Search Documents

Two of the most important economies in coal-washing are in the actual washing of the coal and in a proper lay-out to reduce to a minimum the cost of labour for handling and washing. A guarantee is usually required for turning out a washed coal containing not more than 2% of free dirt and a resulting refuse with not more than 2% of free coal; any plant that gives results within such guarantees can he considered economical, provided that there are no other losses during the washing process. Various drainage arrangements and washery lay-outs are illustrated and discussed with respect to drainage, bunkers, sieves, settling tanks and conveyors and two further points considered: siding accommodation, which may become quite important with washeries of large capacity especially when the coal is brought in railway-wagons; and the irregularity with which the coal arrives. (Paper presented at the Manchester Geological and Mining Society's general meeting held in Manchester, April 11th 1916, with Mr. Leonard R. Fletcher, President, in the chair)

Dec 1, 1916

By B. Sonmez, B. Aksanl, S. Ersaym, I. F. Erkal, S. L. Ergun

The comminution circuit at the plant has experienced severe problems arising from a feed containing much larger amounts of clay and having a higher moisture content than expected. Three solutions were proposed: replacement of the crushing circuit by tooth roll-type crushers; using washing drums; and introducing primary autogenous/semi-autogenous millling instead of crushing. Computer simulations studied the effects of the first two solutions on the circuit capacity. Laboratory and industrial scale ball mill batch grinding tests were carried out. The parameters of a kinetic model were determined. The ball mill circuit was sampled and operating model parameters were calculated. The ability of batch grinding parameters to represent the operating conditions was studied. Tests failed to find acceptable model parameters, but parameters from an industrial size batch mill were found to be suitable for simulation studies. The simulations indicated that a continuous feed of -12 mm provided by tooth roll crushers would maintain the desired capacity. Increasing the feed size to -25 mm would reduce the capacity by 8-15%. The use of washing drums could also solve the capacity problem, but small fluctuations in water flow rates might result in problems of excess water in the grinding circuit.

Jan 4, 1993

By I S. Lowndes, K. Moloney

Diesel powered equipment is currently used extensively in mining and tunnelling operations around the world due to its mobility, flexibility and through selective application to enhance productivity. However, the increased use of diesel equipment has exacerbated the pollutant load (including heat, humidity, exhaust gases and particulates) placed upon the environmental systems of many underground operations. This expansion in the use of diesel equipment has prom pted researchers to evaluate m easure ment and control technology. This paper reviews the recent research conducted in various countries.

Jan 10, 1996

By N. A. Warner, R. K. Manna

Physical modelling of liquid-phase oxygen mass transfer in a water model of part of a proposed new polymetallic smelter has been achieved. A study of solute mass transfer caused by multiple, subsonic air jets contacting superoxygenated water flowing in a channel model of the smelter converting hearth has been carried out. For a wide range of channel flow rates the rate of mass transfer was found to be independent of water velocity. The water model has been used to compare mass transfer for both open-packed and close-packed multiple-lance arrays with circular nozzles of diameters 2.26, 4.95, 10.95 and 24.40 mm. It was found that with fewer of the larger-diameter nozzles a reduction of up to 58% in liquid-phase mass transfer occurred, especially for the close-packed lance configurations. This restriction of liquid-phase mass transfer would result in reduced metal losses in the analogous smelting situation. The larger nozzles, however, exhibited more jet-jet and jet-channel wall interference effects than their smaller counterparts, resulting in an effective reduction in the momentum fluxes of the impinging jets

Jul 1, 1991

By Q. H. Liao, B. G. Monaghan

The options for designing slopes in complex geological conditions are reviewed. It is shown that modelling, especially numerical modelling, allows a degree of analysis that cannot otherwise be achieved. Examples are presented of how numerical modelling can be used to investigate fundamental aspects of rock mass behaviour. It is demonstrated that an important consequence of change in scale is that the mechanisms of failure also change. The complex failure of the footwall slope at Aznalcollar, a large open-pit mine in southern Spain, is discussed. Numerical modelling with UDEC (universal distinct-element code) has allowed the realistic simulation of displacements measured in the field

Jun 18, 1905

By Winmill T. F.

The previous papers have been concerned only with the atmospheric oxidation of coals from the Barnsley Seam, for which it has been shown that an adequate explanation of the origin and nature of gob-fires can be based on the reaction between the coal itself and the oxygen of the air without the intervention of any other substance. It becomes of importance, therefore, to ascertain how far a similar explanation will hold good for spontaneous heating in other seams, and with this object in view samples including anthracite and lignite have been taken from a considerable number of pits in different parts of the UK (south Wales, Northumberland and Durham, north Staffordshire, Portrush and Ayrshire), some liable to fire, others not. There is abundant evidence to support the commonly-accepted view that spontaneous heating is due to the heat evolved during the absorption of oxygen from the air by coal or pyrites. The quantity of heat produced by the reaction has been measured and it has been shown that the observed rate of heating of a sample of coal agrees with the rate calculated from the heat of reaction and the rate of absorption of oxygen

Dec 1, 1916

By M. G. Fleming

The professional mineral engineer is an individual of personal integrity who has undergone rigorous intellectual instruction in the scientific disciplines fundamental to his vocation; he has learnt to apply these disciplines to the discovery, mining and treatment of mineral resources and, through practical training and experience, has acquired competence and judgment to fulfil his undertakings. In the course of this development he has recognised and accepted a threefold responsibility to society, to his employer and to his profession

Dec 1, 1971

By John Craw

This paper has formulated the methods, both medical and engineering, for the control of pneumokoniosis in the haematite-mining industry in West Cumberland, but this is only part of a general service to improve the lot of the worker in these mines, to make him a better and happier workman, and to permit him to enjoy his work and leisure in comfort and good health. This organization has now been functioning for more than ten years and the results are indeed heartening, but it is only as a result of constant vigilance from the mining and medical point of view that such a plan can operate efficiently. The human element and its full understanding is by no means the least of the problems.

Jan 1, 1947

By E. H. Baker

Vapour pressures of sulphur have been measured over the temperature range 340-1039°C by means of boiling-point measurements, an internally heated pressure vessel being employed with argon as the pressure medium. The results are expressed satisfactorily by a four-term pressure-temperature relation. At the cited critical temperature of 1040°C the calculated critical pressure is 204 atm. From the pressure-temperature relation and available thermal data for the vapour, the approximate composition of the saturated vapour in terms of the various molecular species has been derived for the critical point

Dec 1, 1971

Discussion of the paper presented at the Manchester Geological and Mining Society's general meeting held in Manchester, April 11th 1916, with Mr. Leonard R. Fletcher, President, in the chair, included questions asked and points for discussion raised by Bramall V., Paton J.D., Fletcher L.R., Siddall F.N., Stoker A. and Stone T., in particular on how to eliminate dust

Dec 1, 1916

By I. A. Scott, T. J. Napier-Munn

Size-by-size partition curves for mineral separation in dense-medium cyclones pivot about a single characteristic point. This is defined for stable, non-segregating media by the medium density and the proportion of the medium reporting to the underflow. The pivot point departs from these values for unstable, conventional media. The phenomenon can be represented by an equation with two parameters defining pivot point coordinates and two the Ep value. On the basis of experiments in a 200 mm cyclone using ferrosilicon media, simple regression equations were developed for the separation parameters in terms of operating conditions (the coefficients were likely to be site-specific). The experiments successfully decoupled the effects of medium density and viscosity and showed that the value of Ep was independent of the former but strongly dependent on the latter. A classification model was used to predict the density of the underflow medium, a knowledge of which is required to determine the pivot parameters. The model correctly reflects the performance trends observed in dense-medium cyclone operation and has the potential to be generalised to a wide range of industrial practice.

Jan 8, 1992

By J. H. Chesters

The main, though rarely mentioned advantage, is likely to be the standardisation of best practice and product. In a batch process conditions vary cyclically, but with a continuous process they would, at least ideally, remain the same for long periods of time. The other main advantages of continuous over batch processes are likely to be reduced operating and capital costs, the improved possibilities for automatic control, and more consistent product quality. Recent developments are surveyed for ironmaking and steelmaking with reference to blast furnaces; solid-product and molten-product direct reduction; the trough-type processes of Thring, Worner, the Japanese National Research Institute for Metals and Glinkov; basic-oxygen furnace (LD) variants; spray steelmaking; continuous casting and vacuum degassing; rolling; and coating. Encouragement in the devleopment of continuous processes may be drawn from the way unexpected difficulties, such as trouble with sulphur and refractories, were tackled and overcome to achieve the float glass process

Dec 1, 1971

By R. R. Liebenberg, M. I. Brittan

The kinetics of the copper segregation process has been investigated. The experimental strategy used to isolate the rate-controlling reaction step is described. This step was found to be the chloridisation of the oxide copper minerals in the ore. The link between the rate of chloridisation and the overall rate of segregation is demonstrated experimentally. The influence on the kinetics of the various parameters in a TORCO system is examined and the implications are discussed

Dec 1, 1971

By A. L. W. Lips, B. P. J. Stevens, T. J. R. Barclay, E. Rothery, S. H. White

Discussion by B.P.J. Stevens of the paper, published in Trans. IMMA, vol.104, 1995, p.B1-B17, is presented together with the authors' response. Stevens questions the authors' radically different interpretation of the structural geology of the Broken Hill Block, considering that the descriptive part of the paper is a useful addition but that the conclusions are unwarranted on the basis of the data presented. A number of major points of disagreement are outlined and half a dozen additional minor points listed. In response, the authors admire Stevens's contribution to unravelling the geology of the area but defend their attempts to take the regional studies a step further, pointing out that he has misquoted what they wrote and arguing that because of the assumptions underpinning the derivation of the present stratigraphy it cannot be used to constrain structural models. With regard to shear zones, they cite the extensive earlier literature and refer to horizontal displacements shown on maps produced by Stevens et al. Detailed discussion follows of the stratigraphy and of the stratigraphic correlation problems resulting from failure to recognise the presence and significance of shears, particularly those parallel to stratigraphy. The remobilised position of the Pb mineralisation in the North Mine open cut is reiterated. It is concluded that there is an urgent need for systematic isotopic dating in the area to constrain the stratigraphy

Apr 1, 1996

By A. L. W. Lips, B. P. J. Stevens, T. J. R. Bareley, E. Rothery, S. H. White

B.P.J. Stevens contributes a further response to the authors' earlier lengthy reply regarding their paper published in Trans.IMM B, vol.104, 1995, p.B1-B17, contending that despite the positive contribution clarifying their interpretations they perpetrate some misquotations, attempt to rewrite history and fail to understand the New South Wales Geological Survey's stratigraphic interpretation of the Broken Hill area. The paper's authors, in their further response, robustly defend their views, insisting that Stevens tends to misquote or take out of context what they have written and reiterating their findings that Zn is tectonically stacked above Pb at the north end of the orebody, that the written development of the stratigraphic interpretation is as they have stated, that shearing has attenuated or removed fold limbs in the Broken Hill block and that the 1:100 000 stratigraphic map reveals that magnetic anomalies are oblique to and truncated by the Geological Survey's interpreted stratigraphic boundaries

Jun 19, 1905

By M. J. Howes

The high degree of mechanisation, which is mainly diesel-powered, has a significant effect on heat loads; heat output from this source often exceeds the heat flow from the surrounding rock. The extensive use of diesel-powered equipment also influences ventilation rates and minimum values are necessary to ensure that emissions of diesel exhaust are adequately diluted. Many Australian mines are in subtropical or tropical areas with high ambient wet- and dry-bulb temperatures on surface. This, coupled with the large amount of heat from mechanisation, usually means that refrigeration is required at much shallower depths. A secondary problem is associated with the definition of acceptable thermal environment conditions, which are sometimes based on the assumption of no air movement. This gives rise to very stringent thermal environment acceptance criteria, which, in some areas, would prohibit work on surface, let alone underground

Jun 12, 1905

By R. R. Hart, R. A. Evans

This paper outlines the the methods currently being used in the West Wales Area for preventing the occurrence of any outbreak of spontaneous combustion. Stress is placed on the importance of correlating the position of a Rider Seam which is prone to spontaneous combustion. The recent introduction of the UNOR Recorder has contributed to the ability to monitor the CO content of the general body of the air during any incident. The use of modern sealants and improved methods of applying them have enabled the few instances of spontaneous combustion in South Wales to be treated promptly and efficiently. The authors describe the current spontaneous combustion problems at two collieries.

May 23, 1905

By G Fakes

This paper describes the history of civil engineering tunnelling and developments in soft ground techniques during the 19th and 20th centuries, culminating in the design and use of high speed tunnelling machines for all types of ground conditions. Some of the problems encountered are outlined, and descriptions are given of some contemporary developments in rock tunnelling techniques, with comparisons of methods used in the mining industry.

Jan 5, 1996

By L. T. Matthews, C. E. Loo

During sintering, porous ore particles are easily assimilated by liquid melt. Two simple models of the process are considered: the dissolution of a solid by a liquid and the penetration of a liquid into a porous solid. Laboratory sintering studies covering a range of experimental conditions were undertaken to characterise the assimilation of large particles of ore and flux by melts formed from different mixes of fines. For ores, the process appeared to be complicated by the detachment of fines from the ore surface prior to melt formation, according to the mass of adhering fines and surface roughness of the particle. This delayed the onset of assimilation and sometimes reduced it, although melt penetration was fast and effective. Studies using different temperature profiles suggested that the assimilation of haematite was controlled by the transport of Fe2O3 away from the surface of ore particles. The assimilation of limestone depended more on thermal conditions than on the three magnesia-bearing minerals considered. Changing the composition of the initial melt significantly altered the extent of assimilation of ores and limestone, but again had a less marked effect on the magnesia-bearing fluxes.

Jan 8, 1992

By J R. Leeming

The paper describes a technique that has been developed by the Health and Safety Executive (USE) to make an assessment of the effectiveness of Health and Safety (H and S) management at complex sites. The paper then describes how the technique was adapted and used for the first time at a large coal mine. The results highlighted certain deficiencies in the safety management system, allowing directed advice to he given to management.

Jan 4, 1997