Search Documents

By Martin J. Gavin

In an earlier paper (Karrick, Lewis, C. A convenient and reliable retort for assaying oil-shales for oil yield: Bureau of Mines, Reports of Investigations, Loral No. 2229, March, 1921. Reprinted in Eng. and Min. Jour, April 30, 1921, also in Mining & Met., May, 1921) which describes the apparatus and method used in the laboratories of the Bureau of times for assaying oil-shales, no mention is made of the quality of oil obtained when the apparatus is operated under conditions determined to be most suitable for producing highest yields of oils. So many inquiries regarding the nature of the oil have been received, that it seems advisable to present a short report on the subject. Experimental work indicates that it is possible to vary the quantity and quality of the oil obtainable with the assay retort from a given shale by varying the conditions of retorting. As an example, some figures that are averages for several closely agreeing tests are shown below.

Jan 1, 1921

By L. C. George

Addition of an acid waste to an alkaline cyanide waste was investigated for five different combinations of electroplating wastes. At the optimum final pH values of the mixtures, metals and cyanides were almost quantita¬tively precipitated. No evolution of hydrogen cyanide was detected by a few additional processing steps, significant amounts of variable metals were recovered for recycling the waste-plus-Waste step is attractive because no reagents are required, metals arc concentrated, and a relatively harmless effluent that meets most water quality Standards for cyanide content is produced.

Jan 1, 1970

A complete list of permissible mining equipment, rescue apparatus and gas masks tested. Prior to Jan. 1, 1929, w s published in Bureau of mines Information Circular 60972. The present list includes practically all equipment tested and. approved by the Bureau, up to and including July 1, 1929. It covers electric air compressors, coal drills, mining machines, loading machines, conveyors, mine pumps, room hoists,, mine telephones, rock-dusting machines, switches, electric cap lamps, flame safety lamps, electric hand and trip lamps, flash lamps, methane indicators and detectors, blasting units, storage battery locomotives, tandem locomotives, power trucks, concrete mixers, self-contained oxygen breathing apparatus and gas masks. The system under which these devices were tested permits the manufacturer, after his equipment has passed certain tests prescribed by the Bureau of Mines, to mark his equipment with a seal showing hat it has been "approved" by the Bureau. These tests are designs to insure that the equipment has the minimum requirements for safety in use. The only object of the Bureau in making such tests and publishing lists of permissible equipment is to safeguard the lives of workers and to help lessen the hazards of mining.

Jan 1, 1929

By Levent Ozdemir

The results of a laboratory research program aimed at the development of a water jet assisted drag bit cutting system for coal mine applications are presented. Two types of drag bits, a conical and a plow bit, were tested in a hard sandstone rock with jet pressures of up to 20,000 psi. Jet locations investigated were in-front and behind the bit. For each jet mounting location, three jet impingement distances with respect to bit tip were tested. The closest jet impingement location to bit tip was found most effective, providing the greatest force reductions on the bit. Overall, significant bit force reductions up to 50 percent were obtained with jet assist. Also observed was a drastic reduction in airborne dust when jets were employed.

Jan 1, 1986

By J. E. Chilton

The Bureau of Mines has examined the operation of an oxygen sensor manufactured by the City University, London, England. The sensor produces a current proportional to the oxygen concentration by reacting oxygen at a nonconsumable cathode. The sensor design is unique in that the primary mode of oxygen transport to the cathode is by diffusion through a capillary, The sensor using this design has a stability of 0- to 0.02-pct reading change per day over a 4.7-month test, small temperature coefficient of 0.29-pct reading change per °C, and small pressure coefficient of 0.34-pct reading change per 1,000-ft altitude change, If this sensor were incorporated into an oxygen detector or monitor, this would be a distinct improvement in electrochemical-type oxygen analyzers and would be useful to the mining industry.

Jan 1, 1983

By W. K. Kleysteuber

This report covers the design and testing of a novel bulk materials conveying device by the Bureau of Mines. The transport concept of the device is to create a traveling wave with a steep front so that the bulk material slides and cascades down the front of the wave with some horizontal motion. Ideally, the front should act like a continuous chute. The concept of moving bulk materials along a belt without any forward movement of the belt itself was demonstrated. The conclusions reached were that the mechanism as designed could not overcome the inherent major disadvantages that would make the undulatory conveyor suitable for practical applications.

Jan 1, 1974

By W. M. Nabors

As part of a program to promote conservation and efficient utilization of petroleum resources, Bureau of Mines engineers at the Morgantown (W. Va.) Petroleum Research Laboratory are studying secondary oil-recovery projects in the Appalachian region. The increasing demand for petroleum and its products and the increasing cost of exploratory drilling tend to emphasize the importance of improving the recovery of oil from known petroleum reserves. Published reports setting forth the pertinent facts of these operations may help others to profit by the experience. This report presents the results of a study of secondary-recovery methods used in West Virginia by the Piedmont Oil and Gas Co., the Ryan Oil Co., and Water floods , Inc., on their Roane County leases in the Walton and Clover Rush Run pools. The principal oil-producing horizon underlying the area studied is the Big Injun sand, at approximately 2,000 feet. The sand is often referred to as blanket sand because it underlies much of the State and is oil-productive in many localities. Most of the pools in the area were discovered during 1907 to 1910 and were similarly developed and operated.

Jan 1, 1960

By Frank B. Fulkerson

Three of the five primary aluminum producers in the Pacific Northwest have facilities in the region to make aluminum mill products. Only one of the three, however, produces a variety of shapes and forms. The principal reason for the lag in development of an aluminum mill products industry was found to be transportation cost. The long range outlook is for expansion, based mainly on growth of the western market for aluminum used in construction, containers and packaging, electrical applications, diesel trucks, mobile homes, and irregation pipe. Consumption of western aluminum mill products in 1985 is projected at 1.1 million tons, compared with estimated consumption of 250,000 tons in 1961.

Jan 1, 1965

By R. L. Handy

The objective of this research was to devise and test an apparatus to rapidly evaluate the cohesive and frictional strength of coal in situ, in order to increase the safety and percentage of coal recovery from underground coal mines. During the first year device was designed utilizing the bore-hole shear test principle from soil shear strength testing: Two opposing corrugated plates are forced outward to exert a controlled contact pressure against the sides of a previously bared hole, and then the plates are very slowly pulled along the axis of the hole to cause shearing of coal in contact with the plates. Results with the device are expressed in terms of a friction angle[_] and a cohesion c. The [ ] angles obtained from an Iowa coal arc in close agreement with and fall between results from triaxial and direct shear laboratory tests on the same coal. The measured cohesion was found to be much less than from the comparable laboratory tests. It may be increased by pre-stressing and other techniques to embed the shear plate teeth for the first shear test point.

Jan 1, 1973

By M. M. Wong

Electrolysis of titanium carbide and a material consisting of titanium, carbon, nitrogen, and oxygen as soluble anodes in Used electrolytes was investigated by the Bureau of Mines for the preparation of crude titanium metal. Tests made in all-chloride electrolytes showed only a low recovery of titanium as well as a substantial volatilization of titanium trichloride (TiC13) when present in the electrolyte. Electrolysis at 750° to 850° C in a mixture containing 85 percent NaC1-15 percent potassium floutitanate (K2TiF6) yielded as high as 91 percent recovery of titanium from titanium carbide and 62 percent recovery of titanium from the titanium-carbon-nitrogen-oxygen material. Problems associated with the preparation of crude metal by fused-salt electrolysis are discussed. The crude metals produced from both anode materials were electrorefined in a sodium chloride-titanium chloride (NaCl-TiC12) electrolyte, and ductile titanium metal was obtained.

Jan 1, 1963

By L. Kaufman

Fifteen boride composites were synthesized by hot pressing and evaluated by physical and incendivity testing as non-sparking tool materials. The incendivity tests, conducted at the U. S. Bureau of Mines, Albany Research Center, compared the boride compo-sites with standard cobalt-bonded tungsten carbide material used for coal cutter bits. Two titanium diboride composites and two zirconium diboride composites out-performed cobalt-bonded tungsten carbide in wear resistance and reduced tendency to cause ignitions. However, three of these candidates exhibited undesirable chipping. The remaining candidate, a TiB2-(Ni, Cu) composite, did not chip, nor did it cause ignitions at levels where cobalt-bonded tungsten carbide tools caused ignitions in the incendivity tests. Thus, this material appears to be a logical candidate for further development.

Jan 1, 1973

By E. J. Matson

"SUMMARYThe Bureau of Mines has been investigating deposits of critical and essential minerals in the United States since 1939. Projects were set up on only the most promising properties. A preliminary examination of the Rio Grande property was made by Bureau of Mines engineers in July 1942 and the property was examined again in July 1943.The Geophysical Branch of the Bureau undertook a Geophysical survey of the area in November 1943 and was intermittently active in the district until June 1946. The major portion of their work was done from June 191 to November 1945. Favorable areas for exploration were recommended by the Geophysical Branch of the Geological Survey, 3/ and all holes were drilled in them.Two projects were set up by the mining branch in an endeavor to find ore bodies on the strength of the geophysical information."

Sep 1, 1947

More gold is being produced now than ever before in recorded history. All over the world huge quantities of ore are being mined and processed, thanks to historically high prices for gold and the use of processing techniques demonstrated as cost efficient in the last 20 years. Over the past 10-15 years prices for many other metals have been depressed, and gold has accounted for a significant proportion of worldwide exploration and development expenditures(l)1. The revenues generated from gold mining are providing greater return on investment, more jobs, and more tax revenues to national governments than ever before. Emerging nations are using the gold industry as a springboard for development; developed nations are continuing to fuel their economies with gold industry revenues; and China and countries of the former Soviet Union are using the gold industry to generate foreign exchange, modernize their mining industries, and take the first tentative steps toward private sector participation in their economies.

Jan 1, 1994

By A. T. Iannacchione, D. G. Puglio

The Bureau of Mines established geologic factors affecting the mining of the Lower Kittanning coalbed to aid in coalbed minability studies and examined the occurrence of "wants" (places where coal is missing) and types of unstable roof rock strata. Trends established from mapping, including prediction of areas of high methane emissions, were extrapolated to unmined areas. "Wants" in the coalbed are of two types: Erosional and depositional. Erosional features occur where north-south-trending sand-filled channels cut into the coalbed. Variations in depositional environments have caused the coalbed to "split" into several thinner units. Slickensides, commonly indicative of unstable roof, are adjacent to and on the underside of sandstone channels; they were caused by differential compaction and by soft sediment sliding along the contact between the sandstone and adjacent shale. The frequency of unstable roof also increases where the interval between the Middle and Lower Kittanning coalbed is less than 30 feet. The zones of weakness at the contacts above and below the Middle Kittanning coalbed are the controlling factors for unstable roof in these strata. Methane emissions from the coalbed are controlled primarily by depth, fracture permeability, and rank of coal. Local geologic factors are coalbed thickness, associated rock strata, structure, and proximity to outcrop.

Jan 1, 1979

By C. M. Mason

The current Bureau of Mines active list of permissible explosives includes 95 brands. Twelve are gelatinous and the rest are the more commonly used granular ammonium nitrate type. The list of permissible blasting devices comprises five Cardox models.

Jan 1, 1968

By J. E. Tiffany, Gaigler. Z. C.

"PREFACEIn presenting this list of permissible explosives and blasting devices, the Bureau of Mines desires to call attention to pages 16 and 21 outlining the conditions in use under which, and only under which, the explosive or blasting device is permissible.In view of a recent publication recounting trade practice favoring the use of a blasting device without stemming, particular emphasis is placed upon condition 4 on page 16 and condition 2 on page 21. An explosive or a blasting device enumerated in the permissible lists of this Bureau is not permissible in use unless it is properly confined with clay or other incombustible stemming.PERMISSIBLE EXPLOSIVES TESTED UNDER SCHEDULE 17CAn active list of permissible explosives was published in December 1937 as part of Bureau of Mines Report of Investigations 3361, under the title ""Active List of Permissible Explosives and Blasting Devices Approved Prior to June 30, 1937.n This list included 196 brand names.Changes in the list that have been authorized to June 30, 1938, placed 7 additional brands of permissible explosives on the active permissible list as a result of tests, changes in brand names, or transfer from the inactive list. Twelve permissible explosives were transferred from the active to the inactive list. The present list contains 191 brand names. The brand names of the permissible explosives placed on the active list are as follows:"

Oct 1, 1938

By Robert H. Bedford

As a result of the Bureau's general survey of quicksilver deposits in California, the Guadalupe mine area was among those chosen for exploration. Exploration, such as that at the Guadalupe, was aimed primarily at maintaining or increasing production of quicksilver during the critical wartime period. The project as originally planned contemplated sampling the dumps and prospecting some promising surface exposures by bulldozer trenches. Salvage was the objective in the first case and new ore in the second. Later, a program. of diamond drilling was added, designed to add both to ore reserves and to geological information. This report summarizes the history, notes the location and physical features, mentions property and ownership, and presents a brief description of the mine. The geology is outlined, and the work done by the Bureau of Mines is explained and supplemented with accompanying maps. The work involved repairing 1-1/4 miles of roads; bulldozing 13 trenches by removing 2,345 cubic yards of dumps to provide for sampling; digging and sampling 9,284 linear feet of hand trenches, digging and sampling numerous test pits; and drilling 7 diamond-drill holes, totaling 1,000 feet. A total of 419 samples, including 10 percent check samples, were taken. Exploration work in California at the time of this project was under the direction of Spangler Ricker, supervising engineer of the California field office, the late Robert Bedford was in charge of the fieldwork on this project.

Jan 1, 1950

By O. M. Bishop

"INTRODUCTION Early in World War II, the Bureau of Mines realized that reserves of fluorspar ore at many mines in the southern Illinois fluorspar district were not being developed as rapidly as the old ones were being depleted. At some mines the measured and indicated ore reserves were almost entirely depleted, although geologic factors favored new discoveries. The Leo mine, which had not been worked since 1938, was among this group of mining. The Bureau of Mines, together with the Illinois Geological Survey examined the property, studied the mine records and,geologic factors in 1944, and agreed that exploratory drilling was warranted Funds were,obtained for the work in the fiscal year 1945, and drilling was done; between October 27, 1944, and June 15, 1945.The property was owned in fee simple by the Hllside Fluor Spar Mines at the time exploration was begun in October 1944. Subsequently, in 1945, the Inland Steel Co. acquired of the Hillside property."

Jan 1, 1947

By W. I. Nelson

This paper which describes the milling practice of the Engels Copper Mining Co., is one of a series on milling methods being prepared for and published by the United States Bureau of Mines. ACKNOWLEDGMENTS Acknowledgment is made of the assistance rendered by J. Casagrande, mill foreman of the Engels concentrator, in collecting much of the data presented in this paper.

Jan 1, 1932

By John B. Gayle

A new, experimental coke oven was installed at the Southern Experiment Station, Tuscaloosa, Ala., in 1948. This oven, designated as the Tuscaloosa oven, features a 17-inch carbonizing chamber, globar heating elements, and silica-brick heating walls designed to simulate as closely as possible carbonizing conditions in commercial, slat-type coke ovens. Zoned heat-input arrangements maintain uniform temperatures over approximately 95 percent of the total flue area. The reasons for constructing an oven of this size, the details of the design, and the operating characteristics of the oven were given in an earlier publication.2/ This report presents the results obtained from the first series of carbonizing tests on Alabama coals with the new oven. Factors leading to the development of standardized operating and testing procedures and the results of crosscheck determinations with a commercial oven producing foundry coke are included also.

Jan 1, 1954