticité, modélisation.

Jan 1, 2003

Orange Free State Branch Minutes of a Committee Meeting held in the Boardroom of Western Holdings on Thursday, IIth October, 1973, at 5.00 p.m. Present Messrs E. T. Wilson (in the Chair), E. Dunstan, W. B. Evans, C. J. Isaac, C. Mostert, N. Shand, R. Williams, and G. Young.

Jan 2, 1974

By M. Olper

The zinc recycling is assuming more and more importance. A lot of zinc secondaries and wastes are ready to be collected and converted to zinc metal. The impurities present in these materials and the technical and economical problems that some traditional ways of treating these materials are facing, call for new technologies. The EZINEX Process, a fully hydrometallurgical process industrially proven to convert oxidised zinc bearing materials directly to zinc cathodes, is an innovative process that can deal with any kind of zinc waste/secondaries in a very powerful way. In this paper the highlights of this process will be shown and discussed to demonstrate the robustness of the process and its economic viability.

Jan 1, 2008

This publication is provided on an "as is" basis without warranties of any kind, either expressed or implied including, but not limited to warranties of title or implied warranties of merchantability of fitness for a particular purpose. The information contained in this publication is for general information purposes only. It does not constitute professional, technical, financial or other advice to the user of this publication and must not be relied upon as such by any person whatsoever. The use of this publication is at the users own risk. The authors/creators of the information contained in this publication have tried to ensure that the information contained herein is correct, but errors or inaccuracies may exist or the information may be incomplete, unreliable or no longer up to date. Therefore, no warranties of any nature whatsoever are given and any liability to any person in respect of anything and in respect of the consequences of anything done or omitted to be done, wholly or partly in reliance upon the whole or any part hereof, are disclaimed, including and without limitation any contractual, dialectal, direct, consequential or financial damages or losses. On no account will Organisers and/or any of the contributors or any person or entity involved in creating, producing or distributing the information and or software available in this publication be liable for any such damages arising out of the use of or inability to use this publication. Copyright Reserved The South African Institute of Mining and Metallurgy P O Box 61127, Marshalltown 2107, South Africa www.saimm.co.za All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical photocopying, recording or otherwise without the written permission of the copyright owner. Although the greatest care has been taken in the compilation of the entire contents, the editors and publishers do not accept responsibility for errors or omissions. First Edition Copyright February 2004 Proceedings ISBN: 0-9584663-5-1 (1 volume and CD-ROM)

Jan 1, 2004

By M. D. Dolan

In this study, the development of a new method for investigating the diffusion of metal cations in multi-component slag systems, using microprobe analysis is discussed. This method allows the analysis of the diffusion of multiple species within a single system. This project has focused on the diffusion characteristics of manganese, iron, calcium and silicon in silicate slags, in order to simulate industrial steel and ferromanganese production. The diffusion behaviour of transition metals is of particular interest because of the effects of their variable valence. This study identified the variation in diffusivity of slag components with changes in composition and temperature of multi-component slag systems. The molecular structure of the experimental calcium-aluminosilicate slags was investigated to determine the chemical and physical properties that influence diffusion behaviour. This experimental data was used to develop predictive models for diffusivity. These models enable the estimation of the diffusivity of many slag components in complex slags, over a range of compositions.

Jan 1, 2004

By E. Chen, M. Barati, K. Coley

The reaction between carbon and slags is of significant importance in direct smelting of iron ores, EAF slag foaming and copper slag cleaning processes. This reaction is known to occur via gaseous intermediates and it is important to have fundamental data to understand the relative importance of each reaction step. In this study, the rate of CO2dissociation on different slag surfaces is measured using an isotope exchange technique. It was found that increasing iron oxide content up to 30 wt per cent does not have a significant effect on the rate constant while increasing from this limit, increases the rate constant dramatically. Activation energy of CO2dissociation on slags of unit basicity and different iron oxide contents is in the range of 180±40 kJ/mol. It is found that rate constant dependence on oxygen potential in the slag phase is increasing with iron oxide concentration. In the case of copper making slags, the influence of copper oxide is found to increase the magnitude of apparent rate constant, while decreasing the activation energy considerably. Key words: Gas-slag reaction, CO2dissociation, copper slag, kinetics, isotope exchange

Jan 1, 2004

By B. R. Broekman, K. J. R. Ford

Over the last decade significant development and use has been made of a simulation model that describes the HCFeMn smelting operations in Assmang Ltd. This spreadsheet based, semi-empirical, predictive model is derived from data from the submerged arc furnaces at Assmang?s Cato Ridge, KwaZulu-Natal smelter site. Departures from the empirical base case mass balance due to changes in the ores, reductant feeds and operating parameters are accounted for by use of fundamental relationships and heuristic type ratios which are applied in an iterative manner in the model. The model performs a sequential set of calculations to iteratively converge on a fully consistent mass and energy balance solution, which predicts Mn alloy and slag output masses and compositions for a given set of feeds. 440 MWh per operating day is used as the basis of energy input. The paper describes the key model components, assumptions made and calculation approach. Added to the mass and energy balance is a cost and revenue balance, which allows prediction of the economic performance for each simulation. Substantial use of the model has been made in simulating the performance of the current Assmang HCFeMn furnaces for both smelter investigations and future production planning. The model has also been a valuable tool in the strategic analysis of the use of future Mn ores and has formed the vital link between mine ore grades (metal and slag elements) and the expected alloy output, grade and profitability. Additionally, the model has been used in benchmarking exercises to predict other Mn smelting operations with remarkable accuracy. The paper highlights some aspects of the approaches taken in using the model to benchmark Assmang?s own furnace performance and cost competitiveness with other producers. For Assmang the development and application of this modelling technology has led to transformation in understanding of the Assmang HCFeMn furnace operations and increased awareness of the potential of its Mn ore bodies.

Jan 1, 2004

By K. M. Godiwalla, S. Ranganathan

The thermal state in submerged-arc furnaces (S.A.F.) producing ferro alloys is important for the conditions of both the grade of alloy produced as well as specific energy consumption. The temperature profile in the S.A.F. is affected by the endothermic chemical reactions and the rate of gas evolution. The gas evolution commences at about 900 C due to the reduction of iron in the ore. A first-principle-based 2-D model has been developed to predict the temperature profile in the furnace. In this study, four ores of different grades have been considered in order to simulate the thermal profile in the S.A.F. The influence of the composition of the ore on the thermal profile and its significance in rationalisation of charge distribution to optimise the process are discussed.

Jan 1, 2007

By D. Grgic, A. Giraud, F. Homand

RESUME : Le comportement mécanique partiellement saturé du minerai de fer a été étudié à partir d’essais de compression simple sur des éprouvettes à pression capillaire imposée par les solutions salines. Les échantillons restent peu saturés (32 %) même pour une humidité relative de 94 %, du fait de la présence de mésopores. Jusqu’à 90 % d’humidité relative la résistance diminue régulièrement. De 90 % à 94 % une forte chute est observée et pourrait être liée à la fois aux effets capillaires et à l’hydratation de certains minéraux. Le cycle hydrique subit par la roche dans la mine a été modélisé en 1D à l’aide d’un code de calcul entièrement couplé pour les milieux poreux partiellement saturés. Les calculs ont montré notamment une diminution importante en paroi des contraintes totales au cours de la phase de désaturation et une augmentation importante au cours de la phase de resaturation. Ces variations pourraient induire un endommagement du massif et être à l’origine d’instabilités, et soulignent l’intérêt d’une modélisation avec une géométrie plus adaptée. MOTS-CLEFS : mines de fer, partiellement saturé, pression capillaire, résistance, modélisation. ABSTRACT : The partially saturated mechanical behavior of iron ore has been studied from uniaxial compression tests on samples in which the suction is imposed with aqueous solutions. Samples are little saturated (32 %) even for a 94 % relative humidity because pores are too large. Up to 90 % relative humidity the strength decreases regularly. From 90 % to 94 % a great decrease is observed ; it could be explained by the capillary effects and the moisturizing of some minerals. The hydrous cycle imposed to the rocks in the mine has been modeled with an 1D fully coupled code for partially saturated porous media. The computations have shown an important decrease in the total stresses at the wall during the desaturation stage and an important increase during the re-saturation stage. These variations could induce a rock mass damage and instabilities, and highlight the necessity of a modeling with a well-adapted geometry. KEY-WORDS : iron mines, partially saturated, suction, strength, modeling. ZUSAMMENFASSUNG : Das mechanische Verhalten von teilweise gesättigten Eisenerz wird durch einachsige Druckversuche untergesucht. Die Prüfkörper haben einen durch Salzlösungen gestimmten kapillarischen Druck. Sie bleiben kaum gesättigt (32 %), sogar bei einer relativen Feuchtigkeit von 94 %, aufgrund der Anwesenheit von Mesoporen. Bis eine relative Feuchtigkeit von 90 % verringert sich gleichmässig die Druckfestigkeit und zwischen 90 % und 94 % merkt man eine starke Abnahme in Verbindung, möglicherweise, mit kapillarischen Effekten und Hydratation von bestimmten Mineralen. Die nümerische 1D Modellisierung des gezwungenen Wasserzyklus im Stein der Mine ist mit einem für porösen Medien ganz vernetzten Rechnungcode geführt. Sie zeigt besonders ein bedeutendes Sinken der Gesamtspannung während der Entwässerung und eine bedeutende Steigerung während der Sättigung. Diese Veränderungen könnten die Beschädigung des Gesteines herbeiführen und die Grundlage von Unstabilität sein. Sie unterstreichen die Wichtigkeit eine Modellisierung mit einer gut geeigneten Geometrie. STICHWÖRTER : Eisenminen, teilweise gesättigt, kapillarischer Druck, Druckfestigkeit, Modellisierung.

Jan 1, 2003

By J. Gómez-Hernández, P. K. Kaiser

Abstract The process of stress-induced fracturing around underground excavations in brittle rock is associated with dilation or volume increase of the failed, fractured rock. Different attempts to account analytically for this dilation have been made within the framework of plasticity theory. This theory has been developed mostly for metals, strain-hardening materials or soils, but brittle failure of rock-like materials is characterized by strain-softening behaviour and the volume change is dominated by geometric factors, which may violate stability principles of plasticity. In this work a semi-empirical Rock Mass Bulking Model (RMBM) was developed, using as starting concepts: dilation angle, plastic strain rates, effective deformation modulus, effective Poisson's ratio, Griffith locus, and the definition of a bulking factor BF introduced by Kaiser et al. (1996). The model was calibrated in order to obtain bulking factors that are consistent with experimental data and case studies of measured bulking around underground excavations. Résumé La fracturation provoquée par le stress autour des excavations souterraines dans le minéral friable est associée à la dilatation ou à l’augmentation du volume de la roche en rupture. Dans le cadre de la théorie de la plasticité, différents essais ont été faits dans le but de trouver une justification analytique pour cette dilatation. Cette théorie a d’abord été élaborée pour les métaux, les matériaux ou les sols d’écrouissage, mais la rupture fragile de matériaux d’aspect rocheux est caractérisée par un comportement d’amollissement et le changement de volume est dominé par des facteurs géométriques, ce qui pourrait ne pas être conforme aux principes de stabilité de la plasticité. Dans le présent ouvrage, un Modèle semi-empirique de masse rocheuse a été élaboré, dont les concepts initiaux sont les suivants : angle de dilatation, vitesse de fluage plastique, module effectif de déformation, coefficient effectif de Poisson, locus de Griffith, et la définition d’un facteur de foisonnement FF apportée par Kaiser et al. (1996). Le modèle a été calibré afin d’obtenir des facteurs de foisonnement qui soient conformes aux données expérimentales et aux études de cas sur le foisonnement mesuré autour des excavations souterraines. Kurzfassung Der Prozess von Brüchen in unterirdischen Abgrabungen in sprödem Gestein ist mit der Ausweitung oder der Volumenzunahme des gebrochenen Gesteins verbunden. Verschiedene Versuche im Rahmen der Verformbarkeitstheorie haben versucht, diese Ausweitung analytisch festzustellen. Die Verformbarkeitstheorie wurde hauptsächlich für Metalle, kalthärtende Werkstoffe oder Böden entwickelt, da sprödes Versagen von Gestein ähnlichen Werkstoffen von kaltenhärtendem Materialverhalten gekennzeichtnet ist, und die Volumenveränderung von geometrischen Faktoren beherrscht wird, die die Stabilitätsprinzipien der Plastizität übertreten. In dieser Arbeit wurde ein halbempirisches Rock Mass Bulking Model (RMBM) (Modell für das Aufgehen der Gesteinsmasse), entwickelt, für das die folgenden Anfangsprinzipien benutzt wurden: Ausweitungswinkel, plastische Fliessensätze, wirksames Verformungsmodul, leistungsfähiges Poissons Verhältnis, die Griffith Ortskurve und die Bestimmung eines Aufgehensfaktor BF1 der von Kaiser et al. (1996) eingefürt wurde. Das Modell wurde so kalibriert, dass es die Aufgehenfaktoren erzielte, die mit den Vesuchsangaben und den Fallstudien von Aufgehensmessungen in unterirdischen Abgrabungen übereinstimmen.

Jan 1, 2003

By Swapan Ghosh, Amitava Sengupta, Proloy Das

Ferro-alloys are very important ingredients used for making of quality steel with desired composition. In view of high demand in various types of ferro-alloys, it has become necessary to produce the same efficiently, safely and cost-effectively with consistent quality maintaining the anti-pollution norms. To achieve this goal, it is necessary to adopt latest process/equipment with the state-of-the-art instrumentation and automation system. A Programmable Logic Controller (PLC) based automation system with suitable Human Machine Interface(HMI) terminals along with intelligent field mounted sensing/control devices allows to monitor and control the complete plant effectively with optimum deployment of man-power. In association with this, use of process optimization controllers enables to achieve specialised functionalities of the submerged arc furnaces like material management, lining management, electrode management, power management, overall production management etc.

Jan 1, 2007

By Phillip J. Mackey, Rodney T. Jones

"Copper and copper alloys remain key materials for society today, with important uses found in the electrical, transportation, and construction industries. Copper demand is rising, with projections indicating that by 2025 global refined copper demand will increase to 29.5 million tons, up from the 22.4 million tons anticipated for 2015. This will require the opening up of dozens of new mines and numerous new smelters over this time period. Fortunately, Africa has significant reserves of copper, and African copper can once again play a key role in contributing to meeting the rising global demand for copper. This paper provides a brief overview of the current copper smelting operations in Southern Africa. INTRODUCTION Copper and copper alloys are essential materials for today’s modern world. The familiar green copper patina colour seen on buildings and other structures sometimes belies its true “green” characteristic – copper is essential for key emerging technologies such as wind turbines, tidal generating systems, solar energy systems, electric cars and the like. Consequently, it is believed that there will be continued growth in copper demand in the years ahead. Projections indicate that by 2025, as an example, global refined copper demand will increase to 29.5 million metric tons, up from the 22.4 million ton level anticipated for 2015. This will require dozens of new mines, and of the order of the equivalent of 10 to 12 new 0.5 million tons of copper/year-sized copper smelters (after factoring projected copper produced by electrowinning (EW))—overall, a huge undertaking. Fortunately, Africa has significant reserves of copper, and African copper can once again play a key role in supplying this rising global demand for copper. Africa’s share of global mined copper production was about 10% in 2014; however this will increase significantly in future if announced new projects eventuate. Southern Africa has an important role to play in this process. The present paper provides a brief overview of copper smelting in Southern Africa."

Jan 1, 2015

By Manoj Kumar, S. Ranganathan, S. N. Sinha

The reducibility of three different manganese ores with coke was studied. The three ores were reduced to different extents under the same experimental conditions. The investigations showed that in the temperature range of 900-1000 ×C, Fe2O3 in the ore was reduced to metallic iron. MnO2 was reduced to Mn3O4 in all cases except one in which it was reduced to Mn2O3. The kinetics of reduction was controlled by different mechanisms in the different ores. Temperature had a significant influence on the reducibility of the ores.

Jan 1, 2007

By C. Steve

ABSTRACT: In this paper, the stability evaluation and bifurcation criteria are presented for the Jinping arch dam structure. The bifurcation models in failure status of the arch dam are derived from the uniqueness of the controlling equation of dam behaviours, and the relative phenomena between positive definition of dam structural tangent stiffness and bifurcation are given in the paper. Then the structural collapse criteria for arch dam are discussed based on the energy mode. A stability criterion of dam based on the connection of yield zones is proposed according to the implementation of elasto-plastic FEM (finite element method) numerical analysis. In accordance with this judging method, nonlinear FEM analysis is used for Jinping arch dam. The failure process of the Jinping dam was simulated and yield zones were found under the overloading condition. Keywords: Stability evaluation, bifurcation, failure process, Jinping arch dam ZUSAMMENFASSUNG: In der Verliegenden Arbeit wird ein integrater geomechanisch Modellversuch fuer Jinping Bogenstaumauer Vorgesstellt. Die Bogenstaumauer liegt aut der komplizerten felsformationen. Der Zerstoerungsmechanismus, die Stabilitaetsfaktoren und die Interaktion zwischen der Bogenstaumauer und den Seiltichen. In der Vorliegenden Arbeit wird eine dreidimensionale finite element analyse fuer die seitlichen. Gestein sauflager mittels dem Bruchmodell Vorgestellt, da fuer Jiniping Bogenstaumauer angewandet wird. Ein Bruch mechanismus model einschliesslich der statistischen parameter der Gesteinfes tigkeit wird entauckeit. RÉSUMÉ: Das ce documènt a été faite une analyse d’elemt limité de trois dimensions dn fondement de construction de roche faisant appel au modéle de l’endommagemnet à fracture, analyse appliquée an fondement du bar ragevoute de Jinping. Ce documènt décrit le test de modéle géomecanique intégral pour le barrage-voûte de Jinping L’ampleur du modéle en question constitute l’une de plus importantes en China. Ils correspondent par faitement anx calculs des résultats.

Jan 1, 2003

By A. Pellegrino, F. Collin, C. Guiducci, R. Charlier

A numerical approach for modeling coupled Hydro-Mechanical fracture behavior in 2D is presented in this paper. This approach accounts for the strong dependence of the flow characteristics on fracture apertures and offers an anisotropic description of the flow propagation in the fracture. An interface finite element and a constitutive model are developed . In order to validate the applicability of the model to general geomechanic problems, 2D simulations were performed. Results show the good application of the mathematical model and the fundamental hydraulic role played by the fractures. In diesem Beitrag wird ein Stoffgesetz vorgeschlagen um hydromechanisches Kluftverhalten numerisch zu Modellieren. Dieser Vorgang nimmt die starke Abhängigkeit der Fliesseigenschaften von der Kluftöffnung mit in Anbetracht. Ein Interfaceelement und ein Stoffgesetz wurden entwickelt. Zum validieren der Anwendbarkeit dieses Modells wurden 2D Simulationen durchgeführt. Ergebnisse haben gezeigt dass das mathematische Model anwendbar ist und dass Klüfte eine fundamentale hydraulische Rolle spielen. Une approche numérique pour la modélisation du comportement couplé hydro-mécanique des fractures en 2D est présentée dans ce papier. Cette approche prend en compte la forte dépendance des caractéristiques du flux de fluide sur les ouvertures des fractures et présente une description anisotrope de la propagation du flux dans la fracture. Un élément fini d'interface et un modèle constitutif sont développés. Dans le but de valider l'applicabilité du modèle à des problèmes généraux de géomécanique, des simulations 2D ont été réalisées. Les résultats montrent la bonne application du modèle mathématique et le rôle hydraulique fondamental joué par les fractures.

Jan 1, 2003

By E. R. Davis, R. J. Knott

The paper discusses some of the tools of management in the field of project control, especially in engineering. Project control includes planning and cost engineering, and involves various phases: the conceptual Design and Planning Phase, the Definitive Design and Capital Budgeting Phase, and the Implementation Phase. Each of these phases is discussed in in, together with the use that can be made of data banks, progress reports, and computer systems.

Jan 1, 1982

By W. P. Nel

The introduction of the Higher Education Qualifications Framework (HEQF) and the updated Higher Education Qualifications Sub-Framework (HEQSF) has caused many South African university departments to rethink their programme qualification mixes (PQMs). In addition to the requirements stated in the HEQSF, a number of other factors have to be taken into consideration by a university department. These factors include, for example, the standards generated by the Engineering Standards Generating Body (ESGB) and subsequently approved by the Engineering Council of SA (ECSA) and the need to prepare students for various categories of professional registration with ECSA. This means that a university department has to choose the correct mix of Learning Programmes (LPs) from the HEQSF menu (which consists of 13 types of LPs). Preparing students for ECSA registration is aligned with the mission of universities, which is to teach and undertake research. However, research and the LPs associated with research go beyond the requirements for current ECSA registration. Assuming that universities offering engineering LPs would elect to prepare students for both ECSA registration and teach them to produce research outputs, which is mostly done at Master and Doctorate levels (NQF Levels 9 and 10), then it follows that academics are more interested in NQF Level 5 to 10 pathways (abbreviated as ?L5-10?) rather than the shorter pathways required towards professional registration. (For example, ECSA requires an NQF L5-L7 pathway for registration as a candidate professional technologist. This specific pathway may consist, for example, of two LPs, namely the 360-credit Diploma and the Advanced Diploma.) A L5-L10 pathway is a combination of LPs that will prepare the learner with a NSC (or equivalent qualification at level 4) to Doctoral level (level 10). Universities may choose at least four major pathways from the HEQSF menu in order to educate and develop students from NQF Level 5 to 10. However, various pathways towards registration in the category of candidate with ECSA are also embedded into these four NQF L5-L10 pathways, where each consist of a unique combination of LPs. Each of these pathways has an opportunity cost, and economic reality means that smaller departments may have to choose between the four pathways. Of all the many factors involved in PQM decision-making, the focus of this paper is on the HEQSF requirements, ECSA standards, and ECSA registration and how these, together with the various qualifications and educational LPs provided for by the HEQSF may impact on the PQM decision taken by engineering departments and schools at South African universities. The proposed four NQF L5-L10 ?pathway tool? for PQM decision-making may be useful for pointing out the advantages, disadvantages, and applications of the various pathways and combinations of pathways. Rather than deciding from a menu of thirteen qualifications and associated LPs, this article proposes that decision-making be undertaken on the basis of a menu of four main articulated ?NQF L5-L10? pathways (which also include one or more of the ECSA?s pathways for professional registration). The proposed ?NQF L5-L10 pathway? tool is an attempt to move one step closer to the aim of achieving a structured decision-making approach for designing a PQM at departmental level.

Jan 1, 2014

By Deon van Tonder, Bert Van Hege

Comparison of various technologies for uranium recovery from sulphuric acid leach solutions shows that Resin-in-Pulp (RIP) and/or Solvent extraction (SX) based processing routes are usually cost effective (11). A combined RIP-SX recovery-purification route and a CCD-SX recovery-purification route were investigated and optimised. The design basis used for the investigation was a production rate of 200 kg/h U3O8 over a solution concentration range of 40 to 1500 mg/L U3O8. The OPEX for the RIP-SX processing route was found to be sensitive to the variation in uranium concentration in the leach liquor. One of the main drivers for this trend is the leach acid concentration. Conversely, the CAPEX of the CCD-SX processing route was sensitive to the uranium concentration in the leach liquor. The leach acid concentration only affected the OPEX of the CCD-SX processing route modestly, as the bulk of the acid is recovered in a pre-leach circuit. Contrary to expectation, the effect of extractant loss assumptions on the overall processing route economics was found to be modest to insignificant. It should be noted that the CCD-SX processing route OPEX was more sensitive to extractant loss assumptions than the RIP-SX processing route OPEX. Economic optimum wash ratios were determined for the CCD-SX processing route and increased with leach concentration ? the increase in wash ratio was less than proportional. A 5-stage CCD configuration was found optimal over the concentration range investigated.

Jan 1, 2007

By D. Fukahori, K. Sugawara, A. Sato

X-ray Computed Tomography (CT) is a nondestructive imaging technique, and its efficiency is widely recognized. In the present paper, X-ray CT is successfully applied for the visualization of water permeation process in rock. A new experimental technique using a tracer, which mainly consists of Potassium Iodide (KI), is proposed, together with the analysis method of the velocity field. The permeation process and the velocity field in rock are concretely visualized and analyzed by considering the conservation of mass of the tracers. La tomographie calculée aux rayons X est une technique de la prise d'images non-destructive et son efficacité est largement reconnue. Dans le présent exposé, la tomographie calculée aux rayons X Radio est appliquée avec succès à la visualisation du procédé de perméation de l'eau dans la roche. Une nouvelle technique expérimentale, se servant d'un identificateur principalement constitué d'iodure de potassium (KI), est proposée avec la méthode de l'analyse du champ des vitesse. Le procédé de perméation et le champ des vitesse dans la roche sont visualisés concrètement et analysés en considérant la conservation de masse des identificateurs. Röntgen-Computer-Tomografie (CT) ist eine nicht-destruktive Bildverarbeitungstechnik, deren Effizienz weit anerkannt ist. In der vorliegenden Arbeit wird Röntgen-CT erfolgreich für die visuelle Darstellung des Wasser-Durchdringungsvorgangs im Fels eingesetzt. Eine neue experimentelle Technit mit einem Tracer, der hauptsächlich aus Kaliumiodid (KI) besteht, wird vorgeschlagen, zusammen mit der Analysemethode des Geschwindigkeitsfelds. Der Durchdringungsprozess und das Geschwindigkeitsfeld im Fels werden konkret visualisiert und analysiert, wobei die Bewahrung der Masse des Tracers berücksichtigt wird.

Jan 1, 2003

By D. Bessinger

The present paper provides a brief overview of the thermodynamics of titania rich slags, an outline of the Multi-Phase Equilibrium (MPE) package and its application to ilmenite smelting. Through assessment of published experimental data on various systems containing TiOx, it was found that despite considerable scatter in measured phase equilibria data for the binary Ti2O3-TiO2system,the behaviour of binary and higher order titania rich slags and oxide solid solutions phases could be represented by solution models in the MPE package. Results from the applications of the MPE model on the stability of solid phases and slag-refractory interactions will be presented and discussed. Parallels will be drawn between the predictions by the model and observations made during pilot plant tests. Key words: Thermodynamics, titania slags, ilmenite smelting, phase equilibria, refractory.

Jan 1, 2003