Search Documents

Provide reasonably priced, reliable fire protection for blasthole drills. Approach An automatic fire sensing and suppression system using both dry and gaseous chemicals was developed, and is more shock and vibration resistant than similar industrial fire protection systems. How It Works Temperature sensors mounted in the drill's machinery house, hydraulic room, operator cab, and transformer area detect the heat from a fire, and trigger a sequence of actions. The same fire fighting sequence can be initiated from manual alarm boxes in the cab, hydraulic room, or machinery house. Electrical power to the drill Is immediately cut off, and a horn sounds to warn the drilling crew. After a 40-second, built-in, delay to allow time for drill's ventilating fan to stop, gaseous and dry chemical fire extinguishing agents are piped to and released in various rooms of the drill. The gaseous extinguishing agent (Halon 1301) is released in the machinery house, hydraulic room, and operator cab where dry chemical clean-up from electrical panels and machinery would be difficult and costly. Dry chemical is piped to the transformer room at the rear of the machine. Location of the principal components of the system are shown in the drawing.

Jan 1, 1979

By J. M. Stuve

The present Bureau of Mines investigation measured low-temperature heat capacities of NiBr2 (8 to 302 K) and NiS04 (9 to 70 K) by adiabatic calorimetry. The standard entropies (S°, 298.15 K) of NiBr2 and NiS04 were calculated as 29.26 ± 0.06 cal/deg mole and 24.21 0.04 cal/deg mole, respectively. (1 cal = 4.1840 joules.) Heat-of-solution measurements of anhydrous NiBr2 were used to determine its enthalpy of formation (?Hf°, 298.15 K) as -50.64 ± 0.31 kcal/mole. High-temperature enthalpies of NiBr2 and NiS04 were measured by drop calorimetry to 1,150 K and 1,002 K, respectively. Enthalpies, heat capacities, and related formation functions are tabulated to 1,200 K.

Jan 1, 1978

Minimize airborne respirable quartz dust produced by continous mining machines. Approach Install a shovel-mounted underboom water spray system on the off-curtain side of the mining machine. Dusty air containing quartz is momentarily trapped under the boom, where it is captured by fine spray mist. The remaining dust cloud is directed immediately behind the curtain before it can migrate back to the machine operator's location. How It Works Previous studies have shown that most of the dust generated by continous mining machines occurs under the boon as the cutter head shears down. The primary source of respirable quartz dust on many continous mining operations is cutting or trimming roof rock immediately prior to shearing. This results in very high concentration , of

Jan 1, 1989

By Doris M. Hyde

New mineral activity focused on increased petroleum exploration activities, while the established construction-oriented minerals sector operated without substantial change from previous years. After showing a 1 % real growth in the $154 million II gross domestic product (GDP) for 1983, preliminary estimates for 1984 indicated that the same growth pattern prevailed. The negative trade balance at midyear had worsened over the negative balance for the same period in 1983. An upward trend in import costs partly reflected the impact of Mexican inflation, which made that country's goods more ex-pensive and led to increased imports from North America and Europe. On the other hand, by midyear, the reexport trade with Mexico indicated an upward climb from the 1988 low of $12.7 million.

Jan 1, 1986

By W. Blake, J. K. Whyatt, T. J. Williams

Researchers at the U.S. Bureau of Mines collected and analyzed over core measurements and other indicators of in situ stress characteristics at the Lucky Friday Mine, Mullan, ID. An analysis of these data revealed that significant local variations in in situ stress are present in this mine and that these variations existed prior to mining. High stresses were found to be associated with the most competent strata and a locked section of a fault. An estimate of the predominant stress field was developed for mine-wide modeling. The estimate shows that the greatest principal stress was oriented north of northwest. This information should provide a basis for mine-wide structural modeling of the Lucky Friday Mine and should generate important insights into localized stress conditions, which may significantly affect both local and mine-to-mine variations in seismicity induced by excavation.

Jan 1, 1995

By Fred N. Kissell, J. E. Matta, J. C. LaScola

The Bureau of Mines made laboratory absorption measurements on oil shale samples, which showed that the amount of methane absorbed is proportional to pressure and oil yield, and can be much larger than would be predicted based solely on porosity. Oil shale cores collected in the field were also measured for their gas content using the Bureau of Mines direct method, Cores taken from deep locations and far from outcrops yielded more gas than cores from shallower locations or at outcrops, when taking into account variations in oil yield, and all data indicate that oil shale mines that are both deep and far from an out- crop will emit low levels of methane gas.

Jan 1, 1977

By I. L. Nichols

Laboratory characterization studies have investigated the processing variability of carbonaceous uranium-bearing materials found in-sandstone deposits. This work was conducted by the Federal Bureau of Mines in support of its goal to maintain an adequate supply of minerals to meet national economic and strategic needs. Conventional processing produces only partial uranium recovery from these ore materials. Ore samples from New Mexico, Texas, and Wyoming were examined, and each responded differently. Using direct acid leaching techniques, some of the ores required acid additions of only 50 pounds per ton, while others required 300 pounds per ton of material. Maximum extractions ranged from 83 to 94 percent in the six ores tested. Roasting those ores prior to leaching improved extraction of the uranium to the 90 to 99 percent range. An oxidative autoclave treatment used with five of these ores resulted in extraction of 78 to 97 percent of the uranium. The experimental studies also showed that some carbonaceous materials can be concentrated by froth flotation. The flotation tailings were amenable to acid leaching, and up to 98 percent of the uranium was extracted from this type of material.

Jan 1, 1979

By ALICE V. Petar

Like many gem materials, amber has a colorful history which may be traced through the writings of the ancients and the ornamental relics discovered from time to time. Like few gem materials, however, it is distinctly useful in products whose value has no connection with the gem industry. Long prized for its beauty, amber was fashioned into articles of jewelry and ornaments to please the fancy of ancient rulers and to find a place among treasured pos- sessions in their tombs; it has been used by adherents of various creeds for rosaries and other religious symbols; and although still sold for these pur- poses it also lends itself to such commercial purposes as raw material for varnish. Amber is only on the border-line of the mineral kingdom; actually it is of vegetable origin, having been formed as resin from trees of the conifer family that existed during the Tertiary period. It is the hardest of the fos- sil gums. The United States produces no amber, although a few occurrences are known. Most of the world's supply comes from East Prussia, where it is ob- tained from both land and sea. For many years pieces of amber were gathered from the Baltic by fishermen and deep-sea divers; and although about 10 per- cent of the Prussian amber is still recovered from the sea, most of the out- put is mined from open pits on the Samland Peninsula.

Jun 1, 1934

By Clarence O. Babcock

ROCK BEHAVIOR has proved of national interest in a variety of fields. The behavior of rock consequent to a nuclear blast was used to detect such blasts, as criteria for the design of underground military defense installations that would resist nuclear blasts, and for judging the feasibility for peaceful uses of nuclear explosives. An obvious peaceful application of nuclear explosives would be for large-scale rock excavation, and plans were presented during the year to improve the present Panama Canal or create a new canal by this method. These plans were based largely on earlier crater tests that demonstrated rock behavior when subjected to a buried nuclear blast. A knowledge of rock behavior under impact was used to evaluate the materials of the moon by means of the geometric configurations visible in the close-up pictures of the moon surface taken by the U.S. rocket Ranger 7. The composition of the moon must be considered in devising methods for taking samples of the surface layers or in designing underground shelters as bases for future explorations of the moon.

Jan 1, 1965

Native asphalt was produced by five companies in two States, Texas and Utah. Bituminous limestone, used primarily as a paving material for street and road repair, was produced by White Uvalde Mines and by Azrock Industries Inc., Uvalde County, TX. Gilsonite, a solidified hydrocarbon, found only in Utah and Colorado, was mined by American Gilsonite Co., a division of Chevron Resources Co. (a subsidiary of Standard Oil Co. of California), by Ziegler Chemical and Mineral Corp., and by Hydrocarbon Mining Co. (a subsidiary of Oberon Oil Inc., a Utah corporation) from properties in Uintah County, UT.

Jan 1, 1984

Minimize the effects of underground mine conveyor belt fires by developing methods to prevent automatic fire suppression system failures. The Problem Fire protection is achieved by prevention, early detection, and planned fire-fighting response. Automatic fire suppression systems are one form of planned fire-fighting response. When these systems are properly designed, installed, and maintained they can effectively control fires. Conveyor belt fires account for about 20% of underground coal mine fires. Fire protection requirements have been established for underground locations because of potential for start and spread of fire and the restricted personnel egress in a fire situation. Belt conveyor systems arc potentially dangerous because of the high fire incidence rate, high temperatures, dense smoke, toxic gases, and rapid flame-spread rate. While investigating the conveyor fire suppression problem, the Bureau identified automatic fire suppression system reliability as a potentially serious deficiency within the mining industry. Table 1 lists common failure modes fur three Fire suppression system types. This table summarizes findings of Mine Safety and Health Administration electrical inspectors responsible for inspection of belt protection automatic fire suppression systems. Batteries, contact points, control wires, and electric servocontrols are all prone to failure. Figure 1 shows rock-dust-contaminated relay contact points. This condition is dangerous because of the chance of intermittent failures, which might allow systems to pass annual functional testing, yet fail during actual fire emergencies.

Jan 1, 1989

Control respirable dust in underground coal mines through selection of optimum water spray pressures. Approach Through underground trials at longwall and continuous mining operations, the relationship between operating water spray pressure and respirable dust levels at the machine operator's location was determined. Defining the Application Water sprays are used for two significantly different control applications. On longwall mining machines, sprays are commonly installed both on the body of the machine and on the cutting drum. Sprays on the body of the machine are used to redirect dust which has already become airborne away from the machine operator. Each spray acts as a small fan, directing the primary airflow over and around the machine and towards the face, away from the operator. The energy of this system is directly related to the spray pressure. Higher pressures move more air, but care must be taken not to cause turbulence and boilout into the walkway. Sprays mounted on the drum are, effective at suppressing the respirable dust at the bit/coal interface and preventing it from becoming airborne. Again, these sprays must not impart excessive energy to the dust particles thus stirring up more dust than they suppress. While mounting sprays on the shearer drum is standard industry practice, there is no reliable technology available to successfully mount water sprays on the cutting drum of continuous miners. Instead, sprays are mounted on the machine body, close to the drum, and directed at the cutting head. This allows the water to reach the bit/coal interface and mix with the cut material. Here again, care must be exercised to prevent these sprays from imparting excessive energy to the dust particles and stirring up more dust than they suppress. These sprays can also cause dust "rollback" from the face, toward the operator, if operated at too high pressures.

Jan 1, 1986

At the present time many coal preparation plants handle coal-clay wastes in one of two methods. In one method, the waste is processed in a thickener, followed by further dewatering through filtration, and subsequent blending with coarse waste refuse from the preparation plant. The resulting mixture is then disposed by stacking it in available storage locations. The coal-clay waste is often reslurried by rain or water from other sources, causing a potentially unsafe situation such as mud flows. The other method often used requires thickening and impoundment of the thickened slurry behind earthen dams which poses safety risks if structural failure of the dams occurs. To overcome these two problems, a flocculation method was developed which produces a stable agglomerated material resistant to reslurrying. How It Works The new method involves treating coal-clay waste with lime to raise the pH and flocculating the slurry with a nontoxic polymer of polyethylene oxide. The resulting floes are dewatered on a static screen and agglomerated. For extremely fine waste, further dewatering of the material is accomplished on a rotary trammel screen. The dewatered material may be ponded or mixed with coarse waste from the preparation plant to produce a stable mixture that can be stacked.

Jan 1, 1985

By Robert M. Becker

A thick-wall cylinder solution applicable to the evaluation of anisotropic elastic parameters is derived for the interpretation of stress relief data. For a restricted class of problems, a special relationship among certain orthotropic moduli yields stress distributions for the plane orthotropic problem that are identical to the corresponding isotropic case. A ring or hollow cylinder with these specialized anisotropic properties subjected to uniform radial loads is one of the problems in this class. Consequently, known stress solutions are used to develop the strains and displacements for a specialized orthotropic thick-wall cylinder under uniform pressures. The results are consistent with anisotropic equations used in the evaluation of in situ rock stresses.

Jan 1, 1968

By W. M. Dressel

A simple field test for detecting the presence of germanium in rocks, coals, and flue dust has been developed by the Bureau of Mines. The method consists of dissolving germanium from the samples by either acid or fusion treatment methods, adding a few drops of hematein or phenylfluorone dye, and extracting the resulting colored complex with carbon tetrachloride. INTRODUCTION Germanium is obtained commercially as a byproduct of zinc production, as a coproduct of base-metal refining from germanium-bearing mineral, and as a recovered product from the ash of some coals. The growing use of germanium in the electronics industry has increased demand for this semiconducting metal to the extent that an intensive search for new sources of supply is necessary.

Jan 1, 1962

By Richard J. Mainiero, Michael J. Sapko, Marcia L. Harris

Since 1988, there have been 17 documented incidents in the United States and Canada in which carbon monoxide (CO) is suspected to have migrated through ground strata into occupied enclosed spaces as a result of proximate trench blasting or surface mine blasting. These incidents resulted in 39 suspected or medically verified carbon monoxide poisonings and one fatality. To better understand the factors contributing to this hazard, the National Institute for Occupational Safety and Health (NIOSH) carried out studies in a 12-foot diameter sphere to identify key factors that may enhance the levels of CO associated with the detonation of several commercial trenching explosives. The gaseous detonation products from emulsions, a watergel, and ANFO blasting agents as well as gelatin dynamite, TNT, and Pentolite boosters were measured in an argon atmosphere and compared with those for the same explosives detonated in air. Test variables included explosive formulation, wrapper, aluminum addition, oxygen balance, and density. Major contributing factors to CO production, under these laboratory test conditions, are presented. The main finding is the high CO production associated with the lack of afterburning in an oxygen poor atmosphere. Fumes measurements are compared with the manufacturer’s reported IME fume class and with the Federal Relative Toxicity Standard 30 CFR Part 15 in order to gain an understanding of the relative toxicity of some explosives used in trench blasting.

By M. C. Chapman, E. C. Westman, A. T. Iannacchione

Examination of seismic records during the time interval of the Sago Mine disaster in 2006 revealed a small amplitude signal possibly associated with an event in the mine. More needs to be understood about the seismicity from mine explosions in order to properly interpret critical seismic information. A seismic monitoring system located at NIOSH’s Lake Lynn Experimental Mine has monitored experimental gas and dust based explosions and impact tests. The seismic signatures from these different events were analyzed using standard waveform analysis procedures. The magnitude of seismic energy during a gas and dust explosion was found to be more dependent on mine entry geometry and seal behavior rather than on the amount of explosive fuel present. The results suggest a large explosion that’s not restricted can generate potentially the same magnitude as a small explosion that is restricted.

Coaxial cable structures form the subject of substantial theoretical and experimental investigations either directly related, or which can be extrapolated, to the communications needs and environments of U.S. coal mines. Communication systems based on "guided" waves, of which "leaky" coaxial cables are one implementation, are attractive candidates for providing a range of communication functions primarily along haulage ways, and possible also within sections up to the working face. (However, there are still strong reservations as to whether a practical coaxial cable sys tem could provide sufficient communications coverage within a section. ) In this Part, we present the results of some theoretical calculations of the performance of leaky coaxial cable communication systems. We also analyze the applicability of the theoretical and experimental results obtained by other researchers to the needs of U.S. coal mines. In particular, this investigation has been focused on the utility of relatively low cost, conventional, flexible, coaxial cable at frequencies covering the LF through HF bands and extending into the lower part of the VHF band, as opposed to relatively high cost, special semi-rigid, coaxial cable* at frequencies in the VHF and UHF bands. There are three major design alternatives for coaxial cable communication systems considered in this chapter: • Base station feeding a coaxial cable with high surface transfer impedance (holes in outer conductor, e.g., braid construction). • Base station feeding a coaxial cable with repeaters (U.K. experiments). • No base station, direct communication via a coaxial cable with periodic radiative structures.

Jan 1, 1974

Objective Develop field measurement and computer modeling methods to predict the potential for hang-ups and structural failures in underground mine ore paws. Background Analysis of Mine Safety and Health Administration (MSHA) accident statistics has identified ore pass hazards as a significant safety problem in underground metal mines in the United Stales. Recent ore pass failures have underlined the lack or ore pass design methods ant1 standards available to both MSHA and mine engineers. Injury and fatality data for the 20-ycar period between 1975 and 1095 show that nearly 75% of the injuries were directly or indirectly related to pulling or freeing ore pass chutes, the use of hand tools, falls or broken rock, and structural failures or chutes or gates and ore pass walls.

Feb 1, 1998

By George M. Lucich

This report describes a sensitive, proportional temperature controller developed by the Bureau of Mines that is useful in the temperature range from 40 to 400° C with an accuracy of ±0.10 C. A temperature controller of this kind is potentially useful for regulating temperatures in air chambers, liquid baths, furnaces, and reaction vessels, and for other applications. This instrument was developed to control the duration and temperature of the heating cycle of a charcoal-filled adsorber that is part of a special helium analyzer used by the Bureau. The controller was made from commercially available parts, and can be easily modified to provide continuous temperature control. The circuit is solid state and employs no electromechanical devices. Over a 2-year period of use as a component of the special helium analyzer, this temperature controller performed successfully and required no maintenance.

Jan 1, 1979