Search Documents

By D. J. Burdon, Anthony Caplan

"(1) The radiological appearances of pneumokoniosis on the Kolar Gold Field is described in detail. The characteristic abnormality is the. presence of a diffuse, fine annular and punctate mottling. (2) The frequency of symptoms could not be determined with any degree of accuracy, but it is believed that symptoms are absent and there is no incapacity until profuse radiological mottling is present, i.e., after long exposure to dust. (3) There is an increased predisposition to tuberculosis, which, if it occurs, affects the prognosismost unfavourably.(4) Pathological examination shows that the radiological mottling is due to the presence inthe lung of numerous small dust-cdll aggregates (up to T5 mm. in dia.) deposited around the smaller bronchioles and blood-vessels.(5) The dust-cell aggregates are relatively acellular but when tuberculosis is superadded thereis an excessive cellular and fibrotic reaction.(6) The difficulties of defining the radiological and pathological appearances of early pneumokoniosisare discussed.(7) The incidence of pneumokoniosis in 7,653 workmen with 5 or more years’ undergroundservice was 43-75%, but it is suggested that in future the incidence will be appreciably lower.(8) The methods of- dust production and the chemistry of mine dust are described. It isshown that the free silica-content of air-borne mine -dust is relatively low.(9) The aetiology'of the pneumokoniotic lesion is discussed."

Jan 1, 1947

By M. Foguenne, A. van Lierde, P. Henry

Leaching experiments were carried out on a spent catalyst sample with a honeycomb structure, containing 47.5% Ti, 5.8% Mo, 2.7% Si, 2 035 ppm As, 52 ppm Pb and 8.8 ppm Hg. More than 93% of the Mo and As was removed by direct alkaline leaching after grinding to 80% -36 micrometres. The residue contained 0.3% Mo and 60 ppm As. To obtain a TiO2 matrix with 30 ppm As, acid leaching at controlled pH with 90 kg/t Al scrap was followed by oxidising alkaline leaching. Treatment of the direct alkaline leach solution or of the mixed solutions from the two-stage process involved two successive operations: purification by neutralisation with Al(OH)3 addition to raise the Al concentration to 4 g/l, and ion exchange on Amberlite IRA 94 S resin. Whatever the type of solution treated, elution with 200 g/l NH4OH solution gave an eluate of very high purity containing 164 g/l Mo, less than 70 mg/l V and less than 2 mg/l As

Jun 19, 1905

By Dean S.

Further discussion at the North of England Institute of Mining and Mechanical Engineers' general meeting held in Newcastle-upon-Tyne, 12th February 1916, with Mr. T.Y. Greener, President, in the chair, of the paper published in Trans. I.Min.E. vol.L, 1915, p.179 and 388. Written contributions to discussion included Mr. Dean's reply to earlier discussion (p.35-44), further written contributions by Tate S. (p.44-54) and Brown E.O.F. (p.54-56), and oral comments by Hare S., Merivale J.H., Greener T.Y. and Tate S. Particularly debated were the causes of the difference in output between American and British coal miners

Dec 1, 1916

By M. C. Amiri

The plant produces 130 kg slag per tonne of crude steel, to add to the basic oxygen steel-making converter slag stockpile of around 2 500 000 t. The slags contain 1.81% V2O5, which can be rendered water-soluble by salt roasting with NaCl and an alkali such as Na2CO3. Preliminary tests gave less than 3% V recovery from slag under optimum roasting conditions when NaCl, NaCO3 or Na2SO4 was used, but showed that sodium phosphate could make all the V water-soluble when roasted with slag in a ratio of 3:1 at 1 100-1 200 degrees C. Almost complete leaching was obtained within 2 h with water at boiling point. Sodium vanadate was precipitated by acidifying the leach liquor with HCl to a pH of about 2.2

Jun 21, 1905

By S. L. R. Lenharo, H. Kahn, H. Born

Different ore types result from the irregular spatial distribution of the associated alkaline/carbonatite rocks and the zoned alteration profile within which apatite may have undergone reprecipitation. Different flotation responses are caused by their mineralogy, iron oxide impregnation and grain-size characteristics. Samples from seven deposits were crushed, screened and separated before being studied by chemical analysis, optical microscopy, X-ray diffraction, FTIR spectroscopy, cathodoluminescence and scanning electron microscopy. Two main apatite varieties with peculiar crystal morphology were identified: hydroxy-fluorapatite as the primary phase and carbonate-fluorapatite as the reprecipitated phase. The former occurs as prismatic or ovoid grains and the latter as polycrystalline aggregates or crusts on the primary grains; both are associated with iron oxide coatings (primary) or intergrowths (secondary). Microflotation tests showed variations in flotability for particular apatite associations as well as intensity of iron oxide coatings. The differences in flotation behaviour can be related to morphological properties and chemical substitution in the apatite structure

Aug 1, 1996

By T. Yalcin

In the Box-Wilson method, the correlation between dependent and independent variables is represented by a polynomial response function, whose constant and coefficients are determined by applying regression analysis to the experimental data collected. The five levels used for each variable consist of a minimum, a maximum and three intermediate values. A study was carried out using Ni-Cu ore from Sudbury, Ontario, in which 15 experiments designed according to the Box-Wilson method were carried out in random order and in duplicate. The two sets of replicate data showed close similarity, with an overall variance of 0.311 for the five parameters studied. The response functions were used to optimise frother dosage, collector concentration and air flow rate and an experiment was then carried out under the optimised conditions; the results agreed closely with those predicted by the response functions

Jun 21, 1905

By P. A. Davies

Paper presented at the conference: Risk assessment in the extractive industries, held in Exeter, UK, 23-24 March 1994, and first published London: IMM, 1994, preprint volume, 11pp., 15 refs. Hazards such as vibration, dust emission and fragment projection can result in an area called the Danger Zone being set around a blasting site. Traditionally Danger Zones have been set solely on the basis of consequences (e.g. based on the maximum distance of rock projection or expected ground vibration plus a defined safety margin). Advances in risk assessment and its growing acceptance as a safety management tool have led to the setting of Danger Zones based on both consequences and frequency of occurrence. This allows distances to be optimised on the basis of acceptable risk levels rather than the potential consequences of infrequent events. The setting of a flyrock Danger Zone is used to demonstrate a risk-based approach compared with a traditional consequence approach

Aug 1, 1995

By R Adamian, F. T. Da Silva, D. H. Gameiro

Schytill and Geldart diagrams were developed for the TiO2-C-Cl2 system at 1 073 and 1 273 K, so as to define the hypothetical relations between particle sizes and chlorine velocity for simultaneous fluidisation of mixtures of anatase concentrate and charcoal for carbochlorination. It was concluded that the operating limits on chlorine gas velocity will be controlled by the behaviour of the reducing agent, mainly because of its lower density. An increase in temperature from 1 073 to 1 273 K will have only a small influence on the fluid-dynamic behaviour of the mixture. For bubble fluidisation, the maximum sizes 0.413-0.478 mm for anatase and 0.529-0.611 mm for charcoal will be adequate. When the particle size distribution is large, fluidisation will be feasible only if conducted in two stages, otherwise the residence time of the small particles in the reactor will be very short. New diagrams will be needed for the gaseous chlorides in the second stage

Jun 21, 1905

By F. T. Da Silva

Concentrates of titaniferous minerals containing around 30 wt% Ta2O5 are processed hydrometallurgically by hydrofluoric acid leaching and solvent extraction, followed by the precipitation of hydrated potassium heptafluorotantalate. A fundamental study of the thermodynamics of this precipitation and recrystallisation was undertaken to increase understanding of the conditions most conducive to the production of pure, well-crystallised K2TaF7. Activity-pH diagrams for the Ta-K-F-H2O system explained the dissolution of Ta2O5 in fluoride solutions quite well and also the precipitation-recrystallisation of K2TaF7.H2O. X-ray diffraction and scanning electron microscopy confirmed the thermodynamic observations. It was concluded that the best precipitating agent for K2TaF7 from fluoride solutions is KF but a recrystallisation step in a HF environment produces purer, well-crystallised K2TaF7.H2O, eliminating oxy-salts and other impurities

Jun 21, 1905

By S. G. Ozkan

An investigation was carried out into the effect of physical parameters, such as particle size of the sample, residence time, solid/liquid ratio and impeller speed in the flotation cell, on the solubility in soft tap-water of colemanite (calcium-bearing borate) from Emet, in Turkey. Solubility increased steadily with residence time from 5 to 20 min but only minimally thereafter. There was a similar increase with impeller speed from 500 to 1 500 rev/min, beyond which a solubility of around 1.05 g/l was again established. There was a slight decline in solubility as the solid/liquid ratio was increased from 1 to 30%, with stable values around 1.05 g/l at a 20% ratio, while a sharp decrease was observed with decrease in size down to the -20 micrometre fraction. The effect of solubility should be taken into account if the application of a wet-processing method is being considered for the ore, while it can also result in losses of material during handling and storage

Jun 21, 1905

During the construction of storage caverns, and during their lifetime if the use to which they are put so requires, it is necessary to provide adequate ventilation to ensure the safety and comfort of the underground workforce. An analysis of likely contaminants during construction has indicated that where a large facility is situated in a rock mass of even moderate temperature climatic conditions are likely to be the limiting factor during most of the mining operation and atmospheric pollution when blasting is undertaken. Possible options for improvement are increased air flow, cooling of intake air and reduction of the heat source by altering the number and type of haulage units employed in the cavern. Local solutions are an alternative approach where heat problems are confined to a few specific locations

Aug 1, 1994

By M. J. Scoble, L. M. Daneshmend, C. Hendricks

Paper presented at a meeting on: Artificial intelligence in the minerals sector, held in Nottingham, UK, 20 April 1993. An attempt is made to relate emerging technologies to education and training requirements by examining the nature of the Canadian mining industry's human resources. Particular attention is given to the trends evident in mine automation and their likely impact on instructional needs. The characteristics of "computer-aided instruction" systems are reviewed and related to the implementation and support of mine-wide monitoring and communication networks, which are seen as fundamental to the eventual automation of underground hardrock mines

Apr 1, 1994

By F. Tailoka

Bi was electrorefined from alloys containing 10-90 wt% Pb, together with Cu and Ag as minor impurities, in a basic cell and in a recessed-channel cell with 27.5:72.5 NaCl-PbCl electrolyte at 450-470 degrees C and 10 000-20 000 A/m2. The voltage in the basic cell was as high as 9 V, with some carryover of Bi to the cathode observed, whereas in the recessed-channel cell it was as low as 285-635 mV. Flow patterns observed in a room-temperature model indicated that the recesses provide both static liquid hold-up and good mixing of the alloy, enhancing cell performance in combination with the reduced anode-cathode distance of 0.90 mm. The purity of the resulting anode product is as high as 99.9%

Aug 1, 1995

By J. A. Finch, Zhenghe Xu, Z. A. Zhou

A particle-bubble collision model was used to investigate the minimum recovery zone height, H(r,min) required for flotation columns. The criterion used to define H(r,min) is that height which gives unit collision probability. It is shown that H(r,min) is determined by particle and bubble size, gas hold-up and bubble-bubble interaction. Under typical operating conditions, for flotation of particles less that 10 micrometres in size H(r,min) is greater than 10 m, but it reduces to less than 1 m for particles greater than 100 micrometres

Aug 1, 1995

By G. G. Barbante

An understanding of the thermodynamics of smelting copper anode slimes is a prerequisite for improvements to the process. During slimes smelting, a silver-copper selenide matte is formed and subsequently oxidised to silver metal. As part of a series of investigations, molten silver selenide matte was oxidised at 1 100 degrees C with pure oxygen. The chemical potential diagram for the system was developed and used for qualitative prediction of the results of the experiments. A simple, computational thermodynamic model of converting is presented, the adjustable parameters of which were determined by matching the model with the experimental results. The practical usefulness of the model was demonstrated by predicting the effect on silver recovery of smelting temperature and of using either oxygen or air as the smelting gas

Jun 21, 1905

By B. E. Burakov, S. D. Lupal, O. A. R. Thalhammer, B. Saini-Eidukat

Electric-pulse disintegration is a mineral separation technique that liberates all mineral grains from any igneous or metamorphic rock irrespective of its lithology or grain-size distribution. The normal mechanical crushing of whole-rock samples is replaced by the rending effect of an explosion, produced by applying an electric current from a high-voltage power source. A voltage greater than the 100 kV necessary for the electrical breakdown of rock samples is achieved by using capacitors charged in parallel, but discharged in series. The sample sits in a water bath and the rapid distribution of electric pulses leads to an explosion which occurs preferentially along grain boundaries of the sample. Individual, undamaged mineral grains can be recovered in their original shape and form regardless of grain size. Examples are given of the liberation and concentration of important accessory minerals from different rock types. The examples show the recovery of diamond from two types of non-kimberlitic host rock in Popigai and Kumdykol in Kazakhstan and platinum group minerals associated with chromitites from the Konjdor intrusion and sulphides from intrusions in the Kola Peninsula in Russia

Apr 1, 1995

By Xiao Min You, D. R. Swonbourne

Smelting of Cu anode slimes involves the use of a slag to hold the oxidised Cu, but some Ag is also inevitably oxidised to the slag. The solubility of Ag in sodium silicate slags at 1 100 and 1 150 degrees C has now been determined over a very wide range of oxygen partial pressures. Silver was found to be present in the slags both as neutral atoms and as AgO(0.5). The activity coefficient for atomic Ag was a very strong function of slag composition and temperature, whereas that for AgO(0.5) was much less affected by slag composition and was almost independent of temperature over the limited range examined. The results reveal that the dissolved Ag cannot be fully recovered by reduction of the slag with very reducing gases

Jun 21, 1905

By G. S. Camm

Gwynfynydd is a small, high-grade black shale-hosted vein-gold deposit. The Chidlaw Link Zone is the only area being mined and contains 24 000 t ore grading 15.2 g/t gold. Within the Link Zone a complex vein structure occurs consisting of a mother vein up to 5 m thick and narrow (less than 0.5 m) leader veins. The former shows minor variations in dip, strike and thickness, whereas the latter show marked changes in all three. The leader veins are hosted within the footwall zone of the mother vein and both are composed of quartz with galena, sphalerite, chalcopyrite, pyrite and minor arsenopyrite. The vein system is transected by a series of cross-vein and intra-vein dip-slip faults. Pockets of gold occur at vein intersections or branches and within the complex footwall zone and are often related to variations in vein attitude and/or geometry. The Chidlaw Link Zone displays a complex, erratic distribution of gold mineralisation and a multi-stage history of structural activity, fluid flow and mineral deposition

Jun 18, 1905

By S. G. Tsimas, A. K. Moutsatsou, G. K. Parissakis, M. A. Komiotou

For Greek kaolin producers, a considerable proportion of whose output is from deposits containing more than 4 wt% Fe2O3, the colouring resulting from iron oxide impurity represents a serious problem that necessitates upgrading of the ore to meet commercial specifications. Autoclave leaching with oxalic acid for 1 h at 120 degrees C and 5-6 bar was shown to reduce Fe2O3 by up to 90% without affecting the structure of the kaolin, which maintained its physicochemical properties. The iron oxalate product can either be removed from solution or precipitated as iron hydroxide with recycling of the oxalic acid

Aug 1, 1995

By G. G. Barbante

Anode slimes produced during copper electrorefining are a valuable source of silver, gold, selenium and tellurium. The conventional pyrometallurgical process for treating slimes involves preliminary leaching in sulphuric acid followed by smelting in a reverberatory furnace with fluxes, but it is slow and has many recycle streams. The chemistry of the phases and the reactions that occur in slimes smelting are poorly understood and and this prevents major improvements to the process. Laboratory-scale experiments were conducted using unleached slimes, with and without the addition of fluxes and under neutral, oxidising and reducing conditions. Results show that selenium is readily removed as gaseous selenium dioxide and that molten Cu-Ag-Se-O phases form when fluxes are added. Oxidation-refining of these phases by air injection and flux addition can result in the formation of silver suitable for further electrorefining

Aug 1, 1995