Search Documents

By L. J. Kane

Several processes being developed by the Federal Bureau of Mines to provide new and more efficient uses for coal require practical methods for removing dust from hot gases. Filters provide such means. The efficiency of filters made of aluminum silicate fibers and porous stainless steel was determined. The results obtained with the fibers were previously reported.5 In this investigation tests were made with three porosities of stainless steel filter material (grades C, D, and E) at a gas flow of 1,000 std. c.f.h./sq. ft. of filter, temperatures of 75° and 1,000° F., and dust loadings (as represented by cumulative dust fed) of 100, 1,000, and 10,000 gr./sq. ft. of filter. Pressure drop during the runs ranged from 0.1 to 21 in. of mercury, and dust removal from 25 to 99.93 pct. Filters having the finest pores gave the greatest pressure drop and percentage of dust removal; however, their dust-holding capacity was slightly lower. Usually, their ability to remove a higher percentage of dust at the same pressure drop more than compensated for the slightly lower dust-holding capacity. With increase in temperature, for the same weight rate of flow of gas, the pressure drop increased and the percentage of dust removal decreased. The effect of temperature was probably due to the accompanying change in the linear velocity and viscosity of the gas.

Jan 1, 1961

By John Nagy

Tests were conducted in the Experimental coal mine to study some of the factors that should be considered in fighting mine fires and to obtain data on the effectiveness of different types of extinguishing agents. The investigation was confined to class "A" fires in a zone 20 feet long, involving coal burning on the floor, on the floor and ribs, and on the floor, ribs, and roof of the mine entry. It was determined that the time elapsed between ignition and attack of the fire is very important. A fire in the early stages was found to be controlled more easily and quickly than a similar fire that had burned longer. It was also found that, under suitable conditions, a fire in the floor, ribs, and roof develops very rapidly and consequently might spread over a considerable area if not brought under control quickly. The ventilating current affects fire-controlling operations markedly. Attack in intake or fresh air is highly advantageous, the chief inconvenience being the radiant heat from the fire. Attack in direct return air was impossible for the fires tested in this investigation, because of the high temperature. Universal-type gas masks for noxious gases and smoke offered no protection against the intense heat. Approach to a fire in the return air behind a water-fog curtain is not feasible unless the direction of air flow can be reversed. In one" test fresh air was carried to the fire area with a line brattice. Although the entire controlling operation was in fresh air and masks were not necessary, it was considerably more difficult to control the fire than when a similar fire was attacked in intake air.

Jan 1, 1950

By J. F. Messerly

The purity of three specially prepared samples of benzene was determined with an adiabatic, low-temperature calorimeter with automatic control of shield temperature. Extensive measurements were made on each sample to determine how variations in operating procedures affect melting-point and freezing-point as well as purity data obtained by the calorimetric method. Detailed results of the investigations are presented, and effects of different operating procedures are discussed, together with problems encountered in interpretating experimental results.

Jan 1, 1963

By F. P. Haver

The purpose of this investigation was to determine the effect of common impurities, that is, oxygen, nitrogen, carbon, and iron, on the Brinell hardness of electrolytic titanium. On a weight basis, nitrogen had the greatest hardening effect, followed by oxygen, carbon, and iron in order. The hardening effects of oxygen and carbon were almost identical up to a concentration of approximately 0.1 percent by weight. Above this concentration, the relative hardening effect of carbon decreased rapidly, possibly because of its limited solid solubility in a-titanium. Hardness vs. composition curves for both oxygen and nitrogen were essentially straight lines over the range of Brinell hardness numbers (B.h.n.) covered in the investigation. The hardness of titanium was also determined as a function of the percentage of impurity atoms. On this basis, iron in concentrations up to 0.17 atomic percent had a greater hardening effect than either oxygen or carbon. INTRODUCTION Determination of the as-cast hardness of arc-melted titanium is a method of quality control widely used in industry. Numerous studies4/ have been made of the effect of impurities on the hardness obtained by this method. However, most of them have been based on the use of either iodide titanium or commercially pure Kroll sponge (B.h.n. >90), as a starting material.

Jan 1, 1959

By L. J. E. Hofer

The Bureau of Mines determined rates of adsorption and desorption of methane as a function of particle size and temperature, using coals from the Pocahontas No.3 seam (lvb) from the Bishop mine of western Virginia, and the Pittsburgh seam (hvab) from the Pursglove No. 15 mine of northern West Virginia. For a given coal sample and temperature, the rate curves for adsorption and desorption are essentially the same when expressed on a fractional approach to equilibrium basis. The rates of adsorption and desorption increased eightfold as the particle size was decreased from 6-8 to 270-325 mesh per inch. The adsorption process appears to be diffusion controlled. Rate of sorption processes increased with increasing temperature; however, the amount adsorbed at equilibrium decreased.

Jan 1, 1966

By G. W. Jones

Gas analysis is of great practical value to the combustion engineer as a guide in the proper deli and operation of power and heating plants. The automotive industry, however, has made little use of gas analysis in the design and construction of engines. Tests4 made by the Bureau of Mines have shorn that for the average motor vehicle approximately 30 per cent of the heat value of the gasoline passes out in the exhaust as incomplete-combustion products. The tendency at present is to pay more attention to ease and flexibility of operation than to efficiency of combustion. However, neither condition can be fully realized except where each cylinder gets a mixture of the same composition - that is, when certain cylinders do not "load up" with gas at the expense of the others. When this occurs, due to some of the cylinders having too rich a mixture while in others it is too lean, it is impossible to get efficient combustion from the fuel used. Gas analysis enables the engineer to determine the quality of the mixture fed to the different cylinders with a high degree of precision. Briefly, the method consists in making an analysis of the exhaust gas from each cylinder while the engine is in operation.

Jan 1, 1924

By Frank J. Wiebelt, Spangler Hicker

The Iron Mountain investigations were part of a comprehensive program for making a national inventory of raw materials used in the production of steel. A tentative program of core drilling by the Bureau of Mines was set up for exploration of more promising iron deposits. Iron Mountain was selected as worthy of investigation because it could serve as a potential source of ore for the war-created steel plant at Fontana, Calif. The deposits were reported on by an engineer in October 1943. The purpose of the project was to determine the lateral and vertical extent of ore bodies and to obtain accurate material data on them.

Apr 1, 1948

By C. D. Litton

This Bureau of Mines report presents a set of guidelines for determining the distribution of product-of-combustion fire sensors in underground mines. Sensor spacing is defined in terms of sensor alarm threshold, ventilation flow rate, and mine entry dimensions. Sensor spacing guidelines are presented for detection of fires from two primary combustibles, coal and wood, which are common to the majority of underground mines. The guidelines are based on data from full-scale and intermediate-scale fire tests conducted by the Bureau of Mines.

Jan 1, 1983

By C. Melvin Lepper

High-resolution shallow seismic reflection methods are being used by the Bureau of Mines to map underground geologic features in coal mines. These features include faults, channel sand, washouts, rolls, and steep dips. The seismic method is proving useful for locating all of these at reasonable cost and with better definition than available with drill programs alone. This report provides a capsule description of the techniques and their application to mine planning.

Jan 1, 1976

By E. J. Lintner

This paper is one of a series being prepared by the United States Bureau of Mines describing clay mining and crushing methods and costs at various operations throughout the United States. These papers are designed to disseminate technical information regarding methods used. The cost tabulations represent local operating expenditures only and not total production costs. It is recognized that publication of total production costs might perhaps, in many instances, cause embarrassment to the individual operator as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of the methods employed. The attention of the reader is specifically called to this distinction in order that no misunderstanding of the scope of the cost tabulation shall ensue. The following report deals specifically with the methods employed by the Camp Brothers Company, Mogadore, Summit County, Ohio.

Jan 1, 1936

By K. C. Dean

Changes in the types of materials used for the construction of recent automobile models have occasioned a review of the continued applicability of current recycling techniques. Plastics are being used increasingly in late model cars. To evaluate the changes occurring, a 1972 Mercury Montego, furnished by the Ford Motor Co., was completely dismantled and analyzed, and the composition was compared with that of a composite automobile from 15 vehicles ranging in date of manufacture from 1954 to 1965 and designated as a circa 1960 model. The composite vehicle contained about 26 pounds of plastics, while the 1972 model contained over four times that quantity. The increasing use of plastics in automobiles suggests that research to improve the economic potentiality of plastics recycling is warranted.

Jan 1, 1974

By T. L. Marchewka

As part of its program to conserve the Nation's natural resources by developing improved performance materials, the Bureau of Mines, U.S. Department of the Interior, in cooperation with the U.S. Department of Energy, has conducted an investigation of materials of construction able to withstand the high temperature and hostile environments encountered in coal gasification units. Refractory pipe liners are required when extremely hot gases or abrasive solids are transported between processing units in the gasification plants. One promising technique for producing refractory pipe (or refractory pipe liners) is centrifugal casting. For this study, the effect of processing variables such as workability, additives, reinforcement and spinning time, and centrifugal force were evaluated using four commercial refractory concretes. In addition, data on characteristics such as strength, density, abrasion, and spalling resistance of 5-inch-diam refractory pipe were developed. Techniques for forming large-diameter (19-inch) refractory pipe also were evaluated. The test results indicated that all four refractory concretes could be made into strong, homogeneous pipe, but that optimum casting parameters had to be determined for each specific composition. The investigation revealed that the major controlling factor in the production of the centrifugally cast pipe was the workability of the refractory concrete.

Jan 1, 1979

By M. J. Ferrante

Enthalpy and entropy increments above 298.15° K were determined for cop-per sulfate between 298° and 1,000° K and for copper oxysulfate between 2980 and 1,146° K by the method of copper-block drop calorimetry. Enthalpies, entropies, and heat capacities are tabulated for both compounds. In addition, free-energy functions are tabulated for the sulfate. Equations representing the enthalpies are given for each compound.

Jan 1, 1972

By R. E. Head

[Surveys of the manganese situation conducted by the Geological Survey and other agencies have distinctly established the fact that the tonnage of high- grade manganese ore in the United States is relatively small. It is therefore obvious that large-scale production of manganese is possible only through beneficiation of low-grade material. ]

Jan 1, 1941

By W. H. Ode, W. A. Selvig

Briefly, this swelling test consists in heating 1 gram of pulverized coal in a silica crucible over a gas flame under prescribed conditions to form a coke button which is compared in size and shape with a series of standard profiles numbered 1 to 9. These profiles are intended to cover the size and shape of buttons obtained from coals covering a wide range in plastic properties. The number of the standard profile with which the maximum cross-sectional area of the button most nearly corresponds is recorded as the swelling index. Although the swelling test showed poor relationships with the various tests that were used for measuring expansion or contraction of coal during carbonization, it gave indications of having value in measuring free-swelling and coking properties of coals when burned on fuel tests. An opportunity to investigate this occurred when an engineering company reported pronounced differences in burning characteristics on grates of various shipments of Pocahontas coal. Some of these coals gave trouble by swelling excessively and clogging the grate. Samples were obtained, and it was found that the troublesome coals gave radically higher free-swelling numbers than did the coals that performed satisfactorily. Also, it was found that the free-swelling index test gave better differentiation between coals than could be obtained from the coke buttons from the standard volatile-matter test or iron agglutination-value results. The results of the free-swelling test were confirmed by the Subcommittee on Plasticity and Swelling, Coal, a special group of the Subcommittee, under the chairmanship of R.A. Shuman, worked along with the test method. Estberg, Limacher, and Shuman of the Battelle Memorial Institute investigated the various factors affecting the test and found that the swelling index was a good indication of the suitability of coal for performance on residential-type stokers from the swelling characteristics of the coal. Data were presented that also showed that the index was helpful in the selection of coal for industrial underfeed stokers.

Feb 1, 1948

By E. G. Valdez

Laboratory research demonstrated that ceramic wall and floor tile can be produced from electric furnace phosphorus slags composed of calcium silicates. Grinding the slag in a pebble mill, followed by magnetic removal of deleterious magnetite, produced a raw material that could be compounded and formed into wall tile by dry pressing, sintering, and glazing. The effects of process variables such as forming pressure and sintering temperature were investigated. Wall tile bodies produced by this method were comparable to commercial tile. The tiles were readily glazed to a smooth shiny finish and met ASTM Specifications C34-62 for structural clay load-bearing tile. The estimated cost of producing wall tile by this method compared favorably with the retail market value for similar wall tile. Addition of borax or other additives to the ground slag followed by dry pressing and firing likewise produced a commercial grade of floor tile.

Jan 1, 1974

By J. C. Franklin

The Bureau of Mines substantially reduced shale degradation in a coal mine by two spray coat applications of a water-base epoxy sealant. More than 12,700 square feet of passageways were treated, and in 18 months only one failure occurred. This failure was due to improper spray application, Material costs averaged 13 cents per square foot, and labor costs were 7 cents per square foot. Labor included moving all materials into the mine, the setup time for each of the areas coated, and application of coatings.

Jan 1, 1977

By John W. Cole

As part of a general preliminary investigation of lead-zinc deposits in Stevens County, Wash., the Electric Point and Gladstone mines on Gladstone Mountain, in the Northport Mining District, were examined by R. M. Gammell, an engineer of the Bureau of Mines, in June 1946. A trenching and sampling program was executed later the same year under' the supervision of Miro Mihelich and the author. This report presents the factual data obtained from the trenching and sampling operations.

Jan 1, 1949

By Harry Freund

Gallic acid is a sensitive, stable, colorimetric reagent for the determination of tantalum in the range of 2 to 40 µg.Ta/ml. The method consists of the fusion of tantalum oxide with potassium pyrosulfate and solution of the cooled melt in satu-rated ammonium oxalate, followed by development of a yellow complex with an ethanolic solution of gallic acid. The tantalum-gallic acid complex absorbs over a broad region in the blue and near ultraviolet. Adverse effects due to interfering ions and solution conditions, such as oxalate concentration and pH, can be minimized by a suitable choice of wave length. A new and sensitive colorimetric method is provided that has been used successfully at the Northwest Electrodevelopment Laboratory of the Federal Bureau of Mines for determining minor amounts of tantalum.

Jan 1, 1956

By D. Harrington

Springing or chambering of deep drill holes is common practice in some quarries. It involves definite hazards from premature explosion during placing of the springing charges or the final charge due chiefly to heating of the bottom of the holes by the successive exploding of the springing charges or, in some instances, from burning of paper or other material following detonation of the explosives The danger is either unknown or disregarded in many instances by those who place the charges in the holes. Disregard of this hazard probably is, at least in part, responsible for the far too high fatality and injury rate due to charging explosives and premature slots in quarry work. Awareness of the danger' should result in elimination or at least of material decrease in injuries from this cause.

Jan 1, 1941