Search Documents

By L. C. IlsLey

It is most unfortunate that a few must often suffer , and perhaps die , that many may benefit from a fuller appreciation of the dangers surrounding mining operations , and the proper use of safeguards designed to offset these dangers . This has been the case during the last few months in the anthracite field , where several explosions , resulting in burnings and fatalities , were undoubtedly caused by the use of defective or improperly assembled flame safety lamps . Had this same lack of understanding regarding the proper assembly of this safety device , and had the same indifference on the part of the user in keeping the lamps locked at all times and in proper condition , been permitted in a region where the coal dust was explosive , a terrible disaster would surely have resulted . In nearly every coal -mining country , including the United States , the Davy and Clanny type of lamp has been superseded , and rightly so , by some kind of bonneted lamp . Bonneted lamps , especially of the naphtha type , while much safer than the unbonneted , have more parts and need more care in assembling . For this reason the burden of responsibility for their being properly assembled rests with the lamp man ; therefore , it is extremely important that only competent , conscientious men be given this work .

Dec 1, 1921

By H. Kenneth Sacks

The Bureau of Mines has developed hardware for electromagnetic (EM) detection and location of miners trapped in underground coal mines. This report describes a technique for using the developed equipment for locating uncased boreholes underground. Results of several field and laboratory experiments are described.

Jan 1, 1978

By L. C. IlsLey

The Burrell methane indicator developed by Col. G. A. Burrell in 1915 was modified during 1918 to the " insulated type " Burrell indicator . Though this instrument has been used in mines since its first introduction , it was not formally approved as safe and efficient for use in gaseous mines until March , 1922. The indicator is built by the Mine Safety Appliances Co. , Pittsburgh , Pa . Approval No. 800 has been assigned to this company covering the device in the form approved . The principle of the Burrell indicator is fairly well known . It works on the same principle as the Haldane apparatus - measuring by means of a graduated scale , the contraction resulting from burning the methane content of an air and gas sample . A given aniount of the mine atmosphere to be tested for methane is taken into the indicator . This sample is then thoroughly shaken with the water in the indicator for one minute . The methane in the sample is now burned for two minutes by a heated platinum coil , which is energized by a small storage battery containing two Edison cells connected in series . After the glower or coil has burned for two minutes , it is disconnected from the battery , and the indicator is again shaken for The amount of contraction observed by reading the height the water rises in the U- tube of the indicator , which is calibrated to register the percentage of gas in the sample . The indicator as approved by the Bureau of Mines is equipped with an Edison M- 8 mine- lamp battery , and with a glass and scale graduated from zerɔ tɔ four per cent methane . The approval of a corbination service that is , an attachment for giving illumination from the same battery from which the platinum glower is operated has been withheld pending the development of a battery with larger capacity . - Under laboratory operating conditions , a single glower was capable of making at least 20 determinations if proper precautions were observed with respect to the use of freshly charged batteries . A battery should be allowed to stand off charge several hours before using in an indicator , as the peak voltage of a freshly charged Edison cell is abnormally high and is likely to send enough current through the glower to melt the platinum wire . Fifty-seven satisfactory operations were obtained from a completely charged battery . The point where the voltage of the cell fell below 2.3 volts with the glower attached was taken as the lower limit of successful operation . A voltage less than 2.3 does not permit the lower to burn at a temperature that will completely burn the gas in the air , thus giving a false indication .

Jun 1, 1922

By Jan M. Mutmansky, Christopher J. Rise

"One of the most serious long term health problems associated with underground,mining is Coal Workers Pneumoconiosis (CWI'), more commonly known as Black Lung Disease. It occurs in some coal workers, normally after 15 or more years of exposure to coal mine dust, and leads to a variety of respiratory problems. Two types of pneumoconiosis are recognized simple CWP, which has been estimated to affect 6.9 percent of miners and is a condition that does not impair the miner's ability to work nor reduce life expectancy; and a more severe form of black lung (called progressive massive fibrosis) that occurs in about one percent of the cases and results in severe lung damage.Although the relationship between coal dust and CWP has long been recognized, detailed knowledge of the relationship is insufficient for setting up authoritative guidelines to reduce the health risks for those employed in dusty,underground environments. CWP is not only a health problem for workers that causes considerable distress, it is also a very expensive problem the total annual costs associated with CWP approach two billion dollars.As part of its efforts to combat CWP, the U.S. Bureau of Mines in 1983 established a Generic Mineral Technology Center to carry out basic research into all aspects of respirable coal dust:— control of dust generation — the behavior of dust in the mine — characterization of dust particles interaction of dust and lung— the relationships among dust generation and mobility and the mine environment, geology, and seam characteristics,Penn State, West Virginia University, the University of Minnesota, and the Massachusetts Institute of Technology are involved in this research, which is administered from the Department of Mineral Engineering at Penn State.Our work is one of the seven projects to be conducted at Penn Slate. We are concerned particularly with the characterization of dust and its relationships with the mine environment, and our main goal is to establish standard procedures for describing and measuring these variables.Coal DustCoal dust is a very complex material that varies greatly in chemical and mineralogical properties. Moreover, it is not the only constituent of respirable dust in the mine. When a coal seam is mined, it is inevitable that rock particles other than coal are included in the material. This rock comes from the mine roof, the floor, and the partings and inclusions within the coal scams. Since the roof and floor strata, the partings and inclusions are often stronger than the coal, mining them frequently causes more dust than mining the coal itself. One of the objectives of our research is to find the relationships between a specific coal's characteristics before it is mined and the respirable dust characteristics after it is mined. We are particularly interested in the size distribution of particles, the chemical properties, and the mineralogical properties."

Jun 1, 1988

By C. F. Swab

A relatively innocuous halocarbon was investigated as a substitute for the highly toxic carbon tetrachloride in the approval testing of chemical cartridges. The vapor effluent of 1,1,2-trichloro-1,2,2-trifluoroethane from chemical cartridges is continuously monitored by a nondispersive infrared analyzer. Breakthrough times for the cartridges, using the halocarbon, can be equated to those of carbon tetrachloride, if multiplied by the factor, 1.49.

Jan 1, 1970

By C. P. Lazzara, R. A. Franks, G. F. Friel, J. C. Edwards, J. J. Opferman

It was determined that a selection of different types of fire sensors could be used to discriminate mine fires from nuisance emissions produced by diesel equipment. A neural network (NN) was developed for application to coal, wood, and conveyor belt fires in the presence of diesel emissions and evaluated with the successful prediction of twenty-two out of twenty-three mine fires based upon a fire probability determination. The optimum sensor selection for the NN was comprised of a carbon monoxide (CO) sensor, two different types of metal oxide semiconductor (MOS) sensors, and an optical path smoke sensor.

By BUREAU OF MINES

A complete list of permissible mining equipment, rescue apparatus and gas masks tested prior to July 1, 1928, was published in Bureau of Mines Information Circular 60772. The present list includes practically all equipment tested and, approved by the Bureau, up to and including Jan. 1, 1929. It covers electric air compressors, coal drills, mining machines, loading machines, conveyors, mine pumps, room hoists, mine telephones, rock-dusting machines, switches, electric cap lamps, flame safety lamps, electric hand and trip lamps, flash lamps, methane indicators and detectors, blasting units, storage barrery locomotives, tandem locomotives, power trucks, concrete mixers, self-contained oxygen breathing apparatus and gas masks. The system under which those devices were tested permits the manufacturer, after his equipment has passed certain tests prescribed by the Bureau of Mines, to mark his equipment with a seal shoring that it has been "approved" by the Bureau. These tests are designed to insure that the equipment has the minimum requirements for safety in use. The only object of the Bureau in making such tests and pub- lishing lists of permissible equirment is to safeguard the lives of workers and to help lesson the hazards of mining.

Jan 1, 1929

By Charles L. Kimbell

This study is intended to serve three roles. First, it represents a global overview and summary to supplement and complement the five regional companion volumes of the 1991 edition of the Minerals Yearbook International Review. In this regard, it also extends previous time series under this title that appeared as the introductory chapter to the international volume of the Minerals Yearbook from the inception of that volume in 1963 until it was subdivided into separate regional volumes in 1989. The basic statistical presentations herein generally contain data through and including that for 1991, although in a few instances the most recent statistics are those for earlier years because more recent, comprehensive global statistics simply are not yet available owing to delays in data collection and processing in some countries and continued governmental suppression of data in others. The second role of this study is to provide an update to the coverage of events impacting the world's mineral industry that have occurred between the end of 1991 and the preparation of this study. Inclusion of this update is almost essential because of the potential effect of some of these events on global mineral industry activities.

Jan 1, 1993

By Richard L. Unger

Equipment is the primary cause of injury in 11% of all mining accidents and a secondary cause in another 10%. Purchasers should select new equipment carefully to ensure that the machine incorporates good ergonomic design criteria that maximize the safety of their mine workers. One potential problem area is the workstation-the control center of the machine. Safety problems often occur when the workstation provides insufficient clearance or visibility to the operator or has controls that are difficult to reach. This is especially true for underground mines, where confined space is an issue. In reclined or stooped postures, operators will have less strength and agility and often experience reduced visibility. We have conducted and published much research in Human Factors design of mining machine workstations. This information is currently being compiled into a series of Human Factors design recommendation reports. The reposts dl cover many topics, including workstation layout, control design, seating, and visibility. Each topic has a list of basic or first principles of design. Understanding these principles is the key to designing or purchasing a workstation that is both safe and efficient. Following is a sampling of these main topics and first principles.

Aug 1, 1996

The National Institute for Occupational Safety and Health (NIOSH) recommends that occupational exposures to respirable coal mine dust and respirable crystalline silica* be controlled by complying with the provisions presented in this document. These recommendations are designed to protect the health and provide for the safety of workers exposed to respirable coal mine dust and respirable crystalline silica for up to 10 hr/day during a 40-hr workweek over a working lifetime. The information presented in this document demonstrates that underground and surface coal miners are at risk of developing simple coal workers' pneumoconiosis (CWP), progressive massive fibrosis (PMF), silicosis, and chronic obstructive pulmonary disease (COPD). Adherence to the recommendations in this document should prevent or greatly reduce the risk of adverse health effects in workers exposed to respirable coal mine dust and respirable crystalline silica. NIOSH recommends that preventive efforts be focused primarily on reducing worker exposures. Effective health and hazard surveillance and medical screening are also useful components of a comprehensive prevention effort.

Jan 1, 1997

By J. Brad Seymour, Mark K. Larson, Richard L. Rains, Douglas R. Tesarik

For several years, researchers from the Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) have been using geotechnical instruments in underground mines to study ground control problems and develop means of reducing accidents and fatalities caused by ground falls. This paper describes many of the different types of instruments, sensors, and data acquisition equipment that have been used for these studies; briefly explains the advantages and disadvantages of various sensor technologies; provides practical recommendations regarding the use of specific instruments and data acquisition systems; and outlines a general approach to the design and implementation of a successful instrumentation plan. A wide variety of instruments are commercially available for measuring deformation, strain, stress, and/or load. If used correctly, these instruments can provide important quantitative information regarding the mining-induced behavior of the host rock, the performance of ground support systems, and the safety and stability of underground workings. Data collected from these instruments can warn mine staff of impending ground control failures or hazardous working conditions, as well as provide valuable information for the design of ground support systems and the configuration and sequencing of mining excavations. We hope that the practical information presented in this paper will encourage a more widespread use of geotechnical instruments in underground mines and lead to reliable measurements that aid the engineering decisions affecting the safety of miners.

Jan 10, 2000

By Garrett R. Hyde

Sintered yttria and sintered dysprosia can be used to make single-component thermistors having typical thermistor geometries and operable in the temperature range 500° to 1,200° C. However, at these temperatures, instability of platinum electrodes can contribute a slight aging effect if the thermistor is kept near 1,200° C for long periods. Typical characteristics at 500° C for an yttria disk thermistor 12 mm in diameter and 2 mm thick are a resistance of 12.4 megohms and a temperature coefficient of resistance of -3.8 percent per degree C. Typical characteristics at 500° C for a dysprosia thermistor of the same dimensions are a resistance of 1.84 kohms and a temperature coefficient of resistance of -1.6 percent per degree C.

Jan 1, 1970

By J. A. Eisele

The Bureau of Hines conducted a bench-scale investigation of a concentrated H2S04 reaction for recovering and separating rare-earth elements, barium, and strontium from a bastnasite ore and byproduct. Barium and strontium were dissolved in the concentrated acid and precipitated as a mixed product by water dilution. Separation of strontium from barium was effected by reaction with Na2C03 solution, followed by a dilute acid leach of the SrC03 formed. After removing the barium and strontium from bastnäsite are, the rare-earth elements were roasted to water-soluble sulfates. The rare-earth sulfate solution was subsequently processed by solvent extraction to produce rare-earth oxides low in lead and magnesium.

Jan 1, 1974

By M. J. Sapko

The Bureau of Mines conducted laboratory-scale flammability experiments to investigate the possible use of water spray systems for inerting or quenching mine-gas ignitions, such as those encountered at the working face of a coal mine. The inerting results for premixed methane-air-water mixtures indicated that water droplets of less than 10 µm tend to be as effective as the vapor. Water requirements for inerting such mixtures were much smaller than those for quenching the sustained flame propagation by the application of water sprays. The minimum water mass concentration for quenching methane-air flames increased linearly with increasing droplet diameter (surface weighted mean) and decreased with increasing spray temperature, whereas the droplet surface area required per unit volume was essentially constant for a given gas mixture composition. Data extrapolations indicated that a quenching system may be feasible for the longwall mining application.

Jan 1, 1977

By A. Mayton, A. Brien, W. Porter, O&apos

In 2004, management at Unimin's Gleason, TN operation began implementing ergonomic interventions specifically targeted to reduce risk of musculoskeletal injuries (MSIs). Together with corporate and site management, Unimin identified work site hazards and began to modify work practices/equipment. Some interventions were relatively simple and were implemented immediately. Others, like improvements to a mobile shredder, were more complex but were eventually resolved through a participatory approach with employees, management, manufacturers and NIOSH. This paper discusses ergonomic interventions that were successfully implemented using a bottom-up approach to reducing the risk of injury.

Improve the accuracy of commonly-used mine air velocity measurement techniques. Approach The Bureau of Mines, through a contract with Ketron, Inc., conducted a detailed study to establish appropriate, generalized correction factors for commonly-used air velocity measurement techniques. The techniques used were centerline readings, continuous traverse and split traverse vane anemometer readings, and smoke cloud readings (see Bureau of Mines Bulletion 589 for details on the proper use of these techniques). The various measurement techniques were used at different mine test sites to measure different air velocities. The data collected from the test sites were used in a statistical analysis which determined a generalized correction factor for each measurement technique. The correction factor multiplied by the measured velocity was used to provide the true velocity.

Jan 1, 1984

By Charlie Wyche

Principal mineral products in the Dominion of Fiji were gold, silver, pit and quarry construction materials, and cement. In the years 1978-79, the combined total value of these commodities accounted for some $15 million,2 or 85% of the total mineral output. Production of cement, sand and gravel, and quarry products increased substantially, but gold and silver output from Fiji's only operating metal mine continued the down-ward trend of recent years. Mineral exploration by several international mining companies as well as by local prospectors was being carried out over much of Fiji, and a number of interesting prospects were discovered. One of these, a medium-size porphyry-copper prospect in the Namosi area of Viti Levu, W88 at a mining feasibility study stage. At Mount Kasi on Vanua Levu, an extensive program of geological sampling and mapping W88 being conducted, and surface sampling and drilling W88 taking place at some base metal prospects in the south-central parts of Viti Levu. Also, high gold values in surface samples were reported at Vuda in western Viti Levu.

Jan 1, 1981

Provide a full-scale test facility where the effectiveness of all types of subsidence abatement techniques can be evaluated under controlled conditions. Background Subsidence is ground movement resulting from the collapse of overlying strata into a mine void because of failure of the mine roof, mine floor, or support pillars. The failure may propagate to the surface and be expressed as a depression, cracks, or a sinkhole. The surface expression of such features may be delayed until long after mining has been completed. Subsidence has the potential to affect more land area than any other type of abandoned mine land problem. Subsidence also causes direct damage to real property, with significant financial loss and more importantly, presents a danger to public health, safety, and general welfare. Subsidence-related problems are considered to be one of the most important abandoned mine land issues. Backfilling of mine voids is the most common stabilization method used to abate subsidence and protect surface structures. Backfilling or placement of material is performed by hydraulic flushing or pneumatic stowing, using either in-mine or remote methods. The majority of the past subsidence abatement projects has been performed using remote methods from single or multiple boreholes. Other subsidence abatement techniques arc available. For example, various point support methods are used to protect small areas of the land surface and surface structures, without completely filling the mine void. These may be more appropriate under different conditions. Little documented information is available concerning the capability of the various backfilling methods for completely filling a mine void or providing long-term structural strength. Therefore, the Bureau of Mines developed a laboratory for controlled evaluation of backfilling technologies.

Jan 1, 1991

By Fred Baldassare, Marcia Harris, Kenneth K. Eltschlager

Surface mine blasting was recently investigated as a potential source of high concentrations of stray gases found in nearby residences of western Pennsylvania. In one incident carbon monoxide was detected in a home and in the other, high concentrations of carbon dioxide were found in a home. Both carbon monoxide and carbon dioxide are by-products of blasting. However, other potential sources of these gases may also exist in a residential setting. In each case, gas chromatography (GC) and carbon isotopic analyses were used to define atmospheric concentrations inside the homes, and to determine the source of a stray gas. Molecular and isotopic analyses provide geochemical evidence as to the origin and source of the stray gas. This paper discusses elements of a stray gas investigation and the analyses necessary to identify the source of a stray gas.

By R. Hogg

"Some basic features of the science and technology of particle systems are reviewed in the context of agglomeration processes. Emphasis is placed on the force of interaction among particles and with their environment and on their dependence on particle characteristics and interfacial phenomena. The complex role these forces play in the various stages of agglomerate formation, growth, consolidation and structure development, and their influence on final product properties is discussed.INTRODUCTION Agglomeration is an example of a process where the technology has generally preceded the science. Process development• has very often been by trial-and-error albeit with an eye on some basic principles. Nevertheless there is' a scientific basis to the process and a better understanding of the fundamentals can surely lead to improvements in process design and control.Successful processes for the agglomeration of fine particles depend on proper control of the adhesional forces between particles, to encourage agglomerate formation and growth and to provide adequate mechanical strength in the product. At the same time the rheology of the particulate system can be critical to the rearrangement of particles necessary to permit densification of the agglomerate and the development of an agglomerate structure appropriate to the end-use requirements.AGGLOMERATION SYSTEMSUltimately, the performance, of any agglomeration process depends on the• characteristics of the particles and their environment. The specific effects, however, are often complex and may be very difficult to pinpoint by simple observation of the process. A typical agglomeration process involves a number of concurrent or consecutive steps - adhesion, growth, compaction, etc., - each of which is affected by the characteristics of the system, but not necessarily in the same way. The effect of particle size, say on agglomerate growth may be quite different from its effect on compaction and its optimum value may differ widely from one stage to the other. Obviously there.is a general need for compromise in the design and operation, of agglomeration systems. Furtnermore, an understanding of the details of the process and their complexities can be critical to process optimization and improved product quality control."

Jan 1, 1989