Search Documents

By J J. Mullay, G W. Anderson, C J. McFinley, J F. VanNorman, C J. Kefer

Previous work has shown that testing of precompression effects conducted on a small scale under simulated field conditions in actual rock provides a reasonable model for the evaluation of explosives and initiators under the adverse conditions encountered in production blasting. Using this methodology can result in greater understanding of the phenomena as well as the ability to predict performance. This effort has been extended to evaluate various parameters not previously studied in a controlled fashion. The present paper describes the use of this technique to study the effects of delay timing on precompression effects. Intervals from 25 to 150 milliseconds are included in the study. Both VOD measurements and damage estimates are utilized in the evaluation. The results demonstrate that timing delay between holes is quite important in determining the overall effectiveness of a blasting program.

Jan 1, 1994

By Kunihisa Katsuyama, Yuji Ogata, Takuya Taguchi, Toshinori Arikiri, Yuji Wada, Kiyoshi Hashizume

The impact sensitivity of hot emulsion matrices was examined to investigate the safety assessment in the emulsifying equipment which forms the emulsion matrix in a water-in-oil type emulsion explosive. The sensitivity could not be evaluated by the small fallhammer test device commonly used in Japan. Therefore, a large fallhammer test device was used. It was confirmed that an explosion, a decomposition, or a no-reaction took place according to the degree of the impact. When a decomposition took place in the hot emulsion matrix, the behavior of it was investigated further by a DDT test. It was found that a decomposition, or a no-reaction occurred according to the degree of confinement.

Jan 1, 1997

By D Linn Coursen

Detonation propagates in the subject blasting agent at about 2.7 km/sec when it is heavily primed but explosion propagates in it at only about 0.43 km/sec when it is lightly primed. When propagating at 0.43 km/sec, it produces a borehole pressure that is slightly less than 1 kb, but no yellow fumes or other sign of incomplete reaction. It is a pumped AN/emulsion blend to which additional water is added by circumferential injection at the inlet of the hose through which it is pumped.

Jan 1, 1994

By Frank Barker

Mining operations present a very different environment to the suppliers of explosives, initiating systems and services, both on surface and underground. Typical hazards include underground movement, air quality, ground stability, moving equipment, and the use of explosives. As contractors to the mining industry we do not have management control over the environment in which our people operate. The hazards and consequent level of risk that our people are exposed to in some mining operations are significantly higher by orders of magnitude than in a normal factory environment. Orica Explosives (and other Explosives suppliers) are continually and increasingly identifying opportunities to partner with customers by adding value through the provision of services leading to a reduction in total mining costs. These services include the provision of a bulk underground loading services, delivery of product into underground magazines, magazine management, value added blasting, conversions, rock-on-ground contracts, and blast management programs.

Jan 1, 2000

By D Linn Coursen

In the proposed method, the charges are elongated and arranged in one or more arrays. The orientation of each charge in an array, its velocity of propagation of explosion, and the velocity of propagation of vibration in the formation are such that, at an outlying location where vibration is to be reduced, the onset of vibration from explosion of the first negligibly small increment of each charge arrives a finite time before that from explosion of the last negligibly small increment of that charge. The charges of each array are fired in accurately-timed sequence, with the times between initiations chosen so that, at the outlying location, the onset of vibration from explosion of the last small increment of each charge, except the last charge, arrives a negligibly small increment of time before the onset of vibration from explosion of the first negligibly small increment of the succeeding charge. With such timing, vibration may be reduced at the widest range of locations by tilting the boreholes so that the terminal end of each charge is directly above or below the terminal end of the succeeding charge.

Jan 1, 1995

By P D. Katsabanis, L Liu

Numerical modelling of fragmentation and throw is used to provide information on practical blast design parameters. The function of airdecking and its practical implications, the importance of the initiation point and aspect ratio of cratering charges and the timing between adjacent blastholes are investigated. Accuracy requirements for detonators are discussed with emphasis placed on the volume and fragmentation of the blasted rock, and compared to experimental results. Practical guidelines which have been based on intuition are examined using the model. Some of the predictions have been tested and correlate well with experimental results, obtained in the laboratory. Findings show that a minimum airdeck length is needed to realize any benefit from the application of airdecking in production blasting while the process can enhance the shock energy provided by non-ideal explosives significantly, bottom initiation of charges is beneficial to fragmentation and the aspect ratio for cratering charges can exceed the traditionally accepted ratio of 6. Regarding timing, in the ease of cratering charges, true simultaneous initiation shows beneficial results for the volume of blasted rock; however the accuracy required for practical detonators is very high. Fragmentation improves after a certain delay time while the optimum can be achieved at a range of delays. Timing affects muckpile shape; however it appears that subtle differences in delay times do not have a significant effect.

Jan 1, 1997

By Robert A. Cortese, Lon D. Santis

This paper describes a method of measuring continuous detonation rates using standard electronic parts, coaxial cable, and a data recorder such as an oscilloscope. Three six-volt lantern batteries or a DC supply power the electronics that cost less than $100. Included are means of showing low battery power, finding the proper voltage scale on the recorder, and test triggering of the recorder. Modifications of the circuit allow for use in the field to measure charges up to 57 meters and for use in the laboratory to measure short charges. The high resistance (8.709 Ohms/meter) coaxial cable is a mass produced, special order cable available commercially. The driver circuit delivers a constant current to the cable, and as the detonation shorts the cable, a change in circuit voltage occurs. Recording this voltage change over time allows determination of detonation rate resolute to the sampling speed of the recorder. An oscilloscope or personal computer with a data acquisition card can easily record the data for analysis. Detonation rates recorded in the laboratory using the coaxial cable and the Bureau of Mines's traditional probes are presented. The system accurately measured the detonation rates of ANFO confined in steel pipe, detonating cord, and unconfined high explosive.

Jan 1, 1996

By Lon Santis, David Leidel, John Tatom, Meredith Hardwick

This paper describes the development and methodology of the Institute of Makers of Explosives’ Safety Analysis for Risk (IMESAFR), a risk analysis software program for commercial explosives operations. IME is a nonprofit safety and security association devoted to the safe and secure manufacture, transportation, storage, and use or disposal of commercial explosives in the US and Canada since 1913. The software methodology’s basis is the U.S. Department of Defense Risk Based Explosives Safety Criteria Team’s Safety Assessment for Explosives Risk (SAFER) software. A diverse group of industry and government experts contributed to modifications to SAFER that reflect commercial operations. IMESAFR is intended to supplement the American Table of Distances (ATD) and offer standardized methods of managing risk from a wide variety of commercial explosives operations where the ATD does not apply. The modifications made to SAFER primarily involved the addition of commercial activities and potential explosives sites (PES). A review of commercial explosives accidents and operations over the last 20 years served as the basis for establishing probability of event values. An industry survey of commercial PES types in the U.S. and Canada was conducted to identify and address critical differences in commercial structures as compared to the military structures in SAFER. The paper concludes with discussion of the potential uses for quantitative risk analysis (QRA) and a description of other explosion effects software

Jan 1, 2007

By Robert C. Fouchard, Gordon Chalmers, David E. G. Jones, Ivana Alilovic, Phillip D. Lightfoot

There have been numerous international instances over the last several years in which pumping emulsion explosives has resulted in accidents, apparently as a result of increased thermal sensitivity under these conditions. The key questions for the explosive industry are (1) what are the parameters that influence the sensitivity of emulsion explosives and, (2) how do these various parameters interact. To address the sensitivity of emulsion explosives to various parameters, a study was undertaken using an accelerating rate calorimeter (ARC) and a heat flux calorimeter (HFC). The effects ofthe addition of ammonium nitrate (AN) prills and different grades of aluminum (Al) on the thermal behaviour of emulsion explosives were determined. Additionally, changes in pressure, atmosphere (inert or oxidizing) and sample vessel material were assessed for their impact on thermal sensitivity. Addition of AN prills, fine granular Al or atomized Al did not affect the onset temperature for exothermic decomposition, so that the maximum “safe” temperatures for emulsions containing these additives will be similar. There were differences in the rates of self heating, however: AN prills decreased the rate of self heating, whereas atomized Al increased it. The emulsion formulations containing atomized Al produced small holes in titanium vessels. This phenomenon did not occur in Hastelloy C vessels, providing a reminder that materials of construction need to be carefully considered for equipment used to manufacture or handle emulsion explosives.. Both ARC and HFC experiments gave lower onset temperatures in air than in argon. We attribute this to oxidation of the oil phase by air. This result is significant for dry-running pumping conditions, where emulsion is heated in the presence of excess air.

Jan 1, 2000

By Michael Milstein

Northwest Research Station said as more and more older dams are removed to benefit fish, it’s become clearer that rivers rework themselves quickly.“Where the dam is relatively small, it’s a quick response,” he said. “The river quickly forgets.”

Jan 1, 2010

By Eduardo Gonzalez Fernandez, Jaime Rios Vazquez

This report substantiates the connection that always exists between explosives and vibrations and draws attention to low frequency vibrations, which are the moat dangerous for the structures affected.

Jan 1, 1986

By Stanley L. Lippincott

A number of Federal and State agencies require formal training for blasters. Federal agencies often specify the need for initial training involving all job responsibilities as well as periodic refresher training to assure adherence to current operating procedures. failure to provide and document such training can result in substantial penalties.

Jan 1, 1995

By Rob Farnfield

The control of vibration from surface mine blasting by the application of detonator (cap) delay techniques has been universally accepted for many years. For almost as long it has been known that, for delay techniques to be effective, a minimum of 8 milliseconds delay must exist between blast holes.

Jan 1, 1999

By Dale S. Preece, Steven Knudsen

A discrete element computer program, DMC (Distinct Motion Code) was developed to simulate blast-induced rock motion. To simplify the complex task of entering material and explosive design parameters as well as bench configuration, a full-featured graphical interface has been developed. DMC is currently executed on both Sun SPARCstation 2 and Sun SPARCstation 10 platforms and routinely used to model bench and crater blasting problems.

Jan 1, 1994

By Zhang Zhenyu, Wu Xinxia

The blasting quarrying technology of rock material of rock-fill dam is one of the more complex problems in the field of engineering blasting at present. The Kuz-Ram model is not suited to predict fragmentation distribution under the geology condition of Tianshengqiao(TSQ) fist-step power station. The modification of kuz-Ram model is discussed. With reference to the idea of model establishment of Kuz-Ram model and according to the results of experimental blasting in-situ, two fragmentation prediction models-TSQ-1 and TSQ-2 model are presented which are adapted to the particular condition of rock material querying blasting of rock-fill dam with concrete facing of TSQ first-step power station. The rapid judgment method of qualified grade material and the method of optimizing blasting parameters are also presented in this paper.

Jan 1, 1998

By Robert Hopler

Accidents associated with the storage of explosives prompted regulating the locations of such storage at least as early as 1719, when an act was passed in Great Britain. During the following years various refinements to the regulations were made, but a major explosion in 1864 in which there was destruction and loss of life as far away as 10 miles, led to the landmark Explosives Act of 1875. This act certainly had influence on regulators in the United States: when Massachusetts established an explosives distance/weight table in 1904 they referred to the prior British work. Later, Colonel Dunn of The American Railway Association convened a conference of explosives manufacturers to discuss safe storage. From this conference the American Table of Distances was established in December, 1910.

Jan 1, 2007

By Clarence Zink

The need for continual process improvement and innovation to reduce operating costs in the mining industry extends to the first significant encounter all production miners have with the rock: drilling blastholes. Material and design advances alone have greatly increased the productivity of today's tricone blasthole bit over bits used just a few years ago. Significant additional operating savings are being realized by utilizing improved air practices on blasthole drills, and by selecting drilling equipment designed to provide optimum air volume and pressure at the blasthole bit.

Jan 1, 1997

By Michael Weaver, Dale L. Ramsey

The Pinkerton Tunnel open cut project is part of the National Gateway Clearance Initiative improvement project to achieve a minimum of 21 feet of vertical clearance along CSX Transportation rail corridor so that double-stacked intermodal railcars can be transported between mid-Atlantic states and their ports to midwest markets in the U.S. This project involved drilling and blasting of 1.2 million bank cubic yards of rock over a 14 month period while maintaining rail traffic of two passenger and 38 freight trains daily. See story and photos, page 6.

Jan 1, 2015

By Lawson J. Taylor, Paul N. Worsey

Recent reputable evidence conclusively indicates that conventional chemical delay elements in delay detonators are notoriously inaccurate and can thus seriously affect blasting efficiency.

Jan 1, 1983

By K A. Broadhurst

Over the years International Standards have produced and are continuing to work on documents related to damage from blasting and human exposure to whole-body mechanical vibration and repeated shock.

Jan 1, 1988