Search Documents

By G. R. Hopkins

The average quantity of heat needed to refine a barrel of crude oil in 1934 was 638,000 B.t.u., or about as much heat energy as contained in 5 gallons of fuel oil. Although the total heat utilized in 1934 was slightly above 1933, crude runs to stills increased 4 percent, hence the average requirement per barrel declined from 660,000 B.t.u. in 1933 to 638,000 B.t.u. in 1934 (see fig. 1). The average for 1934 constitutes a new record for firing efficiency, being just under the previous low of 1929. Heat consumption at refineries depends on many factors, of which the trends in yields of gasoline and lubricating oils are probably most important. The yield of gasoline is indicative of activity at cracking plants, which type of plant utilizes more than the average amount of heat per gallon of product. The yield of lubricating oils is indicative of the extent to which credo oil is refined; that is, it takes considerably more heat to refine a barrel of crude through lubricating oils than it does to separate only gasoline and kerosene. The yield of gasoline decreased from 43.7 percent in 1933 to 43.4 percent in 1934; on the other hand, the yield of gas oil and fuel oil increased. Although the yield of lubricating oils increased slightly in 1934 the theoretical increase in fuel requirements probably was offset by technical improvements, such as solvent refining.

Jan 1, 1935

By John J. Henn

An economic evaluation was made of the Bureau of Mines incinerator residue separation process to update the one published in 1971 to a mid-1.974 cost basis. This evaluation includes a modification of the glass-recovery operation used In the original plant design as well as a unit to bale the ferrous scrap product before shipment. Products from the plant are ferrous metal, aluminum and copper-zinc scrap, and a mixed-color glass cullet. The estimated capital and operating costs for four plant sizes are as follows : [ ] The operating costs do not include credits for recovered metals and glass.

Jan 1, 1975

By J. A. Herdlick

"INTRODUCTION The BeVan quartz crystal prospect in the Indian Creek mining district of Lemhi County, west-central Idaho, was examined by an engineer of the Bureau of Mines 3/ on July 9, 1943. As quartz crystals possessing peizoelectric properties were on the critical list of strategic war minerals, further exploration of the deposit was recommended. The Bureau of Mines exploration began in December 1943 and continued through January 1944. Additional trenching was completed during May and June 1944. This report presents the data obtained by this exploration.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. The Mining Division, Lowell B. Moon, chief, conducts preliminary examinations, does the actual exploratoiy work, and prepares the final report. The Metallurgical Division, O. C. Ralston, chief, analyses samples and makes beneficiation tests.The quartz crystals found during the exploration were examined and classified at the Bureau of Mines College Park, Md., laboratory and checked at the National Bureau of Standards, Washington, D. C.Fred BeVan, of North Fork, Idaho, and Edward F. Cenis, of the Montana Coal & Iron Company, Spoane, Wash., provided much information on the history and past production of the property."

Mar 1, 1948

By Jeffrey Shawn Peterson

The testing procedures of the U.S. Mine Safety and Health Administration specify that intrinsic safety acceptance tests be conducted using a standard tungsten-cadmium electrode configuration in the break- flash apparatus. However, in realistic mining environments, other materials may be more likely sources of sparking. Information defining the probability of spark ignition between common materials such as aluminum, brass, copper, lead, tin, cold-rolled steel, and stainless steel is of more practical value in determining ignition hazards. The U.S. Bureau of Mines has completed an investigation of the influence of material on the ignition probability using the breakflash apparatus. By comparing ignition currents or ignition voltages corresponding to a probability of one ignition per thousand sparks to those found previously for cadmium, a margin of safety may be estimated for each material. This report presents the results of an investigation into the influence of disk electrode material on the probability of ignition.

Jan 1, 1992

By J. M. Stuve

Low-temperature heat capacities of chiolite (Na5Al3F14) were determined by adiabatic calorimetry in the temperature range 5.8 to 300 K. The derived standard entropy (S°, 298.15) was 115.6 ± 0.2 cal/deg-mole. High temperature enthalpies relative to 298.15 K were obtained by precision drop calorimetry up to 1,000 K. Tables of experimental data and related thermodynamic functions are given for the temperature range of experimental observations.

Jan 1, 1980

Alabama ranked 19th in the Nation in nonfuel mineral value1 in 1994, down from 18th in 1993, according to the U.S. Bureau of Mines. The estimated value for 1994 was $576 million, a 2.5% increase over that of 1993. This followed a 3.5% increase in 1993 over that of 1992. The State accounted for a little less than 2% of the U.S. total. Nonfuel mineral production in Alabama consisted entirely of industrial minerals; no metals were mined in the State. Bauxite materials mined in the State are a natural mixture of bauxitic clay and bauxite having very low iron oxide content and are primarily used to make refractory (high temperature resistant) products, rather than in the production of primary aluminum. In descending order of dollar value, the top four mineral commodities produced in Alabama were crushed stone, portland cement, lime, and construction sand and gravel. These commodities accounted for almost 88 % of the State's total non fuel mineral value, while crushed stone and portland cement together represented almost 65 % of the total. In estimated mineral production for 1994, Alabama remained first in common clays and first of only two States that produced bauxite; third in lime, kaolin clays, and fire clays; seventh in portland cement and salt; and was one of the top seven States that produce bentonite clays. The State dropped from third to fifth in masonry cement. Production of talc and pyrophyllite resumed in 1994. Compared with 1993, the value of crushed stone, lime, construction sand and gravel, common clays, kaolin clays, fire clays, bauxite, and talc and pyrophyllite increased. Decreases occurred in portland cement, masonry cement, industrial sand and gravel, and dimension stone.

Jan 1, 1995

By Laurence G. Trudell

Geology and oil-yield data are presented for a 58-square-mile area encompassing the U.S. Department of the Interior oil-shale leasing program tracts in the western Washakie Basin, Sweetwater County, Wyo. Lithology and oil yields of samples from three Bureau of Mines coreholes are evaluated and correlated with Kinney Rim surface sections measured and sampled by the U.S. Geological Survey. Minable sections of oil shale averaging up to 25 gallons of oil per ton crop out on Kinney Rim in the Laney Member of the Green River Formation. Thick oil-shale sections in the Laney Member that average 15 gallons per ton represent 155 million barrels of oil in place per square mile. In the lower part of the Green River Formation the Tipton Shale Member contains a 20-to 40-foot section averaging 15 gallons per ton. Beds of high-volatile C bituminous coal up to 6 feet thick are present in intertongued parts of the lower Green River Formation and upper Wasatch Formation.

Jan 1, 1973

By C. R. Kuzell

This paper, describing the concentrator practice of the United Verde Copper Co., is one of a series being prepared by the Bureau of HISTORY The United Verde concentrator was constructed in accordance with recommendations based on certain novel reasons which were quite different from those usually justifying the expenditure of such an amount. Concentrator operations started in March, 1927, although the metallurgical staff had considered for several years the eventual addition of a concentrator department.

Jan 1, 1930

By J. E. Conley

[Available statistics show that the demands of the American chemical industry for sodium sulphate have been increasing slightly in recent years. The supply from domestic sources, particularly in the form of byproduct salt cake from the acid manufacturers, has been tending to decease due to the growing manufacture of synthetic acid. Both hydrochloric and nitric acids are being synthesized from their elements. The natural result has been that a smaller amount of salt cake is available. Simultaneously, the expansion of the Kraft-paper industry, especially in Lie South, has brought about greater demand for sodium sulphate in that section. This demand is being met by domestic byproduct salt cake, by imported German sodium sulphate made from potash waste liquors, and by favorably situated domestic deposits of Glauber salts and tile anhydrous salt, thenardite. No shortage of natural sodium sulphate exists in the United States, but usually such deposits occur in semiarid regions far re¬moved from transportation facilities and from markets. Moreover, the major portion of the natural deposits is Glauber salt or mirabilite (Na2SO4?10H20), which must be dried or dehydrated in order to most consumer requirements. The waters of hydration represents, roughly, 55 percent of tae total weight of the crude salts and therefore has a very important influence on transportation costs. In marry instances the cost of getting even the dehydrated product to market is the deciding economic factor. Therefore, the recovery or production of anhydrous sodium sulphate from plant-waste liquors or from natural brines of suitable composition might be economically feasible.]

Jan 1, 1936

By D. E. Wolfson

The Bureau of Mines carbonized 21 coal samples from Fayette, Greene, and Washington Counties, Pa., at 900° C, using the Bureau of Mines-American Gas Association (BM-AGA) method, and determined yields of products and physical properties of the coke. These samples represented high-volatile A Pittsburgh, Sewickley, Waynesburg, and Upper Freeport and medium-volatile Upper Freeport and Lower Kittanning coals. About 20 percent of all coals presently carbonized in commercial coke ovens in the United States are mined in Greene and Washington Counties, principally from the Pittsburgh seam. Sulfur content of the Pittsburgh coals in these counties is moderately high (1.0 to 3.2 percent) but, because of extremely large reserves, accessibility to eastern United States markets and excellent blending characteristics to yield strong coke, these counties will continue to be an important source of metallurgical coals in the future. Most coals from the other seams contained more than 2 percent sulfur, which would limit their use as metallurgical coals.

Jan 1, 1968

By Brian G. White

Two examples of en echelon mining-induced fractures seen in hard-rock mines provided a basis for inferring that fracture zones and bedding plane separations immediately surrounding mine openings are promoted by oblique shear into the openings. It is hypothesized that initial fractures or separations form at the corners of openings as a result of high stress and physical constraint on the rock's ability to deform elastically toward the opening. These conditions result in a locally preferred direction of shearing. The shearing, in turn, generates tensile stress that initiates a progression of systematically offset fractures approximately parallel to the direction of greatest compressive stress. The fractures or bedding separations create tabular rock layers that amplify shearing displacement through bending and dilation. Such shearing effectively reduces and redistributes the compressive stress, but significant dilation is an inevitable consequence. The combination of dilation and shearing and the progressive development of fracture zones have important implications with respect to ground support. The concept of mining-induced fractures forming as a result of shear is illustrated by two examples from coal mines. First, fractures seen at longwall faces probably result from shear associated with subsidence. The fracture zone that develops approximates or possibly defines the draw angle of subsidence. As the face advances, fractures extend downward along the lower edge of the fracture zone, while upper extensions of the fractures are pressed closed. Fracture zones in entry roofs provide a second practical example. Here, mining-induced fractures typically follow bedding planes. The shear zone model suggests that the first bedding separations develop near the edges of the roof and successive separations progress upward and toward the center. However, if the direction of greatest stress is inclined with respect to the roof, a fracture or bedding separation zone may propagate from one side only and also extend higher. Because coal ahead of the face provides some support against lateral shear deformation, bedding separation is inhibited near the face. Rock bolts installed close to the face ultimately become more strained and bent than bolts installed a few meters from the face, and bolts installed through the more remote part of a separation zone may ultimately experience the greatest tensile and bending strains. This model is supported by field data documenting progressive bolt failures that rapidly propagated downward across the roof during face advance.

By Donald S. Colby

CARBON-BLACK shipments, which had declined in the latter art of 1953, remained low in 1954 until after settlement of the labor strike that occurred in the rubber industry in July and August. The production of new model automobiles in the last quarter of the year spurred the demand for rubber tires and consequently the demand for carbon black. Total shipments of 1,498 million pounds for the year were 4 percent below 1953.

Jan 1, 1958

By Haskiel R. Shell

While the original purpose of the Bureau of Mines work on fluorine micas was to synthesize large single crystals or film suitable to replace natural muscovite or phlogopite, the objective was broadened to include development of the many possible fluorine micas as a class of new, unique materials. Several methods were developed for the synthesis of the fluorine micas at atmospheric pressure: Solid state reaction, melting in crucibles, internal resistance electric melting, and arc resistance electric melting. The latter two methods are now med commercially. A variety of fluoromicas were synthesized by isomorphic substitution including disilicic, trisilicic, and tetrasilicic. Fluorophlogopite, KMg3AlSi3O10F2, is the fluoromica most widely used. While most of the fluoromicas are completely stable to water, many water-swelling fluoromicas and fluoromontmorrilonoids were synthesized. Single crystals or film of the fluorine micas were grown to 2 inches or more by a number of methods, but none has as yet proved economical. In the report, detailed data and descriptions are given on compositions, syntheses, products, and uses, and on the properties including physical, dielectric, chemical, X-ray, optical, and structural.

Jan 1, 1969

By R. S. DeCesare

Operation of the Bureau of Mines raw refuse continuous separation pilot plant is described, including modifications made to plant equipment for improved performance. Products recovered from refuse, many of which have been evaluated by other laboratories and private firms, are discussed. Sampling procedures used in the pilot plant and detailed data obtained from processing refuse from 13 municipalities are presented in appendixes. Fuel evaluations made on combustible fractions of refuse from the various municipalities are also presented. Information and data obtained at the pilot plant have been used to assist many municipalities in solving their urban refuse problems.

Jan 1, 1980

By L. A. Readdy

No text. A set of geophysical well logs for U.S. B.M. Pilot Hole "X", Piceance Creek Basin, Colorado.

Jan 1, 1977

By J. Burlin Johnson

In small-scale blasting experiments conducted in the Bureau of Mines laboratory, small charges were used to produce craters in blocks of concrete mortar. The results are compared with larger scale experiments of other research workers, and the comparison demonstrates the similarity of the results obtained and indicates that small-scale blasting should be a useful tool for predicting large-scale blasting effects. INTRODUCTION The purpose at this investigation was to conduct blasting experiments in mortar in the laboratory and then, by comparing the results with those from larger scale field blasts in rock to determine to what extent, if any, the laboratory results resemble those in the field. The work described herein was the initial phase of a project aimed at evaluating small-scale blasting as a tool for use in improving blasting techniques. It is evident from the stand-point of control and cost that small-scale blasting would be valuable in the study of rock fragmentation by blasting in mines and quarries, if the extrapolation is valid.

Jan 1, 1962

By J. Dean Warner

In 1984, as part of a project to evaluate Alaskan occurrences of certain critical and strategic minerals, the Bureau of Mines investigated a columbium-bearing regolith on upper Idaho Gulch, near Tofty, AK. The regolith is derived from weathering of a dolomitic marble and consists mostly of iron oxide minerals with accessory apatite, zircon, xenotime, rutile, monazite, and the columbium minerals aeschynite, columbite, and ilmenorutile. Two regolith lenses contain 340,000 lb of columbium resources at an average grade of 0.07 pct. Calculated composite concentrates from two regolith samples (approximately 200 lb each) contained 53 and 57 pct of the columbium at grades of 0.97 and 0.86 pct, respectively. In each case the grade could be improved to 1.1 pct Cb with a sacrifice of 9-pct recovery. The regolith's mineralogy, trace-element geochemistry, and similarity to descriptions of other columbium-enriched regoliths suggest that the underlying marble may be a carbonatite. The lack of associated alkalic igneous rocks and the stratiform nature of the regolith, however, may be interpreted as evidence for sedimentary origin of the marble. The marble and regolith are a lode source for some of the minerals in the Idaho Gulch placer deposit.

Jan 1, 1986

By J. B. Littlefield

[Ata. meeting of the Subcommi ttce on Chemical _ et.lOds of Air Ant:..1ysis of-the American Public Health Ascociation in October 1937, the llse of the impinger for collectinG lcs.d fu.l1e wa:., discussed. The Bureau of Mnes de-cided to obtain infornw.tion on the efficiency of the lerge and midget im-pingers for this purpose y using the electric recipitator as a reference method. 'I'ests ~ ere made aJ,so to aScer ain the effici ency of the recently developed midget i;npi gerS..! for collac ing lead dust. For comparative pur-poses, samples collected by tte large impinger wore included.]

Jan 1, 1938

By Thomas M. Barczak

The transverse loading requirement for stoppings as specified in the current Code of Federal Regulations is 39 psf. This measure is based on physical testing of a freestanding wall in accordance with ASTM E 72 specifications, where the dominant parameter is the tensile strength of the sealant. A new protocol based on arching has been developed to determine the true transverse load capacity of stoppings. Arching is achieved by the restraint of the stopping against the mine roof and floor, whereby compressive forces are developed within the wall. A laboratory procedure using the NIOSH Mine Roof Simulator (MRS) to simulate rigid-arching of stoppings was developed and verified through full-scale in-mine tests. Using this protocol, a systematic study of the design parameters that affect arching capability in block stoppings was conducted. The study included a theoretical assessment of arching and development of design formulations that can accurately define the transverse load capacity of various stopping constructions under various loading conditions. This approach should lead to a safer mine environment by matching the transverse load capabilities of the stopping design to the requirements in the mine to ensure proper ventilation control is maintained.

Jan 1, 2005

By Jacob N. Frank

A factorially designed, hydraulic fragmentation experiment using a high-pressure water jet was conducted on concrete blocks. Three levels of pressure, standoff distance, and impact angle and two levels of traverse time and surface condition were used. Three variables were measured: depth of penetration, volume of material removed, and width of slot. Three stepwise linear regression equations were developed from the jet parameters and the physical properties of the concrete. The three basic equations, describing the significant jet parameters and physical properties, were developed into 15 predictor equations, five for each variable investigated. Direct regression equations were also developed for each variable investigated to show the result of increasing or decreasing each significant variable. Energy efficiencies were developed for the experiment and for each significant factorial variable.

Jan 1, 1971