Search Documents

By J. M. Stuve

A novel calorimetric solution technique, recently developed at the Bureau of Mines, was tested using synthetic samples of chalcocite (CU2S) and covellite (CuS). The solution of these refractory sulfides was accomplished by oxidation with bromine in a moderately acidic, aqueous solution. The resulting values for the standard enthalpies of formation (?Hf°, 298.15) for CU2S(c) and CuS(c) were -18.1 ±1.1 kcal/mol and -13.3 ±1.1 kcal/mol, respectively. These values are in good agreement with published formation values derived from other methods of physicochemical measurement.

Jan 1, 1982

To find solutions for common safety problems encountered in the handling of trailing cables, based on observations at many different surface mining operations. Approach Practices in handling trailing cables were Investigated through personal visits to over 40 mines, supplemented by visits to cable manufacturers and cable repair service companies. The most effective solutions to the safety problems en-countered were noted and are described In the project final report. Examples are given in this Technology News. Accident Experience Most cable-related injuries occur as a result of workers lifting, pulling, tripping, or being struck by the cable. The Table gives the frequency of occurrence for injuries reported during a recent 3 1/2 year period.

Jan 1, 1982

By Margaret M. Ragin

In a cooperative effort between the U.S. Bureau of Mines and the Florida Institute of Phosphate Research, with input from the phosphate industry, the conversion of phosphogypsum to sulfur has been investigated. The first step in the conversion scheme involves reduction of phosphogypsum to calcium sulfide. Effects of temperature, catalyst, reaction time, and type of reductant (carbon monoxide and coal) are discussed. It was determined that phosphogypsum could be reduced to calcium sulfide at 850° to 1,000° C using either coal or carbon monoxide as the reductant. The required temperature was lowered to 750° C using ferric oxide or magnetite as a catalyst for the reduction reaction. Results indicate that as the volatiles content of the coal is increased, reaction temperature may be decreased to obtain a given conversion, or if the reaction temperature is maintained constant, the conversion can be increased. Best results were 95- to 100-pct conversion using a high-volatile coal at 800° to 850° C. Addition of a catalyst increased calcium sulfide yield when low- or medium-volatile coals were used as reductants, but had little effect when high-volatile coals were used.

Jan 1, 1990

By Fred C. Turin, Jasinder S. Jaspal, Alan G. Mayton, William J. Wiehagen

This report describes serious injuries occurring to bulldozer operators working at U.S. coal, metal, and nonmetal mines. The period covered is 1988-97. The data were collected by the Mine Safety and Health Administration (MSHA). A total of 873 injury records are examined. These injuries resulted in 18 fatalities and 31,866 lost workdays. All of these injuries occurred to dozer operators while they were doing common production tasks. An injury classification system was developed to code the narrative information that describes the circumstances surrounding the injuries. Injury records are categorized by activity (task being done), incident result (what apparently happened to the dozer), and operator impact (how the operator was injured). Where information is available, contributing factors are identified. This classification system supplemented the standard injury/illness data classification system compiled by MSHA. The results of the study indicate that, from 1993 to 1997, the number of serious injuries to dozer operators declined by 30%. The reduction in serious injuries was accompanied by a decrease in days lost due to injury. Although the number of reported injuries has decreased, dozer operators being jolted and jarred accounts for the largest percentage (70% of the incidents) and severity (75% of the workdays lost) of serious injuries while operating the equipment. Vertical jars (while backing up the dozer) resulting in injury to the operator accounted for a sizable percentage of jolting and jarring injuries. Working near an edge carries significant risk for fatal injuries. Of 116 incidents where the dozer fell over an edge, rolled over, or fell into a hidden void, 14 (12%) resulted in fatal injuries. In cases where the dozer operator either jumped or was thrown out of the cab in a fall over or rollover, 7 out of 26 were killed. Overall, 80% of the fatalities occurred while working near an edge or hidden void or on a steep slope. Further reductions in injury risk will require more widespread use of seatbelts, field and laboratory research interventions to better assess the effect of alternative engineering (e.g., seat and seat suspension) designs to dampen or isolate the effects of shock and vibration, and continued focus on hazard awareness, recognition, and response.

Jan 4, 2001

By W. K. Overbey

Knowledge of fracture systems in oil or gas reservoirs is essential to the efficiency of both primary and secondary production operations. A relationship was established between structural features of the surface and both natural and induced fractures in oil and gas reservoirs, thus providing a method of predicting the direction of rock fracture prior to field development and well completion. Correlations between the surface features and under-ground fractures resulted from analysis of joint strike measurements, bottom-hole impression packer surveys, photographs of hydraulically fractured wells, fracture data from oriented cores, in situ strain measurements from formation outcrops, and lineament analyses from aerial photographs. The mean orientation of surface fractures, lineaments, and stress field directions ranged from N 53° E to N 73° E, compared with an average orientation of N 63° E for the hydraulically induced fractures. Tectonic stress field was shown to influence the direction of hydraulically induced fractures. This report presents the details and application of techniques to obtain the orientation of the principal horizontal compressive stress field component and thus the direction of induced fractures.

Jan 1, 1971

By Richard Hammer

Various alternating current (ac) methods can localize faults in mining power cables. Several methods considered by the Bureau of Mines in this report are the Murray loop for short circuits, wherein a bridge provides proportional distance to the fault; capacitance measurements for open conductors; inductance measurements for shorted conductors; phase comparison, high speed recordings of voltage and current in the faulted state are compared with normal voltage and current with the difference being a function of impedance change and impedance change being a function of fault location; and standing wave measurements, detecting the resonance of the length of cable to a fault (either short or open). Portable capacitance bridges are presently available for the second method, and the fourth method is well developed for use on large power distribution systems. Because it utilizes pulses rather than ac, the time domain reflectometer (TDR) method of fault locating was not included in this investigation. However, a comparative evaluation between this versatile method and the Murray loop might prove advantageous in locating high resistance faults.

Jan 1, 1977

By William J. Wiehagen

This is the third in a series of four articles that discuss underground fire-fighting preparedness. As with the first two articles, it is based on interviews with 214 miners conducted at 7 underground coal mines (referred to as Mines ?A? through ?G?) by researchers of the National Institute for Occupational Safety and Health?s (NIOSH) Pittsburgh Research Center [Vaught et al. 1996]. In the first article, the authors presented an overview of the study conducted by NIOSH on mine fire response preparedness and provided a general perspective on underground mine fires. The second article discussed miners? preparedness to evacuate a fire and their experience with incipient fires. In this article, we describe miners? experience in fighting underground mine fires and present their perceptions of training and readiness for fire-fighting.

Jan 1, 1997

Provide reasonably priced, reliable fire protection for AN-FO haulers. Approach An automatic fire sensing and suppression system for AN-FO haulers was developed and on-vehicle tested. How It Works The system works in two ways to protect personnel from dangerous and unpredictable AN-FO fires. First the system senses and suppresses fires on the truck before they spread to the AN-FO in the bunker. This design was chosen because AN-FO truck fires generally start when combustible liquids (such as diesel fuel, hydraulic fluid or lubricating oils) are ignited by hot surfaces mainly on three areas: the engine, the transmission or the power take-off. These fires are quickly sensed by a linear temperature sensor strung throughout these three areas. The system then warns the operator and automatically suppresses the fire by discharging 30 pounds of multipurpose dry chemical extinguishing agent through a network of fixed hoses and nozzles. Second, this system includes six spot thermal sensors mounted inside the bunker on the truck to monitor the AN-FO temperature in case a fire does spread to the bunker area. If the bunker temperature rises to 190° F, a loud siren is sounded to warn nearby per-

Jan 1, 1981

By S. J. Anderson

The Bureau of Mines compared three methods of rock cutting using drag cutters under controlled laboratory conditions. The methods tested were the conventional drag cutting method used on continuous miners, the kerf-core method used on some boring machines, and an experimental method called ripper cutting. All three methods were tested in blocks of Indiana and Kasota limestone. The results of this testing showed ripper cutting to be 30 to 40 pct more energy efficient than both the conventional and the kerf-core methods in Kasota limestone and 35 pct more efficient than the kerf-core method in Indiana limestone. The conventional method was, however, 9 pct more energy efficient than the ripper method in Indiana limestone. These results are considered promising, and more tests are planned with the ripper cutting system.

Jan 1, 1987

By W. S. Sanner

Grinding experiments were conducted to determine the finest anthracite particles that could be produced in a ball mill. Continuous and batch tests were run in a dry-grinding ball mill. Batch grinding produced the finest coal particles. They averaged 2.2 microns in diameter and were 99.0 percent smaller than 37 microns. Continuous grinding yielded a product 6.1 microns in diameter, with 96 percent smaller than 37 microns.

Jan 1, 1968

By Forrest T. Moyer

THIS CHAPTER of the Minerals Yearbook contains injury experience and related employment information for the coal-mining, coking, oil and gas, peat, and native asphalt industries in the United States for 1962. Injury experience is measured by the number of injuries sustained per million man-hours of exposure in each industry. No attempt has been made to combine these data and present rates reflecting the mineral-fuel industries because the hazards of the separate industries are not comparable. Tabulations showing the trend of injuries and employment for all mineral industries are presented in volume III of the Minerals Yearbook. COAL The injury-frequency rate for the coal-mining industry of the United States increased less than 2 percent, according to reports received by the Bureau of Mines. The number of fatal and nonfatal injuries per million man-hours in 1962 was 45.86, based on final data for anthracite mines and preliminary data for bituminous coal and lignite mines.

Jan 1, 1963

By James S. Browning

Domestic production of lithium minerals, source of the lightest metallic element, has increased from an average of 1,327 short tons of concentrate in the 1935-39 period to approximately 37,830 short tons in 1954. This rather phenomenal growth in production and use reflects growing industrial interest in the metal and its salts. This information circular has been prepared to summarize for the casual technical reader the reserve, mining, processing, and consumption situation pertaining to the mineral spodumene - the principal source of lithium. A relatively complete bibliography is included for those who may need more detailed information.

Jan 1, 1958

Determine what diameter piping is necessary to obtain sufficient water flow to spray nozzles used for dust suppression. Approach A simplified, diagrammatic method of calculating the flow of water through a proposed system consisting of a supply line and two banks of spray nuzzles is outlined. How It Works The pressure versus flowrate of the supply at the tapping point must be known or measured. The supply curve of typical city water at a 1 ¼ -inch pipe outlet is shown by the lowest curve in Figure 1. A supply curve for a typical pump fed from an open sump is shown by the middle curve. The combination of these, the supply curve of a pump fed by the city water supply is shown by adding the lower two curves to get the upper curve. A pump supply curve showing flowrate versus pressure is usually supplied by the manufacturer. The water supply line flow curve can be determined by measuring the time required to fill a 55 gallon barrel at various valve settings to determine flow, and by measuring corresponding pressures at the valve with a gauge.

Jan 1, 1979

Remotely monitor overburden response to longwall mining using time domain reflectometry (TDR) and a combination of hardware and software, as part of the U.S. Bureau of Mines (USBM) program to characterize subsidence. Background TDR was developed in the 1960's as a method to locate, discontinuities in coaxial transmission cables. In this method, voltage pulses sent along a cable are reflected by cable defects. The pulse reflections are used to determine the type and magnitude of the defects. The TDR concept was extended to material property measurement by embedding cables into particular materials and evaluating the cable's dielectric behavior as material properties were modified. This technique was adapted by the USBM in 1978 for use in monitoring rock movement during underground mining. The same concept is utilized today. A coaxial cable is grouted into a rock mass that is expected to deform. Progressive rock movement causes the cable to deform, as shown in figure 1, and changes to occur in the cable's electrical properties, which then produce changes in TDR reflection signatures. The technology has advanced to the point where it is now possible to distinguish shear deformation from tensile deformation and to quantify rock mass displacements by analyzing the TDR signatures.

Jan 1, 1995

Analyze variably saturated flow in mining and other environmentally sensitive settings through the use of personal computer (PC) based software. The Problem There is an increasing need for mining companies to quantify water contaminants and their migration in the unsaturated zone. New and innovative computer models are therefore necessary to more accurately assess the potential impact of mining activities on groundwater resources and the environment. Applications for unsaturated flow modeling include (1) assessment of the impact of surface or underground extraction mining on flow conditions; (2) assessment of various hydrologic designs for resource recovery, such as in heap leaching or in situ leach mining; (3) assessment of the transport of conservative nonrcactive constituents in response to migration from spoil piles, or acid mine drainage; and (4) assessment of any combination of the above to facilitate expeditious permitting for mining operations. Since the mid 1970's there has been a proliferation of mathematical models and procedures for solving unsaturated now problems; however, few of these approaches have been integrated into software for public use. Commercially available unsaturated flow software models typically are limited to a single application and have restricted approaches. For example, computer codes that solve the unsaturated flow problem based on an analytic expression arc restricted to a simple geometric shape, homogeneous and isotropic materials, and provide only information regarding pressure and flow conditions in specified wells. The variably saturated computer codes that take advantage of the finite difference or finite element approach arc often restricted to either steady state or transient solutions; utilize one specific moisture-retention relationship and moisture-dependent permeability function; do not account for hysteresis; and are used with specific hardware such as a mainframe or work station. This restricts their use because they arc hard to interface, and arc often poorly documented, support dependent, and expensive. The mining community needs a flexible, more broadly based, variably saturated fluid flow simulator for the PC-platform to more accurately predict fluid movement in the mining environment.

Jan 1, 1991

Improve the field-of-view into the front-right blind spot for drivers of large haulage trucks, thereby reducing the growing collision hazard in surface mines. Approach Reduce the glare problem found in the first generation fresnel lens blind area viewer design by eliminating the upward-looking section of the fresnel lens and adding a rear hood to reduce backlighting. How It Works The first generation blind area viewer was developed and in-mine tested as an aid to improved visibility for large haulage trucks. Other aids were improved left-and right-hand mirrors. Evaluations showed that a blind area viewer mounted on the right-front of the radiator deck was effective and was readily accepted by drivers. Nevertheless, because glare was a problem under certain conditions, a low-profile viewer was developed. Glare control louvers from the earlier design were kept and a backlighting glare control hood was added. The height of the hardware was reduced by eliminating the top three inches of the fresnel lens. This portion of the lens contained an upward-looking segment which originally was thought to be needed so the driver could see the horizon when he looked through the viewer and be better

Jan 1, 1982

By John H. Scott

At the request of the Mine Safety and Health Administration, U.S. Department of Labor, the Bureau of Mines evaluated the model BT 300 C-D blasting machine tester, manufactured and distributed by Research Energy of Ohio, Inc. (REO), to determine whether the tester performed as stated by the manufacturer and responded satisfactorily to electrical faults introduced into the blasting machine circuit. Tester readings were recorded for 13 blasting machines and for 12 circuits constructed to simulate the electrical parameters of actual machines. The tester readings were acceptable for all of the blasting machines, although the switch position assigned to one machine produced an off-scale reading. The tester responded satisfactorily to the simulated circuits and detected serious voltage or capacitance faults when they were introduced. However, it did not respond accurately to certain resistance faults. Temperature tests were also made, and the tester performed equally well at temperatures of 20°, 42°, and 81° F. This tester was judged a useful accessory for field checking blasting machines for defective batteries and capacitors, despite its limitations. It is recommended that the tester manufacturer specify the lowest acceptable reading at which a blasting machine may be used and below which the blasting machine should be returned to the laboratory or manufacturer for maintenance.

Jan 1, 1981

By Fred N. Kissell

The new MSHA diesel rules have stone mine operators looking hard at pos¬sible upgrades to their ventilation systems. There are existing methods to reduce diesel engine emissions (MSHA, 2001)(Head, 2001b),but many operators will decide that a ventilation upgrade is necessary is well. NIOSH hay several stone mine ventilation projects underway, but in the meantime a good information resource is the work done by the U.S. Bureau of Mines in the 70's and 80's on ventilation for oil shale mines. The Bureau conducted this research because oil shale mines were projected to be gassy and would, therefore, require a lot of ventilation air. The focus of this oil shale work was on the use of jet tans for lace area ventilation, and on stoppings that would he low Lost and leak-tight. The work also considered changes in mine design to reduce the number and size of stoppings. The findings are still applica¬ble to stone mines.

Jan 1, 2002

By Edward A. Barrett, Lynn L. Rethi

From 1987 through 1996, 13 fatalities occurred at underground operations in the U.S. stone mining industry. A review of the underground limestone mine industry data for this 10 year period indicated a high fatality concentration in one area: ground failures.

By P. W. Jeran

The Beckley mine is one of five new mines in a heretofore unmined portion of the Beckley coalbed. The remoteness of these new mines from prior mining and their greater overburden preclude applying methane emission experience obtained in the old mines. Four sections of the Beckley mine were monitored. The data gathered show that variations in methane emission cannot be explained by variations in coal production. Although overburdens varied by as much as 30 pct, no correlation with methane emissions could be determined. The rib emissions increase with increased length of rib from a section advancing into virgin coal and do not decline over a prolonged idle period (32 days) whereas some decline has been measured for a section not mining into virgin coal. The indication is that degasification prior to mining will reduce the hazard of methane emissions in this area of the Beckley coalbed.

Jan 1, 1977