Search Documents

By D. S. Scovira, T. Gustavsson

Exiting WW2 (mid-1940s), the potential of nitrates (ammonium nitrate, calcium nitrate, sodium nitrate) and hydrogen peroxide for application as a commercial explosives for mining, construction, and other industrial purposes both became known. The technology stream advanced the development and uptake of nitrate based explosives to the point that they are the current global standard for blasting. Today, environmental issues are shaping the strategic agenda across various industries. Most global mineral resource, construction houses, and explosive manufacturers have publicly announced ESG carbon reduction commitments in support of COP26 Net Zero 2050. The mid-2010s saw a renewed interest in hydrogen peroxide explosives to eliminate NOx fume. Carbon reduction initiatives in the early 2020s provided additional impetus to investigate hydrogen peroxide based explosives for industrial use. Hypex Bio has recently pioneered the formulation, manufacture, and end-use delivery of a Hydrogen Peroxide Emulsion (HPE) on an industrial scale. The HPE is composed primarily of hydrogen peroxide (H2O2) plus a lesser amount of fuel and emulsifier phase. The base HPE is produced in a low energy intensity modular plant using industry proven mixing techniques. The base HPE is a white, highly viscous emulsion that is similar in consistency to base nitrate emulsions. To enable end blasting use, a mobile charging unit gases the base HPE to a detonable density. The HPE is compatible with current priming and initiation systems. Hydrogen peroxide explosives offer a significant reduction in total carbon emission as compared to nitrate based explosives. The production of ammonium nitrate (AN) emulsion is energy-intensive and not carbon neutral. Based on the EU Average and for the oxidizer phase only, 1 kg [2.2 lb] of AN emulsion emits 2.3 kg [5.1 lb] of CO2 as compared to the production of hydrogen peroxide emulsion that results in 0.23 kg [0.5 lb] of CO2. This is a difference of 90%. HPE contains no nitrates and does not generate post blast nitrous oxides (NOx). HPE generates no aqueous nitrate or ammonia pollution and is a solution to meeting increasingly regulated mine site water discharge limits. Hypex Bio recently conducted a successful underground HPE evaluation with a major mining company in Sweden. HPE blast designs were the same as those done with nitrate based emulsions. Rock breakage, advance, muck displacement, and excavator performance were equivalent. Ventilation and re-entry times were reduced. The mining company has expressed further interest in assessing HPE and is demonstrating industrial leadership by exploring this transformative explosive technology

Jan 1, 2024

By John Hutchings

Drilling and blasting is a clearly delineated work process, which has well defined inputs and outputs. Drilling and blasting is also a process with a number of steps each of which has measurable outcomes. Drilling and blasting is ideally suited to the application of Total Quality Management principles. Most drilling and blasting information is generally poorly managed with disjointed and unrelated Information Technology systems managing parts drilling and blasting data. Data is often moved from on system to another, sometimes manually. In the field, drilling and blasting is still very much a paper based system and which has not generally benefited from some of the recent hardware and software technology advancements now “on the shelf”. Data collected on paper rarely is transcribed back into an electronic system for further analysis. It is often difficult to collate or review historic drilling and blasting data. This paper will present a definition of Total Quality Management and demonstrate how it can be applied to the drilling and blasting work process. Total Quality Management defines the mechanisms for the application of continuous improvement to drilling and blasting. Continuous improvement will provide opportunities to modify drilling and blasting work process outcomes and generate real cost benefits within the overall mining process. A complete drilling and blasting management system frame work, called DBS, is presented in this paper. DBS provides all the components necessary to implement a full drilling and blasting Total Quality Management solution. Also highlighted will be appropriate “off the shelf” technology that can be applied to replace current paper based systems and provide the means to connect with other mine data systems. Various examples will be discussed which will demonstrate potential benefits of applying a structured Total Quality Management approach to a drilling and blasting work process.

Jan 1, 2004

By George E. McCormack

At the time of my visit to the Peoples Republic of China I was employed by the E.I. DuPont Company as a Technical Specialist in the Explosives Department. The purpose of my visit was to observe the use of explosives in mining and tunneling in a coal field 500 miles south of Peking near Hsu Chou in Kiang Su Province. The DuPont Company was preparing a proposal for the sale of a Tovex water gel plant to the Chinese Government.

Jan 1, 1982

Drilling through unconsolidated material I need to drill blastholes through a mix of consolidated and unconsolidated material. This material is hung up in an underground ore pass. The total length of the holes would be approximately 200 feet. We have attempted to drill through the material with conventional ITH drilling, but were unsuccessful. Does anyone have a suggestion? I am more than willing to bring in a contractor to do the job, if they have solid experience with this type of problem.

Jan 1, 2011

By David Hersey

The Paseo Bridge was located at the I-29/I-35/US-71 Missouri River Highway Crossing. It was built between 1952 and 1954 by Massman Construction Company. The 1,232 foot long, self-anchored suspension bridge was the longest of its type when built. On Jan. 22, 2003, a connector pin designed to allow the bridge to expand and contract during temperature cycles seized and caused a portion of the bridge deck to raise up and block traffic. This marked the beginning of the end for the old Paseo Bridge.

Jan 1, 2013

By Paulo Couceiro, Manuel Lopez Cano, Carlos Rodgriguez Calvo

Apart from its difficult execution, underwater blasting is one of the most critical operations of the blasting techniques; mainly because of the ground vibrations - normally associated with low frequencies -, destructive hydraulic shock waves, the difficult coordination, and high costs. To solve these challenges during the underwater blasting on the expansion program for the Panama Canal “Widening and Deepening of the Pacific Entrance and the South approach Channel to the Third set of Locks of the Panama Canal”, a new method to blast using bulk explosive, developed by MAXAM, was used. The project was successfully executed, and more than 800.000m3 were blasted in less than 5 months, jointly with the biggest underwater drilling platform ever build, the Yuan Dong 007, with ten hydraulic drills on board guaranteeing a high production, excellent fragmentation result, total control of the vibration levels, no complain of the neighborhood surrounding the area of the project and simple local logistic due to the classification of the main product used (an oxidizer classified as 5.1). That was finally sensitized down in the hole.

Jan 1, 2011

By K. M. Kim, J. B. Kemeny

A case study was conducted with 5 shots with varying pre-blast block sizes and explosive energies. From this case study a site-specific predictive fragmentation model was developed. There are two main innovations in this study. One is using an image analysis program (Split-Desktop 3.0) on the bench face to obtain the pre-blast block size (F80) quickly and consistently. Another innovation is to utilize the Schmidt Hammer Hardness (SHH) to estimate intact rock strength.

Jan 1, 2011

By Milos Bila

The second half of 2008 and the first half of 2009 brought up important anniversaries. My old passport from Czechoslovakia has a stamp with date 10-10-1968 at 10:00 AM, the exact time I crossed the border between the former Czechoslovak Republic and Austria. This date has an important meaning because I could not come back to my country for the next 21 years. The 40th anniversary of Soviet led invasion, which took place on the 21st of August 2008, revealed some unknown and long time kept secret news.

Jan 1, 2010

By Rachel Bauer, Jacob Henderson, Dr. Catherine Johnson

Capital Quarries in Owensville, Missouri faces several challenges when designing a blast that allows for ease of movement while maintaining controlled throw and compliant air over pressure. The primary challenge is the nearest non-owned structure (NNOS) is a residential home located 250 feet from the quarry. Another challenge is a production bench which is 100 feet tall and separated from the NNOS by Pennsylvanian fire clay that filters out high frequency waves from the blast. Material from the blast must also be less than 5 inches in order to be processed by the crusher in the quarry. To provide as much relief as possible, production shots will consist of a single row with the minimum required burden. To design the shot, signature hole analysis was used to determine the optimal timing between powder columns. Electronic detonators provided an accurately timed shot to minimize the amplitude of the vibrations while maximizing the frequencies. Boretraking and 3D profiling with Renishaw laser profiler and Strayos drone photogrammetry provided an accurate burden measurement. Powder factor was kept at 1.3 tons/lb using bulk emulsion. The boreholes were split into 5 powder columns with the top of the hole firing first in order to blast to floor grade. The resulting shot produced good fragmentation and shot to floor grade. Seismograph readings showed air over pressure vibrations within legal limits. Due to this success, multiple shots will be designed using the process described.

Feb 6, 2023

By Anders Lagerkvist, Agne Rustan, Tommy Edeskar

Landfills containing house hold waste produces methane gas during its decomposition. This gas can be recovered and used for heating purposes or as fuel for vehicles. Gas drainage pipes are installed in the landfill and connected to a central suction point. Methane gas is produced over several years until the slots in the drainage pipes are clogged by black mud. And the bottom of the vertical drainage pipe are filled with mud and water. The hypothesis tested in this paper is if blasting in the drainage pipes could activate the production and flow of methane. In the first part of the paper we have studied what maximum linear charge concentration could be used in different size of PE-pipes place vertical on surface and surrounded by air. The results show that the maximum linear charge concentration for single blasts varied between 5-10 g/m, depending on the diameter of the pipe (90, 100 and 160 mm). Maximum charge concentration for the repeated blast varied between 2-5 g/m. In the second part of the paper we study what maximum linear charge concentration could be used in situ for full scale blasting tests in a special prepared test area which later on was dug out after the blastings. Up to 40 g/m could be used without damaging the top of the 160 mm diameter pipes. The increase in methane flow was so low so it could not be measured c4.5 m3/h. The conclusion therefore is that the stimulation of methane flow by explosives is not enough.

Jan 1, 2000

By Joshua Hofman, Braden Lusk, Erin Morris

Explosions in urban environments, whether of accidental or malicious cause, often result in extensive injuries, loss of life, and property damage. The ability to predict the damage inflicted by these events is highly sought after; in order to predict damage, the behavior of blast waves within these environments must be quantified and understood. Urban constructs such as buildings and roadway intersections affect the natural propagation of a blast wave, intensifying or rarefying the wave depending on their arrangement.

Jan 1, 2012

By Zhang Yangde

"This paper reports the clinical research work of Micro-explosion of Biliary Calculi . In theprogram the technique of directional micro explosion applied to disintegrate the biliarycalculi of body and decreases the rate of operation. Up to the present, 235 cases of biliaryduct calculi have been successfully treated by use of implusive force of micro-explosion .The success rate of blasting stones was 100% by the use of the directionalmicro-explosive instrument made by us , the once success ratio of micro-explosion was93.2% and tl~o rmulb of treatment were satisfactory. . Considering the density of theblood vesselsiD the human liver, limitation of space in the h~patic.ducb, the securiey andadaptation, we have designed two types of micro- explosives equipment called ZS device,electric initiation and nonelectric initiation to initiate explosion. The head diameter of thedevice ie 1.5-1.8 mm . It is applicable to all kinds of fiber endoscope by inserting ZSdevice under grossing eyes or TV set ."

Jan 1, 1993

By Jaak J. K Daemen, Clayton R. Morlock

A study was performed to evaluate the predictability of airblast overpressures induces by production mine blasting. Thirty-seven production blasts were monitored using 3 blasting seismographs giving over 100 blast overpressure records. Blasts were monitored at 5 coal highwall operations and at a limestone quarry, all in the midwest. Blasts consisting of small surface charges were monitored to permit an assessment of prediction methods under controlled conditions, as well as to observe actual delay intervals and their influence on the overpressure.

Jan 1, 1983

By Enrique Munaretti, Vitor Rosenhaim, Jair Carlos Koppe, Joao Francisco Feijo

The B3 mine is a multiple coal seam strip mining in operation in Rio Grande do Sul, the southernmost state in Brazil. A traditional truck & excavator operation is used to remove the overburden and selectively mine coal seams, ranging in thickness from 30 cm (1 ft) to 2.5 m (8.2 ft). Blasting is required in order to excavate part of the sedimentary rock overburden where the rock is too hard for mechanical excavation, and to mine the coal seams, selectively.

Jan 1, 2012

By BernardThierry

To be able to precisely predict the result of a mine blast before pressing the button is a goal for many blasters due to the environmental and economic constraints of our century. Based on the fundamental fracturing of the mechanism of rocks by explosives, the most recent research in digital modeling, the power of present computers, and the possibilities offered by drones, we have designed a realistic digital 3D simulation model for mine blasts. This new type of model enables us to concurrently simulate the fragmentation of the rock, its movement and the associated seismic levels, all within a few minutes, which is a time compatible with a production cycle. Due to the complexity of the model, this article reveals the main principles and compares the results of simulations with on-site measurements in various sectors, i.e. quarries, mines and tunnels.

By Matheson and Miller

Does anyone have any definitive information on vibration limits for damage to well casings near blasting? Also, are people using self-imposed limits when approaching cased wells? I can only tell you what I have personally done with success. Often in new construction in hard rock, the well is drilled before the foundation is excavated and before the ditch for the water line is excavated. These both require drilling and blasting. Under these circumstances when blasting for the ditch for the waterline we will drill right up to within 10 inches (not feet) of the well casing. We drill line holes the width of the ditch, then about a foot from this, another row of trim holes then as we move away from the casing holes for 1 1/4 inch stick powder for about three rows then as we get further still, we can load with ANFO. I do not have vibration data for this but my experience has been that as long as you are not displacing the material into the casing that no damage is done. These typically are steel casings for residential water service.

Jan 1, 2010

By Frank Sames, Brad Terhune

In many construction projects and in most quarrying operations drilling and blasting remains the only feasible method of loosening rock in the removal of rock or overburden, the development of the quarry and in the production process of crushed stone. Often, a blasting plan is required for the project or the quarry’s permit with primary concerns over safety and site security, and compliance with environmental regulations or standards. From this plan, a blasting program has to be developed considering the varying requirements of production, the advance of the mineral extraction and the environmental impact. The actual blast design requires a planning and optimization process. This optimization process is driven by the blasting technicians/engineers, project or mine management and often by community concerns. The blast design process comprises the selection of blast parameters, including the explosives, and the actual layout of the blast. Design tools and controls range from conventional methods based on established blasting practices to advanced design tools or computer models. Blast monitoring and evaluation can also range from empirical to advanced blast assessment. The data and information from each blast or a series of blasts can further be used in the optimization process. Its success depends upon recording the data, the timely transformation of the data to relevant information, and the development of process oriented knowledge. The elements of the blast design process are summarized and described with examples of state-of-the art engineering controls. The reporting and monitoring of individual blasts is discussed with respect to data management and information systems. A conceptual overview of the components and interfaces of a blasting program is given and discussed on the background of technical, management and community concerns.

Jan 1, 2004

By Shao Li, Chen Zhiming, Wu Jihong

In this paper,powder emulsion explosives,which have high sensitivity and strong detonation force,have been studied by applying emulsion technology to the production of the present powder ones.Under the condition of #8 industrial detonator initiation,the distance of air gap propagation is 110~180mm,brisance !3.5mm, lead block test value 325ml and detonation velocity 3000~4000m/s for small diameter (35mm) explosive cartridges.In addition to these,the factors effect on are investigated by experimental study and theoretical analysis.

Jan 1, 1991

By Natalie Zeleznik, Brian Hawkins, David Bradley, Rachel Gooding, Patrick Wilson, Brian Somes

"To perform a probabilistic risk assessment (PRA), a method of quantifying the risks associated withinfrequent, high consequence events, consequence models that generate representative estimates of human health consequences for a wide variety of representative scenarios are commonly used. Criteria that suitable models must possess include: (1) input requirements necessary to generate large volumes ofprobabilistic simulations; (2) the capability to output injuries with the necessary details and resolution;(3) the ability to capture the variety of different scenarios inherent in an assessment; (4) acceptablecomputational requirements; and (5) sufficient stakeholder buy-in for community acceptance."

Jan 1, 2017

By Jeffrey A. Straw, Joseph P. Jr Shinko

Ground vibration produced by blasting operations within South Florida, due to saturated soil conditions, generates surface vibration waves that may be measurable over distances of 3 - 5 miles from the source, and perceptible at distances of up to 2 miles. Structures above ground usually receive the most of the attention from the effects of high vibration levels. During construction of the Trilogy Development of the Swerdlow Companies, blasting was completed in a lake excavation immediately adjacent to the City of Pembroke Pines Utility Department, Deep Injection Wells No. 1 and No. 2.

Jan 1, 1994