Search Documents

By K. K. Kershner

Important contributions can be made to conservation of natural resources by recovering mineral values from primary and secondary metallurgical slimes and flue dusts. This applies particularly to ultrafine mineral particles that escape recovery by conventional mineral dressing. In the interest of economy and conservation the Bureau of Mines is investigating fundamental properties of ultrafine mineral values in slimes as a means of developing new or improved methods of mineral recovery. The work described in this progress report was carried on in the Bureau's laboratories at Rolla, Mo., from 1951 to 1953. The mineral material used as a subject for study was tin-ore slimes. DESCRIPTION OF TIN SLIMES The tin slimes consist principally of quartz, with appreciable quantities of tourmaline and sericite mica and small amounts of cassiterite, pyrite, hematite, and arsenopyrite. The tin content is approximately 0.5 percent.

Jan 1, 1954

By L. L. NAUS, R. D. Currie

Hazards in connection with the use of compressed-air jets for ventilating gassy mines are given little consideration by most mine officials largely because compressed air is considered the safest means of transmitting power for operating various types of mining machinery, and the inherent dangers in its use for this purpose are virtually negligible . The installation of compressed-air lines in coal mines leads to the utilization of compressed air for ventilating working places , with the result that , although the primary ventilation systems may be adequate to meet existing needs , proper conduction of normal ventilation has been neglected , so the working faces receive only a small amount ofthe total air circulated through the mine . Reliance in part on compressed air or other auxiliary means for ventilation is always attended by danger that gas will accumulate , due to intermittent operation , and the tendency is to operate auxiliary schemes only. during the working shift ( or possibly only part of the shift ) and to dispense with them during off- shifts or at times during the working shift when gas may accumulate because of lack of ventilation . When the men come on shift the auxiliary ventilating device often may be started without a preliminary examination of the working place , or .. the examination may be made sometime before the oncoming shift arrives , the gas being allowed to accumulate in the meantime. This may result in uncontrolled movement of a body of gas if proper precautions are not taken . Several mine explosions have been caused by the movement of a known body of gas by compressed air into the haulageway, where it was ignited by an arc from a passing locomotive . This danger is more pronounced where supervision is lax .

Aug 1, 1937

By James S. Browning

The Bureau of Mines conducted laboratory batch and small-scale continuous flotation tests of weathered mica pegmatite ores from Alabama and North Carolina to determine the technical feasibility of recovering commercial-grade mica concentrates. A new anionic-catonic method was developed for recovering mica in the presence of clay slimes. In continuous tests, concentrates containing 98.1 percent mica were obtained from the Alabama pegmatite ore; the North Carolina pegmatite ore concentrates contained 97.2 percent mica. The recoveries were 83.8 and 81.6 percent, respectively.

Jan 1, 1965

By J. G. Walters

In a survey of the coking properties of United States coals, the Bureau of Mines has accumulated data on more than 500 coals and blends tested by the Bureau of Mines-American Gas Association (BM-AGA) method.4/ The importance of these tests depends upon the fact that a greater number of different coals has been tested in this apparatus than in any other of similar scale, thus permitting comparison of the carbonizing properties of many coals. Evaluation of BM-AGA results with respect to industrial data supplied by member firms of the American Gas Association was one of the first objectives in developing this test apparatus and procedure. Early data showed that, de-pendent upon BM-AGA carbonizing temperature, BM-AGA and commercial results agree closely.5/ Because of limited data, statistical relationships were not established at that time.

Jan 1, 1959

By A. T. Coumbe

The Bureau of Mines has compiled pipeline mileage every 5 years since 1926, with the exception of the war period 1941 to 1949. The present survey has been made to reflect the progress under mobilization of the petroleum pipeline industry where efforts have been made by the government to stimulate construction of those facilities that would best equip the nation for a possible major emergency. This report summarizes the total mileage change 1n petroleum pipelines for 1950 through 1952. In order to increase the value of the information gathered the reporting companies were requested for the first time to report not only the net change in mileage as formerly, but also all new and used pipe laid and the total taken up. This new information permits effective appraisal of the construction effort of the industry and relates it to steel requirements.

Jan 1, 1953

By J. M. Davidson

The potassium mineral polyhalite (K2SO4.MgSO4.2CaSO4.2H2O) found in large deposits in western Texas and southeastern New Mexico is associated with varying amounts of halite (sodium, chloride, NaCl) and anhydrite (calcium sulphate, CaSO4). Although the anhydrite, because of its low solubility and slow rate of solution, is relatively inert, the halite is dissolved immediately in any process solution with which the polyhalite comes in contact. Limited quantities of sodium chloride in the liquors used for the hot extraction of polyhalite materially improve the results obtained, but only a very small sodium chloride content may be desired in the entering polyhalite in other procedures, such as Bureau of Mines process. In all of the processes suggested for the recovery-of potassium sulphate from polyhalite the control of the sodium chloride content will be desirable, if not absolutely essential to efficient operation.

Jan 1, 1934

By C. O. Hawk

Distillable oils derived from coal were desulfurized and hydrogenated at 2,500 psig in a two-step vapor-phase catalytic operation to give a product rich in saturated cyclic hydrocarbons. The first step was mainly a desulfurization at 400 C, the second a saturation at 300 C. One of the oils used as feed stock was from low-temperature carbonization of a bituminous coal, the other was from the liquid-phase hydrogenation of coal in the Bureau's pilot plant. The product from the saturation step was distilled to remove the light ends and high-boiling residue and to recover a fraction having acceptable properties with respect to heating value, density, freezing point, viscosity, and boiling range according to specifications suggested by the Air Force for ultra-high-speed aircraft fuel. Quantities of the fuel fraction available were too small for the thermal stability test approved by the Air Force. The experiments, performed on laboratory scale, comprised mostly a study of the effect of varying the oil feed rate (at constant oil-to-hydrogen ratio) on the yield of the desired fuel fraction. The yield of the fuel fraction made from low-temperature carbonization oil was a little more than 1 percent of the weight of coal carbonized; that from coal-hydrogenation oil was about 12 percent of the weight of coal hydrogenated. A few attempts to do both desulfurization and saturation in one operation with sulfur resistant catalysts, developed for vapor-phase hydrogenation or hydroforming, were unsuccessful. By leaving the low-boiling ends in both feed stocks to desulfurization, another product was obtained: a low-sulfur aromatic cut boiling below 200 C. This material would be suitable as a solvent or a chemical raw material.

Jan 1, 1965

By Henry J. Kellner, Michael J. Brnich

This U.S. Bureau of Mines report addresses issues involved in using a limited number of training apparatus to give hands-on self-contained self-rescuer (SCSR) training to a succession of miners, and provides guidance regarding methods for minimizing the spread of infectious diseases. Procedures used for preventing the spread of infectious organisms in dentistry, cardiopulmonary resuscitation (CPR) training, and scuba training are examined. The sanitizing methods of three organizations that require individuals to insert the mouthpiece as part of the SCSR donning sequence are discussed. It was found that each of these organizations was able to render their mouthpiece assemblies microbe free simply and inexpensively.

Jan 1, 1989

By Ralph B. Adair

The Bureau of Mines conducted laboratory and small-scale, continuous tests of weathered mica-pegmatite ores from Randolph County, Ala., to determine the feasibility of recovering commercial-grade mica concentrates by flotation. Two flotation methods were used in continuous tests for recovery of mica. One method utilized acid-cationic flotation for the recovery of coarse mica and alkaline-anionic-cationic flotation for recovering fine mica. This method yielded mica concentrates containing 98.6 percent mica with a recovery of 85.9 percent. The other method was based on the Bureau-developed alkaline-anionic-cationic method, and yielded concentrates containing 97.5 percent mica with a recovery of over 90 percent. In both methods, preconcentration of the ground ore on a Humphreys spiral was employed to reject over half of the feed in a product virtually free of mica.

Jan 1, 1968

By D. E. Traut

The effect of various ion concentrations on uranium absorption from a sodium carbonate solution by a strong-base, anion resin was investigated by the Bureau of Mines in support of its objective to help assure an adequate uranium supply for future needs. The studies were conducted to improve the recovery of uranium from in situ leach solutions by ion exchange. The effects of carbonate, bicarbonate, chloride, and sulfate ions were examined. Relatively low (less than 5 g/l) concentrations of chloride, sulfate, and bicarbonate were found to be detrimental to the absorption of uranium. High (greater than 10 g/l) carbonate concentrations also adversely affected the uranium absorption. In addition, the effect of initial resin form was investigated in tests of the chloride, carbonate, and bicarbonate forms; resin form was shown to have no effect on the absorption of uranium.

Jan 1, 1979

By E. J. Gleim

This report describes a trip to Europe in the interest of safety in coal mines. It reviews the Eighth International Conference of Directors of Safety in Mines Re-search, which met in Dortmund-Derne, Germany, July 5-10, 1954, to discuss results of studies made in different countries to improve health and safety conditions under-ground. It also summarizes information on subjects of special interest in the United States gained by the writer in visits to mining experiment stations in Belgium, France, and England. The efforts being made to protect life and property underground were discussed, and ideas and experiences were interchanged freely, not only during the conference but also during visits to the several countries. Helpful information was obtained on many topics of interest, but time did not permit as thorough a discussion on some of them as might be desired.

Jan 1, 1956

By Fred D. Wright

This paper describes research at the Bureau of Mines experimental oil-shale mine at Rifle, Colo., to improve blasting techniques and reduce breaking costs. Many of the conclusions are applicable to any mining operation. Experiments Were conducted on many phases of blasting. The effectiveness of various grades of explosives was compared, and several different drill-hole patterns were tried in heading rounds. An experiment was conducted to determine the maximum effective burden for various diameter blast holes. High-speed motion-picture studies were made of blasts, and the time for initial movement of rock after detonation of the explosive was measured. Experiments with millisecond-delay detonators in heading rounds proved that, when used properly, these detonators result in improved fragmentation, economical use of explosive, and compact, easily loaded muck piles.

Jan 1, 1953

By FRANCIS FEEHAN

Safety first is no longer merely a motto ; in some industries and in some parts of the mining industry it is an accomplished fact . In connection with the National Safety Competition of 1928 in which 284 mines and quarries participated , 42 plants were operated without a single lost - time accident . The winning company in the bituminous group had an accident severity rate of 0.053 per thousand man hours of exposure . Excellent safety records of various kinds are becoming more and more frequent , and the indication is that in reality safety is first in many mines and qquuaarrrriieess .. The safety achievements in the Stewart mine of W. J. Rainey , Inc. , are unusual even among mines winning awards in the competition .

Apr 1, 1930

By Charles C. Myers, Robert M. Doerr

The apparatus described was developed for determining the kinetics of gas - solid reactions at high temperatures by measuring the volume of gas consumed with respect to time . This apparatus consists essentially of a horizontal precision- bore glass tube connecting a small reaction chamber in a furnace to a large constant - temperature reservoir . A drop of mercury in the tube separates the two sides of the system and serves as an indicator that moves at a speed proportional to the rate of gas consumption . The sensitivity of the apparatus depends inversely on both the density of the gas in the system and the cross - sectional area of the tube ; with a tube having an area of 0.079 cm² , the sensitivity for oxygen at 308 ° K and 0.5 atm is 20 cm/mg . The reproducibility of data with the volumetric apparatus is good .

Jan 1, 1964

By C. P. Bowie, George L. Gates

"INTRODUCTION Experience in drilling oil and gas wells has shown that the voidance of blow-outs, twist-offs, fishing jobs, loss of circulation, and heaving and caving of shale formations into the drill hole depends largely on how well the drilling-mud fluid serves its purpose. A possible method for the control of the drilling fluids may be seen from a study of the relation between the particle-size distribution and some of the important drilling-fluid properties, such as the ability to build quickly a relatively impervious mud sheath on the wall of the hole in the porous formations penetrated by the bit during drilling operations. In a wartime economy, which urgently requires conservation of steel, proper functioning of the drilling fluid is particularly important because, as Parks 4/ has stated, intelligent use of good drilling fluids makes possible drilling of wells for thousands of feet in open holes without the necessity of setting protective strings of casing to control the movement of salt water, gas, and troublesome formations into the borehole; consequently, especially in deep wells, of proper drilling fluids materially reduces the need for casing and lowers the cost of drilling and completing the wells."

May 1, 1942

By M. O. Magnuson

As part of an experiment in the restoration of lands strip-mined for coal, revegetation studies were conducted at three backfilled strip-mine sites in north-central Pennsylvania. The sites were subdivided into plots that were given varying amounts of lime and fertilizer. In tests conducted cooperatively with State and Federal agronomy experts, the plots were then planted with a variety of trees, shrubs, and grass-legume mixtures. Initial tree and shrub survival was not appreciably affected by lime and fertilizer applications where the spoil pH was above 4.5. Of 14 species of trees and shrubs tested, Norway spruce, black locust, Japanese larch, pitch pine, and white pine were the hardiest. The ground-cover percentage of grass-legume mixtures in the second growing season was substantially increased by using lime and fertilizer. Mixtures comprised partly of fescue were the most satisfactory.

Jan 1, 1968

By Dean H. Ambrose

The U.S. Bureau of Mines recently developed computer graphics simulations to characterize mining scenarios, specifically for room-and-pillar mining operations in a three-entry longwall development section. These simulations compare productivity between shuttle car and continuous haulage systems concepts. One of the continuous haulage systems concepts has bolting capabilities that supplement haulage function. Simulations showed the continuous haulage system to be more time efficient than the shuttle car system. Researchers can reuse the simulation code (e.g., mining rates and equipment capacities can be changed) should investigators care to compare production of other mining scenarios. computer simulation, found computer model modification flaws and mining scenario conceptual errors. The fundamental rationale for three-dimensional computer is to cheaply, easily, and quickly obtain information about operation and of a current or proposed mechanical coal or metal/nonmetal mining system. This report documents the computer graphics model and simulation developments and discusses some of the results and observations from the simulations.

Jan 1, 1994

By Thomas Fraser

"INTRODUCTION The Santa River Valley of northern Peru contains extensive deposits of a good-grade anthracite that offer one of the most accessible sources of solid-fuel supply for South America. This region is served by the narrow-gage railroad of the Corporation Peruana del Santa, which taps the coal fields along the Chuquicara River and terminates at the port of Chimbote, where facilities have been provided for loading coal into ocean-going vessels.This Government-sponsored corporation is prosecuting a vigorous program of development in this region, envisaging an intensively industrialized area around Chimbot Bay, fueled and powered by the anthracite of the upper valley and a hydroelectric generating plant now being constructed in the Cahn del Fate, where the Santa River has cut through the coastal range of the Andes.This development also includes the construction of extensive irrigation works to greatly expand agricultural production in the valley and thus estab¬lish the basis for a prosperous, well-balanced, industrial and agricultural community. It is hardly necessary to point out the importance of the local anthracite-mining industry to this general plan.At the invitation of the Peruvian Government, through the agency of David Dasso, chairman of Corpoacion Peruana del Santa, a technical mission was sent to Peru in March, April, and May 1945 to examine these coals and assist the corporation in promoting preparation of the coal for most effective use in the contemplated expansion of industry and trade."

Feb 1, 1948

By Paul M. Tyler

Hafnium appears to be among the more abundant of the newly discovered elements . Though quite widely distributed in nature , its compounds chemically so resembled those of zirconium , its sister element , that it escaped detection until 1923 , when Coster and Hevesy announced the discovery of the element , to which they gave the name of " hafnium " , from Hafniae , the Latin name for Copenhagen , where their research work was performed . Hafnium has so far been found only as a minor constituent of zirconium minerals . Zirconium as an element was discovered more than 140 years ago , but only a few unimportant uses were found for the metal or its compounds until some 18 years ago ; it is still classed among the rarer commercial metals . It is not surprising , therefore , that hafnium has not yet found a definite place for itself in industry . Nevertheless it has commanded a considerable interest among scientists ; and in 1930 some 70 grams of perfectly pure oxide of hafnium were prepared in Europe . A commercial future for hafnium is already glimpsed in the radio industry , and its high melting point and electronic emissivity have already led to the taking out of patents for its use in radio tubes and incandescent electric lamp filaments and for the cathode surfaces of devices such as X- ray tubes and rectifiers .

Apr 1, 1931

By A. J. Kraemer

The properties of crude petroleum continue to interest the Bureau of Mines and constitute an important phase of its major studies on the mineral resources of the United States. The Bureau's interest in the subject has been intensified by frequent requests for information on the characteristics of crude petroleum from various producing fields. Since its inception the Bureau of Mines has collected and analyzed samples of typical oils and at present has surveyed and classified crude petroleums from nearly all the known oil fields of the Western Hemisphere. Results of these surveys have been presented in various Bureau of Mines publications. (See bibliography, appendix A, p. 145.) The nature and comparative value of crude oils from various countries and the extent to which these oils may be considered potential competitors for markets are of manifest importance to the petroleum industry in all lands, largely because all crude oils, wherever produced, are either actual or potential competitors for a market with all other crude oils. The numerous discussions of foreign production of oil that have appeared in the technical press in the past indicate the great interest of the United States in this subject.

Jan 1, 1937