Search Documents

By Ken C. Pruss

Seismic studies have proven that the frequency with which shock or vibration waves are reacting on a structure, in correlation with the amplitude of those waves, has a definite affect of structural damage. Different structures will react to different frequencies. In the past few years, some major coal producers in the midwest United States have shown that with the use of highly accurate detonators and exotic timing patterns they have effectively been able to adjust frequencies and this has enabled the operators to continue their excavation of overburden in environmentally sensitive areas.

Jan 1, 1989

By John W. Kopp

The U. S. Bureau of Mines investigated flyrock and burden movement from blasting at several limestone and basalt quarries in the upper midwest. Blasts have been studied at 14 different sites using high-speed cinematography. Blasting was accomplished in 75- and 150-mmdiameter holes using a variety of explosives. Films from each blast were analyzed to show burden velocities, observed flyrock distance, and direction of throw in relation to the shot layout. This technique, in some cases, allowed determining point of origin and cause of the flyrock as well as the flyrock range.

Jan 1, 1994

By Harnish Miller, Scott G. Giltner

One of the concerns with locating radioactive waste storage sites in salt deposits is how to permanently seal the underground storage areas once they have reached their storage capacity. The compaction of salt using explosives has been identified as a potential method of producing permanent seals in both entryways and shafts to storage areas. This paper describes the test procedure and results of a preliminary investigation to determine the feasibility of utilizing explosives in the compaction of salt. Three simple tests were carried out to measure the degree to which loose salt could be compacted.

Jan 1, 1996

By P D. Kasbanis, Lyall Workman

The energy output of an explosive is typically calculated using an equation of state and computer applications. Results are reported as weight and bulk strength, either in absolute terms or relative to ANFO. The effect of the equation of state selected and the assumptions regarding the energy calculation are considered and interpreted for the purpose of blast design. It appears that variations in the heat of detonation which result from the selection of the equation of state and parameters associated with it are not sufficient to significantly affect blast patterns, explosive consumption and costs. However variations stemming from the use of "available energy" associated with a cut-off pressure are significant, suggesting in many cases large pattern expansions. The validity of the various approaches is discussed and blast design results based on the energy calculated by the different approaches are presented and evaluated.

Jan 1, 1996

By Michael S. Wieland

The work-principle method was developed for theoretically resolving toxic fumes from non-ideal charge formulations. The whole description of a wanted process refers to macroscopic changes resulting from removing and imposing constraints that work one at a time to chronologically render trajectory terminal (key) states. The trajectory resolution utilizes a thermodynamic quasi-potential or negative work function, and numeric results require some appropriate standard thermodynamic (equilibrium) reaction code TDRC. The underlying method is unable to restrict reactions, tailor the work output or resolve states within the trajectory transitions, so the trajectory terminology is used somewhat figuratively. The work-principle model has the working fluid (reaction material) interacting with a tremendous reservoir (chamber air and walls), while forecasting the work performed upon a mechanical agent.

Jan 1, 1998

By Gregory S. Parker

The explosives community has seen tremendous technological advances during the past several decades. When this industry was in it's infancy and even past, Powder Monkey's defied the odds by relying on daring and cunning to unleash the power contained in nitroglycerin and black powder. Unlike the manufactured improvements, there has been little in professional evolution amongst the blasting fraternity unless provoked (for the most part) by the government. It is the intent of this author to advance the cause of an industry wide training and certification program, uniform in nature and broad-based enough to be voluntary, giving states whose outstanding programs are already in place, the opportunity to provide input. In creating this type of atmosphere, grandfathering, reciprocity and accessibility would be paramount. With ISEE taking a firm leadership role during the inception and NICET's involvement in the administration, the idea postulated here is intended to spark interest and debate, bringing the inception of such a program to the forefront.

Jan 1, 1995

By David A. Paul

Over the past several years a great deal of information on blasting vibrations and their effects on structures has been generated. Much of this knowledge has been gained through the use of ground vibration measuring equipment. While this type of information is valuable and gives us great insight into damage that can be incurred by structures from this source, very little, if any, information of this quality is available for the vast majority of cases in which an engineer is called upon to investigate alleged damage from ground vibrations. For the investigative engineer, then, the problem becomes one of accumulating whatever data is available and drawing a conclusion as to whether or not the subject structure was in fact damaged by the blasting vibrations. Such an analysis certainly requires a working knowledge of the literature on the subject and as much experience as he can bring to bear. Even thus armed, however, the data is often ambiguous, confusing, and/or contradictory. A practical approach is presented herein to aid the engineering investigator in arriving at the best possible conclusion available with the information at hand.

Jan 1, 1983

By William C. Burkle

In this paper, the author has cited essential areas in which the explosives engineer can assist the mine manager in his planning of an entirely new operation or in a major expansion of an existing facility.

Jan 1, 1990

By John Petty, John Loviza

Single sentence describing content-- "The best ally an Explosives Engineer can have in a court of law is a regulations enforcer stating all codes and standards were met on a jobsite".

Jan 1, 1996

By W Russell

This is an account of Cominco's explosives development work spanning 20 years from the introduction of ANFO into underground operations through to the present day where the use of blasting agents and sophisticated detonation systems create improved safety and blasting efficiency.

Jan 1, 1982

By James D. Cook, Dan McCutchen

Effective overburden casting requires the efficient use of todays explosives and initiations systems if a mine is to survive. This paper uses a major coal stripping operation as an example of the proper application of explosives and initiation system to their conditions.

Jan 1, 1994

By Gungor Tuncer, Ali Kahriman

"In bench blast design, not only the technical and economical aspects, such as block size, uniformityand cost, but also the elimination of environmental problems resulting from ground vibration and airblast should be taken into consideration."

Jan 1, 1999

By Miles Huntly

This paper will discuss the ideas and actions that led to the development of a Drill Improvement Team at an open cut coal mine in Australia. It will show significant cost savings can be attained by forming a focused Team derived from all the participants that go into drilling a blast hole

Jan 1, 1999

By Michael David Wilkins, Paul N. Worsey

Little research has been published on stemming blast holes, particularly what happens during the process. Previous work has concentrated on the performance of the inert material to find the best way to seal the hole and retain the explosive energy, at the exclusion of determining what happens during the loading and stemming process.

Jan 1, 1998

By Stuart Pether, Cedric Goode

The Mt Morgans Minesite is located 800km North East of Perth, the Capital City of Western Australia. The surrounding region has been a significant producer of gold since the turn of the century. The mine was previously host to a township of approx 40 - 50,000 people.

Jan 1, 1996

By Thomas M. Keevin, Gregory L. Hempen

Accurate assessment of blasting near an object (organism or structure) requires recording of the damage parameter for low-valued scaled distances. Seismograph recordings of particle velocity are a well established, common procedure for land-based blasting. Similarly, pressure recording of the absolute waveform needs to be a more common procedure for sensitive, underwater resources.

Jan 1, 1997

By Keith Pucalik

One of the more important duties of the vibration consultant is to evaluate allegations of blasting damage by neighboring property owners. Unfortunately, the consultant is generally faced with having never seen the project, or preparing for litigation three or more years after blasting was completed. Under these circumstances, he must rely totally on blaster's logs and other contemporaneous records to conduct a meaningful evaluation.

Jan 1, 1990

By Calvin J. Konya

For proper blast design, one must make the assumption that all blastholes release nearly ideal energy. In many types of blasting operations, blastholes release very little useful energy. These blastholes are called malfunctioning blastholes. Recent studies indicate that as many as 30 percent of all blastholes are malfunctioning. These malfunctioning blastholes are not an unusual occurrence.

Jan 1, 1988

By C. B. Navalkar

The optimization of blast design under consideration is for the conventional driveways in under ground coal mines with respect to board & pillar workings in India. Basically The Blast Design includes following parameters: AA> Drilling Pattern. BB> Charging Pattern. CC> Material & Method Of Stemming. DD> Selection of type & quantity of explosives. EE> Initiation system & Blasting Sequence.

Jan 1, 2002

It is a case study of huge rock-mass, loosened out from the parent rock-body, & posing a potential danger to structures down below the slope on which this rock mass was standing. Case was dealt in two phases, by tying/stitching the rock mass to the parent rockbody and breaking it using controlled blasting technique.

Jan 1, 1997