Search Documents

Etching solutions containing hexavalent chromium ions (e.g., chromic acid) are used in brass finishing, printed circuit board etching, preparation of plastic for plating, anodizing, and various other industrial surface treatment operations. As the solutions are used, hexavalent chromium ions are reduced to their trivalent state, contaminants accumulate in the solution, and the effective acid concentration is reduced. When the etching rate becomes unsatisfactory for the particular operation, the solutions are discarded. This is a problem because the discarded solutions are pollutants, and because replacing the etching solution is expensive. The Bureau of Mines has developed a process for regenerating these spent solutions and returning them to the surface treatment operation without interrupting the etching process. An electrolysis cell containing anode and cathode compartments that are separated by permeable membranes, is used for regenerating the spent solutions. The spent chromic acid solution is fed to the anode compartment and sui (uric acid is circulated in the cathode compartment. Application of a steady electrical potential of a few volts dc across the electrodes causes the copper ions and other contaminants in the spent solution to migrate through the membrane to the cathode compartment where copper is plated onto the cathode. Zinc and the other contaminants remain in the sulfuric acid. At the same time, the complex, trivalent chromium ions in the spent solution are attracted to the anode where they are oxidized to their original hexavalent state. The regenerated solution in the anode compartment is then recycled back to the plant?s etching operation for reuse.

Jan 1, 1980

Validate the premise that there is measurable seismic activity associated with abandoned mint lands and that this activity can be used to determine stability of the abandoned mine openings, failure cycle of these openings, and susceptibility of the area to surface subsidence. Approach The U.S. Bureau of Mines conducted field investigations at two geologically contrasting sites, Colorado Springs, CO, and the Allegheny Portage Railroad Historical Site near Cresson, PA, to demonstrate that developing monitoring technology can be applied to any site. An array of seven geophones (velocity-measuring sensors) were strategically located to encompass an area at each site where failure in the underground mine openings could be expected, based on historical, geological, and engineering information. How It Works Bureau research has effectively demonstrated that stress changes within a rock mass can stimulate the development of cracks and fractures, resulting in the release of strain energy that generates seismic waves. These seismic waves, traveling outward from their source, can be detected, and the point of origin can be located in three-dimensional space. Furthermore, these seismic signals contain information that defines the source mechanism and the conditions between the source and the receiving sensor.

Jan 1, 1992

By H. Carroll

An ozone detector was built and evaluated for its applicability in smog-chamber studies. The detection method is based on the reaction of ozone with ethylene and the measurement of resultant chemiluminescence. In the first phase of evaluation, the detector's response to ozone was studied as a function of several instrument parameters, and optimum conditions were defined for the maximum and most stable responses to ozone. In subsequent evaluations, the method was checked for sensitivity, precision, and interferences and was compared with two alternative methods. Results showed the chemiluminescence method to be acceptably sensitive and precise for smog-chamber studies and superior to the Mast ozone meter and KI (colorimetric 1 percent neutral-potassium iodide method) methods in that it is specific for ozone.

Jan 1, 1972

By Charles Vaught

This is the second in a series of four articles that discuss underground firefighting preparedness. As with the first article in the May-June issue, it is based on interviews with 214 miners conducted at 7 underground mines (?A? through ?G?) by researchers of the National Institute for Occupational Safety and Health?s (NIOSH) Pittsburgh Research Center [Vaught et al. 1996].In the first article, the authors presented an overview of the study conducted by NIOSH on mine fire response preparedness and provided a general perspective on underground mine fires. In this article, we will describe miners? preparedness to evacuate a fire and their experience with incipient fires

Jul 1, 1997

Minimize failures or inefficiency in the operation of in situ mining wells. Approach The proper design, construction and development of wells are important to any in situ leaching operation. To permit cost-effective production from an underground ore body by leaching it in place, many wells are normally installed. Construction and maintenance costs increase with the number of wells, and poor construction and maintenance procedures result in production losses and negative environmental impacts, To minimize these losses and impacts, the Bureau of Mines conducted an investigation to determine the optimum in situ well construction and operating procedures for the minerals industry. Factors considered during the investigation included drilling equipment and procedures; types of well casing and grouting; completion methods, e.g, screening or perforation; and system maintenance. The data collected were used to prepare a manual that offers guidelines

Jan 1, 1984

By Paul T. Allsman

THIS CHAPTER reviews the highlights of developments in mining technology during 1956 and presents a special report on the design of mine openings in stable ground. This special report is presented each year in an endeavor to stimulate use of the scientific approach to the solution of problems related to mining technology. Assuming that the literature on mining technology reflects trends in mining, it appears that two areas of activity were given most attention in 1956. One was research on mining technology,4 and the other was improvement of transportation, particularly trackless transportation, both at surface and underground mines.

Jan 1, 1958

This Part describes a mine pager phone to public telephone interconnect sys tem that permits mine paging telephones to be selectively interconnected with the public telephone system, as illustrated by Figure 1. This interconnect concept was first conceived and demonstrated in breadboard form by H. E. Parkinson of Industrial Hazards and Communications, PMSRC, as one means for providing improved emergency and off-hours communications. The third-generation prototype unit described in this Part was designed and fabricated by Arthur D. Little, Inc. This unit is a small desk-top or wall-mounted unit that connects directly to both the public telephone line and the mine pager phone line, and requires no modifications to either the public dial telephone or mine pager phones. As part of this task, ADL also built, under a very compressed time schedule, a second-generation prototype unit suitable for reliable demonstration of the interconnect concept during the Bureau's technology transfer seminar on mine communications in March 1973. * A major objective of the design of the third-generation unit described in this Part was that it be compatible with present mine pager phone systems utilizing DC voltage on the mine phone line to activate the phone loudspeakers. Therefore, this unit was designed to operate in a push- to-talk, push-to-listen mode that accommodates the inherent design differences and operation modes of the mine phones of different manufacturers. Though this push- to- talk, push- to-listen mode of operation may seem slightly unusual at first sight, we have found it is easily learned by new users. However, mine phone manufacturers wishing to expand their product lines with such an interconnect system will probably find it to their advantage to customize the design of this system to their particular mine phones, thereby utilizing the unique attributes offered by their individual product lines. This customization should not be difficult, and Section III below suggests some of the features that can be easily added to future designs. Detailed parts lists and circuit schematics for the present third-generation proto- type system can be obtained from the system manual submitted to PMSRC and placed on public file.

Jan 1, 1974

Lower the respirable dust exposure of longwall shearer operators with improved water spray systems on the shearer. Approach Orient sprays (rather than relocate them) so that dust is held against the face. How It Works Research by the Bureau has indicated that shearer operator dust levels depend largely on how fast dust from the upwind drum spreads into the walkway. Water sprays on the shearer body can greatly affect the spreading of this dust because each spray moves air like a small fan, generating strong cross-currents of air around the shearer. Poorly designed spray systems, especially those with nozzles pointing upwind, will stir up much more dust than they sup-press. On the other hand, Improved systems may be designed to hold the dust cloud against the face while also suppressing It. In such arrangements the water is sprayed downwind and used with screens made from conveyor belting.

Jan 1, 1981

Reduce the costs associated with conventional treatment of acid mine water. Approach Conventional treatment of acid mine drainage consists of plants requiring large mixing and aeration tanks, mechanical aerators and large, shallow settling ponds. Such plants are usually very costly to construct, maintain and operate. The Bureau of Mines has developed a simple, low-maintenance, highly efficient system to treat acid mine drainage which mixes, aerates, and neutralizes mine water Simultaneously in the existing discharge pipeline by using the pressure generated by the deep mine discharge pumps. The mixing and aeration action of the in-line system significantly increases oxidation rates of ferrous iron. Iron and manganese are removed, even at near neutral pH levels, due to the high efficiency of this system. How It Works The In-line Aeration and Treatment System (ILS) consists of two commercially available components, a jet pump (ejector) and a static mixer. The jet pump is simply a nozzle that converts water, already under pressure, into a high-velocity stream that entrains air by Venturi action. If neutralization is required, sodium hydroxide or lime is added along with the air at the Venturi opening. The aerated and neutralized water then enters the static mixer, which is a length of internally spiralled pipe that mixes air and water together. The two components, which are both about 8 feet in length, replace the last section of discharge pipe at a point before the mine water is emptied into a pond. Along with the settling pond, these components treat the water so that it meets discharge criteria. The system has been used at surface drainage treatment facilities as well, but in such use a pump is required to provide the necessary pressure drop across the Venturi opening.

Jan 1, 1985

By William R. Wayment, David E. Nicholson

A modified percolation - rate test is proposed for use in determining flow rates through hydraulic backfill ; in contrast to the conventional test , a percolation- rate versus void - ratio relationship is established . requirements and a detailed test procedure are described . Equipment Results of a conventional test are compared with those of the proposed modified test . The proposed modified test method yields more accurate , realistic , and usable percolation- rate ( permeability ) data . The significance of obtaining accurate percolation rates for use in analyzing waterflow through hydraulic backfill is discussed .

Jan 1, 1964

By Stuart R. Zimmerley, John Gross

"In the study of ball-mill grinding at the Intermountain Experiment Station of the United States Bureau of Mines at Salt Lake City, Utah, it was desirable to measure the work input to a ball mill at the mill itself so that consideration of motor efficiency and transmission losses would be eliminated.The device adopted is essentially that used by Prof. H. E. T. Haultain4 in measuring work input to rolls. The mechanism was changed only so as to adapt it to a ball mill.Figure 1 is a diagrammatic sketch of the apparatus.The pulley which rotates the mill is loose on the mill shaft and is equipped with ball bearings. This pulley is connected by means of three tangential springs to the driving plate, which is solid on the mill shaft. Power applied to the loose pulley is transmitted to the driving plate, and hence to the mill, by the three springs; the greater the resistance of the mill, the greater the spring extension. The extension of the springs is transmitted by the steel extension tape to the differential integrating meter.The integrating meter is operated by two friction wheels in contact with the integrator disk which revolves at a definite ratio of speed to that of the mill. The friction wheels are held in contact with the disk by the spring suspension of the integrator and are connected to a differential gear cage, the revolutions of which are recorded on a counter such as is used in gas meters. Due to the differential gears the c e is stationary when the two friction wheels revolve at the same speed in opposite directions; this condition exists when the integrator is centered on the disk and corresponds to no load or to a zero spring extension. As the lead is applied, the springs extend and move the integrator from the center or zero point, resulting in a difference of speed between the two friction wheels. Due to the revolution of the differential cage this change in. speed is transmitted to the counter. The integrator and extension tape system is kept taut by means of a light spring attached to the integrator, the spring having just enough tension to assure that the integrator returns to zero when the load becomes zero."

Feb 1, 1931

By F. P. Haver

The Federal Bureau of Mines investigated aqueous electrolysis as a means for reducing lead chloride prepared by ferric chloride leaching of galena concentrate: NaC1 PbS + 2FeC13 ? PbC12 + 2FeC12 + S°. During electrolysis, metal was produced from solid lead chloride in contact with the cathode rather than from lead in solution. Relatively high current densities--up to 300 amp/ft2--were possible when operating in this way. A very simple cell, having a horizontal lead cathode at the bottom and a vertical graphite anode at the top, was employed. Lead chloride crystals, covering the cathode, were converted to metal powder during electrolysis, and chlorine gas or FeCls was produced at the anode, depending on the electrolyte composition. Electrolytes tried included aqueous solutions of HCI, NaCl, NH4Cl, and FeC12-NaC1. Optimum results (96-pct current efficiency, 0.23 kwhr/lb Pb) were obtained with 20 pct HC1 at 25° C, using a current density of 15 amp/ft2 and an electrode spacing of 1 inch. When the current density was increased, the energy requirement increased also but only to 0.41 kwhr/lb at 150 amp/fr3 and 0.58 kwhr/lb at 300 amp/ft2.

Jan 1, 1978

By E. K. Stanek, P. Kantabutra, R. A. Wolf

This paper summarizes the cause and effect of induced voltages in multiple conductor cables supplying alternating current power to equipment in under- ground coal mines. The investigation of this phenomenon revealed that the electrical energy produced by the resultant electric arcing between the frames of mobile electric face equipment was of a sufficient magnitude to ignite explosive methane-air mixtures. The results of laboratory tests and field tests made between equipment frames during actual operation in numerous coal mines are discussed. Several methods of eliminating or suppressing the induced voltages to nonincendive levels are also described. It is the purpose of this paper to convey to the mining industry a knowledge of this problem and to recommend methods of eliminating or reducing these induced voltages or arcing currents to safe levels.

Jan 1, 1975

By R. F. Abernethy

The work discussed in this report was done by the Bureau of Mines to develop a method for determining trace amounts of fluorine in coal. Samples of coal mixed with calcium oxide as a fixative agent for fluorine were ashed at 600° C and the residue was fused with sodium carbonate. The melt was dissolved in phosphoric and sulfuric acids and distilled to separate the fluorine) which was determined in the distillate by a SPADNS-zirconium spectrophotometric method. Fluorine determinations of 83 commercial coals ranged from 0,001 to 0.019 percent.

Jan 1, 1967

By H. K. Sacks

The Bureau of Mines has improved a mine dust incombustibles analyzer originally developed at the Bartlesville Energy Research Center (BERC). This analyzer provides quick, accurate analysis of the percentage of incombustible material present in dust samples taken from mine ribs, roof, and floor so that costly overdusting may be eliminated while still maintaining a proper level of incombustibles. The changes being effected on the present design of the BERC model IV rock dust analyzer should simplify its operation and calibration procedures, resulting in increased accuracy.

Jan 1, 1976

By R. T. Johansen, R. J. Heemstra

In water flooding the gradual accumulation of insoluble materials on the sand face causes the injection pressures to increase while decreasing the amount of water injected . This plugging material often is composed primarily of insoluble precipitates of calcium , iron , and magnesium . Treatment with sodium tripolyphosphate ( STP ) either eliminates or reduces the formation of precipitates . Field tests are discussed showing the almost immediate effects of using STP in the injection water . Methods of treatment , solubility of STP in fresh water and brines , and precautions to observe when starting to treat a waterflood with this chemical are given . Laboratory data show that the preferential wettability of a crude oil for reservoir rock can be reversed by adding a small amount of STP to the flooding water . This reversal in wetting tendency should not only decrease the injection pressures but also increase oil recovery by improving the sweep efficiency of a water flood .

Jan 1, 1964

By Richard A. Winters

In 1987, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied the 334-acre Mountain Lakes Wilderness Study Area (OR-011-001) in order to evaluate its identified mineral resources. The study area is located in Klamath County about 15 miles northwest of Klamath Falls, Oregon, and is adjacent to the Mountain Lakes Wilderness. The area is underlain by Pliocene-age basaltic andesite. No mining districts are in the study area nor were any claims recorded or found. There are no oil and gas lease applications. There are no identified mineral resources in the study area. INTRODUCTION This report describes the USBM (U.S. Bureau of Mines) portion of a cooperative study with the USGS (U.S. Geological Survey) to evaluate mineral resources and potential of the Mountain Lakes WSA (Wilderness Study Area), at the request of the BLM (U.S. Bureau of Land Management). The USBM examines individual mines, prospects, claims, and mineralized zones, and evaluates identified mineral and energy resources. The USGS evaluates potential for undiscovered resources based on areal geological, geochemical, and geophysical surveys. Results of the investigations will be used to help determine the suitability of the WSA for inclusion into the National Wilderness Preservation System. Although the immediate goal of this and other USBM mineral surveys is to provide data for the President, Congress, government agencies, and the public for land-use decisions, the long-term objective is to ensure the Nation has an adequate and dependable supply of minerals at reasonable cost.

Jan 1, 1988

By E. D. Gardener, Byron O. Pichard

"Methane, frequently called fire damp or marsh gas, is very well known to coal miners but to thy average gold miner it means nothing, as it is not associated generally with the rock formations in which gold is found.We have recently been conducting a study of mine air in typical gold mines on the Pacific Coast, and out of five California mines in which the air was sampled, three showed methane. Each of these three mines, referred to below as mines A, B, and C, have had accumulations great enough to be ignited. An authentic report from another California, gold mine, which has not yet been sampled, states that recently the superintendent was seriously burned by the ignition of a pocket of gas. This mine is later mentioned as mine D.Mine A is an old mine which had been abandoned for several years and permitted to fill with water. It has been unwaterad recently, and is now being developed at greater depths. During the unwatering, gas bubbles formed on the water and upon being ignited burned freely. It is reported that two men were seriously burned from accidentally igniting the gas. Samples of the bubbles on analysis showed high percentages of methane. Since the mine has been unwatered, no trouble has been experienced through gas being ignited. However, out of a total of six air samples which we took recently in scattered working places, all showed small amounts of methane, the methane content being 0.06, 0.04, 0.05, 0.04, 0.04 and 0.07 per cent, respectively. When these samples were taken methane was not suspected, but its general presence in the mine air indicates that it is being given off constantly."

Dec 1, 1921

By George S. Rice, Li C. Ilsley.

A remarkable explosion of fire-damp caused by a discharge of lightning at the new shaft at the Sitalpur coal mine, has been reported by the Chief Inspector of Mines of India, who gave the following details: "The explosion occurred during a thunderstorm, and the evidence showed that a flash of lightning had, to all .appaarances, passed down the shaft causing disruptive disohalges at certain points between the guides and the winding rope, Tending the latter at two places situated respectively 228 feet and 278 feet frem the surface, The distance between the winding rope and the side of the shaft was 6 feet 4 inohes, indicating a spark gap;of this width, and an intensity of discharge which could not fail to ignite the explosive mixture of gas and air known to be present in the shaft."

Feb 1, 1920

By George A. Morgan

Mineral production was confined to out-put of cement and gravel. However, exploration was being conducted by the U.S.S.R. and the United Nations Development Program. Development of a domestic limestone deposit and crude oil from an offshore oilfield was underway. Benin's currency remained fixed to the French franc. The gross domestic product (GDP) was $977 million in 1981, the latest year for which information was available. 2 COMMODITY REVIEW Cement.-Construction of a cement plant with 500,000 tons per year capacity neared completion at Pobé. The operator of the plant, using locally produced limestone, was the Societe des Ciments d'Onigbolo, a joint venture between Benin and Nigeria. Nigeria was expected to utilize most of the cement produced. Equipment for the plant included a 1,600-ton-per-day, oil-fired pre-heater.

Jan 1, 1984