Search Documents

By Tapan Goswami

This paper discusses the importance of coal mapping, the rock properties of the roof and floor interface of the coal seam, and the significance of loading and initiating designs in minimising coal damage. Furthermore, the importance of using electronic initiators cannot be emphasised enough. This paper also discusses how a cast blast can be initiated from many locations by mitigating geological abnormalities and thereby avoiding spatial movement of rock shearing in a plane above the coal seam.

Feb 1, 2020

By CVB Cunningham

"The Kuz-Ram model as originally proposed included an error in assuming that the mean fragmentsize predicted by Kuznetsov’s equation was actually the 50% passing size. In 2003 Spathis began discussions on this issue and recommended correcting the equation. The correction produced more fines in the predicted fragmentation, which had been a criticism of some users of the original model. Ouchterlony subsequently showed that the error had, if anything been beneficial, and that the Swebrec function adequately covered the fines. This author shows that the Spathis correction does not assist the fines correction in examples examined, but tends to underestimate coarser fractions. An intrinsic problem of communication between academics and engineers is a root of misunderstanding on both sides, and requires patience by both parties to enable value to arise."

Jan 1, 2016

By Miguel Araos

The aim of this study was to understand clearly how VOD of emulsion-based gassed explosives is influenced by parameters such as nitrate salt composition in the oxidizing phase, product density, blend composition, gassing rate, type of sensitization, etc. Also some VOD testing was performed on watergel-based gassed explosives in order to compare the results with those obtained for emulsions. VOD measurements were conducted in the surface blasting facility at the Research and Development laboratory of ENAEX SA (Calama, Chile). Despite the fact that the influences of some parameters on VOD of emulsion-based gassed explosives are easily predicted, there was found to be an unexpected correlation. Although it is commonly believed that the VOD of gassed explosives depends on the density, this study found that the VOD depends on the both size and the amount of gas bubbles incorporated into the product as well as type of sensitisation, regardless of whether the explosive was straight emulsion or a blend. Density is just a consequence of the incorporation of voids into the explosive. Future work in this area may examine variation of other parameters, in order to obtain a greater knowledge of detonation properties and therefore to design more efficient explosives.

Jan 1, 2002

By Thierry Bernard

Considering rock fragmentation by explosive as the ultimate goal in mines and quarries, vibrations are definitely one of the main drawbacks faced by the Industry. If we can accurately predict vibrations level and frequencies, taking into account the whole set of the involved parameters, this will bring a major benefit to each of us, in our daily production process optimization effort. The model presented in this paper answers to this need thanks to a "holistic" approach of the vibration mechanism. By holistic, we mean that we approach the vibration effect (wave propagation) as a whole, by understanding all of the mechanisms that contributes to the process and comprehending how they are connected.

Jan 1, 2009

By Sean Cahill

The Blasting In the summer of 1999, a Southern California drilling and blasting company conducted blasting as part of the grading operations at the Highlands Ranch development in San Diego, California. Highlands Ranch was a new single family residential project located near older residential properties in the area. Blasting was necessary to remove indigenous meta-volcanic rock associated with the local geology.

Jan 1, 2003

By Andrew F. McKown, Robert A. McClure

This paper will describe a trench blasting case history in close proximity to several adjacent structures, including a bridge abutment, railroad tracks, and utility pipes. Some design considerations involved in close-in blasting will be discussed, including allowable peak particle velocities and prevention of rock block movement. The importance of several trench blast round design factors is pointed out, including choice of explo sive to prevent propagation, maintaining a sufficiently high powder factor, and mucking out for maximum relief after every round. Vibration monitoring and good record keeping are shown to be important in order to evaluate blast problems and make modifications to round designs.

Jan 1, 1988

By Robert Hopler

SECTION 9.---BORING AND BLASTING.*155. Blasting is the operation of bringing down and detaching from its bed or position masses of material by means of explosives.

Jan 1, 2011

By Marcus Neves, Eventomar Junior, Adilson Castro, Leandro Silveira, Sérgio Augusto

The collapse of the Vale S.A. mining tailings dam in 2019, a tragic event that shook Brazil and the world, had consequences that transcended the immediate pain and devastation. Among them, the suspension of rock blasting activities in several mines in the Quadrilátero Ferrífero region of Minas Gerais, Brazil. This measure, taken as a precaution and with the aim of ensuring the safety of nearby geotechnical structures and the population, had a significant impact on the mining production chain. To overcome these challenges and resume blasting activities in a safe and sustainable manner, the mining industry has been dedicated to developing and improving solutions. One of the promising alternatives is the signature hole technique, used in conjunction with attenuation laws. The complex geology of the Quadrilátero Ferrífero, with lenses of compact ores immersed in friable materials, the presence of discontinuity families, and the emergence of geological faults, requires detailed analyses and specific adaptations of the signature hole technique and constant monitoring of the vibrations to calibrate the attenuation laws to ensure compliance with permissible limits and safety of the operations. To demonstrate the methodology, a case study in Abóboras Mine was described. Additionally, the challenge of achieving the desired level of production while controlling vibration and slope damage has driven the development of new charging and timing techniques. To address this challenge, a comprehensive approach was undertaken. A substantial database containing more than 4,000 registers of blasting-induced vibration events from 520 blasts was meticulously compiled from 2020 to 2023, 6 different attenuation laws were established and continuously calibrated with 99.3% of compliance regarding permissible limits of vibrations. The successful implementation of these actions allowed for the resumption of blasting, increasing production from 10 million metric tons to 43 million metric tons per year assuring sustainable operation.

Jan 21, 2025

By Shawn Kirkpatrick, Yang Ruilin, Tamara Whitaker

In order to manage blast vibration in soft ground containing large diameter holes and large charge weights, a number of issues must be considered. This paper describes techniques to control and reduce near-field blast vibrations absorbed by highwalls in soft ground. Sympathetic detonations need to be controlled. Sympathetic detonations can cause excessive vibration due to an unknown number of charge weights firing out of sequence. The excessive vibration can cause damage to the ground. Sympathetic detonations can be controlled through proper design of blast patterns and, in some cases, through the use of specialized electronic detonators.

Jan 1, 2009

By Chris Breeds, Larry Leone, Jerry Wallace

One of the Authors was recently retained to provide a professional engineering analysis of the potential impacts from underwater blasts used to enlarge intake tunnels at the Cheesman Dam near Denver in Colorado and to design Blast Protection Bags that could be installed in each tunnel to protect the 100- year old downstream valve structures.

Jan 1, 2012

By E. Contestabile, B. von Rosen

Recently, the Canadian Explosives Research Laboratory (CERL) completed its investigation of a truck accident, which involved 18,000 kg of commercial explosives, 13,000 kg of which was ANFO. Over the three years of the investigation unconfined burns of piles of ANFO were performed. In its final phase of the investigation, two burn trials were performed in an attempt to recreate the accident and the ensuing fire, to identify probable mechanisms that led from burning to detonation. Two full-scale tests were performed using complete tractor-trailers. In each test, the trucks were placed in a jack-knifed position with the majority of the explosives located on the ground in front of the trailer. The explosives were placed in a manner to provide maximum confinement and to maximize the possibility of explosion/detonation while remaining as faithful as possible to the perceived accident geometry. The tests were instrumented using thermocouples and video cameras and observations were made on the burning characteristics of the explosives, tractor-trailer and tractor-trailer components. In each test the explosives burned calmly for approximately 80 minutes. There was no evidence of explosion or of unstable burning. The heat caused several truck components to rupture violently. These included the tires, some engine components, the spring brake chambers and possibly the fuel tanks. Of these, the most violent were the truck tires. Although no quantitative data was gathered on rupture violence or fragment velocity, it is speculated that several truck components might produce fragments with sufficient energy to initiate heat-sensitised explosives under favourable circumstances.

Jan 1, 2004

By Zong-Xian Zhang

In sublevel caving mines, serious eyebrow break usually gives rise to lower ore recovery, higher dilution, and worse safety for the people working in the field. For example, chargers must go near the caving region and stand under the damaged eyebrow where a hanging stone may suddenly fall down or rock fragments may quickly roll down.

Jan 1, 2011

By Thomas Leonard, Philip R. Berger, Bryan E. Papillon

Bardon Trimount Inc., a large producer of aggregate, crushed stone, and concrete, was experiencing significant public opposition to its five quarries in the Boston area. It was believed by the authors that this opposition could be significantly lessened if the total number of blasts per week were reduced. Although the blasting company at these quarries, Austin Powder Company, contended that this could easily and safely be accomplished by increasing the size of the blasts, regulations precluded this alternative by limiting the total amount of explosives that could be used per blast.

Jan 1, 1996

By S. Hosein, W. Birch, C. Johnson

The widespread adoption of electronic detonators has given rise to the development of linear superposition to control the environmental impact on both third-party properties and residents resulting from blast induced vibrations. Linear superposition has become a very effective tool in the hands of blasting engineers and has enabled aggregate reserves to be accessed that once had to be abandoned. This in turn has resulted in more and more complex blasting pattern to be developed that contain multiple rows and multiple decks all with different maximum instantaneous charge weights of explosives. This is then made more complex by having to consider multiple sensitive locations often with different Peak Particle Velocity vibration limits. This paper is a case study of what did happen when a blast was designed that “pushed the boundaries” of environmental blast vibration design and control, without taking fully into account the fundamental geophysical properties of seismic waves. The resulting blast design caused a greatly enhanced s-wave to be created in a critical direction from the blast pattern. The root cause being the s-waves from earlier detonating decks in the blast pattern arriving within 2 milliseconds of decks detonating later in the blast pattern. 209 individual decks were fired in the blast pattern of which 41 pairs of decks arrived at the observation location less than 2 milliseconds apart when taking into account the s-wave speed and direction. The lesson to be learned when using electronic detonators to limit ground vibrations from complex blasting patterns, is that it is just not good enough to look at the planned firing times, a professional blasting engineer must also understand the likely interaction of the various seismic wave types created and their combined impact on any given monitoring location.

Jan 1, 2024

By Michael K. Phang, Thomas A. Simpson

Field studies at an underground mine site were conducted to evaluate and monitor blast-induced vibrations on an underground coal mine roof. The vibration data were evaluated so that a suitable damage criteria or guidelines from which a safe operating distance between surface blasting and underground mine operations can be established.

Jan 1, 1984

By Jeffrey W. Lin, Jonathan D. Abbott, Patrick R. Bowden, Tyson J. Plitt

Pentolite is a class of high explosives containing trinitrotoluene (TNT) and pentaerythritol tetranitrate (PETN) with PETN content typically ranging from 40 to 60 wt%. Manufacture involves melting TNT, 80 °C, followed by addition of PETN and trace ingredients to form a homogeneous mixture. Once a mix is ready to be poured, several factors can influence the behavior of the finished product including how long the mix has been at temperature and cooling rate. After the manufacturing process has been completed, storage conditions combined with manufacturing conditions may cause physical changes. Two such changes explored were exudation, liquid exuding from solid boosters, and ratchet growth, irreversible volumetric expansion. Exudation is principally caused by excess water in the process. Ratchet growth is a common phenomenon of nitroaromatic compounds such as TNT where time and temperature fluctuations can cause materials to increase volume, simultaneously decreasing density. Although neither phenomenon affects common attributes such as sensitivity, performance, and shelf-life, both can cause issues in storage and handling. In this study pentolite was cast into various forms under different manufacturing conditions and evaluated over several months of controlled storage conditions including ambient, temperature cycling and elevated isothermal. Subjective and objective measurements were made throughout the evaluation period with the aim to determine the preferred storage methodology.

Jan 21, 2025

By Glenn Tobin

The overarching goal in modern drill and blasting operations is that of optimising mining operations to achieve higher levels of productivity, safety, profitability and sustainability. Air decking, a technique used in drill & blasting to optimise explosive product use while achieving a target rock fragmentation1, is a technique that when executed correctly is proven to achieve consistent results independent of rock strength and the position of the holes (single, multiple, vertical, slanted), as well as being proven to reduce super-fragmentation (under-size or fines) while able to achieve optimal fragmentation, especially in the stemming zone2. The ‘shock absorber effect’ if the air deck reduces ground vibration and air blast3. Additionally, the practice of loading explosive product directly in saturated ground without dewatering or lining prior is an increasing global trend.

Jan 1, 2012

By Stephen H. Chung

Direct visualization of rock movement during blasting is an important key to understanding the blasting process, as well as optimizing blast designs and explosives performance. To achieve this, a digital camera system (HSIS-500) has been built. It is a custom made high speed solid-state camera employing an advanced charge coupled device (CCD) and dynamic random access memory (DRAM) technologies. It handles like a regular video camera but requires no film or tape as the image is recorded in digital form on memory chips and transferred to the system hard disk for storage. The system consists of two components: the camera body and hardware, and the image processing unit.

Jan 1, 1996

By Agung Wibowo

The incident of Ammonium Nitrate explosion in Beirut on August 4, 2020, became a wake-up call to Ammonium Nitrate stakeholders for mining and construction regarding the deadly risks associated with explosives management. This is a very expensive a lesson learned for all parties involved in the storage of explosives.

Feb 1, 2020

By Tapan Goswami, Geoff Keith

"At Bulga Coal, the objectives of drilling and blasting are to maximise safety and to minimise the totalcost of mining. A recent audit of two overburden blasts established that the standard of drilling and blasting is excellent. No apparent hazards were identified. Laser profiling showed that highwall free faces are reasonably planar with some exceptions, thereby promoting uniform burden distances along front-row charges. However, in three isolated areas along one face, small burden distances existed. The mean and the standard deviation of errors in the collar positions of front-row blastholes was found to be 0.3 + 0.03 m. A borehole video camera was used to show that blastholes did not feature open bedding plane partings, cavities or damage produced by the blast in front of them."

Jan 1, 1999