Search Documents

By Quintin A. Aune

This report presents the results of a field and laboratory study by the Federal Bureau of Mines, in cooperation with the California Division of Mines, of the swelling-type bentonite deposits in the Vallecitos area in San Benito County, Calif. The purpose of the study was to learn if these large deposits contain bentonite of sufficient quality and quantity to be of economic value as an oil-well drilling mud additive. Large amounts of bentonitic clays are used by the petroleum industry as well as the steel industry in California. Additional amounts may be required in the near future as a concrete or earth-fill admixture in constructing dams and canals in the California Central Valley. Depletion of some local clay deposits and loss of others to military installation areas have given new emphasis to the need for developing new bentonite deposits in California.

Jan 1, 1959

By Ludwig Schmidt

[The use of vapor-tight tanks has proved so effective in reducing the evaporation losses of petroleum that today practically all operators are using this typo of equipment. It has boon shown, however, that vapor-tight tanks should be supplemented with additional measures which will further reduce evaporation. Probably the most effective use of the supplemental measures are found on the small producing leases where the breathing losses from vapor-tight stock tanks materially affect the volume and gravity of the stored oil. The breathing loss from a vapor-tight stock tank that is filled and emptied daily is a negligible quantity. Also, the filling loss, which on the average varies between 0.1 and 0.2 per cent, usually is not of a sufficient quantity to affect materially the value of the crude. However, the combined breathing and filling losses from a vapor-tight tank requiring several days to fill are of sufficient importance to warrant the use of measures in addition to the vapor-tight tanks. The breathing losses are caused by atmospheric variations. Probably the greatest are the changes in atmospheric temperature which cause changes in temperature of the vapors in the tank. During the day, as the temperature increases, the gasoline-saturated vapors in the tank expand and are forced out into the atmosphere. At night the vapors are cooled and contract, drawing into the tank fresh air, which becomes saturated with gasoline vapor and is forced out of the tank during the following day. In Addition to the maximum and minimums temperature variations there are many smaller variations throughout a twenty-four period caused by showers, clouds, winds, and other atmospheric conditions which likewise cause the tank to breathe. The two mist common measures used by lease operators for reducing breathing losses in vapor-tight tanks are, first, operating; lease tanks under pressure, and second, the use of light colored paints anti tank houses. In this report these two methods are discussed together with their adaptability to lease operation. Results of experimental observations are given which show the reduction of evaporation looses where these supplemental measures have been used.]

Jan 1, 1927

By Jacqueline A. McClaskey

The U.S. Bureau of Mines Information and Analysis Directorate collects world-wide data on virtually every commercially important nonfuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U.S. economy. The Bureau's data collection activity was instituted by the 47th Congress in an appropriations act of August 7, 1882 (22 Stat. 329), which placed the collection of mineral statistics on an annual basis. The most recent authority for the U.S. Bureau of Mines survey activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (Public Law 96-479, 96th Congress). This act strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral-material production or consumption.

Jan 1, 1992

By Ernest F. Burchard, J. R. Thoenen

"INTRODUCTION Technically speaking, bauxite is not a definite mineral but a mixture of several minerals belonging to a group of partly consolidated material known as laterite, which have been formed by surface weathering of rocks.The term bauxite is applied to the ore of aluminum, although a substantial amount is used for other purposes, such as a base in certain chemical industries and in the manufacture of artificial abrasives, refractories, and certain cements. Although bauxite has not been classed as strategic it now appears that the domestic supply may be insufficient for expanded defense requirements.Until recently, domestic production of metallic aluminum has been ample to meet requirements, but estimates of pyramiding future needs of the defense program have caused serious attention to be directed to the self-sufficiency of this country, both as to the supply of the raw material, bauxite, and the metallurgical capacity available to convert the ore to metallic aluminum.At the request of the Secretary of the interior, representatives of the Bureau of Mines and the Geological Survey recently investigated domestic resources of bauxite.A preliminary study of published literature and a field investigation disclosed that"

Nov 1, 1941

By T. S. Chen

A study was made by the Bureau of Mines of the temperature and thermal stress distributions in thin circular disks subjected to peripheral thermal shock at various rates of heat transfer. The theoretical analysis is based on one-dimensional radial heat flow by conduction in the disk, and on heat exchange by convection between the disk and its surroundings. Preliminary experimental data obtained from shock tests on thin circular disks of basalt, quartzite, and taconite show reasonably good agreement with theory. The case of constant properties and plane stress is treated. Solutions of the stress distribution are presented for both cooling and heating shocks. The elastic energy stored at fracture is examined, and on this basis an average stress theory is formulated. Physical properties vital to the studies include thermal conductivity, thermal diffusivity, tensile strength, Young's modulus, and linear coefficient of thermal expansion. This work is of importance in predicting the thermal shock responses of a rock body of finite size.

Jan 1, 1966

By Robert S. Sanford

In April 1948, the Bureau of Mines was requested to evaluate the graphite deposit' known as the Benjamin Franklin and Just mines in Chester County, Pa. After preliminary investigation, it was recommended that the Bureau core-drill, trench, and sample the deposit and make beneficiation tests on the ore. During the first and second World Wars, flake graphite was in short supply, and a number of deposits in the United States were exploited. In 1942, the Defense Plant Corporation, through its lessee, the Benjamin Franklin Graphite Co., purchased 70.263 acres of graphite-bearing land and built a complete mining and milling plant with a capacity of 300 tons of crude ore per 24-hour day at a cost of $426,250 (Plancor No. 1254).

Jan 1, 1949

By Katherine Harding

Basic concepts of matrix algebra and manipulations of matrices are presented in such a way that little competence in mathematics is required. Examples are always included to illustrate concepts and techniques. The paper is divided into six sections. The first four sections are devoted to some of the more basic concepts of matrix algebra, whereas the last two sections are concerned with specific applications.

Jan 1, 1967

By H. D. Baylor

This is the first of a series of papers describing mining methods and costs at cement plant quarries throughout the United States and deals directly with those methods employed and costs obtained at the quarry of the Louisville Cement Co. located at Speed, Ind. ACKNOWLEDGMENTS The author wishes to acknowledge the assistance of Mr. J. M. Buohheit, superintendent of quarries, and Mr. H. E. Schoonover, quarry engineer, in furnishing data and in compiling this report.

Jan 1, 1930

By Gary L. Hundley

As part of the U.S. Bureau of Mines program to reduce the Nation's reliance on foreign supplies for critical metals, a procedure was devised to separate and recover critical metals from mixed and contaminated super alloy scrap. The process uses both pyrometallurgical and hydrometallurgical methods to treat the scrap. The mixed scrap is converted to a matte containing 4 to 7 pct S by adding S directly to the molten metal. This matte is then granulated and ground to a minus 35-mesh particle size and leached with an HCI-CI2 solution. This process takes essentially all the Ni, Co, Cr, Fe, AI, and Mo into solution in a 3-h leach, leaving W, Ta, Ti, and Nb (Cb) in the residue. The Mo is recovered from the chloride leach solution by solvent extraction, and the Cr and Fe are recovered together by precipitation. The Ni and Co can be recovered individually by an existing solvent extraction-electrowinning process. The W is recovered by a caustic leach of oxidized Cl2 leach residue.

Jan 1, 2010

By P. A. Richardson

The current Bureau of Mines active list of permissible explosives includes 76 brands. Eleven are gelatinous and the rest are the granular type. The list of permissible blasting devices comprises five Cardox models.

Jan 1, 1970

By Clarence O. Babcock

This report describes the results of Bureau of Mines laboratory and preliminary field tests on a rock bolt of helical shape. The flexible construction allows the bolt to maintain a more stable load level than is possible with a straight bolt. Bolt load changes resulting from anchor slippage, blasting shock, or changes in mine geometry with mining advance are minimized. Preliminary field tests were performed at the Kaiser Steel York Canyon mine where the load changes of straight and helical bolts were measured using a vibrating-wire load gage. The field tests were performed to establish the viability of the concept of a helical bolt. The practical usefulness in terms of performance and economics remains to be shown. The change in bolt load for the flexible bolts was one-third that for the straight bolts. There were no malfunctions of the gage, and the bolts maintained a more uniform load than the straight bolts used as controls.

Jan 1, 1978

By Leland A. Yerkes

Refining aluminum from crude aluminum alloys by the subhalide reaction was investigated to develop a method of producing aluminum by means other than electrolysis of its oxide. The best materials and design for the apparatus and also optimum operating conditions, including temperature, pressure, vapor flow rate, and composition of alloy charge were studied. In the subhalide process, aluminum-trihalide vapor reacts with aluminum in the alloy under high temperature and low pressure, forming volatile aluminum monohalide which reverts to aluminum metal and aluminum trihalide on cooling. The only halide used in this investigation was aluminum trichloride. The crude aluminum-silicon alloys used as the principal raw material contained from 21.9 to 36 percent aluminum, and significant quantities of iron and titanium. These alloys were produced by direct electric smelting of clays. Graphite tubing that was heated by an induction coil proved to be satisfactory material for the laboratory reactor chamber, Enclosed in an insulated glass or quartz pipe, the reactor was used in both vertical and horizontal positions with various baffle and tray arrangements for directing the trihalide vapor both over and through the alloy. Aluminum trichloride vapor was generated in the sublimer at one end of the glass pipe, passed into the reactor where contact was made with the crude alloy, and aluminum monochloride gas was formed. When the gaseous mixture of aluminum monochloride and unreacted tri-chloride passed out of the reactor and entered the condenser, the gases were cooled to 900° C. or less, causing the monochloride to disproportionate into aluminum and aluminum trichloride vapor. The aluminum was deposited on the condenser walls while the aluminum trichloride vapor was carried out of the condenser and into the opposite end of the glass pipe where it solidified on the cooled copper coils.

Jan 1, 1961

By P. L. Sibrell

Electrorefining of Ti in nonaqueous solvents has been studied by the U.S. Bureau of mines as a method for recycling impure scrap Ti. Electrochemical behavior of Ti species was investigated using cyclic voltammetry. Research results showed that Ti metal can be dissolved in polar solvents such as dimethylformamide or dimethyl sulfoxide. However, deposition of Ti from these solvents was not successful. Several solvent systems were investigated for electrodeposition of Ti but no deposits were obtained. Reduction of Ti4+ complexes to Ti3+ proved to be straightforward, but reduction to lower oxidation states could not be confirmed. In dimethylformamide solutions, cyclic voltammetry results demonstrated the reduction of Ti to an oxidation state of less than three, but no Ti metal was identified. In dimethyl sulfoxide solutions containing LiCl, it was possible to deposit Li metal. After adding Ti salts to the solution, electrolysis quickly passivated the electrode. Deposition of Ti was also investigated in solutions of dimethoxyethane and propylene carbonate but, again, no reduction of Ti to oxidation states of less than three occurred. Therefore, the prospects for a nonaqueous electrorefining system for Ti metal do not appear promising.

Jan 1, 2010

By P. A. Wasson

Drill cores from 15 holes in the West Central Mesabi Range were studied as part of the Lake Superior iron resource investigation begun in 1957 by the Bureau of Mines. Chemical, petrographic, and metallurgical analyses were made to determine grade, mineralogy, magnetic characteristics, and response to beneficiation. Data in this report were developed to provide a better under-standing of the nature and character of low-grade iron ore occurrences, to measure potential of usable ore, and to provide a basis for comparison with bank samples previously taken in the same general area. The average iron content of 4,445 feet of core was 31.8 percent. Iron oxides present were hematite, goethite, and magnetite; the gangue minerals were chiefly quartz, iron silicate, and iron-bearing carbonates.

Jan 1, 1962

By Robert L. Lappi

Eight interburden handling concepts are developed for multiple seam area mine stripping operations in central and western United States. They are based on data gathered and analyzed during field surveys, literature reviews and visits to state regulatory agencies in five states. It is concluded that improvement of reclamation practices through selective interburden handling techniques is possible at lower operating costs than currently incurred. Specific multiple seam mining systems are discussed in this report.

Jan 1, 1980

By Joan T. May

The Federal Bureau of Mines investigated the potential for recovering aluminum from copper-dump leach liquors by use of single-contact ion-exchange technology. A strongly acidic ion-exchange resin was used to extract aluminum from a typical dump leach liquor and from synthetic leach liquors. Aluminum was stripped from resin with a HS04 or NaCl solution. Bench-scale experiments indicate that a single-contact ion exchange is technically feasible, but that the process is limited by the relatively low loading capacity of the resin and the excessive amount of stripping agent required. A further limitation is that significant amounts of magnesium and iron are loaded and stripped along with the aluminum.

Jan 1, 1976

By A. J. Barry

Two methods of testing anchorages of headed expansion-type mine roof bolts were investigated by the Federal Bureau of Mines to determine whether they are acceptable for general use. In both methods a load was applied to a tightened bolt with a hydraulic jack. A total of 80 tests, 40 using each method, was conducted in 4 test areas in 3 commercial coal mines. Electric resistance strain gages were used in all tests to indicate true bolt load as the bolt was tightened and when an additional load was applied with the hydraulic jack. The results indicate that: 1. The relationship between the true bolt load and the jack load will vary according to the test method until the two loads become equal. The bolt load-jack load relationship below this point can be determined only with strain gages. 2. The point at which the two loads become equal can be estimated by noting the load when the hardened washer becomes loose in one method, and when the bearing plate becomes loose from the roof in the other. It also can be approximated for either method of testing by noting the load when the first abrupt change in the slope of the jack load-bolt displacement curve occurs. 3. The anchorage characteristics of the test bolt can be determined from the data obtained from either method by examining the slope of the jack load-bolt displacement curve above the point at which the true bolt load is equal to the jack load.

Jan 1, 1960

By J. A. Herdlick

"INTRODUCTION The Bureau of Mines began a broad program of exploration of various proportion in the Pine Creek area of the Coeur d'Alene mining region in the fall of 1943. As a part of this project, exploring was done at theLittle Pittsburg property in 1945. The work included driving a 500-foot crosscut from the No, 6 level and drilling four diamond core drill holes to test the behavior of the Little Pittsburg vein at depth. This report presents the data obtained by the Bureau.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources, to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyses samples and performs beneficiation tests.The Bureau's exploration of the Little Pittsburg vein was one of the activities of the Albany Division of the Mining Branch, S. H. Lorain, chief. The project was started by R. M. Gammell, mining engineer, and was continued by the author and J. R. Reynolds, assistant mining engineer.The chemical analyses included in this report were made at Reno, Nov., under the direction of A.C, Rice, acting engineer in charge, Rare and Precious Metals Experiment Station, Bureau of Mines.The cooperation and assistance of the management of the Denver Development Co. is gratefully acknowledged, in particular that of C. E. Nugent, who made available much of the operational data included in this report."

Jan 1, 1947

By William O. Vanderburg

Some mines after passing through the prospecting stage and becoming sizable enterprises still adhere to the development program of the prospect, extending their workings without definite plans. In mining operations where definite structural conditions do not exist, a prearranged layout of mine development is not feasible; but where exploration and preliminary development have indicated the extent and probable limits within which the ore is expected, careful planning of development will result in a lowering of mining costs and a consequent increase is profits. A lack of definite plane for laying out mine workings is one of the contributory factors to unnecessarily high costs. Although this paper deals primarily with the influence of level spacing on mining costs, still other phases of mine development, such as the proper spacing of ore chutes and raises, can be analyzed on a cost basis in a similar manner, as shown herein. LEVEL SPACING The problem of establishing a new level or levels in order to exploit steeply dioping ore deposits and prospect the ground at depth recurs at intervals during the active life of mines. Driving levels is largely "dead work" and therefore costly. By the judicious selection of the proper level interval after balancing the opposing factors involved in the problem, a considerable saving in mining costs can be effected. Although much has been written in regard to the various methods employed in ore extraction, mining literature is still incomplete in regard to the factors-influencing level spacing at various mines. Level spacing involves procedures not lending themselves readily to description, and, moreover, it is a phase of mining operations that is apt to escape criticism, because only those in close contact with the operations are equipped with the necessary familiarity with the conditions to pass judgment.

Jan 1, 1932

By H. W. St. Clair

This study was undertaken to provide a more adequate knowledge of the chemistry of the sulfide volatilization process for recovery of tin from low-grade Bolivian ores. The investigation was partly supported by the Department of State under its program for scientific cooperation with South American republics. The results of this investigation demonstrate the conditions under which cassiterite (Sn02) may be converted to stannous sulfide by reaction with pyrite or sulfur vapor, Quantitative data are given on the rate of sulfidization and on the vapor pressure of stannous sulfide.

Jan 1, 1954