Search Documents

Protect rescue workers fighting fires or mine personnel temporarily working in hot environments from heat stress. Approach A specially designed ice-cooled vest is worn while working in hot environments where cooling the mine air is not possible. How It Works The vest holds a total of 44 individual ice cells in packets that are firmly held near the wearer's skin. These ice cells remove heat from the wearer, reducing heat stress and increasing comfort. The locations of the ice cells and packets are shown in the diagram. The vest is constructed in three layers with the outer layer being aluminzed fiberglass cloth. Its aluminized surface reflects radiated heat, and its fiberglass cloth provides fire resistance and strength.

Jan 1, 1979

By T. E. Green

The Bureau of Mines Heavy Metals Program emphasizes the need for improved analytical methods for gold determination. A commercially available ion exchange resin with high selectivity for gold was investigated as a potential method to collect gold from solution. The resin was found to quantitatively collect gold from acid solutions over a wide range of acid concentrations. Common metals were not collected by the resin nor did they seriously interfere with the collection of gold. X-ray spectrographic and neutron activation methods based on the use of papers containing this resin are proposed.

Jan 1, 1970

This pamphlet and the enclosed video describe a safe, effective and economical method for removing dust from work clothes. Background Information Dusty work clothes can increase a worker’s exposure to respirable dust. Respirable dust is usually considered to be particles having an aerodynamic diameter of 10 microns or less and able to enter and deposit in the gas-exchange region of the human lung. A former U.S. Bureau of Mines report documented a 10-fold increase in worker dust exposure on a number of separate occasions from dusty work clothes.* It was found that once clothes become contaminated, they are a continual dust source until cleaned. The only MSHA approved method to clean work clothes requires a HEPA-filter vacuuming system which is very time consuming and difficult to perform effectively. Therefore, most workers use a single air hose (not MSHA approved) which can elevate dust levels for the worker, co-workers, and the work environment. A substantial amount of engineering technology has been developed that, when applied, can significantly lower respirable dust exposures of workers at mineral processing plants. But even with these improvements, some workers continue to exceed their permissible exposure limit. Elevated exposures increase the potential for developing debilitating or fatal lung diseases. ?e clothes cleaning method described within is an example of a continuing effort to reduce the potential for developing these lung diseases. Information about engineering research by the former U.S. Bureau of Mines and NIOSH can be found online at www.cdc.gov/niosh. ?is website can also be used for obtaining NIOSH information about health hazards associated with crystalline silica.

Objective To accurately measure very low air velocities (0-100 ft/min) in U.S. large-opening underground metal/nonmetal mines. Background Hundreds of metal/nonmetal underground mines operate throughout the United States. They extract commercial products from deposits such as limestone, salt, and gypsum. Mining generates a wide variety of gases and dusts, such as silica, diesel exhaust, radon, blasting byproducts, and perhaps even methane. If these substances become airborne, they can adversely affect the health and safety of underground workers. Many metal/nonmetal mines have large cross-sectional airways that could be 60 times larger than an average underground coal mine entry. These large airways require adequate volumes of fresh air to dilute, make harmless, and exhaust the toxic and, at times, explosive byproducts. However, in some underground mine sections, air movement is barely perceptible. The technology of measuring very low air velocities will become increasingly more important for operators of large-opening stone mines in order to monitor miner exposure to diesel particulate matter. Conventional anemometers (e.g., vane) are capable of accurately measuring air velocities only above 100 ft/min. Thus, it was necessary to investigate other anemometry technology to detect low air velocities in the range of 0-100 ft/min. Two different portable ultrasonic anemometers were tested. Actual testing was done in an underground limestone mine with openings about 51 ft wide by 29 ft high. Ultrasonic Anemometers Vane-type anemometers are commonly used by engineering personnel throughout the underground coal mine industry. They work well in measuring air velocities >100 ft/min. However, a separate technology, e.g., portable ultrasonics, is needed to measure air velocities much below 100 ft/min at various places within the large mine opening. Laser-doppler technology was also considered for this application, but was ruled out because of its high cost and other technical limitations. With no moving parts, the portable ultrasonic anemometers are claimed to be accurate down to about 1or 2 ft/min. The first type of ultrasonic anemometer that was examined underground is manufactured by Gill Instruments Ltd., Hampshire, U.K. The U.S. distributor is IN USA, Needham, MA. The Gill Instruments Solent Volometer (figure 1) is a battery-powered, single-axis anemometer meant for measuring low to medium air flows up to1,999 ft/min. It uses the ultrasonic "time of flight" principle where pulses of high-frequency sound are transmitted along the air flow path and the time taken to reach the receiver is measured. The faster the air speed, the quicker the pulses reach the receiver. The second ultrasonic anemometer that was examined under-ground is manufactured by Airflow Developments Ltd., Buckinghamshire, U.K. The U.S. distributor is Airflow Technical Products, Inc., Andover, NJ. The Anemosonic UA-6 (figure 2) is a battery-powered, handheld instrument with digital display. It measures air velocity (0 to 9,999 ft/min) or volume flow, flow turbulence intensity, and air temperature. Neither device is considered to be intrinsically safe for use in underground gassy coal mines. A comparison of salient specifications of both instruments is shown in table 1. The total suspended weight includes the instrument (Gill) or instrument probe (Airflow) plus about 35 ft of connecting cable attached to the pole. This combination of instrument plus cable length allows two operators to measure air velocities up to about 30 ft above the mine floor. Figures 1 and 2 show how each unit would be attached to an extensible, graduated fiberglass rod in order to position the sensor probe at a certain spatial point (centroid of the quadrate) within the underground large opening.

Jan 1, 2003

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

1 14 THIS IS A DIGITAL COMPUTER SIMULATION OF THE VENTILATION SYSTEM OF A MINE LOCATED IN WASHINGTON COUNTY, PENNSYLVANIA. THE VENTILATION SURVEY ON WHICH THIS SIMULATION IS BASED WAS RUN FROM OCT. 27-30 AND ON NOV. 2, 1976 IN THE ACTIVE PORTION OF THE MINE INBY COMBS SHAFT AND THE INACTIVE PORTION AFOUND AND INBY DONAHOO SHAFT. FOLLOW-UP SURVEYS WERE THEN RUN ON FEB. 18 AND FROM MARCH 7-11, 1977 TO INCLUDE THE MAIN HAULAGE SYSTEM OUTBY THE ACTIVE AREAS OF THE MINE. ALL SURVEY DATA WAS NORMALIZED TO A STANDARD DENSITY OF 0.075 POUNDS/CU.FT. PRIOR TO THE CALCULATION OF INPUT PARAMETERS FOR THIS SIMULATION. IN THIS RUN, THE ORIGINAL VENTILATION NETWORK HAS BEEN MODIFIED TO INCLUDE NEW INTAKE AND RETURN AIRSHAFTS AT THE WEST MAINS. IN ADDITION A CONNECTION HAS BEEN MADE BETWEEN THE MINE UNDER STUDY AND A SHAFT IN A WORKED OUT MINE IN THE 1 FACE AREA. THIS SHAFT IS CONSIDERED AN INTAKE SHAFT FOR THIS RUN.

Jan 1, 1977

To reduce air be respirable dust generated from emptying dry dust collectors on small truck-mounted drills used at surface coal mines.

Jan 1, 1995

By E. W. Dean, W. A. Jacobs

"The petroleum division of the Bureau of Mines in its laboratory investigations, has had occasions to develop a number of types of electrical heating equipment. It was found that electric heaters could be used to particular advantage in the standard distillation test for gasoline. (Dean, E.W., Motor Gasoline, Properties, Laboratory Methods of Testing and Practical Specifications, Bureau of Mines Technical raper 214, 1919, 33 pages.) In order to assist in rendering this type of heater available for general use, a description of the apparatus developed by the Bureau was published. (Dean, E.W., A convenient electric heater for use in the analytical distillation of gasoline,. Jour. Ind, and Eng. Chem., Vol.10, 1918, page 823.) Shortly after the article was printed a chemical supply house undertook the manufacture of an electric heater suitable for gasoline distillation. A preliminary model was examined and tested by the Bureau and modifications were suggested that were incorporated in the type of heater that was finally marketed.Description of the Bureau of Mines-heater: The electric heater developed by the Bureau has an inverted conical resistance Plament surrounded by a layer of heat-insulating material and mounted in a metal case having a top of hard asbestos (Transite) board. The resistance element is a helix of nickel-chromium alloy wire held by a molded core of alundum. The Bureau heaters are generally of about 330 watts capacity and are used with stock types of regulating rheostats capable of reducing the effective wattage to about 43 the full-load maximum."

Jun 1, 1920

By D. Harrington, M. W. Von Bernewitz

"The erection of barricades by men who are shut off from escape in mines at time of fire or after an explosion has been consistently advocated by the United States Bureau of Mines. Largely through the publicity given by the bureau to this excellent type of emergency safety endeavor, several hundred lives have been saved during the past 20 years. One of the earliest instances of barricading in the United States of which there is fairly complete record was in connection with the Cherry mine fire in Illinois in 1909; in this fire 259 lives were lost, but 20 men were saved by two barricades and were brought safely to the surface after seven days. In another coal-mine fire, followed later. on by an explosion, at Delagua, Colo., in 1910, 79 lives were lost, but 18 men saved themselves by erecting canvas brattices or barricades; the miners in one barricade were removed safely after five hours and those in another after 21 hours. In 1911, after an explosion in a coal mine at Briceville, Tenn., in which 84 lives were lost, five persons were brought out alive after 58 hours behind a barricade. Twenty hours after an explosion in which 73 were killed at McCurtain, Okla., in 1912, 13 men were taken out alive and one dead from behind a barricade or partition constructed of canvas. In 1914, after an explosion at Eccles, W. Va., in which 181 were killed, 35 men barricaded themselves in one place and after four hours were brought to the surface alive; this barricade was also of canvas. In 1915, 112 men were killed in an explosion at Layland, W. Va., but two groups of men, 47 in all, were able to barricade themselves; after four days 46 men were rescued alive, but one man was dead. In 1915, an explosion at Boomer, W. Va., killed 23, but 27 others barricaded themselves in one place and after seven hours came out alive. All of the foregoing instances of barricading were in coal mines. In 1917 there were three cases of barricading in a Montana metal-mine fire (the North Butte) during which 163 lives were lost. One of the barricades, sheltering 19 men, failed because the region barricaded was in porous broken ground through which the poisonous gases seeped and killed the entire group. From another of the barricades, engineered by an assistant foreman, 8 men were taken out, 6 uncon¬scious and 2 dead, 50 hours after the fire started. The 6 unconscious men lived, out the assistant foreman who directed the men was one of the 2 who had died. In the third case of barricading in this metal-mine fire,,men, also led by an assistant foreman, kept themselves closed in for about b6 hours and then broke barricade or bulkhead, 25 oing in one direction to safety, and 4, including the assistant foreman, going in another direction to death from poisonous gases. There have been a number of other cases of barricading, some successful and others a failure. Probably the worst failure was that in the argonaut (gold) mine fire in California in 1922; all of a group of 46 miners behind a barricade were found dead when reached after 21 days."

Apr 1, 1933

By Frank E. Chase, John Rusnak, David Newman

During the past quarter century, coal mine geologists have evolved from providing a qualitative description of drill core and coal reserves into quantitative geotechnical specialists who bridge the gap between geology and engineering. In the late 1970’s and early 1980’s, hazard prediction mapping was in its infancy. At best, hazard maps identified rudimentary structures and conditions such as stream valley locations, sandstone/shale transition zones, and lineaments. A “technical disconnect” had existed between geologists and mining engineers as each profession operated largely independent of each other. Engineers did not readily integrate geology and geologic conditions, with the exception of coal thickness, into mine planning. Geologists were relied upon for reserve estimates and did not participate in mine planning or design. The employment and market slump of the 1980’s and 1990’s combined with mining more challenging reserves mandated that this gap be bridged and forced geologists to learn to speak more “numerically” to engineers so they could be understood. The purpose of this paper is to describe the procedures and thought processes used by coal mine geologists when determining various mineability and reserve extraction feasibility issues. The paper will also address underground geologic hazard mapping and prediction techniques. To achieve these objectives, the opinions and experiences of leading coal mine geologists, geotechnical and strata control specialists across the United States were solicited.

Increase the safety of operators of front-end loaders by providing a means of monitoring the machine's stability. Approach Through a research contract, the Bureau of Mines developed a front-end loader stability indicator which provides the machine operator with a reliable, easily interpreted display assessing the stability of the machine. How It Works Statistics show that front-end loader accidents are the largest single category of machinery-related accidents in the surface mining industry. Many of the fatalities resulting from these accidents occur when front-end loaders rollover and either crush the operator who is trapped within the cab or strike the operator who is trying to jump to safety. Although rollover protective structures (ROPS) are required by law on front-end loaders to protect operators in the case of a rollover, these do not prevent the actual rollover from occurring. In fact, the operator has no way of evaluating the stability of the machine except by using personal judgment. The Bureau of Mines responded to this problem by developing a front-end loader stability indicator whose primary function is to Indicate to the operator when the machine is approaching an unstable situation which may trigger a rollover. The device bases Its interpretation on measurement of the normal loads on the machine's wheels. Strain gage instrumentation located on the machine is used to monitor the magnitude and change of forces acting normal to the front-end loader's wheels. These forces are direct indicators of the machine's center of gravity relative to its position on the ground. The strain gages are connected to electronic circuitry which amplifies and processes the signals. Stability or instability of the loader is relayed to the operator through a display of green, amber and red lights.

Jan 1, 1986

By Robert C. Hickman

"INTRODUCTION The Cline mine has been worked intermittently for copper and gold since 1895. Scheelite has recently been detected with the aid of a ""Mineralite"" on the old waste dumps of the mine. Four diamond-drill holes were drilled by the Bureau of Mines from August 13 to September 25, 1946. Results of this drilling showed the vein to pinch at depth and to carry no mineralization of economic importance.ACKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, does the actual investigation work, and prepares the final report. The Metallurgical Branch, Oliver C. Ralston, chief, analyzes samples and makes beneficiation tests.The project was under the general supervision of Mitchell H. Kline, chief, Raleigh Division, Mining Branch.Acknowledgment is due Dr. Jasper L. Stuckey, State geologist, for logging the drill core and to J. B. Zadra and associates, Metallurgical Branch, College Park, Md., for analytical determinations."

Feb 1, 1948

By Erica E. Hall, Robert H. Peters, Charles Vaught, Jon C. Volkwein

Coal Workers Pneumoconiosis is the leading cause of death due to occupational illness among coal miners. This disease is caused by miners’ exposure to respirable coal mine dust. A Personal Dust Monitor has recently been developed to provide near real time feedback to miners regarding the number of milligrams of respirable coal mine dust in the air they breathe. This paper was prepared by the National Institute for Occupational Safety and Health to document coal miners’ reactions to this new device, and how they make use of the information it provides. Structured interviews were conducted with 30 coal miners at four mines. A four-stage conceptual model of miners’ decision processes with respect to how they interpret and respond to the dust exposure numbers from their personal dust monitor is proposed. The stages are: Diagnosis, Action Planning and Intervention, Evaluation, and Institutionalization. The interview responses provide considerable support for the model. Most miners paid attention to Personal Dust Monitor feedback and made efforts to reduce their dust exposure. Their efforts included: changing where they positioned themselves, making ventilation system improvements, and using respirators more often. The 29 miners who reported having experience wearing both the old and new type of dust monitors were asked which dust sampling system they preferred. Eighteen (62%) preferred the new monitors, 7 (24%) preferred existing monitors, and 4 (14%) had no preference. The most frequently cited advantage of the new monitor is its ability to provide relatively quick feedback on dust exposure. Miners provided several suggestions for improving the design of the instrument.

By Doug Tesarik

The study of neutrinos?particles infinitesimally smaller than atoms?would be significantly advanced if a deep underground facility were available that would filter out unwanted cosmic radiation. Encouraging progress has been made in satisfying the criteria for such a facility with the selection of the Homestake Mine in Lead, SD, by the National Underground Laboratory Committee as the recommended site for a National Underground Science Laboratory (NUSL). The Homestake Mine is America?s oldest and deepest underground mine, and its well-maintained infrastructure to depths of 2438 m below the surface makes the mine an excellent site for such a laboratory. The investigation reported here is an initial study of the stability of the first of the proposed chambers. A cylindrical room with a dome-shaped roof and floor was analyzed in three dimensions using the finite-difference program FLAC3D. The results were compared to recommended support requirements based on Barton?s Tunneling Quality Index, Q. Based on model results and observations from previous mining studies, large rooms with 50-m roof spans can be constructed and will remain stable at 2141 m below the surface in the Poorman Formation when the rock is reinforced with cable bolts. Construction may be possible at lower levels in the Yates Formation if more extensive laboratory strength tests confirm initial results.

Jan 1, 2002

"The main objective of this research is to identify the mechanisms of control of respirable dust generation in coal mines. Full understanding of the mechanics of crack propagation in coal is of fundamental importance in studies of the generation and control of respirable dust.The main objectives of this fracture investigation are: 1) to determine reliable data on the fracture toughness of coal as a parameter controlling unstable crack propagation; 2) to determine fracture propagation velocity in coal providing data on the terminal velocity at which crack bifurcation occurs and fine fragments of coal material are generated; and 3) to apply the critical strain energy density criterion to model mixed mode crack propagation in coal.The development of the protocol, laboratory procedure and equipment necessary to conduct an extensive mixed mode fracture toughness testing program has been completed. About 80 mixed mode fracture toughness tests, 10 good fracture velocity records and over 50 fracture surface examination with the SME are available. The details of the mixed mode fracture toughness testing are available in a paper titled, ""Development of Mixed Mode Testing System for Geologic Materials"" which is available from the center. The average fracture toughness and critical strain energy density values for the three seams investigated to date are included in the attached Figures 71, 72, 73."

Nov 1, 1988

By Jeffrey Shawn Peterson

Among underground coal miners, hearing loss remains one of the most common occupational illnesses. In response, the National Institute for Occupational Safety and Health (NIOSH) conducts research to reduce the noise emission of various underground coal mining equipment, an example of which is a roof bolting machine (RBM). After the removal of coal or rock, the remaining strata may be subject to fall, either from overhead (the roof) or from the side (the rib). One method used in underground coal-mines to prevent failures requires the installation of roof bolts. The roof bolting machine operator trams the machine to the required location, drills a hole into the strata, and then installs a roof bolt, supporting the roof or the rib, as the case may be. Field studies support the premise that, on average, drilling noise is the loudest noise that a roof bolting machine operator would be exposed to and contributes significantly to the operators? noise exposure. NIOSH has determined that the drill steel radiates a significant amount of noise during drilling. NIOSH is developing bit and chuck isolators to reduce vibration, and thus noise radiation of the drill steel, with the longer-term goal of reducing roof bolting machine operator noise exposure. Laboratory testing has shown that operator ear sound pressure levels may be reduced by 3 to 7 dB(A), depending upon the test configuration and drilling media.

Jan 1, 2009

By Robert L. Chufo

This paper describes a general purpose imaging technology developed by the U.S. Bureau of Mines (USBM) that, when fully implemented, will solve the general problem of "seeing into the earth." A first generation radar coal thickness sensor, the RCTS-1, has been developed and field-tested in both underground and highwall mines. The noncontacting electromagnetic technique uses spatial modulation created by moving a simple sensor antenna in a direction along each axes to be measured while the complex reflection coefficient is measured at multiple frequencies over a two-to-one bandwidth. The antenna motion imparts spatial modulation to the data that enables signal processing to solve the problems of media, target and antenna dispersion. Knowledge of the dielectric constant of the media is not necessary because the electrical properties of the media are determined automatically along with the distance to the target and thickness of each layer of the target. The sensor was developed as a navigation guidance sensor to accurately detect the coal/noncoal interface required for the USBM computer-assisted mining machine program. Other mining applications include the location of rock fractures, water-filled voids, and abandoned gas wells. These hazards can be detected in advance of the mining operation. This initiating technology is being expanded into a full threedimensional (3-D) imaging system that will have applications in both the underground and surface environment.

By Earl C. Lane

The Bureau of Mines is making a survey of petroleum products manufactured on the Pacific Coast from California crude oils . California crude petroleum is known to differ in some characteristics from the crude oil produced in other parts of the United States , and the claim has been made that the present Federal specifications are unduly severe when applied to the products made from California crudes . The main purpose of the present survey is to determine whether these claims are justified . This report deals only with California gasolines . Other products , such as burning oil , fuel and lubricating oils , will be taken up later . The samples reported were furnished in most cases , by the four large refining companies located on the Pacific Coast , although a number of samples of motor gasoline were purchased in the open market . In Los Angeles , samples of motor gasoline were obtained from service stations representing as many different refineries as possible . Inasmuch as San Francisco is one of the cities covered by the regular semi -annual motor gasoline survey conducted by the Bureau of Mines , it was not considered essential that the set of samples obtained from this city be as comprehensive as would otherwise have been necessary . The gasoline consumed in the States of Washington and Oregon is furnished for the most part by California refineries , and no effort was made to procure samples from these States .

Apr 1, 1922

By R. J. Matetic, D. Elsworth

The objective of this U.S. Bureau of Mines hydrologic-subsidence investigation was to evaluate the effects of longwall mining on the local ground water regime through field monitoring and numerical modeling. Field data were obtained from multiple-position borehole extensometers (MPBX's) that were used to measure subsurface displacements. Survey monuments were installed to measure mining-induced surface deformations. Numerous drawdown and recovery tests were performed to characterize hydrologic properties of the overburden strata. Coreholes were drilled above the study area to determine lithologic and strength characteristics of the overburden strata using the rock samples collected. Electronic recorders were installed on all monitoring wells to continuously monitor ground water levels in coordination with mining of the longwall panels. A combined finite element model of the deformation of overlying strata, and it's influence on ground water flow was used to define the change in local and regional water budgets. The predicted effects of the postmining ground water system determined by the model correlated well with field data collected from the field site. Without an infiltration rate added to the model, a static decrease of 3.0 m (10 ft) in water level would occur due to mining of both longwall panels and if an infiltration rate was inputted in the model, no predicted long-term effects would occur to the ground water system.

Jan 1, 1995

By Noel N. Moebs

The Bureau of Mines measured surface subsidence above four small coal mine room-and-pillar sections in southwestern Pennsylvania, to obtain preliminary information on the magnitude and character of selected parameters, such as angle of draw and maximum subsidence, which are essential to the development of subsidence prediction methods. Data varied widely at the four sites; this is attributed to local geologic and mining conditions. Surface deformation at each site was of a magnitude normally associated with severe structural damage.

Jan 1, 1982

By Brian White, Hamid Maleki

Sudden, violent failures of rock around mine openings influence access, ventilation, and safety in both hard-rock and coal mines. To develop predictive tools for assessing the potential for violent failure, the authors initiated a comprehensive study using (1) multiple linear regression and numerical modeling analyses of geological and mining conditions at 25 sites to identify the most significant factors contributing to stress bumps in coal mines and (2) investigations of the geological and mining factors contributing to rock bursts in the Coeur d'Alene Mining District of northern Idaho, particularly the influence of preexisting structures on rock bursts. Twenty-five factors were initially considered in the study of coal bumps. The most important variables were identified as (1) mechanical properties of strata, (2) gate road geometry and/or gate pillar factors of safety, (3) roof beam thickness, joint spacing, and stiffness characteristics, and (4) stress gradients associated with previous mining and anomalous geologic conditions. In the Coeur d'Alene district, burst damage related to preexisting structures results primarily from (1) sudden buckling and crushing of rock layers where surfaces of development and production openings lie at low angles to bedding, faults, or other planar structures and (2) disturbance of loose ground caused by seismic fault-slip on preexisting faults or previously sheared bedding planes that intersect veins near pillar-stope margins.