Search Documents

By E. R. Cole

Laboratory heats of an 80 percent copper high-leaded tin-bronze alloy, similar to Brass and Bronze Ingot Institute (BBII) alloy 3A, were made with reduced tin content to determine whether an alloy comparable to BBII alloy 3A could be produced using less tin to aid in conserving this strategic metal. The tin content was lowered from 10 percent to 8 percent and 5 percent (nominal values), respectively, and the reduction in tin was offset by either increasing the lead content or adding zinc. Mechanical properties, machinability, and corrosion characteristics of the resultant alloys were investigated, and the mechanical properties were compared with BBII typical values and American Society for Testing Materials (ASTM) minimums for high-leaded tin-bronze alloy. Results indicate that the tin content of this alloy could be reduced approximately 1 percent (difference between the 8.4 percent actual tin composition obtained and the 9.3 percent BBII minimum) without seriously affecting the desired properties. Results also show the tin content could be reduced without significantly increasing the chances of rejects for mechanical property failures, which might result from normal variations in the casting process.

Jan 1, 1972

By Doerner H. A.

From thermodynamic calculations Maier predicted that zinc oxide and methane would react at specified temperatures substantially according to equation (1). (1.) ZnO + CH4 = Zn (gas) + CO + 2H2. Other reactions that may take place are (2.) CH4 = C + 2H2. (3.) ZnO + CO = Zn (gas) + CO2. (4.) ZnO + H2 = Zn (gas) + H2O. Maier predicted that 870°C would be the critical temperature above which reaction (1) would take precedence over reaction (2) and that reaction (1), at equilibrium, would be substantially complete at or above 927°C. Theoretical considerations indicate that reaction (1) is reversible: this is supported, but not proved, by experimental data. The other reactions are known to be reversible. At low temperatures reaction (2) requires a catalyst and it is slow below 1000°C. Reactions (3) and (4) are rapid, but the equilibrium constants are such that only small concentrations of CO2 or H2O can be produced below 1000°C. Maier calculated that CO2 should not exceed 0.5 per cent at 870°C., and the calculation for water vapor gives a still smaller order of magnitude.

Jan 1, 1931

By W. F. Watts

This report describes the Mine Inspection Data Analysis System (MIDAS) developed by the Bureau of Mines to analyze the records of industrial hygiene samples collected by the Mine Safety and Health Administration (MSHA) in metal and nonmetal mines. MIDAS is the first system capable of sorting, editing, analyzing, and reporting these data. It is also the first system designed to be used by a number of Government agencies. At present the system contains 225,000 personal and area samples for 61 contaminants in 45 industries. The records date from 1974 to early 1980, and MSHA plans to provide yearly updates to the system. This report presents preliminary analyses of dust exposures and discusses the potential uses and limitations of these data. Analysis of the dust data for 1978 and 1979 showed that bagging had the highest percentage of dust overexposure. Morn than 40 pct of the 1,536 respirable quartz dust, total nuisance dust, and total silica dust samples exceeded the MSHA exposure limit. Other dusty occupations are ranked according to their percentage of overexposure.

Jan 1, 1981

By H. L. Burmeister

This is one of a series of publications by the Bureau of Mines dealing with mining methods and costs at representative operations in the United States. The report describes all phases of the mining methods for the open-pit operation and milling practices employed at the Vermont Asbestos Mines in Lamoille and Orleans counties, Vermont. A brief history of discovery and development of these asbestos deposits is given, and the ore deposits are described. Methods employed in exploration, sampling, and estimation of tonnage and grade are outlined. A breakdown of available cost figures is summarized in the last section. All asbestos ore produced in this area has been won by the use of surface-mining methods. Two quarries, the Lowell and the "C" Area, are in operation. The quarries combined are producing and the mill is processing approximately 3,500 tons of ore per 3-shift day The average 40,000 tons of crysotile asbestos fiber produced at this plant annually accounted for 96 to 98 percent of the total fiber produced in the United States in 1958. The mine is located (fig. 1) approximately 4 miles north of Eden Mills village on the southeastern flank of Belvidere Mountain (fig. 2).

Jan 1, 1962

By Gabriel S. Esterhuizen, Jarek Jakubec

In 2000, Laubscher’s Mining Rock Mass Rating (MRMR) classification system was updated and published. The new system brought a few fundamental changes that were in direct response to the challenges and problems encountered when applying the classification system in the mining environment, specifically caving operations. The fundamental changes introduced into the MRMR system in 2000 were the abandonment of the Rock Quality Designation (RQD) as an input parameter, accounting for healed and cemented joints, and the concept of rock block strength. The objective of this paper is not to discuss the role and usefulness of classification systems; the fact that classification systems are widely used in every stage of mining projects speaks for itself. This paper discusses some of the experiences gained with the MRMR 2000 system in various mining projects and shows how the changes to the system have resulted in improved assessment of rock mass conditions. Issues related to core logging for rock mass assessment are also presented.

Jan 5, 2007

By J. R. Thoenen

[For several years the Bureau of Mines conducted tests on ground vibration t emanating from quarry blasting in an effort to determine an index of destruction for different types of structures. Results of these studies have been published in four Bureau of Mines Reports of Invitations as well as in several articles in the trade and technical press.5/ The first paper (3)6/ discussed the subject in general and gave results s of a few blasting records. Some tentative theories also were advanced. The second paper (4) discussed results s of records made from blasting in a number of quarries.]

Jan 1, 1940

By Eugene T. Sheridan

The Bureau of Mines annually canvasses the fuel-briquet and packaged-fuel producers in the United States and publishes economic data on these industries, based upon reports submitted voluntarily by producers. This publication lists all producers that reported commercial production to the Bureau for 1960 and presents data on individual plants. The companies named herein represent virtually all producers of processed minerals fuels. A few small plants may not have been canvassed or failed to respond to the survey because some of the smaller plants operate intermittently and the survey is voluntary. All plants that reported commercial production were included; regardless of size. Specifically excluded were plants that manufactured briquets from wood charcoal. Fuel briquets and packaged fuel are manufactured solid fuels, produced by mixing fine-sized mineral fuels with binding materials and compressing into small individual shapes, Briquets are produced in pillow-shaped and cylindrical form, are 2 to 4 inches long, and weigh 2 to 4 ounces. Packaged fuel consists of 3- or 4-inch cubes; 6 or 8 of which are wrapped together in heavy kraft paper to form a package weighing 10 to 15 pounds, Briquets are durable and may be stored and handled as bulk fuel; packaged fuel breaks easily and must be stored indoors to prevent it from deteriorating. Whereas briquets are consumed in many areas as a general residential fuel, packaged fuel is more of a specialty item, used at times to supplement other fuels. Packaged fuel is burned without re-moving the paper and is referred to as the "white glove" fuel.

Jan 1, 1961

By A. E. Harak

To determine the retorting characteristics of a column of mine-run, ungraded oil shale ranging in size from fines to 5-ton pieces, a 150-ton batch-type retort was designed and constructed at the Bureau of Mines Laramie Energy Research Center, Laramie, Wyo. The retort vessel is 45 feet high by 11 ½ feet inside diameter, and is supported in a 95-foot-high steel superstructure. Mine-run shale from the Bureau of Mines facility near Rifle, Colo., assaying about 25 gallons of oil per ton, was used as the test shale. To date, 11 runs have been completed, and the results of the last 10 of these are reported. The effects of oxygen content of the retorting gas and the superficial gas velocity of the retorting gas on oil recovery from a column of mine-run oil shale were studied. In one run, the average particle size of the shale was substantially increased to determine its effect on oil yield. Oil recoveries ranged from a low of 39.3 to a high of 65.8 volume-percent of Fischer assay.

Jan 1, 1974

By R. D. Berkenkotter

Titanium and iron assays obtained from cores of three diamond-drill holes from the Cebolla Creek titaniferous iron deposit were evaluated by statistical techniques to obtain information concerning the mineral characteristics of the deposit and to make a preliminary determination of sampling requirements for the deposit. A range of sample volumes representing sizes from one-sixth NX core 2 feet in length through full NX core 10 feet in length were prepared by split-ting the NX core with a diamond saw and combining pulverized splits. Results indicate the existence of at least two statistical populations having different average grades of iron and titanium. Each has an assay frequency distribution that is not normal but is highly peaked (leptokurtic). Frequency distributions of assays from specific altered zones of the drill holes appear to be normally distributed. Increasing the cross-sectional area of the sample unit to change assay volume did not result in significant changes either in assay values or the resulting frequency distributions of assays. However, when assay volume is increased by increasing sample interval, the shape of the assay frequency distribution changes, and a normal distribution of assays is approached. Positive correlation exists between titanium and iron assays. The degree of correlation, although very significant, is too low to use for prediction purposes. Although the amount of data from three widely separated drill holes is not sufficient to establish an average grade for this large deposit, it indicates a range of expected assay values and provides some information for determining requirements of future sampling for evaluation purposes.

Jan 1, 1963

This Bureau of Mines report reviews the information presented at the Sixth Mineral Waste Utilization Symposium cosponsored by the Bureau of Mines, U.S. Department of the Interior, and the IIT Research Institute. Environmental scientists and engineers from nine countries participated in the symposium, which was held May 2-3, 1978, at the Chicago campus of IIT Research Institute. The 56 papers presented on the reclamation and recycling of mining and mineral wastes, municipal solid waste, industrial wastes, and scrap metal are summarized herein.

Jan 1, 1980

By Mary E. Cocklan-Vendl

Regulatory processes associated with development of major mining operations in Alaska and British columbia were evaluated using specific case studies. Included were one hard rock mine in Alaska (Red Dog Mine), one hard rock mine In British Columbia (Snip Mine), and one offshore gold dredging project in Alaska (WestGold SIMA). Based on a comparison of the three case studies, it became clear that the primary incentives for cost effective permitting are: 1) early and continuing coordination of proposed project plans, designs and schedules with key regulatory agencies and local area residents and 2) development of a sufficient level of baseline information on air quality, water quality, wetlands, endangered species, fish and wildlife, and socia-cultural conditions to support the required permit application. The U.S. permitting process worked in much the same way as the Canadian permitting process. Disincentives of mine permitting include high initial costs for baseline data gathering. However, a relatively high early investment resulted in more efficient permit acquisition and reduced long-term monitoring requirements. A common problem Identified was the inadequate supply of trained agency personnel with the requisite technical and permitting experience. This sometimes resulted in poor decisions and unnecessary changes in project plans and schedules.

Jan 1, 1993

By Lloyd H. Banning

Crucible-smelting tests at the Northwest. Electrodevelopment Laboratory and a pilot-plant test on electric smelting of western phosphate rock for the Westvaco Chlorine Products by the Tennessee Valley Authority indicated that the small vanadium content of the rock is concentrated in the ferrophosphorus by-product of Phosphorus smelting. This research is concerned' mainly with recovering vanadium and phosphorus froth the ferrophosphorus produced from western phosphate rock. Exploratory tests were made of several methods of treating vanadiferous ferrophosphorus. Attempts to separate vanadium as a carbide dross by saturating molten ferrophosphorus with carbon were unsuccessful. Volatilization of phosphorus from ferrophosphorus was accomplished to some extent, both with and without addition of sulfur in several forms, but elimination of phosphorus was not complete. Brief testing in a small experimental converter on oxidation of vanadium and phosphorus; into a slag by blowing with air showed promise. A method that comprised fusing vanadiferous ferrophosphorus mixed with soda ash under oxidizing conditions gave encouraging results and was tested beyond the preliminary stage. A slag product of the fusion contained most of the phosphorus and vanadium as water-soluble sodium phosphate and. virtually water-insoluble sodium vanadate. After leaching the sodium phosphate froth the slag, the leach residue was reroasted with soda ash and salt. This roasted product was leached again with water to extract the vanadium.

Jan 1, 1951

By S. H. Ash

For several years considerable activity has been devoted to economic and social factors affecting California metal-mining operations as they relate to accidents and their cost. The reason for this intense interest is that accidents cost this industry annually over $1100,000 in industrial insurance premiums for mines insured by insurance carriers only; during 1924-32, inclusive, they amounted to $3,616,9115. There are several reasons for this high cost, the most important of w rich are the consistently .high frequency and severity rates of injuries occurring in the industry. Coordination of effort, appreciation of a mutual problem, and widespread education are essential if accidents and their cost are to be reduced.

Jan 1, 1935

By Sam S. Taylor

In most oil fields, natural gas is the major source of energy causing flow of oil to the well. The amount of gas produced With the oil generally exceeds actual energy requirements, so that in time the gas reserve of the field becomes seriously depleted and the oil production nest be stimulated by some auxiliary means. One of these is to repressure the oil formation with natural gas; or, where a gas supply is not available, often air is used. Although air is a cheap and convenient repressuring medium, its use sometimes is attended with several disadvantages. First, the return air-gas mixture decreases rapidly in fuel value, often until it can be used no longer as a source of power. At the same time, explosive mixtures may result if recycling is used, causing hazards to life and equipment. Second, some fields experience considerable trouble with the formation of emulsions which become increasingly difficult to treat. Although there is no definite proof that air repressuring always causes these emulsions, many operators are convinced that this is the case.

Jan 1, 1934

By A. E. Raddatz

The Bureau of Mines is investigating methods for recovering tungsten from domestic resources. A calcine-quench-leach (CQL) technique was developed for the extraction of tungsten from the Golconda, Nev., hot springs ores. The deposit contains disseminated tungsten that cannot be beneficiated by conventional techniques and must be treated by hydro-metallurgical methods. The CQL procedure consists of calcining the ore at 900° C for 3 hours, quenching in a solution containing 1.5 parts of Na2C03 and 1.5 parts of NaOH per part of WO3 in the ore and at a solution-to-ore ratio of 3 to 1, leaching at 200° C and at 250 psig for 3 hours, and filtering and washing the residue. A series of closed-circuit batch tests showed that 92 pct of the tungsten was extracted from a sample containing 2.32 wt-pct W03. The pregnant solution contained 11 g/l W03.

Jan 1, 1982

By J. P. Bennett

Based on previous Bureau of Mines research indicating that improved high-temperature properties could be achieved for periclase refractories through chemical additions, the Bureau investigated the properties of full-size bricks produced from chemically modified periclase refractory grains and the suitability of making such chemical additions to Mg(OH)2 slurries prior to production of the periclase grains. In full-size brick testing, strength values, both hot and cold, for the optimized bricks were superior to those for a commercial 98-wt-pct-MgO refractory. The best results were obtained for a natural magnesite with an adjusted CaO:Si02 (C:S) ratio of 3.0 and a 1.0-wt-pct addition of Zr02 and for a seawater periclase with an adjusted C:S ratio of 2.5 and a 0.5-wt-pct addition of Mn02. For samples produced from chemically modified Mg(OH)2 slurries, additions of both Mn02 and Zr02 and an increase in C:S ratios produced significant increases in hot flexural strength, similar to those resulting from chemical additions made to periclase grains. The most effective modifications were additions of Mn02 to brine-derived periclases having a C:S ratio adjusted to 3.0. These results on chemically modified magnesia refractories indicate that such material could potentially substitute for magnesiachrome refractories containing imported chromite.

Jan 1, 1984

By B. W. Gandrud

This is the third report published by the Bureau of Mines concerning the washability of Black Creek coal. Both of the former reports5/6/ dealt with the Black Creek coal at the Bradford mine, Dixiana, Ala., near the northeastern extremity of the Warrior field, whereas the present report is based on float-and-sink tests of coal from what is presumably the Black Creek bed near the southern extremity of the field. Although the Yolande Coal & Coke Co., owners of the property at Yolanda No. 6 slope, consider this opening to be on the Black Creek bed, the authors do not feel that there is as yet positive proof that this correlation is correct. There has been little or no development of the Black Creek bed in the Yolande Basin in the past, and a posy-tine identification of the bed at Yolande No. o will have to await further exploration and development. The Yolande No. 6 is an exploration slope 3/4 mile north of Rockcastle, Ala. The slope is approximately 400 feet from top to bottom on a dip of 18° As fax as the authors can ascertain, coal has never been produced commercially from the Black Creek bed in the southwestern part of the Warrior field. Exploration work in the past has indicated that the Black Creek coal in. this area is extremely friable and high in sulfur. Extreme friability would naturally discourage its' use as a domestic and railroad fuel, and high sulfur content would be a disasvantage in its use for coking coal. The present study of this coal has been made with particular reference to sulfur elimination on the assumption that it would make a good coking coal provided enough of the sulfur could be eliminated by washing.

Jan 1, 1939

By D. Randolph Berry

The United States Bureau of Mines (USBM) awarded a contract to Foster-Miller, Inc. to develop guidelines for the storage and use of Self-Contained Self-Rescuers (SCSRs) in underground non-coal mines. An SCSR is a device capable of supplying, in an emergency, one hour of self-contained oxygen (no breathing of mine air). The information and recommendations in this report were developed primarily from three sources: discussions with mine representatives (including management, labor, and government), site visits in underground mines I and a detailed analysis of every reported non-coal accident which produced d hazardous atmosphere during the 5-year period 1976-1980 -plus ten other major incidents from prior years. Volume IV has three major sections: Recommendations and Discussion (Section 2), Analysis of Mine Accidents (Appendix A), and a Summary of Discussions with Mine Representatives (Appendix B).

Jan 1, 1983

By E. J. Gleim

The importance of "good voltage," especially for direct-current systems in coal mines, is not always fully appreciated. From the practical aspect there are three viewpoints from which low voltage may be considered, namely: (a) its effect upon operation of electrical equipment, (b) its effect upon cost of maintenance and power, and (c) its effect upon safety in the mine. The design of electrical motor-driven equipment usually is based upon a given or assumed constant value for the voltage of the system; consequently, when there is an appreciable drop below this value, unsatisfactory operation is likely to follow. In the case of shaker conveyors, for example, one manufacturer has pointed out that these conveyors must be operated at a certain definite speed if maximum output is to be secured. As shunt motors are used in the conveyor drives, either a rise or fall in voltage will produce corresponding changes in speed and thus seriously affect the efficiency of the conveyor. The introduction of automatic control for mine equipment has been greatly retarded because the relays, contactors, and other special devices required have failed to function properly when attempt was made to operate them on systems subject to variable and low-voltage conditions.

Jan 1, 1937

By John C. Machisak

THIS PUBLICATION presents injury experience and employment data for the nonmetal mining industry in the United States for 1960. Data for the mines and mills are presented separately, as shown in the list of tables. The Bureau of Mines is authorized to send questionnaires to the nonmetal mining industry for their voluntary submission of injury and employment data. As the information submitted contributes largely to the promotion of safety in the industry, special effort has been made to ma e these questionnaires as complete as possible.

Jan 1, 1963