Search Documents

Provide the U.S. mining industry with technology for designing environmentally sound, low-cost in situ leach mining operations to produce copper from small, deep, and/or low-grade copper oxide deposits. Approach Investigate the feasibility of a new mining method--in situ leach mining-as an alternative to conventional mining for copper. Study fundamental leaching technology that will facilitate future commercial operations. Develop guidelines and procedures that will enable mine operators to design and evaluate in situ leach mining operations for any specific copper oxide deposit.

Jan 1, 1989

By G. L. Oldright

This paper is the fourth of a series of preliminary papers on smelting in the lead blast furnace.4 The objects of this investigation are to determine the conditions obtaining within the blast furnace by direct experimentation and to correlate these conditions with operating factors, furnace behavior, and metallurgical losses. ACKNOWLEDGMENTS The authors wish to express their appreciation to the management of the International Smelting Co. at Tooele, Utah, for their whole-hearted cooperation in this investigation.

Jan 1, 1929

By Todd M. Ruff

Blind areas around construction equipment are a major contributing factor in incidents involving a piece of equipment striking a worker. In highway construction, these types of incidents result in an average of 22 deaths a year in the United States. The Spokane Research Laboratory of the National Institute for Occupational Safety and Health, in cooperation with the Washington State Department of Transportation, is evaluating methods to decrease these incidents. One such method uses devices that assist equipment operators in monitoring blind areas around the equipment to prevent collisions with workers or other objects. Several camera and sensor systems are available for this application. These systems were evaluated on various trucks used in road construction and maintenance. Tests were conducted on sanding trucks during the winter months, which allowed researchers to investigate the effectiveness and limitations of various technologies under the most extreme conditions. Tests were also conducted on dump trucks and utility vehicles during the warmer months to study the effectiveness of the systems in highway work zones. Results showed that many difficulties arise when using camera and sensor systems in cold, snowy climates. And, while the operation of these systems is more reliable during the warmer months, challenges still exist in using them on equipment in congested work areas.

By W. W. Adams

"The seventh National Safety Competition, that for 1931, conducted by the United States Bureau of Mines, was participated in by 350 mines and quarries operating in 34 States. Tables 1 to 5 show the relative standing of the various plants, Bronze trophies, known as the ""Sentinels of Safety,"" which were provided by The Explosives Engineer magazine to be awarded annually by the Bureau of Mines were awarded to five companies, each company having established the best accident—prevention record within one of the five classes into which all companies were divided — namely, anthracite mining companies, bituminous—coal mining companies, metal—mining companies, operators of nonmetallic mineral mines other than coal mines, and quarries or open—cut mines. The trophies are awarded for one year and are then transferred to the winners of the succeeding year's contest.The outstanding feature of the contest of 1931 was the operation of a bituminous coal mine without a lost—time injury to any employee. While accident—tree records had previously been made by certain quarries, metal mines, and nonmetallic mineral mines, never before has such a feat been accomplished by a bituminous coal mine in the National Safety Competition. Whether or not such a record has been made by a bituminous—coal mining company not enrolled is the competition the writer does not know, but it is believed that the case referred to is unique among large coal—mining companies. The mine to which reference is made is No. 1 mine of the Phelps Dodge Corporation, at Dawson, N. Mex. To that company belongs the distinction not only of being the first coal—mining company among those enrolled in these yearly safety contents to operate its mine without an accident but also of occasioning the 'Sentinels of Safety' trophy for a bituminous mine to take its first journey west of the Mississippi River. For the past six years the trophy has been in West Virginia, Alabama, or Pennsylvania."

Jun 1, 1932

The Bureau of Mines studied blast-produced ground vibration from surface mining to assess its damage and annoyance potential, and to determine safe levels and appropriate measurement techniques. Direct measurements were made of ground-vibration-produced structure responses and damage in 76 homes for 219 production blasts. These results were combined with damage data from nine other blasting studies, including the three analyzed previously for Bureau of Mines Bulletin 656. Save levels of ground vibration from blasting range from 0.5 to 2.0 in/sec peak particle velocity for residential-type structures. The damage threshold values are functions of the frequencies of the vibration transmitted into the residences and the types of construction. Particularly serious are the low-frequency vibrations that exist in soft foundation materials and/or result from long blast-to-residence distances. These vibrations produce not only structure resonances (4 to 12 Hz for whole structures and 10 to 25 Hz for mid walls) but also excessive levels of displacement and strain. Threshold damage was defined as the occurrence of cosmetic damage; that is, the most superficial interior cracking of the type that develops in all homes independent of blasting. Homes with plastered interior walls are more susceptible to blast-produced cracking then modern gypsum wallboard; the latter are adequately protected by a minimum particle velocity of approximately 0.75 in/ sec for frequencies below 40 Hz. Structure response amplification factors were measured; typical values were 1.5 for structures as a whole (racking) and 4 for midwalls, at their respective resonance frequencies. For blast vibrations above 40 Hz, all amplification factors for frame residential structures were less than unity. The human response and annoyance problem from ground vibration is aggravated by wall rattling, secondary noises, and the presence of airblast. Approximately 5 to 10 pct of the neighbors will judge peak particle velocity levels of 0.5 to 0.75 in/sec as "less than acceptable" (i.e., unacceptable) based on direct reactions to the vibration. Even lower levels cause psychological response problems, and thus social, economic, and public relations factors become critical for continued blasting.

Jan 1, 1980

By Kenneth D. Winters

This Bureau of Mines report presents a Fortran IV computer program for the structural analysis of (1) protective canopies used in underground mines to protect equipment operators from roof falls and (2) rollover protective structures (ROPS) used in surface mines to protect equipment operators during vehicle overturn accidents. The program, entitled PLASTIC CANOPY, permits rapid and inexpensive calculation of the ultimate strength and deformation characteristics of a canopy for a variety of static loading conditions. The structure is modeled as a series of interconnected beam and/or plate elements. Stresses in, and displacements of, each structural element are computed and printed out at the yield strength of the canopy, at several intermediate load levels between the yield and ultimate strength of the canopy, and at the ultimate strength of the canopy. Other features of the program include prediction of buckling of a beam member under combined axial compression loading and bending, plotting of the input geometry of the structure, and plotting of the deformed shape of the loaded structure. Program description, input instructions, program listing, and four example problems are included.

Jan 1, 1979

By Robert M. Doerr

The research objective was to determine the effect of aluminum alloy additions on the oxidation behavior of cobalt-nickel alloys. Thirty high-purity alloys were reacted with 02 at 0.5 atm at 1,351°, 1,389°, and 1,429° K in a volumetric apparatus for about 300 min. The alloy compositions consisted of Co-Ni master alloys (0, 22, 50, 70, 91, and 100 wt pct Ni) with aluminum additions of about 0, 1, 2, 4, and 8 wt pet. Large early deviations from, or changes in, the parabolic rate constant were encountered, but in most cases, the reaction rate declined approximately in accordance with the parabolic rate law. A sharp peak in the parabolic oxidation rate constant was observed for specimens containing a to 22 percent nickel and 1 to 2 percent aluminum at 1,351° K, and the rate constants for these compositions were lower at the higher temperatures. Specimens containing 8 percent aluminum reacted far more slowly than did any of the others.

Jan 1, 1971

By Vernon F. Swanson

Several laboratory flotation tests were conducted by the Bureau of Mines on a sample of unweathered diorite from the B. F. Camden property, Amherst County, Va. Results showed that an ilmenite concentrate analyzing 45.5 percent Ti02 (titania), 0.07 percent P205 (phosphorus pentoxide), and 2.21 percent Si02 (silicon dioxide) could be produced from a feed containing 7.72 percent Ti02 and 3.94 percent P205. Ti02 recovery in the concentrate was 47.6 percent in a batch test. The weathered saprolite material overlying the diorite required scrubbing and desliming to remove argillaceous material and preliminary flotation of apatite followed by flotation of ilmenite. The resulting concentrate analyzed 47.3 percent Ti02, 0.19 percent P205, and 0.99 percent Si02 from a starting feed of 8.99 percent Ti02 and 3.37 percent P205; TiO2 recovery was 54.5 percent.

Jan 1, 1963

By R. S. Dean

"It has long been recognized that the properties of polycrystalline substances are not the same as those of single crystals. These differences are especially marked in metels and metallic minerals, and are of greatest practical importance in metal working and ore treatment. The property changes encountered in passing from a metal single crystal to a poly-crystalline aggregate are the same as are produced by cold-working a metal or by the precipitation of a disperse phase. Hence, we may logically assume that the property changes are all due directly or indirectly to the formation of interfacial area or internal surface. Our problem, then, is to ascertain the physicochemical state of the metal atoms at such internal surface and show how this physicochemical condition accounts for the pronounced changes of mechanical, magnetic, and electrical properties that accompany increased internal surface.GENERAL CONCEPT OF INTERNAL SURFACEIn 1678, Huyghens attempted to explain the double refraction of calcite by postulating that crystals were built from a regular arrangement of ellipsoidal particles. Over 100 years later, Abbé Hauy concluded from his studies of cleavage that crystals might be built from small units, but the units were of the same shape as the entire crystal. This idea, which was prevalent in mineralogical thought before the advent of X-ray spectrometry, was discarded when the great success of Bragg made it appear that the chemical atoms were in reality the elements of structure. In the further development of X-ray technique, however, C. G. Darwin, in England, and P. P. Ewald, in Germany, found it necessary to postulate crystal units con¬taining many atoms. The latter gave the name of mosaic crystals to those so constituted. The individual units are supposed to Possess the ideal atomic arrangements revealed by the X-ray but are not oriented with respect to one another."

May 1, 1938

By Wm. F. Netzeband

"The mode of ore occurrence and the methods and costs of mining at one of the zinc-lead mines in the Tri-State zinc and lead district, Oklahoma, are presented in this paper for the information of mine operators in other districts.No. 2 mine property was acquired by lease in 1918 after some 30 holes had been drilled and a shaft had been sunk to the 305-foot level by the first lessees. After acquisition of the lease, the present operating company drilled a rich ore body on the 260-foot level and in 1920 started sinking two shafts. Production was begun late in 1921, and the mine has been operated more or less continuously to the present time.The mill has a capacity of 400 tons in 10 hours, the usual length of the mill shift in the district.The geology of Mine No. 2 is very similar to that of Mine No. 13 except that the Cherokee shale is thicker, ranging from 80 to 160 feet, and all the formations are correspondingly deeper, the Short Creek oolite horizon here being at a depth of about 300 feet. The oolite has not been found on this property, but the lime comes in at about the level at which the oolite should appear.The ore deposits of Mine No. 2 occur in the brecciated and bowlder ground above the Short Creek oolite. The main or 260-foot level is about 40 feet above the oolite horizon, and the lower or 300-foot level is immediately above it.The ore deposition is controlled by a zone of shearing and fracturing, and the mineable areas are divided into two distinct runs which have a northwest trend with a lean or practically barren area dividing them. This characteristic has controlled the mining to a large extent, for it enables the mine superintendent to locate the large pillars in lean ore and leave only small pillars in the richer ore. Figure 1 shows the outlines of the ore body and the pillars.The ore on the main level occurs disseminated throughout the jasperoid breccia as patches or lenses in the jasperoid, or cementing massive bowlders of jasperoid breccia and chert. The ore of the lower level is more of the bowlder type than that on the main level and occurs chiefly cementing the bowlders but also with some disseminated ore in the jasperoid breccia.The gangue minerals are jasperoid breccia, chert, and dolomite. Calcite is found in minor quantities. Sphalerite is the principal ore mineral; galena is found only in minor quantities around the edges of the ore body. When galena is encountered in this ore body, the limit of the ore can be expected.The exploration and estimation of ore reserves at Mine No. 2 are similar in many respects to the methods used at Mine No. 1.4After the mine was opened up and the general character of the ore deposit had been determined, drilling operations were concentrated along the trend of the shear zone. Later drilling has proved what appears to be a parallel shear zone or an offset of the zone now being mined."

May 1, 1929

By James H. McCutchan

The small and remote mine operators must comply with the Federal Mine Safety and Health Administration regulation requiring them to train and maintain mine rescue teams. The alternative is for the operators to contract with established teams within two hours travel time of their mine. Many of these remote operations are too far away from established teams and have too few employees to make up the necessary teams. Many cannot comply with the regulation either from a manpower or economic standpoint. The Office of Arizona State Mine Inspector, under the direction of the Honorable James H. McCutchan, State Mine Inspector, entered into a contract with the Bureau of Mines to develop the concept of a volunteer mine rescue program. This program with the assistance of the mining industry and volunteer rescue organizations, has planned and instituted a statewide volunteer mine rescue organization. The trained and equipped volunteers are stationed throughout the state and can respond to a mine emergency within the time constraints.

Jan 1, 1984

By G. R. Peterson

To determine the availability of lead and zinc from demonstrated resources, the Bureau of Mines evaluated 235 mines and deposits in 31 market economy countries. Of the 235 mines and deposits evaluated for this study, 186 were evaluated as zinc operations, 30 as lead operations, and 19 as copper operations. Demonstrated lead-zinc resources of market economy countries in 1981 were approximately 4.3 billion metric tons (t) of ore containing 221 million t of zinc and 97 million t of lead. Of these amounts, approximately 154 million t of zinc and 70 million t of lead are estimated to be recoverable. The analyses indicate that demonstrated resources in market economy countries should be sufficient to satisfy projected demand for primary lead and zinc through the balance of the century. The U.S. lead industry will continue to have a comparative advantage over the rest of the world industry, barring any drastic increase in the cost of compliance with pollution control regulations. It appears that the comparative disadvantage faced by the U.S. zinc industry will probably intensify owing to the relative quantity of lower cost zinc resources in other countries, especially Canada, Australia, Mexico, and Peru.

Jan 1, 1985

The objective of this condensed handbook is to provide the inspector with guidance for recognizing hazards from inhalation contaminants in above ground work areas of underground and surface coal mining and processing facilities and evaluating these hazards by collecting samples or making field determinations and interpreting the analytical results. It will be carried with the inspectors during their surveys. The complete handbook should be left in their offices except for Appendix II which lists the compositions of products found in previous surveys. There are several portions of the condensed handbook which should prove most useful to the inspectors. The names and locations of these portions are listed below: Procedure for an Industrial Hygiene Survey (Page 2-1) Survey Check List (Page 2-3) Rules for Determining if Sampling is Required (Page 2-2) List of Most Frequently Encountered Contaminants (Page 2-5) List of Candidate Contaminants and their Sampling Conditions (Page 2-A) Interpretation of Results (Page 3-8) For obtaining information not available from the above mentioned portions of the handbook, the inspector is directed to the Table of Contents, and the Glossary of Terms (Appendix I).

Jan 1, 1975

By Harry A. Schrecengost

The Bureau of Mines has found considerable lack of uniformity in style and content of record books used for reporting the results of examinations made by coal-mine officials. These books range from elaborate forms designed for specific examining and operating procedures at certain large mines to simple composition books, tablets, and pocket-style notebooks at other mines. Examination of thousands of these record books discloses that the reports of many examinations are so brief and so poorly worded that they cannot be understood readily. The contents, in some instances, appear to be deliberately ambiguous. The value of keeping accurate accounts of safety inspections in coal mines is often underestimated. Well-kept records reflect managerial attitude and indicate well-governed operations as well as training of official personnel to conform to considered policy and regulations and if necessary, may serve as documentary evidence to protect the mine officials and the operators.

Jan 1, 1962

By Oliver C. Ralston

[This paper is an expmded revision of a report entitled "Froth Flota- tion and Agglomerate Tabling of Honmetdlic Idinerds, " published in Trans- actions of the Canadian Ir-stitute of Iriining and !,letdlurgy (vol. 40, November 1937, pp- 6? 1-726) and al'enared a year pr~viousl:~. Revisions en'oodied herein brinc the &ta I:T to Jn?uac"g 1, 193;. References have also been added to make the earlier paper more complete for the period it covered. This paper is an expmded revision of a report entitled "Froth Flota- tion and Agglomerate Tabling of Honmetdlic Idinerds, " published in Trans- actions of the Canadian Ir-stitute of Iriining and !,letdlurgy (vol. 40, November 1937, pp- 6? 1-726) and al'enared a year pr~viousl:~. Revisions en'oodied herein brinc the &ta I:T to Jn?uac"g 1, 193;. References have also been added to make the earlier paper more complete for the period it covered.]

Jan 1, 1938

By G. S. Rice, H. O. Howarth, Greenwald. H. P.

"Electricity as a means of transmitting power was introduced in coal mines of the United States about 1891 for both haulage and coal cutting, only a few years after electrical haulage was first installed on street cars. At first, the hazards of electrical ignition ere not appreciated and the general use of open lights and black blasting powder made the possibility of electrical ignition of fire damp seem small by comparison.5 The possibility of igniting coal dust directly by electric sparks or arcs had not been considered.In the nine years prior to 1900, the progress of introducing electricity underground was slow, except that it was used for lighting shaft bottoms. Electricity had to contend with the more general use of compressed air for coal-cutting machines and, in mainline haulage, with the use of mule-teams and endless and tail-rope systems. During this period, great improvements were made in electrical apparatus, in surface installations as well as in mines. By 1900, therefore, the technique of applying electricity in mines had so far developed that it rapidly drove out the use of compressed air in coal mines because of the comparative ease of its installation and the marked economic advantages of its use over that of compressed air in practically all kinds of mining machines except percussion. rock drills.At this time, however, little thought was given to the hazard of indiscriminate use of electricity causing explosions and fires, and the possibility of electricity causing direct ignition of coal dust had not been considered. On December6, 1907, however, the Monongah, West Va. mine explosion occurred. This was the greatest mine disaster this country has over had, 361 men being killed. Although: there was much diversity of opinion, as to the origin of the explosion, many well-informed engineers concluded that the cause was ignition of coal dust do to wreckage of a runaway trip in a rope haulage entrance slope. This slope also served as a ventilating and it extended from the level of the coal bed to the surface. The runaway trip tore down electric cables and stirred up a cloud of dust when it was wrecked at the bottom of the slope. The dust was probably ignited by the electric arcing that occurred when the wires were knocked down. (Another but less probable source of ignition was the open flames of miners lamps.) From the foot of the slops the explosion appeared to have travelled into the mine, spreading as it went. If this ignition of coal dust was the origin of the explosion, it occurred on pure intake air entering directly from the surface."

Oct 1, 1930

By Kenneth O. Bayard, John D. Sullivan

"This repot continues the series of papers being prepared at the Southwest Experiment Station of the Bureau of Mines in cooperation with the department of mining and metallurgy, University of Arizona, on factors involved in the leaching of ores. A list of previous publications is given in the bibliography at the end of this paper.Four factors are essential to the leaching of any copper-bearing ore: (1) A solution that will attack the copper minerals must get into the body of the ore particles; (2) the copper minerals must be dissolved by the solution; (3) the solution containing the dissolved copper must find its way out of the voids of the rocks into the main solution; and (4) the copper in solution must be recovered by some means of precipitation.This paper considers the third step -- the extraction of the water-soluble copper. From leached ores. The usual commercial practice in leaching copper ores consists of: (1) Crushing the ore to pass through a screen with approximately one-quarter or one-third inch openings; (2) charging the crushed ore into a fat; (3) adding, usually by upward percolation, a solution that will attack the copper minerals; and (4) washing the copper-laden solutions out of the ore with solutions weaker in copper than the pregnant solution, and finally with water. A countercurrent system of leaching and washing is usually employed. In some plants the solutions are circulated during leaching and washing, and in others they are not. In some plants the wash solutions are added by upward percolation, while at Chuquicamata the so-called ""piston-displacement"" method of washing is employed.The following condensed resume of the leaching cycle of the plant of the Inspiration Consolidated Copper Co. is given to present to the reader a picture of the steps involved in a typical leaching cycle. This plant was recently described in detail.4 The ore, crushed to pass openings 11/2 inches in diameter, passes over a screen with ¼-inch openings. The undersize from the screen goes to a Dorr howl classifier that removes the primary slime from the circuit. The overflow from the classifier is treated in a slime-leaching plant. The oversize of the ¼-inch screen passes through rolls, where it is crushed to pass a 3/8-inchscreen. The undersize from the 3/8-inch screen join with the coarse material from the classifier, and the combined products become the feed to the leaching vats. There are 13 concrete lead-lined leaching vats. The complete leaching cycle is 13 days. Eight tanks are under acid-iron content at all times; three are being washed, one tank is being filled, and the one is being excavated. The electrolyzed solution from the tank house, to which amount of new acid has been added, is put on the oldest tank of ore under need This solution travels from tank to tank and finally emerges from the newest ore"

Apr 1, 1931

By G. H. West, R. L. Sebastian, W. A. Darror

"This bibliography was compiled in the course of research work by the Bureau of Mines on the utilization of magnesites in the West. The results of the research will appear as a bulletin of the Bureau.1. ANALYTICAL METHODS. 11 Knight, X. and Wheeler, W.H. Proc. Iowa Acad. Sci., 13, 1907, 167 (C.A.1, 1370). Describes experience in analysing calcite and dolomite. Reports great excess of oxalate unnecessary and separation of sulphates by alcohol is best.2 Meyerhofer, J. Zeit, Angew. Chem., 21, 1908, 592. Direct determination of Mg as phosphate after removal of SiC2, by keeping R203 in solution with ammonium citrate.3 Merckschen Guano Phosphat Werke. Chem. Ztg., 33, 1909, 545 (C.A. 3, 2281). volumetric analytical methods.4 Popel, M. Zeit. Angew. Chem., 21, 1908. 2082 (C.A, 6, 412). Determination of CaO in presence of CaC03.5 Blasdale, W.C. Jour. Am. Chem. Soc., 31, 1909, 91? (C.A. 3, 2658). Studies of separation of Ca from Mg.6 Hundeshrgen, F. Zeit. Offent. Chem., 15, 1909, 85 (C.A. 3, 1853). Valua¬tion of caustic magnesia by analysis. Volumetric methods.7 Frerichs, H. and Krosberg, W. Apoth. Zeit., 24, 1909. 679 (C.A. 3, 2996). Tecting magnesia alba for Fe.8 Schoorl, N. Zeit. Anal, Chem., 48, 1009, 593 (C.A. 4, 5E9). Microchemical tests for Mg, Li, K. and Na.9 Heyer. Chew. 2Ag., 33, 1009, 1157 (C.A. 4, 1588). Determination of CaO in presence of CaCO3. CaCO3 in soluble in cold neutral solution of NH3 salts. Solubility Is diminished by free NH4OH."

Oct 1, 1923

By M. J. Beus, B. Stewart, S. Iverson

Synopsis U.S. Mine Safety and Health Administration (MSHA) accidents statistics have identified ore-pass hazards as a significant safety problem in U.S. underground metal mines. The statistics show that nearly 75% of injuries are directly or indirectly related to pulling or freeing of ore-pass chutes, the use of hand tools in ore passes, fails of broken rock in ore passes and structural failures of chutes or gates and ore-pass walls. Researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) are investigating hazards in and around ore passes in hard rock mines. Risk assessment methods, such as fault-tree analysis, have been employed to identify the most probable causes of orepass failures, define research priorities and analyse the factors that result in malfunctioning and unsafe ore passes. Static and dynamic loads are being measured in a laboratory setting with the use of a reduced-scale orepass mock-up. Field tests are being initiated in mine ore passes to determine static and dynamic loads. Data from the test ore passes are being compared with data from the mine to characterize true system behaviour. Computer modelling with the use of closed-form solutions, finite-element analyses and a newly developed particle flow code predicts static and dynamic leads from the flow and the impact of ore and waste in the ore pass. Preliminary results indicate that dynamic impacts from ore and waste rock might be considerably greater than expected. The total static load is substantially less than is typically used fur the structural design of chute and gate support members. It is suggested that damping factors, normal and shear stiffness and mass frictional characteristics have a significant effect on particle flow and resulting impact loads. This is being verified with the use of results from laboratory tests, field tests and particle flow analyses. Ore passes are vertical or steeply inclined openings in a rock mass through which ore and waste are transported and where they mar also be stored. A typical underground mining system is shown in Fig. 1. The arrows indicate the locations of ore passes and loading pockets and their relative configurations. The control of material flow is potentially one of the most hazardous operations in underground mining. According to MSHA data. most of the ore pass-related accidents in the U.S.A. are associated with the loading-unloading cycle and removal of blockages from ore passes. In particular, attempts to free ore hang-ups have resulted in multiple fatalities. The hazards are obvious; there is uncertainty as to when the ore will break loose and miners are unable to escape falling rock to a safe location. Although ore passes and chutes and gate systems for underground metal and non-metal mines roust meet the requirements specified in the U.S. Code of Federal Regulations (CFR). Parts 57 and 75, recent structural failures of ore-pass linings and gates have underlined the lack of adequate ore-pass design standards available to both MSHA enforcement staff and mine engineers. Because of the importance of an ore pass to the safe operation of a mine design criteria need to be assessed and new guidelines developed. Researchers at the Spokane Research Laboratory of the Nationals Institute for Occupational Safety and Health (NIOSH) are investigating hazards in and around ore passes in hard rock mines and studying design criteria for ore passes. The near-term goal is to conduct laboratory and field experiments and computer modelling to evaluate the ore-pass design criteria currently used. Literature searches, field site

By M. A. Trevits, I. R. Houlison, A. C. Smith, T. P. Mucho

Timely and rapid intervention to underground combustion events (fires, explosions, and spontaneous combustion) is the key to the successful control of the mine atmosphere and restoring of a coal mine to production. The focus of this paper is the utilization of a GAG 3A jet engine system to combat either large out-of-control fires or to render an entire mine inert when access to problem areas is difficult or impossible. This system is based upon a Soviet designed agricultural jet engine which consumes aviation fuel with oxygen (O2) from the intake air and exhausts combustion gases, primarily carbon dioxide (CO2) and water (H2O), along with the nitrogen (N2) from the air and small amounts of carbon monoxide (CO) and hydrogen (H2). The system is designed to approach stoichiometric combustion (ideally, pure burning that scavenges all the oxygen from the intake air). Therefore, these exhaust gases are almost entirely “inert gases”- i.e., gases which do not contribute to, and in fact, can suppress the combustion process due to the lack of oxygen. Other methods to inert mine areas have been used in the US and internationally, but these methods usually use low flow inertisation equipment or methods. Use of these low-flow inertisation equipment and methods has been successful in proactively rendering gob areas inert and has the ability to inert the entire mine workings. Due to the low flow rate, however, a substantial period of