Search Documents

By Launa Mallett, Charles Vaught, Jr. Brnich

This paper introduces a technique for incorporating employee participation into the prevention component of a contingency plan. Companies sometimes focus so much energy on response that they forget to put resources into the basics of emergency prevention. The training program discussed here was designed to make employees part of the prevention system. Examples of training materials from the program are provided, a sample method for introducing risk assessment to employees is shown, and a strategy to address limited training time using short videos is explained. Methods for tailoring the training to any worksite and for specific risks are also included. The program is being designed and tested by the Pittsburgh Research Laboratory/NIOSH and employees of an underground coal mine. Examples are taken from the implementation of the program at the mine during the summer and fall of 1998. Results of the program evaluation and lessons learned during the implementation are discussed.

By R. J. Matetic

Researchers associated with the National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Laboratory (PRL), are investigating injuries (fatal and nonfatal) attributed to water well drillers during well drilling activities. Injury data, obtained from various sources, suggest that many water well drillers are experiencing unnecessarily high insurance premiums and very avoidable citations or violations from the direct result of accidents, injuries, and fatalities occurring throughout the water well drilling industry. Expensive insurance premiums and unnecessary citations are the direct result of poor health and safety practices. Visits to numerous water well drilling sites were conducted by NIOSH personnel to characterize and identify the injury data collected and to provide inexpensive strategies to prevent, minimize, and eliminate safety and health issues associated with water well drilling activities.

Jan 1, 2001

In Maryland, coal mining is confined to Garrett County and the western portion of Allegany .County. Terrain in both counties is predominately level with rolling hills; state law prohibits surface mining in steep slope areas. The Conemaugh and Allegany geologic formations contain five major minable fields or basins. These include: Upper Youghiogheny, Lower Youghiogheny, Castleman, Upper Potomac, and Georges Creek. Maryland's coal reserves are estimated to exceed one billion tons. Approximately 490 million tons of bituminous coal are considered recoverable using conventional mining methods. After World War 11, deep mining declined in Maryland, and by 1977 surface mining accounted for 91 percent of the total production. Since then, production at underground mines has recovered, accounting for 69 percent of the coal production in 1991. Maryland's permanent regulatory program was fully approved February 18, 1982. Its Abandoned Mine Land Program was approved June 16,1982.

Jan 1, 1992

By Thomas E. Marshall, Anthony T. Iannachione, Leonard J. Prosser

The location and time of 2,007 microseismic emissions from a limestone mine in southwestern Pennsylvania were compared with the development of mine faces and the characteristics of the mine layout. Based on analyses of these results, the occurrence of roof failure zones appears to be associated with certain characteristics of the mine plan. It was determined that significant relationships exist between the intensity of the microseismic activity and the scale of the roof failures Microseismic activity associated with these roof falls occurs In distinct episodes, with the final failure event occurring during approximately a 12-hour period. Each roof fall episode appears to be composed of dozens of distinct roof beam failures. As each beam fails in shear and tension, tens to hundreds of audible noises representing rock fracturing or bedding plane separation can occur. While every roof fell can be viewed as unique, certain mechanistic similarities can be realized through careful observation and monitoring of these complex systems. Understanding these similarities in characteristics allows mine personnel to design the most effective and efficient control technique.

By G. Molinda, D. Dolinar

Each year, about 2,000 falls of supported roof occur in the more than 800 underground U.S. coal mines. Therefore to help improve the design of primary support systems, the National Institute for Occupational Safety and Health (NIOSH) conducted a nationwide study of roof falls in over 2,500 km of roadways at 37 coal mines. Information on the roof falls as well as other geotechnical, mining, geologic and roof bolting factors were collected and quantified Then a multi variate statistical analysis was conducted on the data with the roof fall rate being the outcome variable The results were used to derive preliminary design guidelines for predicting the roof bolt length, capacity, and pattern required to effectively reduce the roof fall rate. The equations are fairly limited by a relatively high statistical variance in the data. Also reported is a recent survey of U.S roof bolt manufacturers that shows a significant change in bolt types used over the last ten years.

By Jack Wasserman, Don Wasserman, Gretchen Hinton, Logan Mullinix, Shekar Khanal

Human testing has always been a needed way to provide information on the effects of vehicle vibration, however, the manner of testing has not reflected the real situations of driver’s hands on a steering wheel and a seat with back support and driving tasks. The typical system have used a standard sinusoidal excitation rather than the typical types of road – truck excitations The new truck driver training simulators provide the combination of road roughness, speed effects, cab environment and individual tasks. The system has a full six axis simulation potential. The simulators have the protection of the individual by a combination of two ways for the individual to stop the motion as well as an operator with visual capability who can stop the testing. The closed simulator, shown in Figure 1, has the potential for providing motion during the operation.

Jan 6, 2006

Through 1986, Kentucky was the nation's largest coal producer. Currently it ranks third in production, behind Wyoming and West Virginia. Because of the size and variety of Kentucky's coal industry, virtually every kind of surface coal mining and reclamation activity takes place in the state. Extensive coal deposits occur in two separate areas: the eastern coal field, which is part of the Appalachian coal field, and the western coal field. Kentucky's reserves are estimated at 65 billion tons, with 27 billion tons in eastern Kentucky and 38 billion tons in western Kentucky. Kentucky coal is high in volatile matter, low in sulfur and ash, and relatively high in heating value. Coal from Kentucky's eastern coal fields contains a sulfur content of less than 1 percent. Conditional primacy was granted to Kentucky May 18,1982. Since then, all conditions have been removed; final regulatory approval was granted on May 30,1985. The Abandoned Mine Land Program was approved with the regulatory program May 18, 1982.

Jan 1, 1992

By R. V. Ramani, A. S. C. Owili-eger

The Methane Generator program is a part of the Internal Environ¬mental Sub-system of the Master Design Simulator (MDS). All the sub¬systems of the MDS are controlled and activated by the main program as required. The data requirements for the Methane Generator are supplied by the Geology and Reserves sub-system through common storage. Figure 6 shows the information flow between the Methane Generator and other systems of the MDS. It should be noted that the Methane Generator can also function independently as was described under model application. AREAS OF MISSING INFORMATION In any numerical analysis, the accuracy of the solution depends entirely upon the data available. In gas flow problems, parameters that constitute basic model input data are rock porosity, medium permeability, reservoir pressure and initial reservoir pressure dis¬tribution. Unfortunately, however, most of these characteristics are not available for a lot of coal seams. The need for actual field data cannot, therefore, be adequately emphasized here.

Jan 1, 1974

By Leonard Greenburg

The analytical procedure necessary when using this new impinger•bubbler eil)paratus is almost identical with that em:r;,loyed with the Palm0r a:pp8.ratua. As sugar is not employei, the new apparatus por.;sesses the advantage over the eug.r tube method in having vsry low control errors, being, therefore, much simple in laboratory manipulation during analysis.

Aug 1, 1922

By O. C. Blade, E. L. Garton

Louisiana is one of the major oil-producing States of the country. Commercial production of crude oil in the State began in 1902 and has increased to an estimated output of 157,409,000 barrels in 1945, which is the maximum production up to this time and places the State fourth in the nation. The cumulative production for Louisiana through 1944 is 1,544,481,000 barrels, and, adding the output for 1945, the total to January 1, 1946, is 1,681,890,000 barrels. Data on annual production of crude oil in Louisiana and tentative statistics for 1945 are given in table 1. The large production of crude oil in Louisiana and the present trend to utilize petroleum in accordance with its general characteristics make it increasingly important to present analytical data for crude oils. This report is the fifth of a series presenting such data obtained on crude oils from Louisiana according to the procedure used by the Bureau of Mines. Individual analyses are given for 82 samples from 64 fields; many of the samples are from recently discovered fields, and some are from new producing formations.

Dec 1, 1946

By Jeffrey M. Listak, Gregory J. Chekan

The U. S. Bureau of Mines is investigating longwall panel layouts to maximize coal recovery and minimize interactive problems in multiple-seam operations. When coalbeds are longwall mined in descending order, the transfer of stress from overlying gate roads is a major design constraint affecting pillar stability in the lower mine. The lower mine gate road pillars must be properly designed to withstand the additional load transfer if gate roads are superpositioned in successive seams. The Bureau's MULSIM/NL model, a boundary element computer program, was used to analyze load transfer mechanics for superpositioned gate road pillars. Analysis of Longwall Pillar Stability (ALPS), an empirically based design method for longwall gate road pillars, was used to calibrate model input parameters. ALPS provided a basis to verify model trends and to recommend limits for safe pillar design when superpositioning longwall gate roads. The attributes of the MULSIM/NL model and ALPS were combined to develop a modified method for estimating pillar stress for multiple-seam cases. The modified method uses a multiple-seam factor (MS) to estimate the stress on superpositioned lower mine gate road pillars. Numerical analysis shows that MS depends on the interburden thickness and pillar width.

Jan 1, 1992

By L. W. Scott, T. H. Dubaniewicz, F. T. Duda, P. G. Kovalchik

Recent research conducted by NIOSH, Pittsburgh Research Laboratory showed that electrical current levels permitted under parent regulations may not limit cable temperatures to less than 90 °C in reeled trailing cables. Reeled cables, tightly wrapped with many turns, ell carrying current in an enclosed space, can become overheated due to poor heat transfer. This overheating can cause the cable insulation to soften and become easily damaged. The damaged insulation reduces the life of the cable and can lead to shock, electrocution, and mine foes. This paper describes a method of measuring the conductor temperature of untie trailing cables during no anal operation. The temperature is measured using a 50/175 micrometer Graded Index Multimode Optical Fiber located in the center of the metallic conductors. Distributed temperature measurements arc made using an Optical Time Domain Reflectometer (OTDR). This system is capable of measuring temperature with an accuracy of plus or minus one degree centigrade over a length of 4 km at 1-m intervals. With this unique way of measuring temperature, tests can be conducted simulating actual mine conditions and provide important data to allow MSHA's Approval and Certification Center to develop approval criteria for cyclically rated reeled machines.

By T. E. Marshall, D. R. Dolinar, C. S. Cornpton, L. J. Prosser, A. T. Iannacchione, D. C. Oyler

The U.S., Australian, and United Kingdom coal and the Canadian hard rock mining industries have long recognized the significance of high horizontal stresses as a factor affecting the stability of roof and rib conditions in underground mines. Recently, a growing segment of the U.S. underground stone mining industry has also begun to recognize that horizontal stresses occur in some of its more than 90 mines. Considering the typically high strength and massive nature of limestone, this fact is a revelation in itself. High horizontal stresses produce extensive and sudden rock failures and, in some cases, resulted in injuries to mine workers. Through the years diverse control strategies have been proposed and experimented with. Reorientation of mine entries to reduce stress concentrations have proven successful and are widely accepted in practice. Other solutions, like rock reinforcement, are poorly understood and less accepted in practice. It is the purpose of this National Institute for Occupational Safety and Health (NIOSH) study to develop a better fundamental understanding of these ground control strategies under high horizontal stress conditions through a series of field and laboratory studies. To this end a design technique is presented which provides stone miners with a method for making stability assessments. The consequences of widening rooms, changing geology and horizontal stresses, and different rock bolts on roof beam failures are discussed.

By Sean Gallagher, Christopher A. Hamrick, Arnold C. Love

Twelve subjects participated in an investigation of the biomechanical stresses of asymmetric lifting in stooped and kneeling postures. Three factors were manipulated in this study: Posture (stooped or kneeling), height of lift (35 or 70 cm), and weight of lift (15, 20, or 25 kg). Subjects were required to lift or lower a box every 10 seconds for a period of 2 minutes. Electromyography (PIG) of eight trunk muscles was collected during a lift in this period. The PIG data, normalized to maximum extension and flexion exertions in each posture, were input to a biomechanical model and used to predict compression and shear forces at the L, level of the lumbar spine. Results from the EMG-driven biomechanical model indicated that compression was greater when lifting to a higher shelf (p < 0.001), and indicated a significant interaction between posture and the weight of the lifting box (p < 0.01). Peak lateral shear was not significantly affected by any main effects or interactions (p < 0.05). Anterior shear was increased with increasing height of lift (p < 0.001), and also by the posture x weight interaction (p c 0.01). A multivariate analysis of variance (MANOVA) indicated a complex relationship for recruitment of the eight trunk muscles, with the triple interaction being significant (p < 0.001). The results of this investigation will be used to evaluate safe loads for lifting in these restricted postures.

By James Rowland

On June 1, 2004, the underground coal mine ventilation safety standards under the Code of Federal Regulations (Title 30, Part 75) became effective for the use of a conveyor belt entry as an intake air course to ventilate working sections. These standards, also known as the Belt Air Rule, contained a section which limited the air velocity in the conveyor belt entry to no greater than 500 feet per minute unless otherwise approved by the US Mine Safety and Health Administration in the fire suppression system section of a mine?s ventilation plan. The Belt Air Rule included a requirement dictating compatibility of air velocity with fire suppression systems. The final rule of limiting air velocity in the belt entry was challenged in the Court of Appeals for the District of Columbia Circuit. The court granted that petition and vacated the requirement on the air velocity cap, according to MSHA. The removal of the air velocity cap from the final rule, paired with the compatibility requirement, led to a need for research on high air velocity?s influence on fire suppression system performance in belt entries. Test data was needed that illustrated the relationship between fire suppression system performance and air velocity, especially with the increased use of wider belts in underground coal mines, so National Institute for Occupational Safety and Health and MSHA collaborated to obtain the data. However, this work was initiated before the revised Belt Air Rule was promulgated on December 31, 2008, when 1000 fpm air velocity became a requirement. Four different

Jan 1, 2009

By E. J. HOFFMAN, L. A. SCHOLL, J. c. W. FRAZER

The danger from coal dust in mines has been thoroughly demon- strated by experiment, and consequently the study of the inflam- mability of coal dust suspended in air, that is, the readiness with which a cloud of coal dust inflames, is of decided importance to those engaged in coal mining. Much knowledge has been gained from the work done in the large galleries constructed at official and semiofficial stations in this country and abroad, but the study of the coal-dust problem in these galleries requires so much time and is so costly that there is need of a reliable laboratory method for obtaining a classi- fication of the great variety of dusts that occur in mines. The investigation described in this paper was an attempt to devise such a method. It was a preliminary investigation, and work in the same direction is being continued by the Bureau of Mines. As Mr. Frazer has severed his connection with the bureau, it is deemed advisable to publish the results of his study substantially as he prepared them, with little attempt to draw conclusions or to show the bearing of the results on other studies now in progress. The results of these studies and a full discussion of the significance of the laboratory investiga- tions will be published in future reports of the Bureau of Mines. The reader should remember that any laboratory method, since it involves conditions that differ so greatly from those of actual mining, should be thoroughly tested, and the results obtained by it should be confirmed by experiments conducted on a scale simulating mining conditions before final conclusions are drawn. The need of a laboratory method has long been felt, and several investigators have devised apparatus and methods. The work done by Vital, Holtzwart and Von Meyer, Bedson and Widdas, Le Chate- lier, and that of the British Coal Dust Commission is of great interest in this connection. Bureau of Mines Bulletin 20 contains a sum-

Jan 1, 1913

By Bruce K. Cantrell, Stephen W. Stein, Kenneth L. Williams, David Hassel, Harvey Patashnick

In June 1992, the Mine Safety and Health Administration (MSHA) published the "Report of the Coal Mine Respirable Dust Task Group, Review of the Program to Control Respirable Coal Mine Dust in the United States." As one of its recommendations, the report called for the accelerated development of two mine dust monitors: (1) a fixed-site monitor capable of providing continuous information on dust levels to the miner, mine operator, and to MSHA, if necessary, and (2) a personal sampling device capable of providing both a short-term personal exposure measurement as well as a full-shift measurement. In response to this recommendation, the National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Center, initiated the development of a fixed-site machine-mounted continuous respirable dust monitor. The technology chosen for monitor development is the Rupprecht and Patashnick Co., Inc. tapered element oscillating microbalance. Laboratory and in-mine tests have indicated that, with modification, this sensor can meet the humidity and vibration requirements for underground coal mine use. NIOSH is continuing that effort by developing prototypes of a continuous dust monitor based on this technology. These prototypes are being evaluated in underground coal mines as they become available. This effort, conducted as a joint venture with MSHA, is nearing completion with every promise of success. The immediate benefit of this effort will be to researchers, regulatory personnel, and mine personnel, by permitting evaluation of specific mining practices to see which expose mine workers to excessive dust levels. Using this information, mine personnel can optimize mining procedures to reduce dust exposure. MSHA and the operators will also be able to use the dust concentration data to judge whether dust plan parameters are adequate to continuously maintaining environmental dust levels below the applicable standard. The second development recommended by the Dust Task Group was a person-wearable version of the continuous dust monitor. It will be a monitoring system designed to provide a measurement of worker exposure to respirable dust, both during and at the end of the shift.

By Lisa Steiner

Almost every process has a predecessor, and studying the predecessor helps to define needs and shortcomings to be addressed in the new design. It also suggests what information is needed by the users in order for them to be able to operate safely and effectively. The end users of a system can provide important feedback to better evaluate the current and proposed designs. When new technology is introduced into a system, mishaps may occur before it is realized that human-system interactions were not considered adequately in the design process. A systematic methodology to evaluate the causes of these injuries and to develop remedial recommendations can enhance safety. This paper illustrates how such an approach was used to assess remote machine operation in underground coal mines. The dynamic work environment of underground mining with its unpredictable geologic anomalies can result in numerous hazards. Many of these hazards, including mine roof collapse, occur near the working face where coal is being extracted. The face area is also where the most intricate interactions of people and equipment occur. For these reasons, a high priority has been placed upon minimizing hazards to the workers at the face. A remote control operation was introduced to provide a safer working distance from these hazards. As the remote control technology began to be widely used for extended cut mining operations, new issues became evident. It was essential to develop mechanisms for mines to evaluate these issues in order to predict and reduce injuries. Mining methods and equipment changes must allow for the ability of workers to adapt to changes in their dynamic mining environment. Consideration should be given to how the worker will use familiar information to make decisions in now unfamiliar situations. There will be both intended and unintended consequences [Merton, 1949]. Designers try to anticipate and eliminate surprises, but it is impossible to eliminate them all. How, then, will the new system affect the tasks to workers which are currently accustomed? As suggested below, this question may be addressed and more of the unintended outcomes predicted with a planned design process which includes strong human factors input to determine interactions and behaviors of participants.

Jan 1, 2005

By Christopher Mark, Anthony T. Iannacchione

Falls of ground continue to be one of the most serious causes of injury to U.S. miners. Of the 256 fatal injuries that occurred in mining between 1996 and 1998, 59 (23%) were caused by falls of ground (Table 23.1). Falls of ground affect some sectors of the mining industry more severely than others. For instance, nearly 40% of the 98 coal mine fatalities between 1996 and 1998 were caused by falls of ground. Underground miners are at much greater risk than surface miners. Nearly half (45 out of 101) of underground mine fatalities were attributed to roof, rib, and face falls, while only 6% of the 155 surface fatalities were caused by falls of highwalls or slopes. The goal of this chapter is to provide guidance to safety professionals tasked with preventing ground fall injuries. This chapter combines an analysis of the Mine Safety and Health Administration&apos;s (MS HA) accident and injury data with a survey of industry "best practices" to safeguard miners from ground falls. Ultimately, this approach can help to form the basis of a sound, proactive ground control program for the mining industry. SOURCES OF DATA All the injury data examined in this study were derived from MSHA&apos;s fatal investigation reports and the MSHA accident database. Because falls of ground often result in serious injury, MSHA "Fatalgrams" and fatal investigation reports provide a useful snapshot of ground control issues in the mining industry. These reports are available to the public (on the M FHA Web site at www.msha.gov). Fatalgrams, are one-page summaries that are usually published within a month of an accident. They contain very basic information about the accident with a graphic and a short section on relevant best practices. Fatal investigation reports are the official accident investigation reports filed by MSHA personnel. These reports contain general information about the mine, a, description of the accident, physical factors involved in the accident, a conclusion, and enforcement actions, Enforcement actions typically identify citations and discuss violations to the Federal Mining Law. MSHA also maintains comprehensive statistical data on the mining industry&apos;s accident and injury record. The law requires that mines file a report on every reportable accident that occurs, containing information on the accident&apos;s location, severity, classification, activity, and nature of injury A short narrative is generally included as well. Accident reports can be searched by many of the above fields.

This chapter focuses on smoke as it relates to escape from underground mine fires. Among the topics discussed are the measurement of visibility in smoke; smoke-related hazards such as the production of CO, hydrochloric acid (HCI), or other byproducts of combustion; and miners&apos; personal experiences while escaping through smoke. Smoke Measurement and Visibility In general, smoke consists of hundreds of thousands of very small particles. These particles have some "size," usually expressed in terms of their diameters, and they have some concentrations, usually expressed either in the number of these particles per unit volume or the total mass of the particles per unit volume. Humans cannot see individual smoke particles because they are too small. Similarly, "umber concentrations" and "mass concentrations" of smoke particles do not have much meaning to people unless they are trained technically. Still, individuals know that they can see smoke, independent of all the technical jargon used to describe it. Also, they know that when the smoke level gets too high, it is no longer visible. In fact, nothing is visible because the smoke absorbs all of the light in its surroundings. The eye is only sensitive to light in the wavelength region from about 400 nm to about 700 nm. The maximum sensitivity of the human eye is to light that has a wavelength of about 555 nm. It is important to know how the eye responds to light because if its response is known, it is possible to use a light detector that has almost the same response as the eye. Such a detector can then be used to quantify the visible characteristics of smoke because it responds in the same manner as the human eye. Smoke is visible because it either scatters or attenuates (diminishes) light. In some instances, smoke is visible because the smoke particles reflect light which is then detected by the eye. The eye actually "sees" an intensity of light that has been reflected from a cloud of smoke particles. Imagine shining a flashlight into a cloud of smoke. Someone off to the side can actually "see" the beam of light as it traverses the smoke cloud. This is called scattering. Smoke is also visible be¬cause it attenuates light. Imagine having someone shine a flashlight into your eyes. As smoke begins to build up along the beam of the flashlight, the light begins to dim. The smoke is visible because it is now reducing the intensity of light that falls upon the eye. As the smoke level increases, it is said to obscure our visibility. When the beam is no longer visible, the smoke obscuration is said to be 100%. In other words, none of the light energy from the flashlight makes its way through the cloud of smoke. Another way of saying that the obscuration is 100% is to say that the transmission of light through the cloud is zero.

Jan 1, 2000