Search Documents

Assist in controlling or extinguishing fires that occur in abandoned mine lands (AML) by providing a compilation of information on past fire control projects, the estimated extent of the current problem, and factors affecting the occurrence, propagation, and extinguishment of AML tires. Conventional fire control methods and their probable effectiveness are evaluated. Background Fires that occur in abandoned coal mines, waste banks, and coal outcrops constitute a serious health, safety, and environmental hazard from toxic fumes, deterioration of air quality, and subsidence. Although fires on AML occur in every coal-producing State, the severity of the problem varies, with most underground fires occurring in Kentucky, Pennsylvania, and Wyoming. Surface fires are prevalent in Kentucky, Pennsylvania, and West Virginia. Methods to extinguish or control AML fires, including excavation, fire barriers, and scaling, are generally expensive and have a relatively low probability of success (see figures 1 and 2). Bureau of Mines Study The Bureau compiled information from a variety of sources and found that the problem of AML fires is a serious one. Such fires can involve a high degree of hazard and can be difficult and costly to control. AML fires usually involve smoldering combustion in outcrops, waste banks, or abandoned mines. Given the nature of these fires, it is unlikely that the extent of the problem or the cost of solutions will decrease in the near future.

Jan 1, 1992

By Scott W. Hazen

This report presents the results of a statistical analysis of a limited amount of sample and assay data from a production panel in an open - pit phosphate mine in the Phosphoria formation in Idaho . A frequency distribution analysis is shown for the assays , sample interval lengths , and products of assay and sample interval length for the millshale , furnace - shale , and main phosphate beds . Correlation techniques were used to show the relationships between assays and sample interval lengths . Within- drill - hole and between - drill - hole correlation were also examined as a means of predicting grade trends in the ore . Simulation methods , utilizing a digital computer , were used to establish assay populations that could be used for estimating grade of ore , cutoff grades , and deposit or bed identification .

Jan 1, 1964

Provide a portable crushing capability to keep conveyor haulage close to the working face and permit more efficient and safer ore handling in low headroom, hardrock mines. Approach A readily portable jaw crusher is used which meets machine size, feed rock size, product size, and throughput requirements for low headroom, hardrock mines. How It Works The crusher is mounted on wheels to expedite frequent moves and to allow crushing of mined rock or ore near the working face. The crushed product is then placed on conveyor belts that are ex-tended as the crusher is moved. Keeping crushing and conveyor haulage near the face minimizes the haulage distances for trucks and loaders. Loading and haulage of run-of-mine ore is frequently the highest operational cost in underground mines. These costs can be significantly reduced by use of a belt conveyor, which is a common practice in coal and other soft mineral mines. The new low-profile hard rock crusher gives the same advantage of extensive belt haulage capabilities to low headroom, hardrock mines. The low-profile crusher will accept feed up to 30 inches when operating under 11 feet of headroom. The headroom required for crusher operation was reduced by tilting the jaws, feeding the crusher horizontally, and placing the eccentric shaft at the back or in a horizontal plane with the jaws. Material is fed by an

Jan 1, 1981

By Seth C. Schaefer

The Bureau of Mines studied thermodynamic properties of liquid Al-Si alloys with the high-temperature galvanic cell Al(1)//Al+3(AlC13 in NaCl?KCl)//Al-Si alloy(1). Activities of aluminum and silicon (referred to pure liquid metals) show a pronounced negative deviation from Raoult's law in liquid Al-Si alloys containing 0.9 to 35.2 atomic-percent silicon. Activity coefficients and the properties [?Gi, ?GxS ,?H, ?G, ?Gxs , and ?S] have been derived from the experimental data and are summarized in tables and illustrations.

Jan 1, 1974

Provide mine personnel with a convenient means of determining the optimum installation geometry of roof trusses in bedded roof. Background Mine operators frequently ask the following questions concerning roof truss installations: 1. Where should the bearing plates or brackets be placed or where should the inclined holes be started? 2. At what angle should the holes for the inclined chords or angle holts be drilled? 3. What tension should be put into the inclined chords so as to achieve the most effective results for the effort and expense? Truss hardware manufacturers have responded to these questions with answers based on what seems to work best. While designs based on past experience are frequently reliable, there was a need for a rational approach that could accommodate a variety of conditions. The Bureau has developed a procedure that enables mine operators to optimize roof truss installations in bedded roof.

Jan 1, 1989

By A. G. Kim

Coal formation begins in peat swamps or bogs, in which microorganisms alter plant material and initiate the formation of carbonaceous sediments. Methane, which constitutes about 98 percent of the hydrocarbon gas in coalbeds, is known to be a product of anaerobic microbial metabolism. To determine if other hydrocarbon gases could be produced in an environment similar to that of a swamp, samples of wood cellulose and lignin were inoculated with soil micro-organisms and incubated anaerobically. The resultant gases included methane, ethylene, propane, propylene, butanes, pentanes, and carbon dioxide. Hydrogen was also produced from the wood samples during the first month of incubation. Over 90 percent of the produced gas was methane; C02 was the other predominant component. Concentrations of all other hydrocarbon gases ranged from l to 20 parts per million, approximately 0.1 percent of the total hydrocarbons, which was less than the concentration in coalbeds. Therefore, although higher hydrocarbons could be produced in a swamp environment, subsequent mechanisms, either concentration by adsorption or formation during geochemical reactions, must affect the final concentration of higher hydrocarbons in coalbeds.

Jan 1, 1972

By Roy T. Sorensen

This Bureau of Mines report presents the results of a study to rank technologies for extraction of alumina from bottom ash and coal shale. The available literature on composition and availability of coal waste was reviewed, and papers pertinent to alumina extraction are referenced. Types of coal waste were categorized by method of waste generation, coal content (heating value), location, coal type (ash nomenclature), and alkaline earth content. The differences and similarities among the categories of coal waste are summarized as to factors that my affect aluminum extraction, especially factors concerning chemical composition, current production, storage problems, and accumulated tonnage. Data available on physical characteristics and mineralogy did not correlate well with the individual categories of coal waste, and discussion on these two aspects is limited to the differences between coal ash and coal shale.

Jan 1, 1983

By G. B. Atkinson

Properties of catalysts prepared from intermetallic compound precursors were investigated by the Bureau of Mines as part of its mission to decrease U.S. dependence on foreign sources for scarce catalytic materials, such as nickel, cobalt, and chromium. Methods were developed whereby catalysts with surface areas of 30 to 40 m2/g were prepared from intermetallic compounds. Activity of these catalysts for the methanation reaction and methanol synthesis was deter-mined using a fixed-bed, single-pass, flow-through reactor. Catalysts prepared from rare-earth-nickel intermetallics had specific activity for methanation that was five times greater than that of commercial catalysts and were equal to or better than commercial catalysts with regard to sulfur tolerance. Under identical reaction conditions, catalysts prepared from thorium-copper intermetallics produced more than 10 times as much methanol as a commercial low-pressure catalyst and exhibited a high degree of catalytic stability.

Jan 1, 1982

Early American history is filled with records of the search for and extraction of minerals-a Northwest passage to the treasures of the Indies-an overland route to the goldfields of California. Mining and its associated minerals industry have heralded advancing civilization throughout the ages. The two basic resources on which we all depend for our food, clothing, shelter, and other comforts are agriculture and minerals. Our endowment and how we use it; the spirit and industriousness of our people; our form of social organization all converge to make up our standard of living-our way of life.

Jan 1, 2012

By David Schlain, C. B. Kenahan, F. X. McCawley

The electrodeposition of protective coatings of tungsten from a sodium and lithium borate - tungstate - tungstic oxide fused salt electrolyte was investigated . Soluble tungsten anodes were employed . Deposits were made on molybdenum , Carpenter 20 stainless steel , Inconel , and nickel . An atmosphere of argon was maintained around the electrolytic cell , and the electrolyte was stirred by rotating the cathode . Thick deposits of tungsten (up to 26 mils ) were made at a temperature of 900 ° C and cathode current densities of 0.3 to 0.4 ampere per square inch with high current efficiencies . The effects of variations in temperature , current density , electrolyte agitation , and tungstic oxide content of the electrolyte and of the presence of impurities such as moisture , air , iron , and nickel were investigated .

Jan 1, 1964

By F. M. Carlson

Comparisons are made between the results of the Buckley-Leverett and Kern solutions, which describe immiscible displacement of oil by gas in a linear system and the results obtained from a less restrictive numerical model. This model takes into account the effect of compressibility of the oil and gas and the effect of allowing changes in the amount of gas in solution in the oil. These effects are best exemplified by imposing large pressure drops across the system. With these large pressure drops, comparison of the model solution with the Buckley-Leverett solution reveals that the Buckley-Leverett solution provides estimates of recoveries at breakthrough of the gas that are too low. In contrast to the model, the Kern solution predicts breakthrough recoveries that are too high. A modification to the Kern solution is presented to facilitate more accurate predictions of recovery at gas breakthrough for gas injection at pressures higher than the saturation pressure of the oil.

Jan 1, 1974

By Andrew B. Cecala, Edward D. Thimons

"The Bureau of Mines has recorded a number of different background dust sources that significantly contaminated the air breathed by bag machine operators. These background sources, observed at five different plants over the past 2 years, can expose bag machine operators to more significant dust concentrations than the filling process itself. To keep bag operator exposure within acceptable dust levels established by the Mine Safety and Health Administration, U.S. Department of Labor, the significance of these background sources must be realized, and the sources must be identified and controlled. The purpose of this work is to identify common background dust sources and show the significant effects that they have on the bag operator's overall dust exposure. INTRODUCTIONThe purpose of this report is to identify some common background dust sources in and around the bag-filling area. Although these background dust sources are of ten unrecognized, they can be more significant sources of contamination than the dust generated from the bagging process.The bagging of mineral products into 50- and 100-lb paper bags is common throughout the entire mineral processing industry. Bagging is performed by a bag operator who sits in front of a two- or four-station fill machine. The bagger's function is to attach empty bags to the fill nozzles as filled bags are ejected from the machine. If the product being bagged is extremely fine (smaller than 200 mesh), the bag operator's dust exposure is usually one of the highest in the plant.The bag operator is exposed to two primary dust sources. The first is product blowback during the bag-filling cycle. This occurs as excess pressure is released from around the fill nozzle during filling. As the excess air forces its way out of the bag, product is forced out with it. This blowback of product leaving the bag creates a considerable amount of dust. The second major source is the ""rooster tail"" of product thrown from the bag valve and fill nozzle as the bag is ejected from the fill machine. Since the bag is pressurized as it leaves the machine, product spews out of the valve for a few seconds."

Jan 1, 1986

To develop an in-mine water treatment system in which bacterial sulfate reduction and limestone dissolution continuously remove metals and acidity from contaminated drainage. Approach A section of mine tunnel was converted into a water treatment bioreactor by constructing cinder block dams and fang the area between them with a porous substrate mixture of limestone gravel and compost. Readily fermentable materials such as dairy whey, spent brewing yeast, or sugar were periodically added to the reactor. Mine drainage was impounded behind one of the dams and continuously percolates through the reactor substrate at a controlled rate. How It Works The reactor substrate soon becomes anaerobic after it is saturated with mine water. Under anaerobic conditions, sulfate-reducing bacteria consume the organic materials that are added to the reactor and generate hydrogen sulfide (HIS) and alkalinity. The H2S reacts with dissolved iron and heavy metals to form metal sulfide precipitates. The alkalinity raises the pH of the water and induces aluminum to hydrolyze and precipitate as aluminum hydroxide [Al(OH)3]. Additional alkalinity is generated by the continuous dissolution of the substrate limestone. Metal sulfide precipitates and Al(OH)3 are retained within the reactor, and the treated water is discharged. The underground location of the system allows year round operation.

Jan 1, 1994

By R. L. Wise

Heat content studies were conducted on burned shale, spent shale, and three grades of raw oil shale from the Green River Formation. Corrections were made for product enthalpies. The results were compared with previous work, indicating good agreement below retorting temperatures, but some differences at retorting temperatures. A general equation was developed relating heat content to oil-shale grade and temperature.

Jan 1, 1971

Develop new technolgies and techniques which enable recovery of strategic and critical minerals such as cobalt from domestic resources, thereby easing the U.S. dependence upon foreign producers for these valuable commodities. Approach The Bureau of Mines, through research, developed a process which uses mineral beneficiation techniques to recover cobalt-rich products from Missouri lead ores. Before development of this process, cobalt was lost as an impurity in the copper, lead, and zinc concentrates and in the mill tailings because the technology to recover it with minimum impact on present production did not exist.

Jan 1, 1989

By L. Mark Irwin, R. A. Marsyla

The objective of this laboratory investigation was to develop a mattesmelting process for the recovery of copper from industrial smelter dusts . Experimentation was conducted on three samples of Cottrell precipitator dust from a northern Michigan smelter with variations in the following conditions : Temperature , charge composition , pelletization , and moisture content . Based on chemical analyses of the furnace slags , poorest recovery of copper was effected in smelting dry charges regardless of composition . Some improvement was noted with uniformly moistened charges and still more with pelletized (but dry) mixes , but best results were obtained from smelting moist , self - fluxing pellets . Under favorable conditions , experiments yielded furnace slags with an average copper content of only 0.15 percent , which is well below that of industrial copper reverberatory slags .

Jan 1, 1963

Provide an accurate, simple, alternative means of evaluating the safety of mine electrical ground systems which has little or no negative impact on mine productivity. The Traditional Evaluation Method The Code of Federal Regulations requires all mines to safely ground their power systems to earth. Effective earth grounding reduces shock hazards to mine workers operating electrical equipment, protects equipment from damage by voltage transients, and provides a means of detecting and locating ground faults. Once an earth ground bed has been constructed, its level of resistance has traditionally been used to gauge the safety of the entire grounding system. Bed resistance measurements are normally performed using a ?fall of potential? technique with a current return electrode placed at a remote location, If the resistance measured is acceptably low, then the bed is assumed safe.

Jan 1, 1985

Provide a central source of subsidence reference in formation for industry, academia, and government agencies interested in improving subsidence prediction and analysis under U.S. mining conditions. Approach Develop a comprehensive bibliography about mining related surface subsidence and store this information in a computer file. Make specific references accessible through a key word retrieval program. Supplement these key word identifiers by entry of author's name, title of publication, subject of text, or sponsor of publication. How It Works Requests for subsidence in-formation are made by phone or mail to the Bureau of

Jan 1, 1982

Develop a down-hole replaceable diamond core bit that will reduce overall drilling costs and increase total available drilling time per hole. Approach A one-piece diamond core drill bit of unique geometric shape has been designed, fabricated and field tested. The bit can be withdrawn (or replaced) from the bottom of the well-bore without removing the drill rods from the hole, saving a significant amount of non-productive drilling time. How It Works The replaceable bit system consists of two basic subsystems: the removable core bit, and the equipment necessary to replace the wornout bit without pulling the drill rods out of the hole. The geometric configuration of the bit is that of a one-piece diamond studded cutting element created by "slicing off" two parallel sides of a conventional diamond cone bit. This geometric configuration, along with some minor modifications to the outer core barrel, allows the bit to be rotated in two planes and, with the retraction-insertion tools, raised or lowered through the interior of the drill rods using a conventional wire-line system. For example, to retrieve the bit, a retraction tool is lowered through the drill rods using a conventional wire-line system and at the hole bottom, the tool automatically orients itself within the outer core barrel.

Jan 1, 1981

By Richard O. Kneisley

Microseismic activity observed in both the laboratory and underground indicates that a quiet period, associated with the closure of existing fractures and strongly influenced by coal seam microstructure, occurs prior to coal bumps. Field studies conclude that coal mine bumps occur against a background of this so-called microseismic calm. This Bureau of Mines report summarizes microseismic activity associated with face bumps and floor bursts in a deep, western U.S. coal mine. Results conclude that while bumps are often accompanied by panel-wide increases in microseismic activity, bumps are not only preceded by a localized decrease in activity, but occur within these quiet zones. The results of this study concluded that microseismic activity may be applicable to the global detection of potential bump-prone zones, but that future studies are necessary to confirm these findings and to improve the techniques for evaluating stress control effectiveness.

Jan 1, 1989