Search Documents

By Frank Parrish

History and performance data of 17 water-injection projects in Cooke and Grayson Counties in north Texas are presented for the purpose of studying and comparing operating practices and oil-recovery techniques. Water is injected into Strawn and Canyon sands of Pennsylvanian age. The principal formation flooded is the Strawn, which ranges in depth from 725 to 6,900 ft in the projects covered. Estimated ultimate recoveries range as follows: Primary, 22 to 494 bbl per acre ft; and secondary; 63 to 296 bbl per acre ft. These figures represent the following percentages of original oil in place: Primary, 10 to 46 pct; and secondary, 8 to 23 pct. Shallower projects; 725 to 1,500 ft in depth, had higher average primary and secondary recoveries than did deeper projects. Crude-oil gravity, which ranges from 20° to 45° API, was not relatable to yield of secondary recovery oil. Analysis of the data indicates that five-spot injection patterns will yield the highest percentage of oil remaining at start of flooding; that is, 28.8 pct for five-spot injection patterns, compared with 20.8 pct for line-drive patterns and 11.6 pct for random patterns. Waterflooding in this area appears to be very successful. Secondary recoveries of most projects are expected to nearly equal primary recoveries.

Jan 1, 1963

By Paul J. Remington

The field data gathered as part of the measurements described in Volumes I and II were re-analyzed in the low frequency regime (.1 Hz to 1 Hz) where motion sickness normally occurs. These data were compared co the international standard ?ISO 2631 Addendum 2: Evaluation of exposure to whole body z-axis vertical vibration in the frequency range 0.1 to 1.0 Hz." For both underground mining machines and surface mining machines the results showed that one would not expect motion sickness to .be a severe problem. New field data were gathered on the vibration reduction performance of various seat designs found on surface coal mining machines. The vibration during normal operation was measured on the seat using the standard seat pad accelerometer package described in the previous two volumes and simultaneously on the floor of the machine at the base of the seat. Preliminary indications are that the so-called high performance seats used for operator vibration reduction do not offer significant improvement over conventional seats.

Jan 1, 1984

By Paul S. Goodman

Volume I This report presents the first national survey of miners' attitudes and opinions about their-work. The goal is to present attitudinal data that bears on coal production. Interviews were conducted in 26 mines with 2,000 miners. High levels of cooperation were exhibited by management, union and the employees. Data are presented about miners' attitudes about general aspects of their work such as pay, supervision, their jobs, etc. Another section of this report reviews opinions about specific aspects of work performance. Recommendations are presented.

Jan 1, 1985

By William E. Young

There are many large rhodonite-bearing veins containing manganese in the Eureka-Animas Forks area of the San Juan Mountains in Colorado. The Sunnyside vein is the largest known vein in the area. As observed on the surface, the vein is mineralized over 8,000 feet and attains a maximum width of 200 feet. The average width of the vein and its branches and ramifications is 58 feet in the area that was mapped in detail. The weighted-average analysis of surface and underground samples from the northeastern extension of the Sunnyside vein is 8 percent manganese. Most other known veins in the area have a similar manganese content. The Hidden Treasure vein lies southeast of the Sunnyside-No Name-Mastadon vein. The weighted average of the analyses of surface and underground samples from this vein is 13 percent manganese. Exposures of the Scotia-Silver Chord vein are visible over a strike length of 4,000 feet on Treasure Mountain. Diamond-drill holes show that the vein contains 10 percent or more manganese to a depth of 400 feet. The vein has an average width of 28 feet. The Independence vein is exposed on the surface for a distance of 600 feet and has an average width of 6 feet. Three cut samples taken across the vein had an average content of 20.7 percent manganese. Sampling of the outcrops of eight veins in the Placer Gulch area also indicates manganese. Numerous other veins cropping out in the surrounding area are similar to the outcrop of the Sunnyside vein system mineralogically and are worth investigating.

Jan 1, 1966

By Charles E. Whieldon

The importance of producing more oil from known petroleum reserves has placed increased emphasis on the application of secondary-recovery methods. Recently published reports3 4/ describe the results of waterflooding in Roane and Pleasants Counties, W. Va. (see fig. 1.) This report describes the Barron Kidd Oil Co.?s Santee waterflood project, Maxton sand, Burton field, Church district, Wetzel County, W. Va. (See fig. 2.) The Federal Bureau of Mines hopes that these reports will stimulate interest in improved waterflooding techniques, thereby discouraging premature abandonment of oil leases.

Jan 1, 1961

By Charles H. Simmons

Two versions of a VF transceiver to aid in location of trapped miners has been developed and tested. The belt worn model was produced in both transmitter and transceiver configurations. In addition, a quantity of the belt worn models were fabricated using aluminum wire instead of copper in order to reduce unit weight. Ten prototypes of a battery cap model VF transceiver were also fabricated demonstrating further unit size and weight reduction while maintaining electrical performance. Samples of- both versions were tested environmentally and the test data is included in this report. While both versions of the VF transceiver are similar electrically, and are constructed using convential manufacturing techniques, the battery cap model realizes a lower total weight, smaller volume and production cost than the belt worn version. Operationally, the battery cap model assures that the VF transceiver will always be with the miner.

Jan 1, 1981

By Hon-Yim Ko

The properties of coal from the Pittsburgh seam, procured from the Bruceton and Federal No. 2 Mines were found to be similar. Strength and stiffness properties of Beehive Mine coal were determined and the material found to be isotropic. Mechanical, index and geologic properties of roof and floor coal measure rocks from Beehive mines were measured and correlated. Analytic formulations are given for coal creep under uniaxial loading, while triaxial creep is being investigated. Results of testing of coal model structures are compared with predictions from using several material models.

Jan 1, 1976

By M. G. Wallis

This report presents the results of a study to develop a detailed mining method design based on longwall mining with sublevel caving. The method is applicable to low-dipping coal seams 20 or more feet thick such as are found in the western United States. The report covers (1) the development and description of the mining method, (2) evaluation of the engineering feasibility of the design, (3) estimates of productivity and recovery, and (4) an engineering cost analysis and economic feasibility evaluation of the mining method design.

Jan 1, 1977

By Kim B. Shedd

An initial evaluation of the flow of cobalt-containing materials in the United States was prepared. The following aspects of materials flow were included: cobalt released as a result of mining and processing other metals and minerals; scrap generation and subsequent recycling or cobalt recovery; and cobalt losses resulting from the generation of wastes, dissipative uses, and disposal of used products. Where possible, estimates were made to quantify the amount of cobalt lost from the materials flow. More than 2,000 metric tons (mt) of cobalt are released annually from mining and mineral processing in the United States, including 480 mt of cobalt in coal produced in the United States. Metallurgical industries examined in this study have well-established recycling or cobalt recovery practices. The petroleum industry recycles spent catalysts, and some chemical catalysts are also recycled. Losses generated during cobalt chemical and powder processing were estimated at 50 to 80 mt of cobalt annually. Losses from alloy processing and the manufacture of parts and products were estimated to be 360 mt. These industrial losses are greatly outweighed by an estimated 2,780 mt of cobalt' consumed in the United States each year to make products that will ultimately be disposed of.

Jan 1, 1992

By C. H. Herty

As the problem of inclusions in steel has become increasingly important, more and more attention has been paid to the source of the oxide inclusions in steel. In killed steels the oxide inclusions are traceable to the reaction of deoxidizers with the iron oxide dissolved in the steel during the refining period of the open-hearth heat. In a large class of steel known as "rimming steel" the action of the steel during solidification depends entirely on the gas evolved, and this evolution in turn is controlled by the amount of iron oxide in the liquid steel in the mold. It is therefore of great importance to be able to determine the amount of iron oxide dissolved in steel and to devise methods for the control of iron oxide in any class of steel. The object of the present investigation was to obtain a true value of the oxygen content of liquid steel. If the steel has not been deoxidized, the greater percentage of the oxygen is present as iron oxide in solution.

Jan 1, 1932

By William C. Hood

A leaching column technique that produces effluent similar in quality to coal mine drainage in the Eastern Interior Basin has been developed. The columns are charged with 1000 grams of crushed overburden and cycled through the leaching process once a week for twelve weeks. Inter-relationships among the important chemical constituents are very similar to those present in actual mine drainage waters, but the overall concentrations of ion are more dilute in the leachates. Multiplying the leachate concentrations by a factor of 4.5 gives values similar to mine waters. Available data suggests that each of the leaching cycles represents about three years of natural weathering, so that the leaching technique can predict the evolution of the mire drainage water over a time span of nearly 40 years. Use of the leaching technique with drill core samples should provide a method of approximating mine drainage quality in advance of mining and should be quite useful in identifying potentially toxic units in the overburden. However, the results should he considered to be a 'worst case' situation because the technique' does not consider the effects of reclamation.

Jan 1, 1984

By R. C. Annear

This report describes open, sublevel, and shrinkage stoping at the Greenwood mine, operated by Inland Steel-Co. The iron ore mine is in Marquette County, Mich., about 6 miles southwest of Ishpeming (fig. 1). The Greenwood is one of three active underground hard-ore mines on the Marquette range, the others being the Cliffs-Shaft and the Champion mines. The operation reflects an achievement in exploiting small, difficult-to-mine hard-ore bodies lying beneath a 200-foot overburden of glacial drift, which is partly water bearing. This report can indicate only briefly the efforts of personnel in overcoming adverse conditions in mining more than 2 million tons of ore, 80 percent of which was in lump form, for open-hearth production of steel. Significant data presented include descriptions of the principal mining methods employed, sublevel and shrinkage stoping; percent aged mining costs for the entire year 1957, covering both direct mining costs and general expenses; and performance records in units of labor, power, and supplies.

Jan 1, 1960

By Loren R. Anderson

This is an Appendix of Volume I. In contains the results of the electric cone penetrometer soundings from the second phase of the testing program.

Jan 1, 1982

By Michael Rieber

An analysis of coal slurry pipelines was presented in our May 1976 study, Route Specific Cost Comparisons: Unit Trains, Coal Slurry Pipelines and Extra High Voltage Transmission (4]. The present study extends that analysis. The earlier work included technical and economic cost descriptions of the black Mesa and ETSI pipelines as well as some hypothetical pipeline routes. Water problems, safety and environment, required resources, and labor impacts were discussed at some length. Additionally, pipeline impacts on competing railroads, slurry-rail comparisons, and cost escalation. were analyzed. The difference in pipeline profitability to an owner-operator versus a promoter-builder was suggested. These aspects are not redone in this study. Here, we present a synopsis of the previous results and a general statement of coal slurry pipelines. Extensions of the arguments are presented where they appear warranted. New material is developed in the area of pipeline branching and tapping. This would appear necessary if slurry pipelines are to function as more than private lines; if they are, for example, to be responsive to common carrier requirements.

Jan 1, 1977

By J. A. Herbst

During the last decade it has been established that conventional flotation control strategies based on classical control theory result in significant increases in grade, recovery, and operating-cost savings. In the current report a description of an advanced model-based control philosophy is presented. The derivation and verification of a simplified flotation model is described. The implementation of a Kalman filter for estimation of unmeasured variables for input to controllers is discussed. Several control strategies using the model-based approach are described, emphasizing the nonlinear nature of the flotation plant. Expected trends in the implementation of such model-based flotation control strategies in the future are discussed.

Jan 1, 1986

By Peter de Bakker

The objective of this contract was to develop a simple, reliable, economical, remote-control roof bolting module for installation of mechanical and resin bolts. It was to be capable of placing longer than seam height bolts, up to 10 ft lengths, from a seam height of 36 to 72 in., while keeping the operator under supported roof. The resulting machine, called REM-Bolter, is a low profile unit that utilizes Foster-Miller Flexible Shaft Roof Drill, a Bendix Roof Bolt Inserter and a newly designed. Roof Bolt Lifter/Torquer. Every effort was made to strike a compromise between complete automation and complete manual control. In a controlled laboratory environment the REM-Bolter remotely installed 1000 bolts. Subsequently the machine was tested in an operating coal mine where 500 holes were drilled (and an equal number of bolts were installed) remotely, over a 4 month period. The results of all tests Live shown that the operator of a machine of this kind can quickly, and repeatedly, install rootbolts remotely from his operator compartment some 8 ft away from the drilling/bolting action. The report includes recommendations for improvements to the present REM-Bolter design that would translate the present test bed into a second generation test bed and a potential first generation production unit.

Jan 1, 1983

By Patricia R. Devine

This appendix documents the mathematical approach to deriving the components of change presented in this report. The formulation closely follows that contained in Chapter IV of the documentation for the BEA 1977 Input-Output Tables.' The basic elements for the calculations include the "use" matrix (U), the "make" matrix (M), and any of the ten columns of final demand (generically represented by the symbol y). The use matrix contains information about changes in the technological processes of production, while the make matrix describes the nature of secondary product production in each industry. We adhere to BEA conventions in maintaining careful distinctions between commodity output (c) and industry output (x). The industry-by-industry 1-0 tables supplied by NYU for use in this analysis are square matrices, with the number of commodities and the number of industries both equal to 85. The BLS table for 1982 (commodity by industry) was aggregated and adjusted to be consistent with the earlier tables. The three basic steps for estimating components of change proceed as follows for each column of final demand. 1) Calculate the actual change in output of each commodity for each of the four time periods: 1963-72, 1972-77, 1977-82, and 1963-82.

Jan 1, 1988

By W. J. Kroll

This report is concerned with the many sidelines that were investigated incidental to developing a process to produce ductile Zirconium by members of the staff of the Bureau of Mines laboratory, Albany, Oreg. The results of the main investigation, concerning the production of malleable zirconium by reduction of chloride with fused magnesium under helium, have been described in previous publications. These should be taken as a background to facilitate understanding of this work. Literature on the metallurgy of zirconium has been summarized in a separate publication (2), and references are given in this report only when new publications have to be considered or old ones stressed. Most of the observations described in this report can be applied to the problems involved in making titanium with virtually no change. In general, titanium is easier to reduce than zirconium, since its affinities are lower. Also, its chloride is easier to handle and keep clean because it is a liquid at room temperature.

Jan 1, 1952

By William A. Hustrulid

An overall summary and the individual reports of eight workshops to determine research and development needs in western mining ore presented. Problem areas are identified, and recommendations regarding priorities, funding sources, and prime movers are made. The objective of this contract was to identify research and development needs for advancing mining technology as well as health and safety measures for western U.S. Surface and underground mining. This was accomplished by convening a series of workshops where problems could be thrashed out by producers of trona, uranium, open pit copper, underground salt (from the Midwest and New York), underground metal and nonmetal, etc. In addition to problems, future priorities, funding, and the desicion as to who should be the prime mover on R & D were discussed.

Jan 1, 1976

By Bryan R. Carmenati

This report documents the need for formal health and safety, and equipment operations training in the mine construction industry. The outlines, objectives, and training texts were developed based on the recommendation of needs of mine construction personnel, and those of Dames and Moore (Safety Analysis of Shaft Sinking operations, 1977) and Kinton, Inc. (A Training Program for Conventional and Raise Drill Construction Personnel; Phase I, 1979). The training material samples contained herein (and under separate cover in its entirety) are designed to improve the safety and production of those in mine construction. An instructor-directed presentation is recommended. The results of the study are presented in the Findings and Recommendations section of this report.

Jan 1, 1982