Search Documents

By Maria I. De Rosa

Table 28 and figure 10 show the number of fires and fire injuries for coal preparation plants by state during 1990-1999. Table 28 also shows the risk rates, employees' working hours, and lost workdays by state. For coal preparation plants, 91 fires occurred in 1 1 states during 1990- 1999. Twenty-three of those fires caused 25 injuries (the yearly average was 9.1 fires and 2.5 injuries). Ten fires and eight injuries involved contractors. The Ewhr value was 24 1 x 10' hr (Irr = 0.02 l), and the LWD value was 198. Pennsylvania had the most fires (24 fires and 4 injuries), whereas West Virginia (22 fires and 7 injuries) and Kentucky (22 fires and 7 injuries) had the most fire injuries. Among these states, Kentucky had the highest injury risk rate value (Irr = 0.025). Table 29, partly illustrated in figure 11, shows the number of fires, fire injuries, risk rates, employees' working hours, and lost workdays by time period. The number of fires decreased during most of the periods (an increase is seen only during the last period). The number of fire injuries show a decrease followed by an increase during the periods, accompanied by a decline in employees' working hours throughout the periods. The Irr values follow patterns similar to those shown by the injury values (see table 29 and figure 11). Tables 30-35 show the number of fires by ignition source, method of detection and suppression, equipment involved, location, and burning material by time period. Figure 12 shows the major variables during 1990-1999. Table 36 shows the fire injuries per number of fires causing injuries and total fires by year, ignition source, equipment involved, and location.

Jan 1, 2004

By S. H. Katz, J. J. Bloomfield

In studies of mine and tunnel ventilation conducted by engineers of the Bureau of Mines , various smokes are used to determine flow of air , direction of the currents , and the rate of mixing . The instrument for generating streams of sulphur trioxide (SO ) smoke , shown in the drawing herewith, has been found helpful , convenient and practicable for such purposes ; it is also especially useful in some places where fire for generating smokes is not permissible . The apparatus consists simply of a glass tube containing fuming sulphuric acid on granular pumice stone , attached to a rubber syringe bulb . When a squeeze of the bulb blows air through the tube , a stream of dense white smoke evolves, which follows and makes visible the air currents . The tubes after preparation are hermetically sealed to prevent deterioration . When ready for use , they are easily broken open at a file scratch for the purpose on both tips , and inserted into a rubber nipple at the bulb . Sometimes it is of advantage to attach them to a longer rubber tube leading to the bulb . Tubes of the size shown (about 1/2 inch outside diameter by 5 inches long) are usually sufficient for the needs of a day . Thereafter they cease to fume because the acid absorbs moisture from the air and looses its effectiveness . Smaller sizes of tubes and larger have been made , but the size shown has proved most practicable . Immediately after a person has finished using a tube it should be buried or disposed of in a place where it will not be touched by shoes or clothing, or come in contact with wooden floors , furniture , or metals , because the acid , which will eventually leak from the tubes , is highly corrosive . -- Reports of Investigations , Department of the Interior , Bureau of Mines .

Jul 1, 1923

Minimize drilling time in roof bolting. Approach The Bureau of Mines conducted a survey of 34 roof bolting machines used in underground coal mines. Results of the survey indicated that drilling time, bit cost, and respirable dust concentrations and be reduced by using the appropriate bits for drilling, To evaluate bits currently used and to find optimum cutting parameters needed to minimize drilling time, the Bureau tested two bits commonly used in most underground mines on both wet and dry systems. These are the dusthog* and shank type. The dusthog has dust ports in the bit body to remove cuttings. With shank bits, holes in the drill steel do this. Cost of each type is roughly equal. Bolters with dry vacuum systems were tested in the laboratory first. The lab tests were verified by underground tests in several mines. Bolters with low-pressure wet drilling systems were also tested under-ground. Tests concentrated on the effect of rpm, water and airflow rates, heating, wear, bit design and bit type. Lab Results -Dry Drilling Holes were drilled during the laboratory tests using a production model bolter drilling 45-inch-deep holes into mixtures of lime stone and sandstone aggregate. All tests started with new shank and dusthog type bits at 225 and 450 rpm. Thrust was about 6,000 lbs in all tests. Each bit was tested at two airflows, 15 and 25 cfm, airflows which are typical on operating roof bolter bits. Eleven styles of bits were evaluated. On the average, dusthog bits drilled 25% faster than shank types and were always cooler after drilling. The effect of RPM was tested with 5 different bit types. When bit rpm was increased from 300 to 400, drilling rates doubled. With used, well-worn bits drilling time and final bit temperature were more than doubled.

Jan 1, 1986

By P. L. Woolf, J. P. Morris, E. Foerster, G. R. Zellars

Measurements of vapor pressure can be used to determine the thermodynamic activities of the components of metallic solutions . The determination of activity by this method requires accurate values for the vapor pressure of the pure component and for its partial pressure above the alloy solution . This investigation was conducted to measure the vapor pressure of liquid manganese for use in future studies of the activity of manganese in various liquid alloys . In related investigations in the Bureau's Pyrometallurgy Laboratory , vapor pressures of copper , iron and nickel have been measured and activit 4 5 6 have been determined in the iron- copper and iron- nickel systems . Difficulties were experienced with manganese which were not encountered in the previous investigations . Manganese oxidizes readily and greater care was needed to maintain an oxygen- and moisture - free atmosphere in the furnace . In addition , liquid manganese wet the refractories and there was a tendency to foam and splash on introduction of the carrier gas . Because of these difficulties several variations in the experimental procedure were studied . These were first tested with silver which has a vapor pressure of the same order of magnitude as manganese but is relatively inert at high temperatures . Although no significant changes in the original procedure resulted from this work, considerable data were obtained for silver and have been included in this report . Bauer and BBrruunnnneerr7/ have reported the only extensive investigation of the vapor pressure of liquid manganese . However , their results are not consistent with the data obtained by McCabe and Hudson for solid manganese . Measurements of the vapor pressure of silver have been reported by McCabe and Birchenal1,2/ Schadel and Birchenall , 10/ Harteck , 11 / Fischer , 12/ and von Wartenberg.13 / Generally , these investigators conducted their measurements at lower temperatures than were used in this study .

Jul 1, 1960

By J. G. Kirby, F. S. LOTT

The mmber of petroleum refineries in the United States decreased during 1949 from 375 to 367 while the total crude-oil charging capacity of refineries continued to increase. A gain in the through-put capacity of 257,305 barrels daily raised the total to a new high level 6,696,300 as of January 1, 1950. The capacity of the average refinery to process crude-oil increased during 1949 from 17,171 barrels daily to 18,246. The four coastal refinery districts accounted for 178,900 barrels or 70 percent of the total capacity increase and the Illinois-Indiana- Kentucky district 57,950 barrels, or 23 percent. Slight declines in capacity were reported in the Texas Inland and the Arkansas-Louisiana Inland districts. The capacity building on January 1, 1950, 145,600 barrels daily, was less than half the amount under construction a year earlier. Most of the new construction involved enlargement of existing refineries and was confined to the East Coast and Indiana-Illinois-Kentucky districts. Two new refineries, however, were under construction, one in Oklahoma and the other in Texas. The shut-down capacity increased for the first time since 1946, and the 473,302 barrels daily reported on January 1, 1950, was the largest recorded since January 1, 1938. The only refining district showing a decline in the shut-down capacity was the Appalachian No. 2 district. The largest increases were reported in the Texas Gulf, Indiana-Illinois- Kentucky, California, and East Coast districts. The operating ratio of the petroleum refining industry, as indicated by dividing the January 1950 runs to stills of 5,483,000 barrels daily by the total installed capacity January 1, 1950, was 81.9 percent, compared with a ratio of 87.8 percent at the beginning of 1949.

Aug 1, 1950

By George S. Rice, L. C. IlsLey

"A remarkable explosion of fire-damp caused by a discharge of lightning at the new shaft at the Sitalpur coal mine, has been reported by the Chief Inspector of Mines of India, who gave the following details:""The explosion occurred during a thunderstorm, and the evidence showed that a flash of lightning had, to all appearances, passed down the shaft caus¬ing disruptive discharges at certain points between the guides and the winding rope, rending the latter at two places situated respectively .228 .feet and 278 feet from the surface, The distance between the winding rope and the side of the shaft was 5 feet 4 inches, indicating a spark gap ;of this width, and an intensity of discharge which could not fail to ignite the explosive mixture of gas and air known to be present in the shaft.""The Compressed Air Magazine, January 1920 issue, which contained the above extract also goes on to state;""In 1915, M, Ferey described in a paper read before the Societe de l'Industrie Minerale phenomena of a similar character to the above. In a pit liable to sudden outbursts of gas, for the sake of safety, shot firing was carried out from the surface. During a storm, in the year 1905, shots went off in two places after the detonators had been connected to the conductors) we read in the Colliery Guardian, London. These shots were situated respectively 1,400 and 1,410 metres from the firing station, Realizing the possible danger from this cause, the precaution was taken to cut the conductors at the bottom of the shaft and to connect there just before firing, Even under these conditions a shot went off spontaneously, -.owing, it is believed, to lightning."""

Feb 1, 1920

By A. L. Murray, P. A. Surgeon

The Spring Canyon Mine Rescue Association is a cooperative association supported jointly by five coal-mining companies located in Spring Canyon, Utah. The properties of mining companies the Carbon Fuel Co, Rains , Utah, the Liberty Coal Co. , Latuda, Utah, the Standard Coal Co. , Standardville , Utan, the Spring Canyon Coal Co. , Storrs , Utah, and the Peerless Coal Co. , Peerless , Utah about a mile apart and normally employ a total of 915 men , 733 underground 182 on the surface . and The Association was organized on July 5, 1921 , and Rudolph Clark, fomerly first - aid miner on U. S. Bureau of Mines Rescue Car 11 , was placed in charge. as manager . A board of directors made up of a representative from each of the cooperating companies (usually the mine superintendent ) is the governing body of the Association and the expenses are prorated on a basis of the production of each of the five mines . The Association maintains eight sets of Gibbs rescue apparatus and a motor truck fitted up as a combined rescue truck and ambulance . Additional apparatus are to be purchased . Standardville is the central camp in the canyon and has been made the headquarters of the Association . The apparatus are now kept and the truck housed in a small station, but plans have been prepared for a large station which will be built this summer . This new station will have a large apparatus room , a test chamber, a suitable room. for training, and a garage on the first floor, while above will be the living quarters of the manager . There is a good road through the canyon and the other camps are all within two and one -half miles of Standardville .

May 1, 1922

By J. W. Pall

The method of mining bituminous coal in Pennsylvania cannot be treated in an extended manner in this publication since this would require more space than justified. The general plan of operation of most mines is on the room and pillar system, using double entries from which the rooms are driven In the early mining in the Pittsburgh coal bed the "checkerboard" plan was much used, but this entailed a large loss of coal in the blocks of coal that were left standing. In recent years there has been a tendency towards the adoptions of the panel, room and pillar method, also the block system, which ad mats of concentrated mining within a relatively small section of the mine It is not unusual to use 4, 6, or 8 parallel entries for the panel development. The longwall advancing method has been tried in some of the thin beds of the central coal field, but so far it has not passed beyond the experimental stage. The average extraction' of coal throughout the State is 714 per cent, but it is estimated that 15 5 per cent of the loss is avoidable, so the actual extraction should approximate 87 per cent. Pennsylvania is exceptionally well provided with means of transportation by trunk lines, branches, and by intra State railroads, among which are the Pennsylvania, Baltimore & Ohio, New York Central, Buffalo, Rochester & Pittsburgh, Western Maryland, Bessemer & Lake Erie, Pittsburgh & West Virginia, Pittsburgh & Lake Erie, Erie, Monongahela Division, and Montour railroads, all of which reach some of the bituminous mines The Monongahela River furnishes water transportation for Allegheny, Greene, Fayette, and Washington counties During 1923 the coal traffic on this river amounted to 18,709,084 tons, and of coke, 385,426 tons Coal is moved on the Allegheny River also, the total in 1923 being 911,178 tons s.

Jan 1, 1928

By Thomas Varley

Data on the consumption of reagents used in flotation during the years 1923 and 1924, in metallurgical plants in the Unites States, are presented in this paper. Two previous reports Lave been issued by the Bureau of Mines on consumption of oils and other reagents used to flotation - namely, "Statement of Flotation Oils," by O. C. Ralston, issued in 1913, and Serial No. 2203, "Consumption of Reagents Used in Flotation," by Thomas Varley, for the year 1919, issued in January, 1921.

Jan 1, 1925

By Kathleen Kowalski-Trakofler, Edward Barrett

Problem: It is estimated that 5 to 10 arc flash explosions occur in electric equipment every day in the United States. In the mining industry the largest single injury category of electrical injuries are caused by non-contact electrical arcs. Method: This investigation progressed in two phases: (a) 836 Mine Safety and Health Administration (MSHA) reports of electric arcing incidents that occurred over a period of 11 years were reviewed, and (b) personal interviews were conducted with 32 individuals. A theoretical Safe Job Performance Model guided the study. Results: Behavioral dimensions were identified and included the effect of worker experience, judgment and decision-making ability, behavioral and organizational controls, and safety culture. Summary: The National Institute for Occupational Safety and Health (NIOSH) conducted an investigation of behavioral components associated with arc flash incidents and developed recommendations for interventions based on findings. Impact on Industry: This study fills a vacuum in electrical training with a focus on the organizational and behavioral aspects of arc flash incidents. There search is cross-cutting in its scope, in that the results apply not only to mining and construction, but many other industries employing electricians. Although the majority of mine electrical injuries are the results of burns from electrical arcs, few miners are aware that such a hazard exists. A safety training program, which includes a video and an instructor's discussion guide, was developed for electricians based on this study's findings. “Arc Flash Awareness” was released in 2007 (DHHS NIOSH PublicationNo.2007-116D) and is available through1-800 CDC-INFO. Phone:1-800232-4636 or email cdcinfo@cdc.gov. It is also available from MSHA at MSHADistribution@dol.gov or 304-256-3257 (DVD-576). Private industry is producing Portuguese and Spanish language translations.

By G. L. Barlett, J .. D. Barry

Supernatant media of dust-exposed pulmonary alveolar macrophages (PAMs) were inactive in assays for both Interleukin-1 and fibroblast growth factors (FGF). We have begun to evaluate several factors that may interfere with dust-PAM interactions. To determine the effect of sterilization on the activity of dusts, PAMs were exposed to autoclaved dust, heat-sterilized dust or to dust that had not been heated. Supernatants from the first two groups were inactive in the FGF assay, but supernatant from PAMs exposed to unheated dusts stimulated growth of lung fibroblasts. Recent data have revealed that freshly crushed mineral dusts possess labile free radicals that are absent in dust that has been stored for more than a few days. Suspensions .were prepared of a "stale" sample of anthracite dust 867 and of a freshly ground sample of the same dust. These suspensions were instilled intratracheally into guinea pigs under general anesthesia. Two, five or eight days later, PAMs were collected from the lungs by bronchoalveolar lavage, and the cells were counted. At two and five days after instillation, all lavage suspensions contained 70 to 85% PAMs, of which 5 to 18% contained phagocytized dust particles. On day eight there were again 80-84% PAMs in all suspensions, but in the presence of "fresh'" dust, 48% of PAMs. had phagocytized particles in comparison to 16% in the presence of '"stale'" dust. A similar experiment was performed in short-term cell culture. During 24 hours, >95%. of PAMs phagocytized dust particles, whether or not the dust was "stale" or '"fresh". Our studies are being extended to determine the effect of (1) removing surface oil contaminants by organic extraction and (2) suspending dusts without surfactant.

Jan 1, 1988

By D. S. Colby, E. M. SEELEY

The total production capacity of the natural-gasoline industry increased to 27,212,000 gallons (647,905 barrels) daily on January 1, 1950, from 21,322,000 gallons (507,670 barrels) daily on January 1, 1948. The rate of growth during these 2 years averaged 13 percent per year, compared with 9 percent per year from 1946 to 1948 and 6 percent from 1944 to 1946. The total number of operable plants on January 1, 1950, was 554, 5 more than at the beginning of 1948. The number of absorption plants increased by 12, the number of cycling plants by 7, and the number of combination plants by 4. The number of compression plants and charcoal plants continued to decrease. Absorption plants accounted for 67 percent of the total capacity on January 1, 1950, compared with 62 percent 2 years previous. Eighty-two per- cent of the expansion in these 2 years was in absorption-plant capacity. Cycle plants accounted for 24 percent of the total industry capacity at the beginning of 1950, compared with 27 percent on January 1, 1948. The average daily capacity of absorption plants increased from 38,400 gallons at the beginning of 1948 to 50,600 gallons at the beginning of 1950. During the same period, the average daily capacity of cycle plants decreased from 150,200 gallons to 144,100 gallons. Texas showed the largest gain in number of plants 13 absorption, 4 compression, and 4 cycling plants. The State accounted for 67 percent of the gain in capacity and on January 1, 1950 had 50 percent total national capacity. Louisiana followed with 7 additional plants. Pennsylvania reported 14 and West Virginia reported 13 fewer plants than in 1948. Most of these reductions were in the number of compression plants.

Jul 1, 1950

By Victor Kalcevic

A gas-flow retort for thermal processing of oil shale to recover shale oil was developed by the Bureau of Mines at its Oil-Shale Demonstration Plant, Rifle, Colo., from 1948 to 1952. The retort is a crossflow gas-to-broken-solids heat exchanger. The heating medium is the gas produced in the shale retorting process. The gas is heated in specially designed stoves outside the retort and recycled to the retort. Oil shale from the Mahogany ledge section of the Green River formation in northwestern Colorado was the material processed. Indicated maximum oil recoveries for 20-to 25-gallon-per-ton shale in a l2-inch-thick shale bed and a 20-inch bed are 96 and 91 weight-percent of Fischer assay, respectively. Heat requirements for maximum recovery are 600 to 750 B.t.u. per pound of shale. Properties of the recovered shale oil are affected slightly by shale-bed thickness and extent of retorting. Oil recovery from oil shales assaying over 30 gallons per ton is lower than that from leaner shales.

Jan 1, 1959

By J. A. Pile, Virgil Miller, R. G. Peterson, F. B. Petermann

"INTRODUCTION As virtually no published data are available on the sintering of fine, minus-100-mesh, ferrograde manganese ores, it is most opportune to present data on the amenability of various fine ores and mill products to the sintering process. These data cover the sintering or nodulizing of finely crushed, high-grade pyrolusite and rhodochrosite ores, sintering of manganese carbonate flotation concentrate, sintering or nodulizing the calcine from the deleading of a manganese oxide flotation concentrate, and sintering the calcines made in a Herreshoff furnace from the treatment of manganese sulfate products.If finely sized products are to be smelted in the present electric or blast ferromanganese furnaces, they must be sintered or nodulized. The only specification as to the size of the sintered or nodulized product is that it must pass a 6-inch screen and not contain over 1t-1/2 percent minus 20-mesh material. The minimum-maximum size has not been established. Undoubtedly this opti mum size will be set by the ferromanganese industry when ample quantities of manganese oxide sinters have been smelted."

Mar 1, 1942

By Victor E. Kral

"SUMMARYA preliminary examination of the Buena Vista iron deposit was made in June 1942 by Paul E. Pesonen, mining engineer of the Bureau of Mines. Subsequent examinations were made by D. W. Butner, of the Bureau, in March 1943, and by the author in July 1944, who recommended exploration by diamond drilling, trenching, and sampling. Work on the project was done during the period March 28 to May 26, 1945.Property holdings, comprising 16 claims known as the Buena Vista group, are situated in sec. 4, T. 24 N., R. 34 E., Mount Diablo base and meridian, north Churchill County, about 37 miles east of Lovelock, Nev.Three diamond-drill holes totaling 575 feet were drilled; 45 small pits and ten trenches, totaling 435 linear feet, were excavated, and 84 channel samples totaling 862 feet were obtained under supervision of the Bureau.Purpose of the project was to determine the possible downward extension of the mineralized sections exposed in the outcrops and to determine grade of the ore.Bureau work was confined to one claim only - the Iron Mountain."

Jun 1, 1947

By W. F. Netzeband

This paper, which describes mining methods and practices at the Rialto zinc-lead mine American Zinc, Lead & Smelting Co., in northeastern Oklahoma, is one of a series being prepared by the Bureau of Mines on mining methods, practices, and costs in various mining districts of the United States, The Rialto mine is in the SE1/4 SW1/4 sec. 20 and the NW1/4 sec. 29, T. 29 N., R. 23 E., Ottawa County, Okla. (fig. 1). The 200-acre property is southwest of and adjacent to the town of Picher in the central part of the Picher field of the Tri-State zinc-lead mining district (fig. 2). Other mines of the company adjoin the Rialto on the east and south. Zinc-lead ores have been mined almost continuously from the Rialto tract since 1916. The property was acquired by American Zinc, Lead & Smelting Co. late in 1951, and the mine was operated thereafter by the Nellie B Division of that company until the end of 1955, when it was subleased to the Residue Mining Co.

Jan 1, 1958

Provide reasonably priced, reliable fire protection for loading shovels. Approach An automatic fire, sensing and suppression system using both dry chemical and Halon 1301 was developed. It is more rugged than similar industrial-type fire protection systems. How It Works Temperature sensors detect heat from a fire, and trigger the system. These sensors are located inside the machinery house and under the house and shovel frame where it rotates around the crawler chassis ring gear. An alarm is sounded, and extinguishing agents are released either in the machinery house or in the ring gear area. The system can also be triggered by a manual control. If the fire Is detected in the machinery house, all power is shut down to the motor-generator sets, ventilation fan, and all electrical controls. Doors are automatically closed. After a delay to allow time for the ventilation fan to stop, Halon 1301, a gaseous fire extinguishing agent, is released inside the machinery house until it reaches a concentration of about 7 percent. This concentration is sufficient to extinguish a fire, but isn't toxic to personnel

Jan 1, 1980

By R. D. Leitch

In the course of another investigation4 during 1926 and 1927, samples of water collected from a few abandoned coal mines indicated that their drainage was usually lower in acidity than water from active mines in the same locality. In order to determine whether this condition might have a bearing on the advisability of sealing abandoned mines, a number of such mines were visited, samples of drainage were collected, and as much information as possible was obtained from officials of the mining companies and older residents of the district. The results of this work are the basis of the present report. ACKNOWLEDGMENTS The authors are indebted to E. W. Robertson, F. F. Spowart, J. H. Nagle, and W. D. Adams of the Northwest Mining & Exchange Co.; E. M. Fasset, Fred Lane, Wm. Humphreys, and Dr. T. A. Hutchison of Brockway, Pa.; C. W. Faulk of the Shawmut Mining Co.; James Hau of Kersey, Pa., and do others for information received; and to Dr, R. R. Sayers of the Bureau of Mines, under whose direction the work was conducted.

Jan 1, 1928

By John W. Frey

This paper is one of a series of digests of foreign mining legislation and court decisions prepared in advance of a general report relative to the rights of American citizens to explore for minerals and to own and operate mines in various foreign countries. This interpretation of the laws of cw Zealand, as prepared by Dr. Frey the best available information in Washington, has been slightly amplified in accordance with suggestions transmitted through the courtesy of the Department of State by W. L. Lowrie, Consul General at Wellington.

Oct 1, 1929

By William Cochran

Data on the cost and quantity available were developed for rutile (TiO2), which is potentially recoverable as a byproduct at sand-washing plants in the Southeastern States of Alabama, Georgia, North Carolina, and South Carolina. Baaed on 1969 production data, an estimated 4,300 tons of rutile could be recovered annually from plants that process more than 25,000 tons of sand per year. Rutile prices at which this resource would be available ranged upward from $262 per ton, compared with the current market value of $185 per ton.

Jan 1, 1972