Search Documents

By Lloyd A. Morley, Robert Stefanko

Before going directly to the analysis, it would be good to summar¬ize explosion-proof container approval methods. Both Magison (52) and Short (84) state that in general practice, the systems are certified for: 1. a rugged enclosure able to withstand an internal explosion but not allow explosively hot gases to escape, and 2. maximum surface temperature, with equipment operating inside, that will not ignite the surrounding atmosphere. Also, testing insures that any material in contact with the container surface will not be ignited by a hot spot. Associated with the first practice, the enclosures are inspected for: 1. a safe flange gap width, 2. a pressure increase during ignition, and 3. an hydrostatic pressure withstand level. The hydrostatic pressure level is almost always determined by a meas¬ured ignition-pressure test and is usually applied to prove the mechan¬ical design to some safety factor. Consequently, explosion-proof enclosure testing includes temper¬ature, permissible flame gap, and pressure. Specifications and prev¬ious research also can be similarly separated even though some interre¬lation exists between the flame gap size and internal enclosure pressure during an explosion. The Schedule 2G Sections applicable to these subjects are: 1. 18.2 Definitions; 2. 18.6 Applications;

Jan 1, 1974

By J. L. Konchesky

The Bureau of Mines investigated the main reactions of coal gasification by steam. Coal (minus 70 mesh)-water slurry was fed into a laboratory-scale tube-coil gasifier to show the effects of residence time (0.6 to 1.1 sec), steam-coal ratio (2 to 11 lb/lb), and temperature (1,600° to 1,900° F), at about 1-1/2 atm. Devolatilization was very rapid: about 70 pet of the coal's volatile matter evolved within 0.6 sec at about 1,600° F; temperature increase released more volatile matter until about 95 pct was driven off at 1,900° F. Devolatilization was not increased by raising steam concentrations and was only slightly increased by extending residence time. Below 1,600° F, there was no evidence of the steam-carbon reaction, but at 1,900° F more than 80 pct of the coal's fixed carbon was converted to gas; the conversion was increased Significantly by increased residence time and steam concentration. The water-gas shift reaction occurred simultaneously with devolatilization, and the steam-carbon reaction, approaching equilibrium with increased residence time and temperature and decreased steam concentration.

Jan 1, 1969

By Richard A. Thomas, Charles D. Litton, Kenneth E. Mura, Harry C. Verakis

Experiments were undertaken to evaluate the flammability of typical noise abatement materials used to line the cab interior of mobile mining equipment. The experiments were conducted using three different experimental configurations: 1. A ventilated tunnel test. 2. A full-size cab test where the interior surfaces were lined with the sample material and then ignited near the floor using a methane-air burner. 3. Standard ASTM E-162 tests using a radiant panel test apparatus. This paper describes the tests and presents the results obtained for 15 to 20 different materials of various chemical compositions and thickness. With one exception, materials that did not exhibit flame spread in the tunnel test also performed well in the full-scale cab test. All materials that had passed only a small-scale flammability test, such as SAE J369, failed dramatically in all three of the above test configurations. With one exception, all materials that performed well in the full-scale cab test had flame spread indices < 25, based upon the ASTM E-162 results. The lone exception had an ASTM E-162 flame spread index of 68. With regard to samples that failed the full-scale cab test, the carbon monoxide levels within the cab reached lethal concentrations in the range of 1.8% to 3.8% within 2 minutes from ignition of the sample—dramatically illustrating the severe fire environment that can result within the cab space.

By P. W. Jeran, M. C. Irani, D. H. Lawhead

The Beckley mine is one of five new mines in a heretofore unmined portion of the Beckley coalbed. The remoteness of these new mines from prior mining and their greater overburden preclude applying methane emission experience obtained in the old mines. Four sections of the Beckley mine were monitored. The data gathered show that variations in methane emission cannot be explained by variations in coal production. Although overburdens varied by as much as 30 pct, no correlation with methane emissions could be determined. The rib emissions increase with increased length of rib from a section advancing into virgin coal and do not decline over a prolonged idle period (32 days) whereas some decline has been measured for a section not mining into virgin coal. The indication is that degasification prior to mining will reduce the hazard of methane emissions in this area of the Beckley coalbed.

Jan 1, 1977

By BUREAU OF MINES

LIST OF PUBLICATIONS ON CERAMIC INVESTIGATIONS U.S. BUREAT OF MINES .

Jan 1, 1923

By Pablo Velasco

Ecuador had limited mineral output, al-though the Government attempted to stimulate metallic mineral exploration and also evaluated a gypsum and a phosphate deposit. A pilot plant to exploit gold deposits was established, and there was extensive gold exploration activity in southern Ecuador. Domestic output of iron and steel declined sharply. Among all minerals, petroleum output was the dominant factor with both exports and production increasing significantly over that of 1988. Crude oil exports contributed 63% of total export earnings and about 70% of the central Government&apos;s revenue.

Jan 1, 1986

By Barbara J. Halpern

There?s no denying that mining is a male-dominated industry. Yet thanks to technologies developed over the last 20 years, societal changes in sex role stereotyping, individual determi­nation, and the willingness of companies to train women, there are no jobs in mining today where women are not represented. Women are drillers and electricians as well as drivers of heavy equipment and haulpack trucks. They perform jobs ranging from field exploration and metallurgy to clerical and janitorial and warehousing positions, from prospectors and underground blasters to geologists and land reclamation experts, from communicators to legal experts on mining law and more. The Women?s Mining Coalition, founded in 1994 to shepherd responsible legislative mining reform, estimates that 20 percent of the workers in the mining industry are women. Although women are concentrated in clerical and adminis­trative jobs, at least 10 percent are in non-traditional, hardhat jobs, claims the group. There are women in management, but the numbers in senior management remain small, especially in larger companies.

Feb 1, 1998

By Mark A. Ackerson, Kenneth E. Hjelmstad

An ideal fire warning alarm system for underground mines would be low cost, convenient, fast, reliable, and able to warn all underground workers. Present warning systems, such as phones, messengers, and stench, fail one or more of these criteria. The U.S. Bureau of Mines may have devised the ideal system. The one way communication system employs a large loop antenna and transmitter to create a 630 hertz (Hz) electromagnetic field to send information through-the-earth to cap lamp battery mounted micro- receivers worn by underground miners. Field tests of prototype equipment in 1986 resulted in through-the- rock signal transmission of over 762 m (2500 ft). Subsequent hardware upgrades for more recent tests resulted in transmissions of over one mile. Recently developed receiver circuitry employs phase- locked-loop detection circuitry responsive only to a specific series of pulses of given time duration, that eliminates false alarms from electromagnetic noise emitted by mine equipment, power lines, or lightning. A multichannel system can relay standard messages to miners

Measure the daily exposure of individual miners to alpha particles emitted by radon daughters (radioactive decay products of the radon gas present in the mine atmosphere). Approach A dosimeter worn by a miner counts alpha particle emissions from radon daughters, RaA (Polonium 218) and RaC (Polonium 214), collected on a filter, and stores the gross count for later readout. How It Works A pump draws air into the detector assembly where radon daughters are collected on a filter. The detector, a solid state surface barrier type, is mounted in the filter head behind a thin mylar disc which serves as a moisture barrier. When a radon daughter decays and its alpha emission strikes the detector, the alpha particle causes a pulse of electrical charge in the detector. The circuits used to condition and count the electrical pulses generated in the detector are represented by the other blocks shown in the simplified block diagram. Each pulse is first amplified.

Jan 1, 1979

By L. C. IlsLey, E. J. Gleim

The extensive use of pulverized coal for fuel in industrial plants has brought to the front again a question that heretofore has been considered only a mining problem, namely, " Can coal dust be ignited by an electric arc ? " If it can be so imited, the next logical query is , "under what conditions can such ignition occur ? " In view of the new problems relating to pulverized coal installations , and because of occasional mine disasters attributed to ignition of coal dust by electric arcs , it seems advisable to review the work done by Thornton and Bowden with electric flashes in coal dust , and to report two preliminary investigations conducted by the Bureau of Mines .

Jun 1, 1922

By L. D. Tracy

"Introduction In the course of the investigations by the Bureau of Mines into the various causes of coal-mine explosions, the fact that several gas explosions had occurred during or very soon after a mine was being un-watered, attracted the attention of the Bureau's engineers. The apparent coincidence was so marked that there appears to be an extra hazard present, whenever water, which has been standing against the face of the coal for some time, is suddenly removed either by natural drainage or by mechanical means.Actual Occurrences Case 1. - A typical illustration of this hazard is shown in a gas explosion which occurred in a mine in Central Pennsylvania. Four main entries, 50 feet apart with an average grade of 6 per cent, had been driven with the dip of the coal, and from these mains 7 pairs of entries, at intervals of 800 feet, had been turned at such an angle that their grade was slightly rising. Prom these latter pairs of entries, rooms were turned practically at right angles.The main entries had been driven for 4,500 feet and at the face there was 400 feet of cover. As far as could be observed, the roof was of sandstone and the floor of clay.The coal bed being mined was the Lower Kittanning, which has a thickness of about 4 feet. A typical analysis of the coal in that section is as follows:"

Oct 1, 1924

By J. D. Marchant

In the spring of 1953 a series of heats were made using a 3-phase, size ST, Pittsburgh Lectromelt arc furnace to develop a method suitable for melting, refining, and granulating cobalt powder produced by the Calera Mining Co., at Garfield, Utah. According to specifications stipulated by General Service Administration, the granules had to pass a 2-inch screen and be retained on a 6-mesh screen, be low in phosphorus and sulfur, and contain a minimum of 98.7 percent cobalt plus nickel. Various combinations of water temperature, water jets, and rate of pouring were tried early in the campaign to produce desirable granules. It soon became evident that a properly refined and deoxidized molten bath was the major requirement for a satisfactory product. The physical characteristics of the granules were improved also if, just before pouring, the surface of the molten metal bath was pre-pared by a method involving the use of silica flux. The Bureau processed 107,750 pounds of cobalt powder. A total of 104,810 pounds of cobalt granules meeting General Service Administration specifications was returned to the producer. The refining slag, which was also returned to the company, contained 1,781 pounds of metal.

Jan 1, 1955

By Andrew B. Cecala, Robert J. Timko, Alexander D. Prokop

Bag loading and stacking processes are the highest dust-exposure job categories in the metal/nonmetal mining industry.1 To cost-effectively decrease respirable dust levels, the Pittsburgh Research Center of the National Institute of Occupational Safety and Health (NIOSH), formerly of the U. S. Bureau of Mines, designed and tested a system called the Bag and Belt Cleaner Device (B&BCD). [ ]

By Donald R. Johnson

Apparatus developed by the Bureau of Mines for thermal analysis of oil shale was used to determine the thermal properties of shortite. Dissociation of shortite near 470° C occurs as an endothermic reaction that could consume significant quantities of heat in the oil-shale retorting process that produces shale oil. The shortite dissociation products undergo other thermal reactions that would not affect the retorting process. These reactions include crystal inversions near 365° C and 425° C and melting and decomposition endotherms above 500° C. Two separate reaction route for fusion and decomposition of the shortite decomposition products are dictated by the presence or absence of CO2 around the sample.

Jan 1, 1974

Improve the safety of salt mine workers by providing a means for quickly identifying areas within the mine that?s how an increased potential for gas and salt outbursts. Approach Outbursts occur in salt mines when a high-pressure pocket of gas is intercepted during the mining process, resulting in a sudden and sometimes catastrophic expulsion of gas and salt. In one case, the amount of gas released through such an event caused an explosion that resulted in five fatalities. The U.S. Bureau of Mines has designed and developed a gas outburst prediction system that can quickly determine the potential instability of areas within rock salt mines. The determination is based on noise measurements obtained from samples of the salt as they are dissolved in water. This system improves upon technology currently available because it provides information in only a few minutes instead of in several days. In addition, present prediction systems are not only time consuming, but expensive because they require laboratory conditions and highly trained personnel to operate them and determine results.

Jan 1, 1989

Reduce mine worker dust exposure by capturing airborne coal and quartz dust generated by a continuous mining machine. Approach Install a water-powered scrubber system operating at 1,000 psi on the side of a continuous miner boom. Dusty air under the boom is drawn through the scrubber, and cleaned air is discharged into the face return. How It Works Most coal mines use exhaust face ventilation to send fresh air over the miner operator, and contaminated air behind the line curtain to the section return. The difficulty with exhaust face ventilation is that the line curtain should be within 10 feet of the face for maximum effectiveness. If the line curtain is not extended properly, or water sprays for dust control are poorly installed, dust rolls back toward the operator. A scrubber mounted on the mining machine will effectively reduce this dust rollback and the dust in the return airstream.

Jan 1, 1989

By R. D. Ladoo

"At the beginning of 1920 a general feeling of optimism was noted in many talc-producing districts. The industry seems to have recovered from the temporary depression of the first half of 1919 and many mills are running at capacity production with their entire output for 1920 contracted for. The imports of talc for 1919 were only slightly larger than in 1918 by weight and probably no more by value. Thus foreign competition has not begun to be seriously felt. Several new companies in this country have been organized, some to operate new deposits and others to continue the work done by others.An interesting phase of the present situation is the possibility of increased use of talc in paint. There is a shortage of barium sulfate used as,paint filler. Since, for some uses, talc is considered second only to BaSo4 as a filler for paint, it is possible that part of the shortage could be relieved by an increased use of talc.A series of physical tests upon all pigment materials used in the manufacture of paints is being conducted for the Paint Manufacturers Association of the United States. It is important that all types of talc be represented in these tests. Producers of finely ground talc, 200 mesh and finer, are urged to submit samples of at least two pounds each of these grades that are available to paint makers with trade name and quality data, to the Institute of Industrial Research, 19th & B Streets, Washington, D. C., where the tests are being conducted.The Talc Products Company, Inc., Washington Building, Los Angeles, California, has recently been organized to develop a large body of talc one mile north of Riggs, San Bernardino County, California, This deposit contains a compact, white talc which can be sawed into crayons. The company's mill, at Los Angeles) is equipped with a unit of the Raymond system of grinding and air separation, and pencil sawing machines. It is reported that the pencils are being successfully used in Pacific Coast ship yards.The mining of talc where no mill is owned by the operator and the consequent sale of talc in its crude massive state has not proved profitable in a number of cases recently noted. Under exceptional circumstances, where mining costs are low and the product can be sold to a mill near the mine, the operation maybe profitable, but this condition is not common. One mine of this type has recently closed down, at least temporarily; but a second, more fortunately situated, in another district, is continuing operations, although plans are being made to erect a mill in the early spring. Most satisfactory results are ordi¬narily obtained where the mine and mill are owned by the same company.The sale of the Balmat mine of the International Pulp Company, near Gouverneur, N. Y., to J. H. McLear, Gouverneur, and H. G. McLear of New York, has been reported. It is stated that a large part of the property has been already leased to the Sylvia Lake Company, who will operate it. ""Cement, Hill, and Quarry""* states that ""the first mining done on this property was for silver and lead, but it developed into a good zinc producing property and later it was worked for its talc deposits. It has passed through several hands, the American Pulp Co., the Union Talc Co., and the International Pulp Co., all having had it in successive periods since 1891."""

Jan 1, 1920

By William H. Schiffbauer, William D. Mayercheck, August J. Kwitowski

This report summarizes work sponsored by the Bureau of Mines in the development of a remote operating system (ROS) for controllng a thin-seam continuous miner (TSCM) 500 feet or more distant from the extraction face. Detail s are provided on ROS subsystems including the continuous miner, video equipment, controls and displays, the electronic control system, and the operator station.

By Edward Thomas

"HISTORYThe origin of roof bolting as a means of roof support is obscure. During the past 23 years a method was developed by the. St. Joseph Lead Co: at its mines in southeastern Missouri, ranging from occasional use of single bolts with small bearing plates to systematic networks of bolts utilizing continuous bearing plates. Officials of this company are not certain which of its employees suggested their use. Many instances of occasional use of roof bolts have come to light during the past few years in widely separated mining districts, such as in West Virginia, Alabama, Illinois, Colorado, and Wyoming bituminous coal mines, and in Pennsylvania anthracite, Lake Superior iron, and Colorado lead-zinc mines. A few of the known installations have boon in place as long as 40 years.These installations usually were made to supplement wooden timbering in mine openings whore space was constricted, although it had been reported that roof bolting was started as a systematic moans of roof support in at least three instances but was abandoned because the cost of installation was excessive. The extra expense above that of conventional timbering could not be recaptured through economies resulting from increased efficiency, such as would be gained through mechanized mining.Roof bolting was first mentioned in mining literature in an article by W. W. Weige 3/ in Engineering and Mining Journal of May 1943, in which he described the use of bolts with 4-inch channel bearing plates in mines of the St. Joseph Load Co."

Sep 1, 1950

To reuse chromium, nickel, and molybdenum now lost in stainless and specialty steel-making wastes, and simultaneously to overcome the current environmental problem resulting from landfilling these wastes. Approach A variety of stainless and specialty steelmaking wastes are agglomerated and recharged into the plant&apos;s electric arc furnaces. How It Works Stainless and specialty steel-making wastes such as bag-house dust from the electric arc furnace, dust from the argon-oxygen decarburization unit, grinding swart, and mill scale are blended in proportion to the ratio in which they are generated. Next they are agglomerated on a pelletizer with an addition of a small amount of carbonaceous reducing agent, and air-dried in preparation for being recharged into the furnace. Some mixtures of wastes tested in the laboratory required the addition of binders and/or the use of ovens in lieu of air-drying to produce sufficient pellet strength. Although the optimal maximum particle size of wastes being pelletized is 35 mesh, somewhat larger particle sizes were satisfactorily pelletized during in-plant tests. The photograph shows a typical mixture of wastes and the pellets made from them.

Jan 1, 1981