Search Documents

By H. Bilgin, Sedat Esen

In this paper, the ground vibrations induced by blasting for stripping work at Sekkoy Open Cast Coal Mine belonging to TKI Yenikoy Lignite Mine (YLI) are investigated and the procedures for monitoring and control of ground vibrations are presented. Ground vibration measurements are conducted in the direction of Turkish Electricity Authorities’ Yenikoy Establishment and social facilities because of the complaints and annoyance arising from this site. Forty ground vibration records are taken in this direction and the vibrations are measured in transverse, vertical, longitudinal components together with peak vector sum. After then the scaled distance relationship is determined at 95% confidence value. Further, Fast Fourier Transform analyses are carried out to determine dominant frequencies for both ground and the structures and amplification factors. When the records taken at four different structures together with the ground are evaluated, it is observed that one of the apartment buildings is amplified the amplitude of longitudinal component 4.3 times. The maximum allowable amount of explosive that can be fired safely at this mine is calculated and recommended on. In the determination of safe amount, 95% confidence line, USBM RI8507 and OSMRE criteria, the dominant frequencies of both ground and the structure, amplification factor and the human response are taken into account.

Jan 1, 2001

By Q Liu, P D. Katsabanis

Dust explosions in underground sulphide and oil shale mines result from the detonation of explosives in the blasting operations. Explosive composition, oxygen balance, priming and ideality of detonation were examined theoretically and experimentally in the presence of reactive sulphide dust. It was found that the temperature as well as the chemical composition of the gaseous products of detonation are the controlling parameters related to the explosive. Non aluminized, oxygen balanced emulsion explosives were proven to be relatively safe, while explosives creating combustible products were proven to be extremely dangerous due to the secondary flame they generate. Since a large number of dusty orebodies are often very friable, low density emulsion explosives are also examined for application in production blasting.

Jan 1, 1991

By Hike Humphreys, Geoff Baldwin

A project aimed at blast optimisation for large open pit coal mines is utilising blast monitoring and analysis techniques, advanced dragline monitoring equipment, and blast simulation software, to assess the major controlling factors affecting both blast performance and subsequent dragline productivity. This has involved collaborative work between the explosives supplier, mine operator, monitoring equipment manufacturer, and a mining research organisation.

Jan 1, 1994

By John Cory, Ran Tamir

Blasting data analytics are being increasing used to increase mining productivity, reduce mining costs, maximize high margin aggregate products, and to reduce fines. Three examples will be illustrated using simple models to maximize the percentage of blasted rock within established dimensions and reduce fines-one from video fragmentation distribution information, the second from sieved crusher fragmentation data, and the third from plant production data. In addition, the use of sieved crusher results to determine blasting related fines and the use of mine productivity data to maximize aggregate sizes when pattern (burden and spacing) areas are changed will be illustrated

Jan 1, 2012

By G Alan Foster

The presence of approximately 600,000 attorneys in the U.S.A. and the determination by the courts that blasting is considered an 'ultra hazardous' activity makes every practical blaster aware that at some time during his working life he will probably be faced with defending himself in court.

Jan 1, 1982

By Tom McDonald, Rodney Burke

As mining progresses in the West, the depth of material has increased, making highwall stability a major factor in safety and production. The Jim Bridger Coal Mine has made highwall stability a priority, concentrating on safety as well as increasing and improving production. Overburden depths are increasing dramatically; the geological environment consists of medium to soft material, faulting, water, and current pit alignment not favorable to joint planes. Angle drilling the presplit at 20 degrees became necessary as vertical presplit drilling produced wall failures.

Jan 1, 1997

By R. Ticona, J. Alarcon

In the continuous search to provide comprehensive solutions and identify opportunities to improve ore traceability, from the blastholes to mill feed, different ore traceability systems have been developed, which allow tracking the ore and associating its geometallurgical characterization of different sectors of interest from blasting to the processing plant, facilitating decision making and operational actions when detected during each stage of the plant. With the objective of improving the ore tracking from the mine to the processing plant in a Peruvian copper mine operation, the impact on the processing plant was evaluated in relation to blasting optimizations through a tracker system, relating the processes performance of the whole production chain with the geotechnical and geometallurgical properties ores in real time in the process plant: detecting when it was feed waste, high grade ore, low grade ore and ore with arsenic, among others. Unit and integral tests were carried out over a period of three months, with an implementation of tracker detection portals in the processing plant, which allowed to verify the proper communication of data and the web platform. The tests were focused on several blasts where the ore was in contact with waste and it were directly sent to the plant, with a classification by type of grade (high, medium, and low grade), type of material (ore-waste contour), this stage allowed to make operational adjustments in the field and in the mining operation. Finally, in the economic results, the special tests had 1000 trackers, obtaining for this project a sensitization of a cost benefit for the test stage, for the reduction of 50% of the waste material feed has crushed, with an estimated benefit of 1,987,646 USD.

Jan 1, 2024

By Gregory B. Poole

Data collected with 16K sampling at a variety of blasting sites (construction, quarry, trench, mine) and monitoring locations was analyzed to effectively show the 16 different 1K readings all based on the microsecond that the unit went into monitoring.

Feb 1, 2020

By Pat McLaughlin, J R. (Dick) Daniels

Current practice in establishing quarries in remote areas with hilly or mountainous terrain tends to the use of airtracs (or similar pioneering units) drilling horizontal holes to establish a face, followed by bench development with light excavating equipment. The authors propose the use of a hybrid coyote blast design that incorporates long-round tunneling techniques. This method would, in effect, use down-the-hole (DTH) drills to advance the drift cut to the final depth, allowing longer and more rapid drift advances, and replace the cross-cut drifts with clusters of DTH holes to achieve the same explosives distribution.

Jan 1, 1995

By L. Chaves

In rock blasting, due to numerous factors, both controllable and uncontrollable, the execution rarely meets the planning. The powder factor is an important KPI for blasting since it represents the amount of explosive used to fragment the rock, therefore it depends on the rock mass characteristics and may be influenced by factors such as weathering and drilling quality. The blasts at the Serra Sul mine, S11D project, are usually big blasts and the high productivity is a challenge for maintaining the quality of the whole drill and blast process. It is important to know the contributions of each of the most common influencing factors of the powder factor to direct the efforts to the improvement of the process. A buildup model is presented to evaluate the contributions of five influencing factors to evaluate the planed x executed powder factor. The factors considered in the model are the average hole depth, the amount of hole/blasted volume, the stemming and decking length, the linear charge weight, and the density of the explosive used. The build-up may be applied for both individual blasts and for overall view of the blasts in a period. A case study is presented with the application of the model for the monthly powder factor analysis at Serra Sul mine has contributed to direct efforts to enhance drilling quality and preservation of the drilled holes.

Jan 1, 2024

By Raymond M. Dixon, Dale L. Ramsey

Upon being introduced to the MAGNETIC COUPLING concept,Balsinger,Inc. wanted to conduct field trials to explore the potential of Magnetic Coupling in the U.S.. Although the Magnetic Coupling Concept has been widely used, the U.S. proposed blasting criterion not previously addressed by the system. Modification to the system assembly and blasting accessories had to be made to make the system adaptable to our specific requirements. The field trials and system modifications are the basis of this paper.

Jan 1, 1990

By O. Rielo, A. Pascoal, P. Katsabanis

The dynamic parameters of two different granites have been obtained using Hopkinson bar experiments. One series of experiments were conducted using a Hopkinson pressure bar apparatus with an explosive source to provide the compressional wave. This wave would travel along the granite bar and would be reflected at the free end. Strains were obtained along the bar to examine the process. Using relatively long bars of rock, approximately 300mm long and 18mm in diameter, the separation of the compressive and the reflected tensile pulses was possible. If the net tension exceeds the strength of the material, spalling is witnessed. By properly selecting attenuation materials and explosive sources, single spalls were created, making results easier to interpret. Numerical modelling enabled the calculation of the propagation of the stress wave along the bar and its reflection at the free end. Knowing the location of the spalls, critical stress levels for rock failure under tension were obtained. Dynamic tensile strengths were also obtained, at different strain rates, using a Split Hopkinson Bar Apparatus. The results provide a measure of the increase of the dynamic strength at high strain rates, relevant to blasting applications. They are useful for the calibration of blasting models and the characterization of rocks for blast modelling, but also provide answers to the basic question of what is the rock strength for blasting applications.

Jan 1, 2011

By D T. Froedge

A new system for acquiring blast vibration data and a method for presenting that data in such a way that there can be an extraordinarily enhanced insight into the understanding of vibrations produced by blasting is described in this paper.

Jan 1, 1989

Jan 1, 2002

By I. Petropouleas, J. Croll, R. Bassett

A programme of tests on controlled internal explosions to a class of circular reinforced concrete columns, has allowed the relationships between the blast energy and the extent of local damage to be understood. These tests have also demonstrated the important additional effects on the damage levels of preexisting axial loads.

Jan 1, 2006

By Norman Kramer, Roger Keller

The authors would like to thank Austin Powder Company for their technical support and input, specifically Stephen Harris, Jason Ryan, and John Capers of Austin Powder, without whose support this paper would not have been possible. Thanks are also extended to Nick Francis of Sandia National Laboratories and Jim Houseworth of Duke Engineering for their input regarding Performance Assessment.

Jan 1, 2000

By Claude R. Ayoub, Charles A. Kliche, David G. McDowall

Homestake Mining Company's Open Cut Mine is located in Lead, South Dakota, in the northern Black Hills. The mine is within 300 feet of occupied residences on the south end, and within 1200 feet on the north end. Mining began at the north end of the open pit in October, 1983, and blasting related complaints began almost immediately. Noise and ground movement comprised the majority of the structural damage claims. As a result of these complaints, Homestake purchased a recording seismograph and began monitoring nearly every blast. In addition, the company hired a consultant to review Homestake's blasting and monitoring practices. He was also asked to do a single, one-time study of the cracks in six homes. This initial work led to Homestake monitoring all blasts with three seismographs and having South Dakota School of Mines and Technology do a year-long study of crack development and propagation in five homes in Lead.

Jan 1, 1989

By Sandy Tavelli, Thomas L. Barkley

This discussion will present a case study in developing solutions to a metropolitan quarry’s public relations, legal, environmental, and productivity problems. It details an extensive and detailed project to address the blasting practice in a medium sized quarry that is surrounded by residential and industrial zones. The principle work was done over a four-month duration during the normal production season. It included detailed drilling and blasting audits for baseline information. In addition, geologic characterization, seismic modeling, correction of deviations from best practices, and implementation and monitoring of precise electronic timing to provide dramatic solutions for the quarry. The quarry is in the near suburbs of a large metropolitan city. It is framed on two sides by residential municipalities and on two sides by industrial zones. At the start of the project, the quarry was in court as a result of the lawsuit by one of the neighboring towns that was suing to close the quarry. The lawsuit had progressed to the advanced stage where in the Judge had appointed an arbitrator to make the decision of continued operation. This arbitrator was to observe our progress and recommend to the Judge the disposition of the case.

Jan 1, 2004

By Frank Hammelmann, Peter Reinders

This paper briefly describes the past history of blast management. A modern blast management suite is then presented which demonstrates the current capability of the functional link between an electronic blasting system and blast design software. Finally, we look at the potential of tomorrow’s fully integrated blast management systems. From the first time blasting was introduced in mining as part of the production process, blasting technology and blast management have been interconnected. Over the past decades we have gained more recent experience with the new electronic blasting systems in mining, quarrying and construction. To start, the primary focus of electronic blasting was to increase timing accuracy. However, since then the technology has gradually developed, broadened and opened up new possibilities, including impressive flexibility in blast design and full in-situ verification of system functionality. To support this capability, modern electronic blasting systems are specifically designed to facilitate full two-way transfer of information between the office-based blast management software and field-hardened equipment. Blast management systems now comprise a suite of expert systems for planning, documentation, analysis, measurement and prediction of blasts. Within this blast management suite, the blast design software allows the transfer of the blast design information from a PC directly to the hardware of the electronic blasting system. The future development of this technology holds huge potential for the blasting industry.

Jan 1, 2004

By Midori Sakamoto, Nobuaki Sakuma, Tsuyoshi Murashita

Recently, tunnel blasting works near the residential area and existing building are increasing and environmental problems caused by vibration have become serious public concern. In order to solve these problems, blasting works have been conducted with segmented blasting and reduce advance per round. However, with these blasting, work efficiency is not obtained, and regrettably the cost and risk of accident tend to increase. We developed a new controlled tunnel blasting technique with electronic delay detonator. Electronic delay detonator can supply extremely large range of delay period which could not be achieved with conventional pyrotechnical delay detonators. We utilized advantages in initiating hole by hole over entire tunnel face at the same round. Much seismic data obtained from tunnel blasting with conventional detonator was statistically analyzed in order to find average duration time of vibration caused by a single hole initiation. Numerical simulation using sample waves from a single hole initiation was carried out in order to find an optimum delay time which can separate vibration in each hole initiation and without decreasing blast performance. Trial blasting was conducted to examine the correctness of optimum delay time obtained from numerical simulation. This blasting technique was applied to an actual tunnel construction. This tunnel is 2 lane automobile tunnel with a total length of 659 meters and internal cross section of 70 square meters. The purpose of the use of blasting technique on occasion, was the protection of fresh water reservoirs directly above the tunnel, and to keep the effect on local private houses to a minimum. The vibration level against this station was limited under 20 mm/see P.V.V. With this blasting, the tunnel construction was completed without exceeding the limited vibration level, with minimum cost and construction time.

Jan 1, 1998